diff mbox series

dt-bindings: spi: brcm,spi-bcm-qspi: convert to the json-schema

Message ID 20210415220201.16429-1-zajec5@gmail.com (mailing list archive)
State Superseded
Headers show
Series dt-bindings: spi: brcm,spi-bcm-qspi: convert to the json-schema | expand

Commit Message

Rafał Miłecki April 15, 2021, 10:02 p.m. UTC
From: Rafał Miłecki <rafal@milecki.pl>

This helps validating DTS files.

Changes that require mentioning:
1. reg-names
   "mspi_regs" and "bspi_regs" were renamed to "mspi" and "bspi" as that
   is what's used in DTS files and in Linux driver
2. interrupt-names
   Names were reordered. "mspi_done" has to go first as it's always
   required.
3. spi-rx-bus-width
   Property description was dropped as it's part of the
   spi-controller.yaml
4. Examples:
   * flash0@0 was a duplicated node and got dropped
   * regs and interrupts were formatted and reordered to match yaml
   * <0x1c> was replaced with <&gic>

This rewritten binding validates cleanly using the  "dt_binding_check".
Some Linux stored DTS files will require reordering regs and interrupts
to make dtbs_check happy.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
 .../bindings/spi/brcm,spi-bcm-qspi.txt        | 245 -----------------
 .../bindings/spi/brcm,spi-bcm-qspi.yaml       | 246 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 247 insertions(+), 246 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml

Comments

Florian Fainelli April 16, 2021, 12:32 a.m. UTC | #1
On 4/15/2021 3:02 PM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> This helps validating DTS files.
> 
> Changes that require mentioning:
> 1. reg-names
>    "mspi_regs" and "bspi_regs" were renamed to "mspi" and "bspi" as that
>    is what's used in DTS files and in Linux driver
> 2. interrupt-names
>    Names were reordered. "mspi_done" has to go first as it's always
>    required.
> 3. spi-rx-bus-width
>    Property description was dropped as it's part of the
>    spi-controller.yaml
> 4. Examples:
>    * flash0@0 was a duplicated node and got dropped
>    * regs and interrupts were formatted and reordered to match yaml
>    * <0x1c> was replaced with <&gic>
> 
> This rewritten binding validates cleanly using the  "dt_binding_check".
> Some Linux stored DTS files will require reordering regs and interrupts
> to make dtbs_check happy.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

Thanks a lot for doing that, do you mind adding Kamal as a maintainer
for that binding if you have to send a v2?
--
Florian
Rafał Miłecki April 16, 2021, 6:21 a.m. UTC | #2
On 2021-04-16 02:32, Florian Fainelli wrote:
> On 4/15/2021 3:02 PM, Rafał Miłecki wrote:
>> From: Rafał Miłecki <rafal@milecki.pl>
>> 
>> This helps validating DTS files.
>> 
>> Changes that require mentioning:
>> 1. reg-names
>>    "mspi_regs" and "bspi_regs" were renamed to "mspi" and "bspi" as 
>> that
>>    is what's used in DTS files and in Linux driver
>> 2. interrupt-names
>>    Names were reordered. "mspi_done" has to go first as it's always
>>    required.
>> 3. spi-rx-bus-width
>>    Property description was dropped as it's part of the
>>    spi-controller.yaml
>> 4. Examples:
>>    * flash0@0 was a duplicated node and got dropped
>>    * regs and interrupts were formatted and reordered to match yaml
>>    * <0x1c> was replaced with <&gic>
>> 
>> This rewritten binding validates cleanly using the  
>> "dt_binding_check".
>> Some Linux stored DTS files will require reordering regs and 
>> interrupts
>> to make dtbs_check happy.
>> 
>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> 
> Thanks a lot for doing that, do you mind adding Kamal as a maintainer
> for that binding if you have to send a v2?

I wasn't sure if I can just add someone else like that. He's already
maintainer according to the MAINTAINERS though, so I guess I'm safe to
do that. Sending V2.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt
deleted file mode 100644
index d99a9cf3336b..000000000000
--- a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt
+++ /dev/null
@@ -1,245 +0,0 @@ 
-Broadcom SPI controller
-
-The Broadcom SPI controller is a SPI master found on various SOCs, including
-BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits
-of :
- MSPI : SPI master controller can read and write to a SPI slave device
- BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration
-	for flash reads and be configured to do single, double, quad lane
-	io with 3-byte and 4-byte addressing support.
-
- Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP.
- MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance
- of a MSPI master without the BSPI to use with non flash slave devices that
- use SPI protocol.
-
-Required properties:
-
-- #address-cells:
-    Must be <1>, as required by generic SPI binding.
-
-- #size-cells:
-    Must be <0>, also as required by generic SPI binding.
-
-- compatible:
-    Must be one of :
-    "brcm,spi-brcmstb-qspi", "brcm,spi-bcm-qspi" : MSPI+BSPI on BRCMSTB SoCs
-    "brcm,spi-brcmstb-mspi", "brcm,spi-bcm-qspi" : Second Instance of MSPI
-						   BRCMSTB  SoCs
-    "brcm,spi-bcm7425-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-    			     			  			    BRCMSTB  SoCs
-    "brcm,spi-bcm7429-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-    			     			  			    BRCMSTB  SoCs
-    "brcm,spi-bcm7435-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-    			     			  			    BRCMSTB  SoCs
-    "brcm,spi-bcm7445-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-                                                                            BRCMSTB  SoCs
-    "brcm,spi-bcm7216-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-    			     			  			    BRCMSTB  SoCs
-    "brcm,spi-bcm7278-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
-    			     			  			    BRCMSTB  SoCs
-    "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi"     : MSPI+BSPI on Cygnus, NSP
-    "brcm,spi-ns2-qspi", "brcm,spi-bcm-qspi"     : NS2 SoCs
-
-- reg:
-    Define the bases and ranges of the associated I/O address spaces.
-    The required range is MSPI controller registers.
-
-- reg-names:
-    First name does not matter, but must be reserved for the MSPI controller
-    register range as mentioned in 'reg' above, and will typically contain
-    - "bspi_regs": BSPI register range, not required with compatible
-		   "spi-brcmstb-mspi"
-    - "mspi_regs": MSPI register range is required for compatible strings
-    - "intr_regs", "intr_status_reg" : Interrupt and status register for
-      NSP, NS2, Cygnus SoC
-
-- interrupts
-    The interrupts used by the MSPI and/or BSPI controller.
-
-- interrupt-names:
-    Names of interrupts associated with MSPI
-    - "mspi_halted" :
-    - "mspi_done": Indicates that the requested SPI operation is complete.
-    - "spi_lr_fullness_reached" : Linear read BSPI pipe full
-    - "spi_lr_session_aborted"  : Linear read BSPI pipe aborted
-    - "spi_lr_impatient" : Linear read BSPI requested when pipe empty
-    - "spi_lr_session_done" : Linear read BSPI session done
-
-- clocks:
-    A phandle to the reference clock for this block.
-
-Optional properties:
-
-
-- native-endian
-    Defined when using BE SoC and device uses BE register read/write
-
-Recommended optional m25p80 properties:
-- spi-rx-bus-width: Definition as per
-                    Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Examples:
-
-BRCMSTB SoC Example:
-
-  SPI Master (MSPI+BSPI) for SPI-NOR access:
-
-    spi@f03e3400 {
-		#address-cells = <0x1>;
-		#size-cells = <0x0>;
-		compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-bcm-qspi";
-		reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>;
-		reg-names = "cs_reg", "mspi", "bspi";
-		interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>;
-		interrupt-parent = <0x1c>;
-		interrupt-names = "mspi_halted",
-				  "mspi_done",
-				  "spi_lr_overread",
-				  "spi_lr_session_done",
-				  "spi_lr_impatient",
-				  "spi_lr_session_aborted",
-				  "spi_lr_fullness_reached";
-
-		clocks = <&hif_spi>;
-		clock-names = "sw_spi";
-
-		m25p80@0 {
-			#size-cells = <0x2>;
-			#address-cells = <0x2>;
-			compatible = "m25p80";
-			reg = <0x0>;
-			spi-max-frequency = <0x2625a00>;
-			spi-cpol;
-			spi-cpha;
-			m25p,fast-read;
-
-			flash0.bolt@0 {
-				reg = <0x0 0x0 0x0 0x100000>;
-			};
-
-			flash0.macadr@100000 {
-				reg = <0x0 0x100000 0x0 0x10000>;
-			};
-
-			flash0.nvram@110000 {
-				reg = <0x0 0x110000 0x0 0x10000>;
-			};
-
-			flash0.kernel@120000 {
-				reg = <0x0 0x120000 0x0 0x400000>;
-			};
-
-			flash0.devtree@520000 {
-				reg = <0x0 0x520000 0x0 0x10000>;
-			};
-
-			flash0.splash@530000 {
-				reg = <0x0 0x530000 0x0 0x80000>;
-			};
-
-			flash0@0 {
-				reg = <0x0 0x0 0x0 0x4000000>;
-			};
-		};
-	};
-
-
-    MSPI master for any SPI device :
-
-	spi@f0416000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&upg_fixed>;
-		compatible = "brcm,spi-brcmstb-mspi", "brcm,spi-bcm-qspi";
-		reg = <0xf0416000 0x180>;
-		reg-names = "mspi";
-		interrupts = <0x14>;
-		interrupt-parent = <&irq0_aon_intc>;
-		interrupt-names = "mspi_done";
-	};
-
-iProc SoC Example:
-
-    qspi: spi@18027200 {
-	compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
-	reg = <0x18027200 0x184>,
-	      <0x18027000 0x124>,
-	      <0x1811c408 0x004>,
-	      <0x180273a0 0x01c>;
-	reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg";
-	interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
-	interrupt-names =
-		     "spi_lr_fullness_reached",
-		     "spi_lr_session_aborted",
-		     "spi_lr_impatient",
-		     "spi_lr_session_done",
-		     "mspi_done",
-		     "mspi_halted";
-	clocks = <&iprocmed>;
-	clock-names = "iprocmed";
-	num-cs = <2>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-    };
-
-
- NS2 SoC Example:
-
-	       qspi: spi@66470200 {
-		       compatible = "brcm,spi-ns2-qspi", "brcm,spi-bcm-qspi";
-		       reg = <0x66470200 0x184>,
-			     <0x66470000 0x124>,
-			     <0x67017408 0x004>,
-			     <0x664703a0 0x01c>;
-		       reg-names = "mspi", "bspi", "intr_regs",
-			"intr_status_reg";
-		       interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;
-		       interrupt-names = "spi_l1_intr";
-			clocks = <&iprocmed>;
-			clock-names = "iprocmed";
-			num-cs = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-	       };
-
-
- m25p80 node for NSP, NS2
-
-	 &qspi {
-		      flash: m25p80@0 {
-		      #address-cells = <1>;
-		      #size-cells = <1>;
-		      compatible = "m25p80";
-		      reg = <0x0>;
-		      spi-max-frequency = <12500000>;
-		      m25p,fast-read;
-		      spi-cpol;
-		      spi-cpha;
-
-		      partition@0 {
-				  label = "boot";
-				  reg = <0x00000000 0x000a0000>;
-		      };
-
-		      partition@a0000 {
-				  label = "env";
-				  reg = <0x000a0000 0x00060000>;
-		      };
-
-		      partition@100000 {
-				  label = "system";
-				  reg = <0x00100000 0x00600000>;
-		      };
-
-		      partition@700000 {
-				  label = "rootfs";
-				  reg = <0x00700000 0x01900000>;
-		      };
-	};
diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
new file mode 100644
index 000000000000..f636965b1dce
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
@@ -0,0 +1,246 @@ 
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/brcm,spi-bcm-qspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom SPI controller
+
+maintainers:
+  - Rafał Miłecki <rafal@milecki.pl>
+
+description: |
+  The Broadcom SPI controller is a SPI master found on various SOCs, including
+  BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits
+  of:
+    MSPI : SPI master controller can read and write to a SPI slave device
+    BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration
+           for flash reads and be configured to do single, double, quad lane
+           io with 3-byte and 4-byte addressing support.
+
+  Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP.
+  MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance
+  of a MSPI master without the BSPI to use with non flash slave devices that
+  use SPI protocol.
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - description: Second Instance of MSPI BRCMSTB SoCs
+        items:
+          - enum:
+              - brcm,spi-bcm7425-qspi
+              - brcm,spi-bcm7429-qspi
+              - brcm,spi-bcm7435-qspi
+              - brcm,spi-bcm7445-qspi
+              - brcm,spi-bcm7216-qspi
+              - brcm,spi-bcm7278-qspi
+          - const: brcm,spi-bcm-qspi
+          - const: brcm,spi-brcmstb-mspi
+      - description: Second Instance of MSPI BRCMSTB SoCs
+        items:
+          - enum:
+              - brcm,spi-brcmstb-qspi
+              - brcm,spi-brcmstb-mspi
+              - brcm,spi-nsp-qspi
+              - brcm,spi-ns2-qspi
+          - const: brcm,spi-bcm-qspi
+
+  reg:
+    minItems: 1
+    maxItems: 5
+
+  reg-names:
+    minItems: 1
+    maxItems: 5
+    items:
+      - const: mspi
+      - const: bspi
+      - enum: [ intr_regs, intr_status_reg, cs_reg ]
+      - enum: [ intr_regs, intr_status_reg, cs_reg ]
+      - enum: [ intr_regs, intr_status_reg, cs_reg ]
+
+  interrupts:
+    minItems: 1
+    maxItems: 7
+
+  interrupt-names:
+    oneOf:
+      - minItems: 1
+        maxItems: 7
+        items:
+          - const: mspi_done
+          - const: mspi_halted
+          - const: spi_lr_fullness_reached
+          - const: spi_lr_session_aborted
+          - const: spi_lr_impatient
+          - const: spi_lr_session_done
+          - const: spi_lr_overread
+      - const: spi_l1_intr
+
+  clocks:
+    maxItems: 1
+    description: reference clock for this block
+
+  native-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Defined when using BE SoC and device uses BE register read/write
+
+unevaluatedProperties: false
+
+required:
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-names
+
+examples:
+  - | # BRCMSTB SoC: SPI Master (MSPI+BSPI) for SPI-NOR access
+    spi@f03e3400 {
+            compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-bcm-qspi";
+            reg = <0xf03e3400 0x188>, <0xf03e3200 0x50>, <0xf03e0920 0x4>;
+            reg-names = "mspi", "bspi", "cs_reg";
+            interrupts = <0x5 0x6 0x1 0x2 0x3 0x4 0x0>;
+            interrupt-parent = <&gic>;
+            interrupt-names = "mspi_done",
+                              "mspi_halted",
+                              "spi_lr_fullness_reached",
+                              "spi_lr_session_aborted",
+                              "spi_lr_impatient",
+                              "spi_lr_session_done",
+                              "spi_lr_overread";
+            clocks = <&hif_spi>;
+            clock-names = "sw_spi";
+            #address-cells = <0x1>;
+            #size-cells = <0x0>;
+
+            m25p80@0 {
+                    #size-cells = <0x2>;
+                    #address-cells = <0x2>;
+                    compatible = "m25p80";
+                    reg = <0x0>;
+                    spi-max-frequency = <0x2625a00>;
+                    spi-cpol;
+                    spi-cpha;
+                    m25p,fast-read;
+
+                    flash0.bolt@0 {
+                        reg = <0x0 0x0 0x0 0x100000>;
+                    };
+
+                    flash0.macadr@100000 {
+                        reg = <0x0 0x100000 0x0 0x10000>;
+                    };
+
+                    flash0.nvram@110000 {
+                        reg = <0x0 0x110000 0x0 0x10000>;
+                    };
+
+                    flash0.kernel@120000 {
+                        reg = <0x0 0x120000 0x0 0x400000>;
+                    };
+
+                    flash0.devtree@520000 {
+                        reg = <0x0 0x520000 0x0 0x10000>;
+                    };
+
+                    flash0.splash@530000 {
+                        reg = <0x0 0x530000 0x0 0x80000>;
+                    };
+            };
+    };
+  - | # BRCMSTB SoC: MSPI master for any SPI device
+    spi@f0416000 {
+            clocks = <&upg_fixed>;
+            compatible = "brcm,spi-brcmstb-mspi", "brcm,spi-bcm-qspi";
+            reg = <0xf0416000 0x180>;
+            reg-names = "mspi";
+            interrupts = <0x14>;
+            interrupt-parent = <&irq0_aon_intc>;
+            interrupt-names = "mspi_done";
+            #address-cells = <1>;
+            #size-cells = <0>;
+    };
+  - | # iProc SoC
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    spi@18027200 {
+            compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+            reg = <0x18027200 0x184>,
+                  <0x18027000 0x124>,
+                  <0x1811c408 0x004>,
+                  <0x180273a0 0x01c>;
+            reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+            interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "mspi_done",
+                              "mspi_halted",
+                              "spi_lr_fullness_reached",
+                              "spi_lr_session_aborted",
+                              "spi_lr_impatient",
+                              "spi_lr_session_done";
+            clocks = <&iprocmed>;
+            clock-names = "iprocmed";
+            num-cs = <2>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+    };
+  - | # NS2 SoC
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    qspi: spi@66470200 {
+            compatible = "brcm,spi-ns2-qspi", "brcm,spi-bcm-qspi";
+            reg = <0x66470200 0x184>,
+                  <0x66470000 0x124>,
+                  <0x67017408 0x004>,
+                  <0x664703a0 0x01c>;
+            reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+            interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "spi_l1_intr";
+            clocks = <&iprocmed>;
+            clock-names = "iprocmed";
+            num-cs = <2>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            flash: m25p80@0 {
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+                    compatible = "m25p80";
+                    reg = <0x0>;
+                    spi-max-frequency = <12500000>;
+                    m25p,fast-read;
+                    spi-cpol;
+                    spi-cpha;
+
+                    partition@0 {
+                        label = "boot";
+                        reg = <0x00000000 0x000a0000>;
+                    };
+
+                    partition@a0000 {
+                        label = "env";
+                        reg = <0x000a0000 0x00060000>;
+                    };
+
+                    partition@100000 {
+                        label = "system";
+                        reg = <0x00100000 0x00600000>;
+                    };
+
+                    partition@700000 {
+                        label = "rootfs";
+                        reg = <0x00700000 0x01900000>;
+                    };
+            };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index a1c2b56f4f90..6fb31a735a0f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3696,7 +3696,7 @@  BROADCOM SPI DRIVER
 M:	Kamal Dasu <kdasu.kdev@gmail.com>
 M:	bcm-kernel-feedback-list@broadcom.com
 S:	Maintained
-F:	Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt
+F:	Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
 F:	drivers/spi/spi-bcm-qspi.*
 F:	drivers/spi/spi-brcmstb-qspi.c
 F:	drivers/spi/spi-iproc-qspi.c