@@ -4092,6 +4092,13 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
if (__spi_validate_bits_per_word(ctlr, xfer->bits_per_word))
return -EINVAL;
+ /* DDR mode is supported only if controller has dtr_caps=true.
+ * default considered as SDR mode for SPI and QSPI controller.
+ * Note: This is applicable only to QSPI controller.
+ */
+ if (xfer->dtr_mode && !ctlr->dtr_caps)
+ return -EINVAL;
+
/*
* SPI transfer length should be multiple of SPI word size
* where SPI word size should be power-of-two multiple.
@@ -503,6 +503,8 @@ extern struct spi_device *spi_new_ancillary_device(struct spi_device *spi, u8 ch
* found.
* @put_offload: release the offload instance acquired by @get_offload.
* @mem_caps: controller capabilities for the handling of memory operations.
+ * @dtr_caps: true if controller has dtr(single/dual transfer rate) capability.
+ * QSPI based controller should fill this based on controller's capability.
* @unprepare_message: undo any work done by prepare_message().
* @target_abort: abort the ongoing transfer request on an SPI target controller
* @cs_gpiods: Array of GPIO descriptors to use as chip select lines; one per CS
@@ -746,6 +748,9 @@ struct spi_controller {
const struct spi_controller_mem_ops *mem_ops;
const struct spi_controller_mem_caps *mem_caps;
+ /* SPI or QSPI controller can set to true if supports SDR/DDR transfer rate */
+ bool dtr_caps;
+
struct spi_offload *(*get_offload)(struct spi_device *spi,
const struct spi_offload_config *config);
void (*put_offload)(struct spi_offload *offload);
@@ -998,6 +1003,7 @@ struct spi_res {
* processed the word, i.e. the "pre" timestamp should be taken before
* transmitting the "pre" word, and the "post" timestamp after receiving
* transmit confirmation from the controller for the "post" word.
+ * @dtr_mode: true if supports double transfer rate.
* @timestamped: true if the transfer has been timestamped
* @error: Error status logged by SPI controller driver.
*
@@ -1049,6 +1055,9 @@ struct spi_res {
* two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x)
* SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer.
*
+ * User may also set dtr_mode to true to use dual transfer mode if desired. if
+ * not, default considered as single transfer mode.
+ *
* The code that submits an spi_message (and its spi_transfers)
* to the lower layers is responsible for managing its memory.
* Zero-initialize every field you don't set up explicitly, to
@@ -1083,6 +1092,7 @@ struct spi_transfer {
unsigned tx_nbits:4;
unsigned rx_nbits:4;
unsigned timestamped:1;
+ bool dtr_mode;
#define SPI_NBITS_SINGLE 0x01 /* 1-bit transfer */
#define SPI_NBITS_DUAL 0x02 /* 2-bit transfer */
#define SPI_NBITS_QUAD 0x04 /* 4-bit transfer */
Introduce support for protocol drivers to specify whether a transfer should use single or dual transfer mode. Currently, the SPI controller cannot determine this information from the user, leading to potential limitations in transfer capabilities. Add a new field `dtr_mode` in the `spi_transfer` structure. The `dtr_mode` field allows protocol drivers to indicate if Double Transfer Rate (DTR) mode is supported for a given transfer. When `dtr_mode` is set to true, the SPI controller will use DTR mode; otherwise, it will default to single transfer mode. Introduce another field `dtr_caps` to indicate if the QSPI controller is capable of supporting DTR mode (SDR and DDR). By default, both `dtr_caps` and `dtr_mode` will be false. These flags manage the QSPI controller's DTR mode capabilities within the SPI framework. The QSPI controller driver uses these flags to configure single or double transfer rates using the controller register. The existing spi-mem driver helps configure the DTR mode but is limited to memory devices. There is no support available to set DTR mode for non-memory devices, e.g., touch or any generic SPI sensor. This change is backward compatible and doesn't break existing SPI or QSPI drivers. Changes include: - Addition of `dtr_mode` and `dtr_caps` fields in the `spi_transfer` structure. - Documentation updates to reflect the new `dtr_mode` and `dtr_caps` fields. Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com> --- Link to v1: https://lore.kernel.org/all/fbad733f-d034-4d63-ab82-ed867f0ed5d4@linaro.org/T/ Changes in V2: - Added dtr_caps flag to expose controllers capability and validate the dtr_mode against it. --- --- drivers/spi/spi.c | 7 +++++++ include/linux/spi/spi.h | 10 ++++++++++ 2 files changed, 17 insertions(+)