| Message ID | 42b82309e539e8a5523dca5364846c472ab9dcee.1442923630.git.anton_bondarenko@mentor.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
On Fri, Sep 25, 2015 at 07:57:14PM +0200, Anton Bondarenko wrote: > If SPI device supports DMA mode, but DMA controller is not yet > available due to e.g. a delay in the corresponding kernel module > initialization, retry to initialize SPI driver later on instead of > falling back into PIO only mode. > > Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> > Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com> > --- > drivers/spi/spi-imx.c | 12 +++++++++--- > 1 file changed, 9 insertions(+), 3 deletions(-) > > diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c > index 44d3cf0..1bf0739a 100644 > --- a/drivers/spi/spi-imx.c > +++ b/drivers/spi/spi-imx.c > @@ -1343,9 +1343,15 @@ static int spi_imx_probe(struct platform_device *pdev) > * Only validated on i.mx6 now, can remove the constrain if validated on > * other chips. > */ > - if (is_imx5x_ecspi(spi_imx) && > - spi_imx_sdma_init(&pdev->dev, spi_imx, master)) > - dev_err(&pdev->dev, "dma setup error,use pio instead\n"); > + if (is_imx5x_ecspi(spi_imx)) { > + ret = spi_imx_sdma_init(&pdev->dev, spi_imx, master); > + if (ret == -EPROBE_DEFER) > + goto out_clk_put; > + > + if (ret < 0) > + dev_err(&pdev->dev, "dma setup error %d, use pio\n", > + ret); > + } > > spi_imx->devtype_data->reset(spi_imx); > > -- > 2.5.2 > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index 44d3cf0..1bf0739a 100644 --- a/drivers/spi/spi-imx.c +++ b/drivers/spi/spi-imx.c @@ -1343,9 +1343,15 @@ static int spi_imx_probe(struct platform_device *pdev) * Only validated on i.mx6 now, can remove the constrain if validated on * other chips. */ - if (is_imx5x_ecspi(spi_imx) && - spi_imx_sdma_init(&pdev->dev, spi_imx, master)) - dev_err(&pdev->dev, "dma setup error,use pio instead\n"); + if (is_imx5x_ecspi(spi_imx)) { + ret = spi_imx_sdma_init(&pdev->dev, spi_imx, master); + if (ret == -EPROBE_DEFER) + goto out_clk_put; + + if (ret < 0) + dev_err(&pdev->dev, "dma setup error %d, use pio\n", + ret); + } spi_imx->devtype_data->reset(spi_imx);