@@ -275,7 +275,6 @@ real_start_efi:
b enable_boot_cpu_mm
primary_switched:
- bl setup_fixmap
#ifdef CONFIG_EARLY_PRINTK
/* Use a virtual address to access the UART. */
ldr x23, =EARLY_UART_VIRTUAL_ADDRESS
@@ -126,11 +126,6 @@
* Rebuild the boot pagetable's first-level entries. The structure
* is described in mm.c.
*
- * After the CPU enables paging it will add the fixmap mapping
- * to these page tables, however this may clash with the 1:1
- * mapping. So each CPU must rebuild the page tables here with
- * the 1:1 in place.
- *
* Inputs:
* x19: paddr(start)
* x20: phys offset
@@ -243,6 +238,16 @@ link_from_second_id:
create_table_entry boot_second_id, boot_third_id, x19, 2, x0, x1, x2
link_from_third_id:
create_mapping_entry boot_third_id, x19, x19, x0, x1, x2
+
+#ifdef CONFIG_EARLY_PRINTK
+ /* Add UART to the fixmap table */
+ ldr x0, =EARLY_UART_VIRTUAL_ADDRESS
+ /* x23: Early UART base physical address */
+ create_mapping_entry xen_fixmap, x0, x23, x1, x2, x3, type=PT_DEV_L3
+#endif
+ /* Map fixmap into boot_second */
+ ldr x0, =FIXMAP_ADDR(0)
+ create_table_entry boot_second, xen_fixmap, x0, 2, x1, x2, x3
ret
virtphys_clash:
@@ -402,39 +407,6 @@ identity_mapping_removed:
ret
ENDPROC(remove_identity_mapping)
-/*
- * Map the UART in the fixmap (when earlyprintk is used) and hook the
- * fixmap table in the page tables.
- *
- * The fixmap cannot be mapped in create_page_tables because it may
- * clash with the 1:1 mapping.
- *
- * Inputs:
- * x20: Physical offset
- * x23: Early UART base physical address
- *
- * Clobbers x0 - x3
- */
-ENTRY(setup_fixmap)
-#ifdef CONFIG_EARLY_PRINTK
- /* Add UART to the fixmap table */
- ldr x0, =EARLY_UART_VIRTUAL_ADDRESS
- create_mapping_entry xen_fixmap, x0, x23, x1, x2, x3, type=PT_DEV_L3
-#endif
- /* Map fixmap into boot_second */
- ldr x0, =FIXMAP_ADDR(0)
- create_table_entry boot_second, xen_fixmap, x0, 2, x1, x2, x3
- /* Ensure any page table updates made above have occurred. */
- dsb nshst
- /*
- * The fixmap area will be used soon after. So ensure no hardware
- * translation happens before the dsb completes.
- */
- isb
-
- ret
-ENDPROC(setup_fixmap)
-
/* Fail-stop */
fail: PRINT("- Boot failed -\r\n")
1: wfe
The original assembly setup_fixmap() is actually doing two seperate tasks, one is enabling the early UART when earlyprintk on, and the other is to set up the fixmap (even when earlyprintk is off). Per discussion in [1], since commit 9d267c049d92 ("xen/arm64: Rework the memory layout"), there is no chance that the fixmap and the mapping of early UART will clash with the 1:1 mapping. Therefore the mapping of both the fixmap and the early UART can be moved to the end of create_pagetables(). [1] https://lore.kernel.org/xen-devel/78862bb8-fd7f-5a51-a7ae-3c5b5998ed80@xen.org/ Signed-off-by: Henry Wang <Henry.Wang@arm.com> Reviewed-by: Julien Grall <jgrall@amazon.com> --- v6: - Drop the "No functional change intended." sentence in commit msg. - Add Julien's Reviewed-by tag. v5: - Refine the title and commit message. - Drop the "not applied" in-code comment about the 1:1 mapping clash on top of create_page_tables(). - Drop the unnecessary dsb and isb from the original setup_fixmap(). v4: - Rework "[v3,12/52] xen/mmu: extract early uart mapping from setup_fixmap" --- xen/arch/arm/arm64/head.S | 1 - xen/arch/arm/arm64/mmu/head.S | 48 ++++++++--------------------------- 2 files changed, 10 insertions(+), 39 deletions(-)