| Message ID | b19768d1db24123c76e50a410965582502937bb4.1651684160.git.rahul.singh@arm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] arm/its: enable LPIs before mapping the collection table | expand |
Hi Rahul, On 04/05/2022 18:15, Rahul Singh wrote: > When Xen boots on the platform that implements the GIC 600, ITS > MAPC_LPI_OFF uncorrectable command error issue is observed. > > As per the GIC-600 TRM (Revision: r1p6) MAPC_LPI_OFF command error can > be reported if the MAPC command has tried to map a collection to a core > that does not have LPIs enabled. The definition of GICR.EnableLPIs > also suggests enabling the LPIs before sending any ITS command that > involves LPIs > > 0b0 LPI support is disabled. Any doorbell interrupt generated as a > result of a write to a virtual LPI register must be discarded, > and any ITS translation requests or commands involving LPIs in > this Redistributor are ignored. > > 0b1 LPI support is enabled. > > To fix the MAPC command error issue, enable the LPIs using > GICR_CTLR.EnableLPIs before mapping the collection table. > > gicv3_enable_lpis() is using writel_relaxed(), write to the GICR_CTLR > register may not be visible before gicv3_its_setup_collection() send the > MAPC command. Use wmb() after writel_relaxed() to make sure register > write to enable LPIs is visible. > > Signed-off-by: Rahul Singh <rahul.singh@arm.com> Acked-by: Julien Grall <jgrall@amazon.com> Cheers,
Hi Rahul, > On 4 May 2022, at 18:15, Rahul Singh <Rahul.Singh@arm.com> wrote: > > When Xen boots on the platform that implements the GIC 600, ITS > MAPC_LPI_OFF uncorrectable command error issue is observed. > > As per the GIC-600 TRM (Revision: r1p6) MAPC_LPI_OFF command error can > be reported if the MAPC command has tried to map a collection to a core > that does not have LPIs enabled. The definition of GICR.EnableLPIs > also suggests enabling the LPIs before sending any ITS command that > involves LPIs > > 0b0 LPI support is disabled. Any doorbell interrupt generated as a > result of a write to a virtual LPI register must be discarded, > and any ITS translation requests or commands involving LPIs in > this Redistributor are ignored. > > 0b1 LPI support is enabled. > > To fix the MAPC command error issue, enable the LPIs using > GICR_CTLR.EnableLPIs before mapping the collection table. > > gicv3_enable_lpis() is using writel_relaxed(), write to the GICR_CTLR > register may not be visible before gicv3_its_setup_collection() send the > MAPC command. Use wmb() after writel_relaxed() to make sure register > write to enable LPIs is visible. > > Signed-off-by: Rahul Singh <rahul.singh@arm.com> Reviewed-by: Bertrand Marquis <bertrand.marquis@arm.com> Cheers Bertrand
On 06/05/2022 12:28, Bertrand Marquis wrote: >> On 4 May 2022, at 18:15, Rahul Singh <Rahul.Singh@arm.com> wrote: >> >> When Xen boots on the platform that implements the GIC 600, ITS >> MAPC_LPI_OFF uncorrectable command error issue is observed. >> >> As per the GIC-600 TRM (Revision: r1p6) MAPC_LPI_OFF command error can >> be reported if the MAPC command has tried to map a collection to a core >> that does not have LPIs enabled. The definition of GICR.EnableLPIs >> also suggests enabling the LPIs before sending any ITS command that >> involves LPIs >> >> 0b0 LPI support is disabled. Any doorbell interrupt generated as a >> result of a write to a virtual LPI register must be discarded, >> and any ITS translation requests or commands involving LPIs in >> this Redistributor are ignored. >> >> 0b1 LPI support is enabled. >> >> To fix the MAPC command error issue, enable the LPIs using >> GICR_CTLR.EnableLPIs before mapping the collection table. >> >> gicv3_enable_lpis() is using writel_relaxed(), write to the GICR_CTLR >> register may not be visible before gicv3_its_setup_collection() send the >> MAPC command. Use wmb() after writel_relaxed() to make sure register >> write to enable LPIs is visible. >> >> Signed-off-by: Rahul Singh <rahul.singh@arm.com> > Reviewed-by: Bertrand Marquis <bertrand.marquis@arm.com> Committed. Thanks! Cheers,
diff --git a/xen/arch/arm/gic-v3.c b/xen/arch/arm/gic-v3.c index 3c472ed768..64b36cec25 100644 --- a/xen/arch/arm/gic-v3.c +++ b/xen/arch/arm/gic-v3.c @@ -696,6 +696,9 @@ static bool gicv3_enable_lpis(void) val = readl_relaxed(GICD_RDIST_BASE + GICR_CTLR); writel_relaxed(val | GICR_CTLR_ENABLE_LPIS, GICD_RDIST_BASE + GICR_CTLR); + /* Make sure the GIC has seen the above */ + wmb(); + return true; } @@ -812,11 +815,11 @@ static int gicv3_cpu_init(void) /* If the host has any ITSes, enable LPIs now. */ if ( gicv3_its_host_has_its() ) { + if ( !gicv3_enable_lpis() ) + return -EBUSY; ret = gicv3_its_setup_collection(smp_processor_id()); if ( ret ) return ret; - if ( !gicv3_enable_lpis() ) - return -EBUSY; } /* Set priority on PPI and SGI interrupts */
When Xen boots on the platform that implements the GIC 600, ITS MAPC_LPI_OFF uncorrectable command error issue is observed. As per the GIC-600 TRM (Revision: r1p6) MAPC_LPI_OFF command error can be reported if the MAPC command has tried to map a collection to a core that does not have LPIs enabled. The definition of GICR.EnableLPIs also suggests enabling the LPIs before sending any ITS command that involves LPIs 0b0 LPI support is disabled. Any doorbell interrupt generated as a result of a write to a virtual LPI register must be discarded, and any ITS translation requests or commands involving LPIs in this Redistributor are ignored. 0b1 LPI support is enabled. To fix the MAPC command error issue, enable the LPIs using GICR_CTLR.EnableLPIs before mapping the collection table. gicv3_enable_lpis() is using writel_relaxed(), write to the GICR_CTLR register may not be visible before gicv3_its_setup_collection() send the MAPC command. Use wmb() after writel_relaxed() to make sure register write to enable LPIs is visible. Signed-off-by: Rahul Singh <rahul.singh@arm.com> --- v2 changes: - Add more info about issue in commit msg and specification details. - Use wmb() after writel_relaxed() to make sure register write to enable LPIs is visible --- xen/arch/arm/gic-v3.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)