From patchwork Mon Jan 30 06:35:35 2023 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Sae X-Patchwork-Id: 13120423 X-Patchwork-Delegate: kuba@kernel.org Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 047B5C54EED for ; Mon, 30 Jan 2023 06:36:06 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S235756AbjA3GgB (ORCPT ); Mon, 30 Jan 2023 01:36:01 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:49030 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S235384AbjA3Gf7 (ORCPT ); Mon, 30 Jan 2023 01:35:59 -0500 Received: from out28-5.mail.aliyun.com (out28-5.mail.aliyun.com [115.124.28.5]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 7B7F51ABD4; Sun, 29 Jan 2023 22:35:57 -0800 (PST) X-Alimail-AntiSpam: AC=CONTINUE;BC=0.1810407|-1;CH=green;DM=|CONTINUE|false|;DS=CONTINUE|ham_system_inform|0.0757899-0.000710198-0.9235;FP=0|0|0|0|0|-1|-1|-1;HT=ay29a033018047212;MF=frank.sae@motor-comm.com;NM=1;PH=DS;RN=18;RT=18;SR=0;TI=SMTPD_---.R4fCYBp_1675060550; Received: from sun-VirtualBox..(mailfrom:Frank.Sae@motor-comm.com fp:SMTPD_---.R4fCYBp_1675060550) by smtp.aliyun-inc.com; Mon, 30 Jan 2023 14:35:52 +0800 From: Frank Sae To: Peter Geis , Andrew Lunn , Heiner Kallweit , Russell King , "David S . Miller" , Eric Dumazet , Jakub Kicinski , Paolo Abeni , Rob Herring , Krzysztof Kozlowski , yanhong.wang@starfivetech.com Cc: xiaogang.fan@motor-comm.com, fei.zhang@motor-comm.com, hua.sun@motor-comm.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Frank , devicetree@vger.kernel.org Subject: [PATCH net-next v3 1/5] dt-bindings: net: Add Motorcomm yt8xxx ethernet phy Date: Mon, 30 Jan 2023 14:35:35 +0800 Message-Id: <20230130063539.3700-2-Frank.Sae@motor-comm.com> X-Mailer: git-send-email 2.34.1 In-Reply-To: <20230130063539.3700-1-Frank.Sae@motor-comm.com> References: <20230130063539.3700-1-Frank.Sae@motor-comm.com> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add a YAML binding document for the Motorcom yt8xxx Ethernet phy driver. Signed-off-by: Frank Sae --- .../bindings/net/motorcomm,yt8xxx.yaml | 102 ++++++++++++++++++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + MAINTAINERS | 1 + 3 files changed, 105 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml diff --git a/Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml b/Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml new file mode 100644 index 000000000000..8527576c15b3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/motorcomm,yt8xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MotorComm yt8xxx Ethernet PHY + +maintainers: + - frank sae + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + rx-internal-delay-ps: + description: | + RGMII RX Clock Delay used only when PHY operates in RGMII mode with + internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds. + enum: [ 0, 150, 300, 450, 600, 750, 900, 1050, 1200, 1350, 1500, 1650, + 1800, 1900, 1950, 2050, 2100, 2200, 2250, 2350, 2500, 2650, 2800, + 2950, 3100, 3250, 3400, 3550, 3700, 3850, 4000, 4150 ] + default: 1950 + + tx-internal-delay-ps: + description: | + RGMII TX Clock Delay used only when PHY operates in RGMII mode with + internal delay (phy-mode is 'rgmii-id' or 'rgmii-txid') in pico-seconds. + enum: [ 0, 150, 300, 450, 600, 750, 900, 1050, 1200, 1350, 1500, 1650, 1800, + 1950, 2100, 2250 ] + default: 150 + + motorcomm,clk-out-frequency-hz: + description: clock output on clock output pin. + enum: [0, 25000000, 125000000] + default: 0 + + motorcomm,keep-pll-enabled: + description: | + If set, keep the PLL enabled even if there is no link. Useful if you + want to use the clock output without an ethernet link. + type: boolean + + motorcomm,auto-sleep-disabled: + description: | + If set, PHY will not enter sleep mode and close AFE after unplug cable + for a timer. + type: boolean + + motorcomm,tx-clk-adj-enabled: + description: | + This configuration is mainly to adapt to VF2 with JH7110 SoC. + Useful if you want to use tx-clk-xxxx-inverted to adj the delay of tx clk. + type: boolean + + motorcomm,tx-clk-10-inverted: + description: | + Use original or inverted RGMII Transmit PHY Clock to drive the RGMII + Transmit PHY Clock delay train configuration when speed is 10Mbps. + type: boolean + + motorcomm,tx-clk-100-inverted: + description: | + Use original or inverted RGMII Transmit PHY Clock to drive the RGMII + Transmit PHY Clock delay train configuration when speed is 100Mbps. + type: boolean + + motorcomm,tx-clk-1000-inverted: + description: | + Use original or inverted RGMII Transmit PHY Clock to drive the RGMII + Transmit PHY Clock delay train configuration when speed is 1000Mbps. + type: boolean + +unevaluatedProperties: false + +examples: + - | + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + phy-mode = "rgmii-id"; + ethernet-phy@4 { + reg = <4>; + rx-internal-delay-ps = <2100>; + tx-internal-delay-ps = <150>; + motorcomm,clk-out-frequency-hz = <0>; + motorcomm,keep-pll-enabled; + motorcomm,auto-sleep-disabled; + }; + }; + - | + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + phy-mode = "rgmii"; + ethernet-phy@5 { + reg = <5>; + motorcomm,clk-out-frequency-hz = <125000000>; + motorcomm,keep-pll-enabled; + motorcomm,auto-sleep-disabled; + }; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 161766b1de50..99bb8594753c 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -847,6 +847,8 @@ patternProperties: description: Moortec Semiconductor Ltd. "^mosaixtech,.*": description: Mosaix Technologies, Inc. + "^motorcomm,.*": + description: MotorComm, Inc. "^motorola,.*": description: Motorola, Inc. "^moxa,.*": diff --git a/MAINTAINERS b/MAINTAINERS index f82dd8d43c2b..e2f9d935ce8d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14163,6 +14163,7 @@ M: Peter Geis M: Frank L: netdev@vger.kernel.org S: Maintained +F: Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml F: drivers/net/phy/motorcomm.c MOXA SMARTIO/INDUSTIO/INTELLIO SERIAL CARD From patchwork Mon Jan 30 06:35:36 2023 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Sae X-Patchwork-Id: 13120424 X-Patchwork-Delegate: kuba@kernel.org Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 673F6C54EAA for ; Mon, 30 Jan 2023 06:36:09 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S235762AbjA3GgD (ORCPT ); Mon, 30 Jan 2023 01:36:03 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:49038 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S235533AbjA3GgA (ORCPT ); Mon, 30 Jan 2023 01:36:00 -0500 Received: from out28-196.mail.aliyun.com (out28-196.mail.aliyun.com [115.124.28.196]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id E90D01ABD7; Sun, 29 Jan 2023 22:35:58 -0800 (PST) X-Alimail-AntiSpam: AC=CONTINUE;BC=0.3420512|-1;CH=green;DM=|CONTINUE|false|;DS=CONTINUE|ham_system_inform|0.15356-0.00644005-0.84;FP=0|0|0|0|0|-1|-1|-1;HT=ay29a033018047205;MF=frank.sae@motor-comm.com;NM=1;PH=DS;RN=18;RT=18;SR=0;TI=SMTPD_---.R4fCYFY_1675060552; Received: from sun-VirtualBox..(mailfrom:Frank.Sae@motor-comm.com fp:SMTPD_---.R4fCYFY_1675060552) by smtp.aliyun-inc.com; Mon, 30 Jan 2023 14:35:53 +0800 From: Frank Sae To: Peter Geis , Andrew Lunn , Heiner Kallweit , Russell King , "David S . Miller" , Eric Dumazet , Jakub Kicinski , Paolo Abeni , Rob Herring , Krzysztof Kozlowski , yanhong.wang@starfivetech.com Cc: xiaogang.fan@motor-comm.com, fei.zhang@motor-comm.com, hua.sun@motor-comm.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Frank , devicetree@vger.kernel.org Subject: [PATCH net-next v3 2/5] net: phy: Add BIT macro for Motorcomm yt8521/yt8531 gigabit ethernet phy Date: Mon, 30 Jan 2023 14:35:36 +0800 Message-Id: <20230130063539.3700-3-Frank.Sae@motor-comm.com> X-Mailer: git-send-email 2.34.1 In-Reply-To: <20230130063539.3700-1-Frank.Sae@motor-comm.com> References: <20230130063539.3700-1-Frank.Sae@motor-comm.com> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add BIT macro for Motorcomm yt8521/yt8531 gigabit ethernet phy. This is a preparatory patch. Add BIT macro for 0xA012 reg, and supplement for 0xA001 and 0xA003 reg. These will be used to support dts. Signed-off-by: Frank Sae Reviewed-by: Andrew Lunn --- drivers/net/phy/motorcomm.c | 55 ++++++++++++++++++++++++++++++++++--- 1 file changed, 51 insertions(+), 4 deletions(-) diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c index 685190db72de..5442eab54094 100644 --- a/drivers/net/phy/motorcomm.c +++ b/drivers/net/phy/motorcomm.c @@ -161,6 +161,11 @@ #define YT8521_CHIP_CONFIG_REG 0xA001 #define YT8521_CCR_SW_RST BIT(15) +/* 1b0 disable 1.9ns rxc clock delay *default* + * 1b1 enable 1.9ns rxc clock delay + */ +#define YT8521_CCR_RXC_DLY_EN BIT(8) +#define YT8521_CCR_RXC_DLY_1_900_NS 1900 #define YT8521_CCR_MODE_SEL_MASK (BIT(2) | BIT(1) | BIT(0)) #define YT8521_CCR_MODE_UTP_TO_RGMII 0 @@ -178,22 +183,41 @@ #define YT8521_MODE_POLL 0x3 #define YT8521_RGMII_CONFIG1_REG 0xA003 - +/* 1b0 use original tx_clk_rgmii *default* + * 1b1 use inverted tx_clk_rgmii. + */ +#define YT8521_RC1R_TX_CLK_SEL_INVERTED BIT(14) /* TX Gig-E Delay is bits 3:0, default 0x1 * TX Fast-E Delay is bits 7:4, default 0xf * RX Delay is bits 13:10, default 0x0 * Delay = 150ps * N * On = 2250ps, off = 0ps */ -#define YT8521_RC1R_RX_DELAY_MASK (0xF << 10) +#define YT8521_RC1R_RX_DELAY_MASK GENMASK(13, 10) #define YT8521_RC1R_RX_DELAY_EN (0xF << 10) #define YT8521_RC1R_RX_DELAY_DIS (0x0 << 10) -#define YT8521_RC1R_FE_TX_DELAY_MASK (0xF << 4) +#define YT8521_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4) #define YT8521_RC1R_FE_TX_DELAY_EN (0xF << 4) #define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << 4) -#define YT8521_RC1R_GE_TX_DELAY_MASK (0xF << 0) +#define YT8521_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0) #define YT8521_RC1R_GE_TX_DELAY_EN (0xF << 0) #define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << 0) +#define YT8521_RC1R_RGMII_0_000_NS 0 +#define YT8521_RC1R_RGMII_0_150_NS 1 +#define YT8521_RC1R_RGMII_0_300_NS 2 +#define YT8521_RC1R_RGMII_0_450_NS 3 +#define YT8521_RC1R_RGMII_0_600_NS 4 +#define YT8521_RC1R_RGMII_0_750_NS 5 +#define YT8521_RC1R_RGMII_0_900_NS 6 +#define YT8521_RC1R_RGMII_1_050_NS 7 +#define YT8521_RC1R_RGMII_1_200_NS 8 +#define YT8521_RC1R_RGMII_1_350_NS 9 +#define YT8521_RC1R_RGMII_1_500_NS 10 +#define YT8521_RC1R_RGMII_1_650_NS 11 +#define YT8521_RC1R_RGMII_1_800_NS 12 +#define YT8521_RC1R_RGMII_1_950_NS 13 +#define YT8521_RC1R_RGMII_2_100_NS 14 +#define YT8521_RC1R_RGMII_2_250_NS 15 #define YTPHY_MISC_CONFIG_REG 0xA006 #define YTPHY_MCR_FIBER_SPEED_MASK BIT(0) @@ -222,6 +246,29 @@ */ #define YTPHY_WCR_TYPE_PULSE BIT(0) +#define YTPHY_SYNCE_CFG_REG 0xA012 +#define YT8521_SCR_SYNCE_ENABLE BIT(5) +/* 1b0 output 25m clock + * 1b1 output 125m clock *default* + */ +#define YT8521_SCR_CLK_FRE_SEL_125M BIT(3) +#define YT8521_SCR_CLK_SRC_MASK GENMASK(2, 1) +#define YT8521_SCR_CLK_SRC_PLL_125M 0 +#define YT8521_SCR_CLK_SRC_UTP_RX 1 +#define YT8521_SCR_CLK_SRC_SDS_RX 2 +#define YT8521_SCR_CLK_SRC_REF_25M 3 +#define YT8531_SCR_SYNCE_ENABLE BIT(6) +/* 1b0 output 25m clock *default* + * 1b1 output 125m clock + */ +#define YT8531_SCR_CLK_FRE_SEL_125M BIT(4) +#define YT8531_SCR_CLK_SRC_MASK GENMASK(3, 1) +#define YT8531_SCR_CLK_SRC_PLL_125M 0 +#define YT8531_SCR_CLK_SRC_UTP_RX 1 +#define YT8531_SCR_CLK_SRC_SDS_RX 2 +#define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL 3 +#define YT8531_SCR_CLK_SRC_REF_25M 4 +#define YT8531_SCR_CLK_SRC_SSC_25M 5 #define YT8531S_SYNCE_CFG_REG 0xA012 #define YT8531S_SCR_SYNCE_ENABLE BIT(6) From patchwork Mon Jan 30 06:35:37 2023 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Sae X-Patchwork-Id: 13120427 X-Patchwork-Delegate: kuba@kernel.org Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 871F7C54EED for ; Mon, 30 Jan 2023 06:37:04 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S235413AbjA3GhD (ORCPT ); Mon, 30 Jan 2023 01:37:03 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:49166 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S235265AbjA3Ggy (ORCPT ); Mon, 30 Jan 2023 01:36:54 -0500 Received: from out28-146.mail.aliyun.com (out28-146.mail.aliyun.com [115.124.28.146]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 47C7226840; Sun, 29 Jan 2023 22:36:33 -0800 (PST) X-Alimail-AntiSpam: AC=CONTINUE;BC=0.07436454|-1;CH=green;DM=|CONTINUE|false|;DS=CONTINUE|ham_system_inform|0.0712192-0.000815318-0.927965;FP=0|0|0|0|0|-1|-1|-1;HT=ay29a033018047193;MF=frank.sae@motor-comm.com;NM=1;PH=DS;RN=18;RT=18;SR=0;TI=SMTPD_---.R4fCYJ6_1675060554; Received: from sun-VirtualBox..(mailfrom:Frank.Sae@motor-comm.com fp:SMTPD_---.R4fCYJ6_1675060554) by smtp.aliyun-inc.com; Mon, 30 Jan 2023 14:35:55 +0800 From: Frank Sae To: Peter Geis , Andrew Lunn , Heiner Kallweit , Russell King , "David S . Miller" , Eric Dumazet , Jakub Kicinski , Paolo Abeni , Rob Herring , Krzysztof Kozlowski , yanhong.wang@starfivetech.com Cc: xiaogang.fan@motor-comm.com, fei.zhang@motor-comm.com, hua.sun@motor-comm.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Frank , devicetree@vger.kernel.org Subject: [PATCH net-next v3 3/5] net: phy: Add dts support for Motorcomm yt8521 gigabit ethernet phy Date: Mon, 30 Jan 2023 14:35:37 +0800 Message-Id: <20230130063539.3700-4-Frank.Sae@motor-comm.com> X-Mailer: git-send-email 2.34.1 In-Reply-To: <20230130063539.3700-1-Frank.Sae@motor-comm.com> References: <20230130063539.3700-1-Frank.Sae@motor-comm.com> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add dts support for Motorcomm yt8521 gigabit ethernet phy. Add ytphy_rgmii_clk_delay_config function to support dst config for the delay of rgmii clk. This funciont is common for yt8521, yt8531s and yt8531. This patch has been verified on AM335x platform. Signed-off-by: Frank Sae --- drivers/net/phy/motorcomm.c | 253 ++++++++++++++++++++++++++++-------- 1 file changed, 199 insertions(+), 54 deletions(-) diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c index 5442eab54094..4a5ca846adeb 100644 --- a/drivers/net/phy/motorcomm.c +++ b/drivers/net/phy/motorcomm.c @@ -10,6 +10,7 @@ #include #include #include +#include #define PHY_ID_YT8511 0x0000010a #define PHY_ID_YT8521 0x0000011A @@ -187,21 +188,9 @@ * 1b1 use inverted tx_clk_rgmii. */ #define YT8521_RC1R_TX_CLK_SEL_INVERTED BIT(14) -/* TX Gig-E Delay is bits 3:0, default 0x1 - * TX Fast-E Delay is bits 7:4, default 0xf - * RX Delay is bits 13:10, default 0x0 - * Delay = 150ps * N - * On = 2250ps, off = 0ps - */ #define YT8521_RC1R_RX_DELAY_MASK GENMASK(13, 10) -#define YT8521_RC1R_RX_DELAY_EN (0xF << 10) -#define YT8521_RC1R_RX_DELAY_DIS (0x0 << 10) #define YT8521_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4) -#define YT8521_RC1R_FE_TX_DELAY_EN (0xF << 4) -#define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << 4) #define YT8521_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0) -#define YT8521_RC1R_GE_TX_DELAY_EN (0xF << 0) -#define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << 0) #define YT8521_RC1R_RGMII_0_000_NS 0 #define YT8521_RC1R_RGMII_0_150_NS 1 #define YT8521_RC1R_RGMII_0_300_NS 2 @@ -274,6 +263,10 @@ /* Extended Register end */ +#define YTPHY_DTS_OUTPUT_CLK_DIS 0 +#define YTPHY_DTS_OUTPUT_CLK_25M 25000000 +#define YTPHY_DTS_OUTPUT_CLK_125M 125000000 + struct yt8521_priv { /* combo_advertising is used for case of YT8521 in combo mode, * this means that yt8521 may work in utp or fiber mode which depends @@ -640,6 +633,142 @@ static int yt8521_write_page(struct phy_device *phydev, int page) return ytphy_modify_ext(phydev, YT8521_REG_SPACE_SELECT_REG, mask, set); }; +/** + * struct ytphy_cfg_reg_map - map a config value to a register value + * @cfg: value in device configuration + * @reg: value in the register + */ +struct ytphy_cfg_reg_map { + u32 cfg; + u32 reg; +}; + +static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = { + /* for tx delay / rx delay with YT8521_CCR_RXC_DLY_EN is not set. */ + { 0, YT8521_RC1R_RGMII_0_000_NS }, + { 150, YT8521_RC1R_RGMII_0_150_NS }, /* default tx delay */ + { 300, YT8521_RC1R_RGMII_0_300_NS }, + { 450, YT8521_RC1R_RGMII_0_450_NS }, + { 600, YT8521_RC1R_RGMII_0_600_NS }, + { 750, YT8521_RC1R_RGMII_0_750_NS }, + { 900, YT8521_RC1R_RGMII_0_900_NS }, + { 1050, YT8521_RC1R_RGMII_1_050_NS }, + { 1200, YT8521_RC1R_RGMII_1_200_NS }, + { 1350, YT8521_RC1R_RGMII_1_350_NS }, + { 1500, YT8521_RC1R_RGMII_1_500_NS }, + { 1650, YT8521_RC1R_RGMII_1_650_NS }, + { 1800, YT8521_RC1R_RGMII_1_800_NS }, + { 1950, YT8521_RC1R_RGMII_1_950_NS }, /* default rx delay */ + { 2100, YT8521_RC1R_RGMII_2_100_NS }, + { 2250, YT8521_RC1R_RGMII_2_250_NS }, + + /* only for rx delay with YT8521_CCR_RXC_DLY_EN is set. */ + { 0 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_000_NS }, + { 150 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_150_NS }, + { 300 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_300_NS }, + { 450 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_450_NS }, + { 600 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_600_NS }, + { 750 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_750_NS }, + { 900 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_900_NS }, + { 1050 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_050_NS }, + { 1200 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_200_NS }, + { 1350 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_350_NS }, + { 1500 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_500_NS }, + { 1650 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_650_NS }, + { 1800 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_800_NS }, + { 1950 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_950_NS }, + { 2100 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_100_NS }, + { 2250 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_250_NS } +}; + +static u32 ytphy_get_delay_reg_value(struct phy_device *phydev, + const char *prop_name, + const struct ytphy_cfg_reg_map *tbl, + int tb_size, + u16 *rxc_dly_en, + u32 dflt) +{ + struct device_node *node = phydev->mdio.dev.of_node; + int tb_size_half = tb_size / 2; + u32 val; + int i; + + if (of_property_read_u32(node, prop_name, &val)) + goto err_dts_val; + + /* when rxc_dly_en is NULL, it is get the delay for tx, only half of + * tb_size is valid. + */ + if (!rxc_dly_en) + tb_size = tb_size_half; + + for (i = 0; i < tb_size; i++) { + if (tbl[i].cfg == val) { + if (rxc_dly_en && i < tb_size_half) + *rxc_dly_en = 0; + return tbl[i].reg; + } + } + + phydev_warn(phydev, "Unsupported value %d for %s using default (%u)\n", + val, prop_name, dflt); + +err_dts_val: + /* when rxc_dly_en is not NULL, it is get the delay for rx. + * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps, + * so YT8521_CCR_RXC_DLY_EN should not be set. + */ + if (rxc_dly_en) + *rxc_dly_en = 0; + + return dflt; +} + +static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev) +{ + int tb_size = ARRAY_SIZE(ytphy_rgmii_delays); + u16 rxc_dly_en = YT8521_CCR_RXC_DLY_EN; + u32 rx_reg, tx_reg; + u16 mask, val = 0; + int ret; + + rx_reg = ytphy_get_delay_reg_value(phydev, "rx-internal-delay-ps", + ytphy_rgmii_delays, tb_size, + &rxc_dly_en, + YT8521_RC1R_RGMII_1_950_NS); + tx_reg = ytphy_get_delay_reg_value(phydev, "tx-internal-delay-ps", + ytphy_rgmii_delays, tb_size, NULL, + YT8521_RC1R_RGMII_0_150_NS); + + switch (phydev->interface) { + case PHY_INTERFACE_MODE_RGMII: + rxc_dly_en = 0; + break; + case PHY_INTERFACE_MODE_RGMII_RXID: + val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg); + break; + case PHY_INTERFACE_MODE_RGMII_TXID: + rxc_dly_en = 0; + val |= FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg); + break; + case PHY_INTERFACE_MODE_RGMII_ID: + val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg) | + FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg); + break; + default: /* do not support other modes */ + return -EOPNOTSUPP; + } + + ret = ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG, + YT8521_CCR_RXC_DLY_EN, rxc_dly_en); + if (ret < 0) + return ret; + + /* Generally, it is not necessary to adjust YT8521_RC1R_FE_TX_DELAY */ + mask = YT8521_RC1R_RX_DELAY_MASK | YT8521_RC1R_GE_TX_DELAY_MASK; + return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val); +} + /** * yt8521_probe() - read chip config then set suitable polling_mode * @phydev: a pointer to a &struct phy_device @@ -648,9 +777,12 @@ static int yt8521_write_page(struct phy_device *phydev, int page) */ static int yt8521_probe(struct phy_device *phydev) { + struct device_node *node = phydev->mdio.dev.of_node; struct device *dev = &phydev->mdio.dev; struct yt8521_priv *priv; int chip_config; + u16 mask, val; + u32 freq; int ret; priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); @@ -695,7 +827,45 @@ static int yt8521_probe(struct phy_device *phydev) return ret; } - return 0; + if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq)) + freq = YTPHY_DTS_OUTPUT_CLK_DIS; + + if (phydev->drv->phy_id == PHY_ID_YT8521) { + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8521_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_SRC_MASK | + YT8521_SCR_CLK_FRE_SEL_125M; + val = YT8521_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8521_SCR_CLK_SRC_MASK, + YT8521_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_SRC_MASK | + YT8521_SCR_CLK_FRE_SEL_125M; + val = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8521_SCR_CLK_SRC_MASK, + YT8521_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } + } else if (phydev->drv->phy_id == PHY_ID_YT8531S) { + return 0; + } else { + phydev_warn(phydev, "PHY id err\n"); + return -EINVAL; + } + + return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask, + val); } /** @@ -1180,61 +1350,36 @@ static int yt8521_resume(struct phy_device *phydev) */ static int yt8521_config_init(struct phy_device *phydev) { + struct device_node *node = phydev->mdio.dev.of_node; int old_page; int ret = 0; - u16 val; old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE); if (old_page < 0) goto err_restore_page; - switch (phydev->interface) { - case PHY_INTERFACE_MODE_RGMII: - val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS; - val |= YT8521_RC1R_RX_DELAY_DIS; - break; - case PHY_INTERFACE_MODE_RGMII_RXID: - val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS; - val |= YT8521_RC1R_RX_DELAY_EN; - break; - case PHY_INTERFACE_MODE_RGMII_TXID: - val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN; - val |= YT8521_RC1R_RX_DELAY_DIS; - break; - case PHY_INTERFACE_MODE_RGMII_ID: - val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN; - val |= YT8521_RC1R_RX_DELAY_EN; - break; - case PHY_INTERFACE_MODE_SGMII: - break; - default: /* do not support other modes */ - ret = -EOPNOTSUPP; - goto err_restore_page; - } - /* set rgmii delay mode */ if (phydev->interface != PHY_INTERFACE_MODE_SGMII) { - ret = ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, - (YT8521_RC1R_RX_DELAY_MASK | - YT8521_RC1R_FE_TX_DELAY_MASK | - YT8521_RC1R_GE_TX_DELAY_MASK), - val); + ret = ytphy_rgmii_clk_delay_config(phydev); if (ret < 0) goto err_restore_page; } - /* disable auto sleep */ - ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG, - YT8521_ESC1R_SLEEP_SW, 0); - if (ret < 0) - goto err_restore_page; - - /* enable RXC clock when no wire plug */ - ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG, - YT8521_CGR_RX_CLK_EN, 0); - if (ret < 0) - goto err_restore_page; + if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) { + /* disable auto sleep */ + ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG, + YT8521_ESC1R_SLEEP_SW, 0); + if (ret < 0) + goto err_restore_page; + } + if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) { + /* enable RXC clock when no wire plug */ + ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG, + YT8521_CGR_RX_CLK_EN, 0); + if (ret < 0) + goto err_restore_page; + } err_restore_page: return phy_restore_page(phydev, old_page, ret); } From patchwork Mon Jan 30 06:35:38 2023 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Sae X-Patchwork-Id: 13120425 X-Patchwork-Delegate: kuba@kernel.org Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 7BA7DC636CB for ; Mon, 30 Jan 2023 06:36:12 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S235763AbjA3GgI (ORCPT ); Mon, 30 Jan 2023 01:36:08 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:49094 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S229653AbjA3GgD (ORCPT ); Mon, 30 Jan 2023 01:36:03 -0500 Received: from out28-169.mail.aliyun.com (out28-169.mail.aliyun.com [115.124.28.169]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 1D63E1ABD5; Sun, 29 Jan 2023 22:36:01 -0800 (PST) X-Alimail-AntiSpam: AC=CONTINUE;BC=0.08887874|-1;CH=green;DM=|CONTINUE|false|;DS=CONTINUE|ham_system_inform|0.0211176-0.234236-0.744646;FP=0|0|0|0|0|-1|-1|-1;HT=ay29a033018047204;MF=frank.sae@motor-comm.com;NM=1;PH=DS;RN=18;RT=18;SR=0;TI=SMTPD_---.R4fCYMm_1675060555; Received: from sun-VirtualBox..(mailfrom:Frank.Sae@motor-comm.com fp:SMTPD_---.R4fCYMm_1675060555) by smtp.aliyun-inc.com; Mon, 30 Jan 2023 14:35:57 +0800 From: Frank Sae To: Peter Geis , Andrew Lunn , Heiner Kallweit , Russell King , "David S . Miller" , Eric Dumazet , Jakub Kicinski , Paolo Abeni , Rob Herring , Krzysztof Kozlowski , yanhong.wang@starfivetech.com Cc: xiaogang.fan@motor-comm.com, fei.zhang@motor-comm.com, hua.sun@motor-comm.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Frank , devicetree@vger.kernel.org Subject: [PATCH net-next v3 4/5] net: phy: Add dts support for Motorcomm yt8531s gigabit ethernet phy Date: Mon, 30 Jan 2023 14:35:38 +0800 Message-Id: <20230130063539.3700-5-Frank.Sae@motor-comm.com> X-Mailer: git-send-email 2.34.1 In-Reply-To: <20230130063539.3700-1-Frank.Sae@motor-comm.com> References: <20230130063539.3700-1-Frank.Sae@motor-comm.com> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add dts support for Motorcomm yt8531s gigabit ethernet phy. Change yt8521_probe to support clk config of yt8531s. Becase yt8521_probe does the things which yt8531s is needed, so removed yt8531s function. This patch has been verified on AM335x platform with yt8531s board. Signed-off-by: Frank Sae Reviewed-by: Andrew Lunn --- drivers/net/phy/motorcomm.c | 51 ++++++++++++++++++++----------------- 1 file changed, 27 insertions(+), 24 deletions(-) diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c index 4a5ca846adeb..ee9cd72758d6 100644 --- a/drivers/net/phy/motorcomm.c +++ b/drivers/net/phy/motorcomm.c @@ -258,8 +258,6 @@ #define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL 3 #define YT8531_SCR_CLK_SRC_REF_25M 4 #define YT8531_SCR_CLK_SRC_SSC_25M 5 -#define YT8531S_SYNCE_CFG_REG 0xA012 -#define YT8531S_SCR_SYNCE_ENABLE BIT(6) /* Extended Register end */ @@ -858,7 +856,32 @@ static int yt8521_probe(struct phy_device *phydev) return -EINVAL; } } else if (phydev->drv->phy_id == PHY_ID_YT8531S) { - return 0; + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8531_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } } else { phydev_warn(phydev, "PHY id err\n"); return -EINVAL; @@ -868,26 +891,6 @@ static int yt8521_probe(struct phy_device *phydev) val); } -/** - * yt8531s_probe() - read chip config then set suitable polling_mode - * @phydev: a pointer to a &struct phy_device - * - * returns 0 or negative errno code - */ -static int yt8531s_probe(struct phy_device *phydev) -{ - int ret; - - /* Disable SyncE clock output by default */ - ret = ytphy_modify_ext_with_lock(phydev, YT8531S_SYNCE_CFG_REG, - YT8531S_SCR_SYNCE_ENABLE, 0); - if (ret < 0) - return ret; - - /* same as yt8521_probe */ - return yt8521_probe(phydev); -} - /** * ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp * @phydev: a pointer to a &struct phy_device @@ -1970,7 +1973,7 @@ static struct phy_driver motorcomm_phy_drvs[] = { PHY_ID_MATCH_EXACT(PHY_ID_YT8531S), .name = "YT8531S Gigabit Ethernet", .get_features = yt8521_get_features, - .probe = yt8531s_probe, + .probe = yt8521_probe, .read_page = yt8521_read_page, .write_page = yt8521_write_page, .get_wol = ytphy_get_wol, From patchwork Mon Jan 30 06:35:39 2023 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Sae X-Patchwork-Id: 13120426 X-Patchwork-Delegate: kuba@kernel.org Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 274E0C54EED for ; Mon, 30 Jan 2023 06:36:17 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S235808AbjA3GgP (ORCPT ); Mon, 30 Jan 2023 01:36:15 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:49166 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S235767AbjA3GgJ (ORCPT ); Mon, 30 Jan 2023 01:36:09 -0500 Received: from out29-153.mail.aliyun.com (out29-153.mail.aliyun.com [115.124.29.153]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 47FB826846; Sun, 29 Jan 2023 22:36:03 -0800 (PST) X-Alimail-AntiSpam: AC=CONTINUE;BC=0.07436331|-1;CH=green;DM=|CONTINUE|false|;DS=CONTINUE|ham_system_inform|0.00946298-0.254234-0.736303;FP=0|0|0|0|0|-1|-1|-1;HT=ay29a033018047194;MF=frank.sae@motor-comm.com;NM=1;PH=DS;RN=18;RT=18;SR=0;TI=SMTPD_---.R4fCYQh_1675060557; Received: from sun-VirtualBox..(mailfrom:Frank.Sae@motor-comm.com fp:SMTPD_---.R4fCYQh_1675060557) by smtp.aliyun-inc.com; Mon, 30 Jan 2023 14:35:58 +0800 From: Frank Sae To: Peter Geis , Andrew Lunn , Heiner Kallweit , Russell King , "David S . Miller" , Eric Dumazet , Jakub Kicinski , Paolo Abeni , Rob Herring , Krzysztof Kozlowski , yanhong.wang@starfivetech.com Cc: xiaogang.fan@motor-comm.com, fei.zhang@motor-comm.com, hua.sun@motor-comm.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Frank , devicetree@vger.kernel.org Subject: [PATCH net-next v3 5/5] net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy Date: Mon, 30 Jan 2023 14:35:39 +0800 Message-Id: <20230130063539.3700-6-Frank.Sae@motor-comm.com> X-Mailer: git-send-email 2.34.1 In-Reply-To: <20230130063539.3700-1-Frank.Sae@motor-comm.com> References: <20230130063539.3700-1-Frank.Sae@motor-comm.com> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have verified the driver on AM335x platform with yt8531 board. On the board, yt8531 gigabit ethernet phy works in utp mode, RGMII interface, supports 1000M/100M/10M speeds, and wol(magic package). Signed-off-by: Frank Sae --- drivers/net/phy/Kconfig | 2 +- drivers/net/phy/motorcomm.c | 208 +++++++++++++++++++++++++++++++++++- 2 files changed, 207 insertions(+), 3 deletions(-) diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index f5df2edc94a5..54874555c921 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -257,7 +257,7 @@ config MOTORCOMM_PHY tristate "Motorcomm PHYs" help Enables support for Motorcomm network PHYs. - Currently supports the YT8511, YT8521, YT8531S Gigabit Ethernet PHYs. + Currently supports YT85xx Gigabit Ethernet PHYs. config NATIONAL_PHY tristate "National Semiconductor PHYs" diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c index ee9cd72758d6..81a251815fb0 100644 --- a/drivers/net/phy/motorcomm.c +++ b/drivers/net/phy/motorcomm.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /* - * Motorcomm 8511/8521/8531S PHY driver. + * Motorcomm 8511/8521/8531/8531S PHY driver. * * Author: Peter Geis * Author: Frank @@ -14,6 +14,7 @@ #define PHY_ID_YT8511 0x0000010a #define PHY_ID_YT8521 0x0000011A +#define PHY_ID_YT8531 0x4f51e91b #define PHY_ID_YT8531S 0x4F51E91A /* YT8521/YT8531S Register Overview @@ -517,6 +518,61 @@ static int ytphy_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol) return phy_restore_page(phydev, old_page, ret); } +static int yt8531_set_wol(struct phy_device *phydev, + struct ethtool_wolinfo *wol) +{ + const u16 mac_addr_reg[] = { + YTPHY_WOL_MACADDR2_REG, + YTPHY_WOL_MACADDR1_REG, + YTPHY_WOL_MACADDR0_REG, + }; + const u8 *mac_addr; + u16 mask, val; + int ret; + u8 i; + + if (wol->wolopts & WAKE_MAGIC) { + mac_addr = phydev->attached_dev->dev_addr; + + /* Store the device address for the magic packet */ + for (i = 0; i < 3; i++) { + ret = ytphy_write_ext_with_lock(phydev, mac_addr_reg[i], + ((mac_addr[i * 2] << 8)) | + (mac_addr[i * 2 + 1])); + if (ret < 0) + return ret; + } + + /* Enable WOL feature */ + mask = YTPHY_WCR_PULSE_WIDTH_MASK | YTPHY_WCR_INTR_SEL; + val = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL; + val |= YTPHY_WCR_TYPE_PULSE | YTPHY_WCR_PULSE_WIDTH_672MS; + ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG, + mask, val); + if (ret < 0) + return ret; + + /* Enable WOL interrupt */ + ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, 0, + YTPHY_IER_WOL); + if (ret < 0) + return ret; + } else { + /* Disable WOL feature */ + mask = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL; + ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG, + mask, 0); + + /* Disable WOL interrupt */ + ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, + YTPHY_IER_WOL, 0); + if (ret < 0) + return ret; + } + + return 0; +} + static int yt8511_read_page(struct phy_device *phydev) { return __phy_read(phydev, YT8511_PAGE_SELECT); @@ -767,6 +823,17 @@ static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev) return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val); } +static int ytphy_rgmii_clk_delay_config_with_lock(struct phy_device *phydev) +{ + int ret; + + phy_lock_mdio_bus(phydev); + ret = ytphy_rgmii_clk_delay_config(phydev); + phy_unlock_mdio_bus(phydev); + + return ret; +} + /** * yt8521_probe() - read chip config then set suitable polling_mode * @phydev: a pointer to a &struct phy_device @@ -891,6 +958,43 @@ static int yt8521_probe(struct phy_device *phydev) val); } +static int yt8531_probe(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + u16 mask, val; + u32 freq; + + if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq)) + freq = YTPHY_DTS_OUTPUT_CLK_DIS; + + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8531_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } + + return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask, + val); +} + /** * ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp * @phydev: a pointer to a &struct phy_device @@ -1387,6 +1491,94 @@ static int yt8521_config_init(struct phy_device *phydev) return phy_restore_page(phydev, old_page, ret); } +static int yt8531_config_init(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + int ret; + + ret = ytphy_rgmii_clk_delay_config_with_lock(phydev); + if (ret < 0) + return ret; + + if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) { + /* disable auto sleep */ + ret = ytphy_modify_ext_with_lock(phydev, + YT8521_EXTREG_SLEEP_CONTROL1_REG, + YT8521_ESC1R_SLEEP_SW, 0); + if (ret < 0) + return ret; + } + + if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) { + /* enable RXC clock when no wire plug */ + ret = ytphy_modify_ext_with_lock(phydev, + YT8521_CLOCK_GATING_REG, + YT8521_CGR_RX_CLK_EN, 0); + if (ret < 0) + return ret; + } + + return 0; +} + +/** + * yt8531_link_change_notify() - Adjust the tx clock direction according to + * the current speed and dts config. + * @phydev: a pointer to a &struct phy_device + * + * NOTE: This function is only used to adapt to VF2 with JH7110 SoC. Please + * keep "motorcomm,tx-clk-adj-enabled" not exist in dts when the soc is not + * JH7110. + */ +static void yt8531_link_change_notify(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + bool tx_clk_adj_enabled = false; + bool tx_clk_1000_inverted; + bool tx_clk_100_inverted; + bool tx_clk_10_inverted; + u16 val = 0; + int ret; + + if (of_property_read_bool(node, "motorcomm,tx-clk-adj-enabled")) + tx_clk_adj_enabled = true; + + if (!tx_clk_adj_enabled) + return; + + if (of_property_read_bool(node, "motorcomm,tx-clk-10-inverted")) + tx_clk_10_inverted = true; + if (of_property_read_bool(node, "motorcomm,tx-clk-100-inverted")) + tx_clk_100_inverted = true; + if (of_property_read_bool(node, "motorcomm,tx-clk-1000-inverted")) + tx_clk_1000_inverted = true; + + if (phydev->speed < 0) + return; + + switch (phydev->speed) { + case SPEED_1000: + if (tx_clk_1000_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + case SPEED_100: + if (tx_clk_100_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + case SPEED_10: + if (tx_clk_10_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + default: + return; + } + + ret = ytphy_modify_ext_with_lock(phydev, YT8521_RGMII_CONFIG1_REG, + YT8521_RC1R_TX_CLK_SEL_INVERTED, val); + if (ret < 0) + phydev_warn(phydev, "Modify TX_CLK_SEL err:%d\n", ret); +} + /** * yt8521_prepare_fiber_features() - A small helper function that setup * fiber's features. @@ -1969,6 +2161,17 @@ static struct phy_driver motorcomm_phy_drvs[] = { .suspend = yt8521_suspend, .resume = yt8521_resume, }, + { + PHY_ID_MATCH_EXACT(PHY_ID_YT8531), + .name = "YT8531 Gigabit Ethernet", + .probe = yt8531_probe, + .config_init = yt8531_config_init, + .suspend = genphy_suspend, + .resume = genphy_resume, + .get_wol = ytphy_get_wol, + .set_wol = yt8531_set_wol, + .link_change_notify = yt8531_link_change_notify, + }, { PHY_ID_MATCH_EXACT(PHY_ID_YT8531S), .name = "YT8531S Gigabit Ethernet", @@ -1990,7 +2193,7 @@ static struct phy_driver motorcomm_phy_drvs[] = { module_phy_driver(motorcomm_phy_drvs); -MODULE_DESCRIPTION("Motorcomm 8511/8521/8531S PHY driver"); +MODULE_DESCRIPTION("Motorcomm 8511/8521/8531/8531S PHY driver"); MODULE_AUTHOR("Peter Geis"); MODULE_AUTHOR("Frank"); MODULE_LICENSE("GPL"); @@ -1998,6 +2201,7 @@ MODULE_LICENSE("GPL"); static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = { { PHY_ID_MATCH_EXACT(PHY_ID_YT8511) }, { PHY_ID_MATCH_EXACT(PHY_ID_YT8521) }, + { PHY_ID_MATCH_EXACT(PHY_ID_YT8531) }, { PHY_ID_MATCH_EXACT(PHY_ID_YT8531S) }, { /* sentinal */ } };