Message ID | 1436388361-11130-16-git-send-email-ville.syrjala@linux.intel.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On 07/09/2015 02:16 AM, ville.syrjala@linux.intel.com wrote: > From: Ville Syrjälä <ville.syrjala@linux.intel.com> > > At various points when changing the DPIO lane/phy power states, > construct an expected value of the DISPLAY_PHY_STATUS register > and compare it with the real thing. > > To construct the expected value we look at our shadow PHY_CONTROL > register value (which should match what we've just written to the > hardware), and we also need to look at the actual state of the cmn > power wells as a disabled power well causes the relevant LDO status > to be reported as 'on' in DISPLAY_PHY_STATUS. > > When initially powering up the PHY it performs various internal > calibrations for which it fully powers up. That means that if we check > for the expetected power state immediately upon releasing cmnreset we > would get the occasional false positive. But we can of course > poll until the expected value appears. It shouldn't be too long so > this shouldn't make modesets substantially longer. > > One extra complication is introduced when we cross the streams, ie. > drive port B with pipe B. In this case we trick CL2 (where the DPLL lives) > into life by temporaily powering up the lanes in the second channel, > and once the pipe is up and runnign we release the lane power override. > At that point the power state of CL2 has somehow gotten entangled with > the power state of the first channel. That means that constructing the > expected DISPLAY_PHY_STATUS value is a bit tricky since based on the > lane power states in the second channel, CL2 should also be powered > down. But we can use the DPLL enable bit to determine when CL2 should > be alive even if the lanes are powered down. However the power state > of CL2 isn't actually tied in with the DPLL state, but to the state > of the lanes in first channel, so we have to avoid checking the > expected state between shutting down the DPLL and powering down > the lanes in the first channel. So no calling assert_chv_phy_status() > before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(), > but after the write is a safe time to check. > > Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> > --- > drivers/gpu/drm/i915/i915_reg.h | 2 + > drivers/gpu/drm/i915/intel_runtime_pm.c | 126 +++++++++++++++++++++++++++----- > 2 files changed, 111 insertions(+), 17 deletions(-) > > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h > index 586a0f7..429105e 100644 > --- a/drivers/gpu/drm/i915/i915_reg.h > +++ b/drivers/gpu/drm/i915/i915_reg.h > @@ -2206,6 +2206,8 @@ enum skl_disp_power_wells { > #define PHY_COM_LANE_RESET_DEASSERT(phy) (1 << (phy)) > #define DISPLAY_PHY_STATUS (VLV_DISPLAY_BASE + 0x60104) > #define PHY_POWERGOOD(phy) (((phy) == DPIO_PHY0) ? (1<<31) : (1<<30)) > +#define PHY_STATUS_CMN_LDO(phy, ch) (1 << (6-(6*(phy)+3*(ch)))) > +#define PHY_STATUS_SPLINE_LDO(phy, ch, spline) (1 << (8-(6*(phy)+3*(ch)+(spline)))) > > /* > * The i830 generation, in LVDS mode, defines P1 as the bit number set within > diff --git a/drivers/gpu/drm/i915/intel_runtime_pm.c b/drivers/gpu/drm/i915/intel_runtime_pm.c > index a1d9676..e6f1b4ee 100644 > --- a/drivers/gpu/drm/i915/intel_runtime_pm.c > +++ b/drivers/gpu/drm/i915/intel_runtime_pm.c > @@ -942,6 +942,107 @@ static void vlv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > vlv_set_power_well(dev_priv, power_well, false); > } > > +#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) > + > +static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, > + int power_well_id) > +{ > + struct i915_power_domains *power_domains = &dev_priv->power_domains; > + struct i915_power_well *power_well; > + int i; > + > + for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { > + if (power_well->data == power_well_id) > + return power_well; > + } > + > + return NULL; > +} > + > +#define BITS_SET(val, bits) (((val) & (bits)) == (bits)) > + > +static void assert_chv_phy_status(struct drm_i915_private *dev_priv) > +{ > + struct i915_power_well *cmn_bc = > + lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC); > + struct i915_power_well *cmn_d = > + lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_D); > + u32 phy_control = dev_priv->chv_phy_control; > + u32 phy_status = 0; > + u32 tmp; > + > + if (cmn_bc->ops->is_enabled(dev_priv, cmn_bc)) { > + phy_status |= PHY_POWERGOOD(DPIO_PHY0); > + > + /* this assumes override is only used to enable lanes */ > + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH0)) == 0) > + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0); > + > + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH1)) == 0) > + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1); > + > + /* CL1 is on whenever anything is on in either channel */ > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0) | > + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1))) > + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH0); > + > + /* > + * The DPLLB check accounts for the pipe B + port A usage > + * with CL2 powered up but all the lanes in the second channel > + * powered down. > + */ > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1)) && > + (I915_READ(DPLL(PIPE_B)) & DPLL_VCO_ENABLE) == 0) > + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH1); > + > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH0))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 0); > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH0))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 1); > + > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH1))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 0); > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH1))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 1); > + } > + > + if (cmn_d->ops->is_enabled(dev_priv, cmn_d)) { > + phy_status |= PHY_POWERGOOD(DPIO_PHY1); > + > + /* this assumes override is only used to enable lanes */ > + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY1, DPIO_CH0)) == 0) > + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0); > + > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0))) > + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY1, DPIO_CH0); > + > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY1, DPIO_CH0))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 0); > + if (BITS_SET(phy_control, > + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY1, DPIO_CH0))) > + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 1); > + } > + > + /* > + * The PHY may be busy with some initial calibration and whatnot, > + * so the power state can take a while to actually change. > + */ > + if (wait_for((tmp = I915_READ(DISPLAY_PHY_STATUS)) == phy_status, 10)) > + WARN(phy_status != tmp, > + "Unexpected PHY_STATUS 0x%08x, expected 0x%08x (PHY_CONTROL=0x%08x)\n", > + tmp, phy_status, dev_priv->chv_phy_control); > +} > + > +#undef BITS_SET > + > static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, > struct i915_power_well *power_well) > { > @@ -998,6 +1099,8 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, > > DRM_DEBUG_KMS("Enabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", > phy, dev_priv->chv_phy_control); > + > + assert_chv_phy_status(dev_priv); > } > > static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > @@ -1024,6 +1127,8 @@ static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > > DRM_DEBUG_KMS("Disabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", > phy, dev_priv->chv_phy_control); > + > + assert_chv_phy_status(dev_priv); > } > > static void assert_chv_phy_powergate(struct drm_i915_private *dev_priv, enum dpio_phy phy, > @@ -1101,6 +1206,8 @@ bool chv_phy_powergate_ch(struct drm_i915_private *dev_priv, enum dpio_phy phy, > DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d (DPIO_PHY_CONTROL=0x%08x)\n", > phy, ch, dev_priv->chv_phy_control); > > + assert_chv_phy_status(dev_priv); > + > out: > mutex_unlock(&power_domains->lock); > > @@ -1130,6 +1237,8 @@ void chv_phy_powergate_lanes(struct intel_encoder *encoder, > DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d lanes 0x%x (PHY_CONTROL=0x%08x)\n", > phy, ch, mask, dev_priv->chv_phy_control); > > + assert_chv_phy_status(dev_priv); > + Patch looks fine with assertion at right places Reviewed-by: Deepak S <deepak.s@linux.intel.com> > assert_chv_phy_powergate(dev_priv, phy, ch, override, mask); > > mutex_unlock(&power_domains->lock); > @@ -1302,8 +1411,6 @@ void intel_display_power_put(struct drm_i915_private *dev_priv, > intel_runtime_pm_put(dev_priv); > } > > -#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) > - > #define HSW_ALWAYS_ON_POWER_DOMAINS ( \ > BIT(POWER_DOMAIN_PIPE_A) | \ > BIT(POWER_DOMAIN_TRANSCODER_EDP) | \ > @@ -1565,21 +1672,6 @@ static struct i915_power_well chv_power_wells[] = { > }, > }; > > -static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, > - int power_well_id) > -{ > - struct i915_power_domains *power_domains = &dev_priv->power_domains; > - struct i915_power_well *power_well; > - int i; > - > - for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { > - if (power_well->data == power_well_id) > - return power_well; > - } > - > - return NULL; > -} > - > bool intel_display_power_well_is_enabled(struct drm_i915_private *dev_priv, > int power_well_id) > {
On Thu, Aug 27, 2015 at 10:09:37AM +0530, Deepak wrote: > > > On 07/09/2015 02:16 AM, ville.syrjala@linux.intel.com wrote: > >From: Ville Syrjälä <ville.syrjala@linux.intel.com> > > > >At various points when changing the DPIO lane/phy power states, > >construct an expected value of the DISPLAY_PHY_STATUS register > >and compare it with the real thing. > > > >To construct the expected value we look at our shadow PHY_CONTROL > >register value (which should match what we've just written to the > >hardware), and we also need to look at the actual state of the cmn > >power wells as a disabled power well causes the relevant LDO status > >to be reported as 'on' in DISPLAY_PHY_STATUS. > > > >When initially powering up the PHY it performs various internal > >calibrations for which it fully powers up. That means that if we check > >for the expetected power state immediately upon releasing cmnreset we > >would get the occasional false positive. But we can of course > >poll until the expected value appears. It shouldn't be too long so > >this shouldn't make modesets substantially longer. > > > >One extra complication is introduced when we cross the streams, ie. > >drive port B with pipe B. In this case we trick CL2 (where the DPLL lives) > >into life by temporaily powering up the lanes in the second channel, > >and once the pipe is up and runnign we release the lane power override. > >At that point the power state of CL2 has somehow gotten entangled with > >the power state of the first channel. That means that constructing the > >expected DISPLAY_PHY_STATUS value is a bit tricky since based on the > >lane power states in the second channel, CL2 should also be powered > >down. But we can use the DPLL enable bit to determine when CL2 should > >be alive even if the lanes are powered down. However the power state > >of CL2 isn't actually tied in with the DPLL state, but to the state > >of the lanes in first channel, so we have to avoid checking the > >expected state between shutting down the DPLL and powering down > >the lanes in the first channel. So no calling assert_chv_phy_status() > >before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(), > >but after the write is a safe time to check. > > > >Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Remaining 3 patches pulled into dinq, thanks. -Daniel > >--- > > drivers/gpu/drm/i915/i915_reg.h | 2 + > > drivers/gpu/drm/i915/intel_runtime_pm.c | 126 +++++++++++++++++++++++++++----- > > 2 files changed, 111 insertions(+), 17 deletions(-) > > > >diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h > >index 586a0f7..429105e 100644 > >--- a/drivers/gpu/drm/i915/i915_reg.h > >+++ b/drivers/gpu/drm/i915/i915_reg.h > >@@ -2206,6 +2206,8 @@ enum skl_disp_power_wells { > > #define PHY_COM_LANE_RESET_DEASSERT(phy) (1 << (phy)) > > #define DISPLAY_PHY_STATUS (VLV_DISPLAY_BASE + 0x60104) > > #define PHY_POWERGOOD(phy) (((phy) == DPIO_PHY0) ? (1<<31) : (1<<30)) > >+#define PHY_STATUS_CMN_LDO(phy, ch) (1 << (6-(6*(phy)+3*(ch)))) > >+#define PHY_STATUS_SPLINE_LDO(phy, ch, spline) (1 << (8-(6*(phy)+3*(ch)+(spline)))) > > /* > > * The i830 generation, in LVDS mode, defines P1 as the bit number set within > >diff --git a/drivers/gpu/drm/i915/intel_runtime_pm.c b/drivers/gpu/drm/i915/intel_runtime_pm.c > >index a1d9676..e6f1b4ee 100644 > >--- a/drivers/gpu/drm/i915/intel_runtime_pm.c > >+++ b/drivers/gpu/drm/i915/intel_runtime_pm.c > >@@ -942,6 +942,107 @@ static void vlv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > > vlv_set_power_well(dev_priv, power_well, false); > > } > >+#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) > >+ > >+static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, > >+ int power_well_id) > >+{ > >+ struct i915_power_domains *power_domains = &dev_priv->power_domains; > >+ struct i915_power_well *power_well; > >+ int i; > >+ > >+ for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { > >+ if (power_well->data == power_well_id) > >+ return power_well; > >+ } > >+ > >+ return NULL; > >+} > >+ > >+#define BITS_SET(val, bits) (((val) & (bits)) == (bits)) > >+ > >+static void assert_chv_phy_status(struct drm_i915_private *dev_priv) > >+{ > >+ struct i915_power_well *cmn_bc = > >+ lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC); > >+ struct i915_power_well *cmn_d = > >+ lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_D); > >+ u32 phy_control = dev_priv->chv_phy_control; > >+ u32 phy_status = 0; > >+ u32 tmp; > >+ > >+ if (cmn_bc->ops->is_enabled(dev_priv, cmn_bc)) { > >+ phy_status |= PHY_POWERGOOD(DPIO_PHY0); > >+ > >+ /* this assumes override is only used to enable lanes */ > >+ if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH0)) == 0) > >+ phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0); > >+ > >+ if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH1)) == 0) > >+ phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1); > >+ > >+ /* CL1 is on whenever anything is on in either channel */ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0) | > >+ PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1))) > >+ phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH0); > >+ > >+ /* > >+ * The DPLLB check accounts for the pipe B + port A usage > >+ * with CL2 powered up but all the lanes in the second channel > >+ * powered down. > >+ */ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1)) && > >+ (I915_READ(DPLL(PIPE_B)) & DPLL_VCO_ENABLE) == 0) > >+ phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH1); > >+ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH0))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 0); > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH0))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 1); > >+ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH1))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 0); > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH1))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 1); > >+ } > >+ > >+ if (cmn_d->ops->is_enabled(dev_priv, cmn_d)) { > >+ phy_status |= PHY_POWERGOOD(DPIO_PHY1); > >+ > >+ /* this assumes override is only used to enable lanes */ > >+ if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY1, DPIO_CH0)) == 0) > >+ phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0); > >+ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0))) > >+ phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY1, DPIO_CH0); > >+ > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY1, DPIO_CH0))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 0); > >+ if (BITS_SET(phy_control, > >+ PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY1, DPIO_CH0))) > >+ phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 1); > >+ } > >+ > >+ /* > >+ * The PHY may be busy with some initial calibration and whatnot, > >+ * so the power state can take a while to actually change. > >+ */ > >+ if (wait_for((tmp = I915_READ(DISPLAY_PHY_STATUS)) == phy_status, 10)) > >+ WARN(phy_status != tmp, > >+ "Unexpected PHY_STATUS 0x%08x, expected 0x%08x (PHY_CONTROL=0x%08x)\n", > >+ tmp, phy_status, dev_priv->chv_phy_control); > >+} > >+ > >+#undef BITS_SET > >+ > > static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, > > struct i915_power_well *power_well) > > { > >@@ -998,6 +1099,8 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, > > DRM_DEBUG_KMS("Enabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", > > phy, dev_priv->chv_phy_control); > >+ > >+ assert_chv_phy_status(dev_priv); > > } > > static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > >@@ -1024,6 +1127,8 @@ static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, > > DRM_DEBUG_KMS("Disabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", > > phy, dev_priv->chv_phy_control); > >+ > >+ assert_chv_phy_status(dev_priv); > > } > > static void assert_chv_phy_powergate(struct drm_i915_private *dev_priv, enum dpio_phy phy, > >@@ -1101,6 +1206,8 @@ bool chv_phy_powergate_ch(struct drm_i915_private *dev_priv, enum dpio_phy phy, > > DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d (DPIO_PHY_CONTROL=0x%08x)\n", > > phy, ch, dev_priv->chv_phy_control); > >+ assert_chv_phy_status(dev_priv); > >+ > > out: > > mutex_unlock(&power_domains->lock); > >@@ -1130,6 +1237,8 @@ void chv_phy_powergate_lanes(struct intel_encoder *encoder, > > DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d lanes 0x%x (PHY_CONTROL=0x%08x)\n", > > phy, ch, mask, dev_priv->chv_phy_control); > >+ assert_chv_phy_status(dev_priv); > >+ > Patch looks fine with assertion at right places > Reviewed-by: Deepak S <deepak.s@linux.intel.com> > > assert_chv_phy_powergate(dev_priv, phy, ch, override, mask); > > mutex_unlock(&power_domains->lock); > >@@ -1302,8 +1411,6 @@ void intel_display_power_put(struct drm_i915_private *dev_priv, > > intel_runtime_pm_put(dev_priv); > > } > >-#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) > >- > > #define HSW_ALWAYS_ON_POWER_DOMAINS ( \ > > BIT(POWER_DOMAIN_PIPE_A) | \ > > BIT(POWER_DOMAIN_TRANSCODER_EDP) | \ > >@@ -1565,21 +1672,6 @@ static struct i915_power_well chv_power_wells[] = { > > }, > > }; > >-static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, > >- int power_well_id) > >-{ > >- struct i915_power_domains *power_domains = &dev_priv->power_domains; > >- struct i915_power_well *power_well; > >- int i; > >- > >- for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { > >- if (power_well->data == power_well_id) > >- return power_well; > >- } > >- > >- return NULL; > >-} > >- > > bool intel_display_power_well_is_enabled(struct drm_i915_private *dev_priv, > > int power_well_id) > > { > > _______________________________________________ > Intel-gfx mailing list > Intel-gfx@lists.freedesktop.org > http://lists.freedesktop.org/mailman/listinfo/intel-gfx
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 586a0f7..429105e 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -2206,6 +2206,8 @@ enum skl_disp_power_wells { #define PHY_COM_LANE_RESET_DEASSERT(phy) (1 << (phy)) #define DISPLAY_PHY_STATUS (VLV_DISPLAY_BASE + 0x60104) #define PHY_POWERGOOD(phy) (((phy) == DPIO_PHY0) ? (1<<31) : (1<<30)) +#define PHY_STATUS_CMN_LDO(phy, ch) (1 << (6-(6*(phy)+3*(ch)))) +#define PHY_STATUS_SPLINE_LDO(phy, ch, spline) (1 << (8-(6*(phy)+3*(ch)+(spline)))) /* * The i830 generation, in LVDS mode, defines P1 as the bit number set within diff --git a/drivers/gpu/drm/i915/intel_runtime_pm.c b/drivers/gpu/drm/i915/intel_runtime_pm.c index a1d9676..e6f1b4ee 100644 --- a/drivers/gpu/drm/i915/intel_runtime_pm.c +++ b/drivers/gpu/drm/i915/intel_runtime_pm.c @@ -942,6 +942,107 @@ static void vlv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, vlv_set_power_well(dev_priv, power_well, false); } +#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) + +static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, + int power_well_id) +{ + struct i915_power_domains *power_domains = &dev_priv->power_domains; + struct i915_power_well *power_well; + int i; + + for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { + if (power_well->data == power_well_id) + return power_well; + } + + return NULL; +} + +#define BITS_SET(val, bits) (((val) & (bits)) == (bits)) + +static void assert_chv_phy_status(struct drm_i915_private *dev_priv) +{ + struct i915_power_well *cmn_bc = + lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC); + struct i915_power_well *cmn_d = + lookup_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_D); + u32 phy_control = dev_priv->chv_phy_control; + u32 phy_status = 0; + u32 tmp; + + if (cmn_bc->ops->is_enabled(dev_priv, cmn_bc)) { + phy_status |= PHY_POWERGOOD(DPIO_PHY0); + + /* this assumes override is only used to enable lanes */ + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH0)) == 0) + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0); + + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY0, DPIO_CH1)) == 0) + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1); + + /* CL1 is on whenever anything is on in either channel */ + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH0) | + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1))) + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH0); + + /* + * The DPLLB check accounts for the pipe B + port A usage + * with CL2 powered up but all the lanes in the second channel + * powered down. + */ + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY0, DPIO_CH1)) && + (I915_READ(DPLL(PIPE_B)) & DPLL_VCO_ENABLE) == 0) + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY0, DPIO_CH1); + + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH0))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 0); + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH0))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH0, 1); + + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY0, DPIO_CH1))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 0); + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY0, DPIO_CH1))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY0, DPIO_CH1, 1); + } + + if (cmn_d->ops->is_enabled(dev_priv, cmn_d)) { + phy_status |= PHY_POWERGOOD(DPIO_PHY1); + + /* this assumes override is only used to enable lanes */ + if ((phy_control & PHY_CH_POWER_DOWN_OVRD_EN(DPIO_PHY1, DPIO_CH0)) == 0) + phy_control |= PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0); + + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xf, DPIO_PHY1, DPIO_CH0))) + phy_status |= PHY_STATUS_CMN_LDO(DPIO_PHY1, DPIO_CH0); + + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0x3, DPIO_PHY1, DPIO_CH0))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 0); + if (BITS_SET(phy_control, + PHY_CH_POWER_DOWN_OVRD(0xc, DPIO_PHY1, DPIO_CH0))) + phy_status |= PHY_STATUS_SPLINE_LDO(DPIO_PHY1, DPIO_CH0, 1); + } + + /* + * The PHY may be busy with some initial calibration and whatnot, + * so the power state can take a while to actually change. + */ + if (wait_for((tmp = I915_READ(DISPLAY_PHY_STATUS)) == phy_status, 10)) + WARN(phy_status != tmp, + "Unexpected PHY_STATUS 0x%08x, expected 0x%08x (PHY_CONTROL=0x%08x)\n", + tmp, phy_status, dev_priv->chv_phy_control); +} + +#undef BITS_SET + static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, struct i915_power_well *power_well) { @@ -998,6 +1099,8 @@ static void chv_dpio_cmn_power_well_enable(struct drm_i915_private *dev_priv, DRM_DEBUG_KMS("Enabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", phy, dev_priv->chv_phy_control); + + assert_chv_phy_status(dev_priv); } static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, @@ -1024,6 +1127,8 @@ static void chv_dpio_cmn_power_well_disable(struct drm_i915_private *dev_priv, DRM_DEBUG_KMS("Disabled DPIO PHY%d (PHY_CONTROL=0x%08x)\n", phy, dev_priv->chv_phy_control); + + assert_chv_phy_status(dev_priv); } static void assert_chv_phy_powergate(struct drm_i915_private *dev_priv, enum dpio_phy phy, @@ -1101,6 +1206,8 @@ bool chv_phy_powergate_ch(struct drm_i915_private *dev_priv, enum dpio_phy phy, DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d (DPIO_PHY_CONTROL=0x%08x)\n", phy, ch, dev_priv->chv_phy_control); + assert_chv_phy_status(dev_priv); + out: mutex_unlock(&power_domains->lock); @@ -1130,6 +1237,8 @@ void chv_phy_powergate_lanes(struct intel_encoder *encoder, DRM_DEBUG_KMS("Power gating DPIO PHY%d CH%d lanes 0x%x (PHY_CONTROL=0x%08x)\n", phy, ch, mask, dev_priv->chv_phy_control); + assert_chv_phy_status(dev_priv); + assert_chv_phy_powergate(dev_priv, phy, ch, override, mask); mutex_unlock(&power_domains->lock); @@ -1302,8 +1411,6 @@ void intel_display_power_put(struct drm_i915_private *dev_priv, intel_runtime_pm_put(dev_priv); } -#define POWER_DOMAIN_MASK (BIT(POWER_DOMAIN_NUM) - 1) - #define HSW_ALWAYS_ON_POWER_DOMAINS ( \ BIT(POWER_DOMAIN_PIPE_A) | \ BIT(POWER_DOMAIN_TRANSCODER_EDP) | \ @@ -1565,21 +1672,6 @@ static struct i915_power_well chv_power_wells[] = { }, }; -static struct i915_power_well *lookup_power_well(struct drm_i915_private *dev_priv, - int power_well_id) -{ - struct i915_power_domains *power_domains = &dev_priv->power_domains; - struct i915_power_well *power_well; - int i; - - for_each_power_well(i, power_well, POWER_DOMAIN_MASK, power_domains) { - if (power_well->data == power_well_id) - return power_well; - } - - return NULL; -} - bool intel_display_power_well_is_enabled(struct drm_i915_private *dev_priv, int power_well_id) {