| Message ID | 1449135010-8111-4-git-send-email-inki.dae@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hello Inki, On 12/03/2015 06:30 AM, Inki Dae wrote: > This patch updates a ports node binding for panel. > > With this, dp node can have a ports node which describes > a remote endpoint node that can be connected to panel or bridge > node. > > Signed-off-by: Inki Dae <inki.dae@samsung.com> > --- > .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++---- > 1 file changed, 24 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > index 64693f2..15b52cb 100644 > --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > @@ -66,8 +66,15 @@ Optional properties for dp-controller: > Hotplug detect GPIO. > Indicates which GPIO should be used for hotplug > detection > - -video interfaces: Device node can contain video interface port > - nodes according to [1]. > +Video interfaces: > + Device node can contain video interface port nodes according to [1]. > + The following are properties specific to those nodes: > + > + endpoint node connected to bridge or panel node: > + - remote-endpoint: specifies the endpoint in panel or bridge node. > + This node is required in all kinds of exynos dp > + to represent the connection between dp and bridge > + ,or dp and panel. > This is nice but I think the DT binding should also document that it uses a phandle to define the connection with the panel (but explain that is deprecated). If only so people looking at a DTS and then going to the DT binding can understand why there is two ways to define the same. > [1]: Documentation/devicetree/bindings/media/video-interfaces.txt > > @@ -111,9 +118,22 @@ Board Specific portion: > }; > > ports { > - port@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + These two properties are only needed when there is more than 2 ports and a reg property is used to number the port nodes but I don't think that's the case for Exynos DP and certainly is not the case in this example so I think you should just remove them. > + port { > dp_out: endpoint { > - remote-endpoint = <&bridge_in>; > + remote-endpoint = <&dp_in>; > + }; > + }; > + }; > + > + panel@0 { > + reg = <0>; > + ... > + port { > + dp_in: endpoint { > + remote-endpoint = <&dp_out>; > }; > }; > }; > The rest looks good to me so with the two changes feel free to add: Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards,
On Thu, Dec 03, 2015 at 06:30:10PM +0900, Inki Dae wrote: > This patch updates a ports node binding for panel. > > With this, dp node can have a ports node which describes > a remote endpoint node that can be connected to panel or bridge > node. > > Signed-off-by: Inki Dae <inki.dae@samsung.com> > --- > .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++---- > 1 file changed, 24 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > index 64693f2..15b52cb 100644 > --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt > @@ -66,8 +66,15 @@ Optional properties for dp-controller: > Hotplug detect GPIO. > Indicates which GPIO should be used for hotplug > detection > - -video interfaces: Device node can contain video interface port > - nodes according to [1]. > +Video interfaces: > + Device node can contain video interface port nodes according to [1]. > + The following are properties specific to those nodes: > + > + endpoint node connected to bridge or panel node: > + - remote-endpoint: specifies the endpoint in panel or bridge node. > + This node is required in all kinds of exynos dp > + to represent the connection between dp and bridge > + ,or dp and panel. Fix your punctuation. > > [1]: Documentation/devicetree/bindings/media/video-interfaces.txt > > @@ -111,9 +118,22 @@ Board Specific portion: > }; > > ports { > - port@0 { > + #address-cells = <1>; > + #size-cells = <0>; You don't need these. > + > + port { > dp_out: endpoint { > - remote-endpoint = <&bridge_in>; > + remote-endpoint = <&dp_in>; > + }; > + }; > + }; > + > + panel@0 { > + reg = <0>; Drop the @0 and reg as you only have 1. > + ... > + port { > + dp_in: endpoint { > + remote-endpoint = <&dp_out>; > }; > }; > }; > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Javier, 2015? 12? 03? 22:29? Javier Martinez Canillas ?(?) ? ?: > Hello Inki, > > On 12/03/2015 06:30 AM, Inki Dae wrote: >> This patch updates a ports node binding for panel. >> >> With this, dp node can have a ports node which describes >> a remote endpoint node that can be connected to panel or bridge >> node. >> >> Signed-off-by: Inki Dae <inki.dae@samsung.com> >> --- >> .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++---- >> 1 file changed, 24 insertions(+), 4 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> index 64693f2..15b52cb 100644 >> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> @@ -66,8 +66,15 @@ Optional properties for dp-controller: >> Hotplug detect GPIO. >> Indicates which GPIO should be used for hotplug >> detection >> - -video interfaces: Device node can contain video interface port >> - nodes according to [1]. >> +Video interfaces: >> + Device node can contain video interface port nodes according to [1]. >> + The following are properties specific to those nodes: >> + >> + endpoint node connected to bridge or panel node: >> + - remote-endpoint: specifies the endpoint in panel or bridge node. >> + This node is required in all kinds of exynos dp >> + to represent the connection between dp and bridge >> + ,or dp and panel. >> > > This is nice but I think the DT binding should also document that it uses > a phandle to define the connection with the panel (but explain that is > deprecated). If only so people looking at a DTS and then going to the DT > binding can understand why there is two ways to define the same. > >> [1]: Documentation/devicetree/bindings/media/video-interfaces.txt >> >> @@ -111,9 +118,22 @@ Board Specific portion: >> }; >> >> ports { >> - port@0 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + > > These two properties are only needed when there is more than 2 ports and > a reg property is used to number the port nodes but I don't think that's > the case for Exynos DP and certainly is not the case in this example so > I think you should just remove them. Right. I found out that the dp can have only one port outbound. Will remove them. > >> + port { >> dp_out: endpoint { >> - remote-endpoint = <&bridge_in>; >> + remote-endpoint = <&dp_in>; >> + }; >> + }; >> + }; >> + >> + panel@0 { >> + reg = <0>; >> + ... >> + port { >> + dp_in: endpoint { >> + remote-endpoint = <&dp_out>; >> }; >> }; >> }; >> > > The rest looks good to me so with the two changes feel free to add: > > Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Thanks, Inki Dae > > Best regards, > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, 2015? 12? 04? 08:38? Rob Herring ?(?) ? ?: > On Thu, Dec 03, 2015 at 06:30:10PM +0900, Inki Dae wrote: >> This patch updates a ports node binding for panel. >> >> With this, dp node can have a ports node which describes >> a remote endpoint node that can be connected to panel or bridge >> node. >> >> Signed-off-by: Inki Dae <inki.dae@samsung.com> >> --- >> .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++---- >> 1 file changed, 24 insertions(+), 4 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> index 64693f2..15b52cb 100644 >> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt >> @@ -66,8 +66,15 @@ Optional properties for dp-controller: >> Hotplug detect GPIO. >> Indicates which GPIO should be used for hotplug >> detection >> - -video interfaces: Device node can contain video interface port >> - nodes according to [1]. >> +Video interfaces: >> + Device node can contain video interface port nodes according to [1]. >> + The following are properties specific to those nodes: >> + >> + endpoint node connected to bridge or panel node: >> + - remote-endpoint: specifies the endpoint in panel or bridge node. >> + This node is required in all kinds of exynos dp >> + to represent the connection between dp and bridge >> + ,or dp and panel. > > Fix your punctuation. Right. > >> >> [1]: Documentation/devicetree/bindings/media/video-interfaces.txt >> >> @@ -111,9 +118,22 @@ Board Specific portion: >> }; >> >> ports { >> - port@0 { >> + #address-cells = <1>; >> + #size-cells = <0>; > > You don't need these. Ditto. > >> + >> + port { >> dp_out: endpoint { >> - remote-endpoint = <&bridge_in>; >> + remote-endpoint = <&dp_in>; >> + }; >> + }; >> + }; >> + >> + panel@0 { >> + reg = <0>; > > Drop the @0 and reg as you only have 1. Ditto. Thanks, Inki Dae > >> + ... >> + port { >> + dp_in: endpoint { >> + remote-endpoint = <&dp_out>; >> }; >> }; >> }; >> -- >> 1.9.1 >> > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index 64693f2..15b52cb 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -66,8 +66,15 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection - -video interfaces: Device node can contain video interface port - nodes according to [1]. +Video interfaces: + Device node can contain video interface port nodes according to [1]. + The following are properties specific to those nodes: + + endpoint node connected to bridge or panel node: + - remote-endpoint: specifies the endpoint in panel or bridge node. + This node is required in all kinds of exynos dp + to represent the connection between dp and bridge + ,or dp and panel. [1]: Documentation/devicetree/bindings/media/video-interfaces.txt @@ -111,9 +118,22 @@ Board Specific portion: }; ports { - port@0 { + #address-cells = <1>; + #size-cells = <0>; + + port { dp_out: endpoint { - remote-endpoint = <&bridge_in>; + remote-endpoint = <&dp_in>; + }; + }; + }; + + panel@0 { + reg = <0>; + ... + port { + dp_in: endpoint { + remote-endpoint = <&dp_out>; }; }; };
This patch updates a ports node binding for panel. With this, dp node can have a ports node which describes a remote endpoint node that can be connected to panel or bridge node. Signed-off-by: Inki Dae <inki.dae@samsung.com> --- .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++---- 1 file changed, 24 insertions(+), 4 deletions(-)