diff mbox

[3/3] dt-bindings: exynos-dp: update ports node binding for panel

Message ID 1449135010-8111-4-git-send-email-inki.dae@samsung.com (mailing list archive)
State New, archived
Headers show

Commit Message

Inki Dae Dec. 3, 2015, 9:30 a.m. UTC
This patch updates a ports node binding for panel.

With this, dp node can have a ports node which describes
a remote endpoint node that can be connected to panel or bridge
node.

Signed-off-by: Inki Dae <inki.dae@samsung.com>
---
 .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
 1 file changed, 24 insertions(+), 4 deletions(-)

Comments

Javier Martinez Canillas Dec. 3, 2015, 1:29 p.m. UTC | #1
Hello Inki,

On 12/03/2015 06:30 AM, Inki Dae wrote:
> This patch updates a ports node binding for panel.
> 
> With this, dp node can have a ports node which describes
> a remote endpoint node that can be connected to panel or bridge
> node.
> 
> Signed-off-by: Inki Dae <inki.dae@samsung.com>
> ---
>  .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
>  1 file changed, 24 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> index 64693f2..15b52cb 100644
> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>  		Hotplug detect GPIO.
>  			Indicates which GPIO should be used for hotplug
>  			detection
> -	-video interfaces: Device node can contain video interface port
> -			    nodes according to [1].
> +Video interfaces:
> +  Device node can contain video interface port nodes according to [1].
> +  The following are properties specific to those nodes:
> +
> +  endpoint node connected to bridge or panel node:
> +   - remote-endpoint: specifies the endpoint in panel or bridge node.
> +		      This node is required in all kinds of exynos dp
> +		      to represent the connection between dp and bridge
> +		      ,or dp and panel.
>

This is nice but I think the DT binding should also document that it uses
a phandle to define the connection with the panel (but explain that is
deprecated). If only so people looking at a DTS and then going to the DT
binding can understand why there is two ways to define the same.
  
>  [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>  
> @@ -111,9 +118,22 @@ Board Specific portion:
>  		};
>  
>  		ports {
> -			port@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +

These two properties are only needed when there is more than 2 ports and
a reg property is used to number the port nodes but I don't think that's
the case for Exynos DP and certainly is not the case in this example so
I think you should just remove them.

> +			port {
>  				dp_out: endpoint {
> -					remote-endpoint = <&bridge_in>;
> +					remote-endpoint = <&dp_in>;
> +				};
> +			};
> +		};
> +
> +		panel@0 {
> +			reg = <0>;
> +			...
> +			port {
> +				dp_in: endpoint {
> +					remote-endpoint = <&dp_out>;
>  				};
>  			};
>  		};
> 

The rest looks good to me so with the two changes feel free to add:

Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

Best regards,
Rob Herring (Arm) Dec. 3, 2015, 11:38 p.m. UTC | #2
On Thu, Dec 03, 2015 at 06:30:10PM +0900, Inki Dae wrote:
> This patch updates a ports node binding for panel.
> 
> With this, dp node can have a ports node which describes
> a remote endpoint node that can be connected to panel or bridge
> node.
> 
> Signed-off-by: Inki Dae <inki.dae@samsung.com>
> ---
>  .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
>  1 file changed, 24 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> index 64693f2..15b52cb 100644
> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>  		Hotplug detect GPIO.
>  			Indicates which GPIO should be used for hotplug
>  			detection
> -	-video interfaces: Device node can contain video interface port
> -			    nodes according to [1].
> +Video interfaces:
> +  Device node can contain video interface port nodes according to [1].
> +  The following are properties specific to those nodes:
> +
> +  endpoint node connected to bridge or panel node:
> +   - remote-endpoint: specifies the endpoint in panel or bridge node.
> +		      This node is required in all kinds of exynos dp
> +		      to represent the connection between dp and bridge
> +		      ,or dp and panel.

Fix your punctuation.

>  
>  [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>  
> @@ -111,9 +118,22 @@ Board Specific portion:
>  		};
>  
>  		ports {
> -			port@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;

You don't need these.

> +
> +			port {
>  				dp_out: endpoint {
> -					remote-endpoint = <&bridge_in>;
> +					remote-endpoint = <&dp_in>;
> +				};
> +			};
> +		};
> +
> +		panel@0 {
> +			reg = <0>;

Drop the @0 and reg as you only have 1.

> +			...
> +			port {
> +				dp_in: endpoint {
> +					remote-endpoint = <&dp_out>;
>  				};
>  			};
>  		};
> -- 
> 1.9.1
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Inki Dae Dec. 4, 2015, 9:07 a.m. UTC | #3
Hi Javier,

2015? 12? 03? 22:29? Javier Martinez Canillas ?(?) ? ?:
> Hello Inki,
> 
> On 12/03/2015 06:30 AM, Inki Dae wrote:
>> This patch updates a ports node binding for panel.
>>
>> With this, dp node can have a ports node which describes
>> a remote endpoint node that can be connected to panel or bridge
>> node.
>>
>> Signed-off-by: Inki Dae <inki.dae@samsung.com>
>> ---
>>  .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
>>  1 file changed, 24 insertions(+), 4 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> index 64693f2..15b52cb 100644
>> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>>  		Hotplug detect GPIO.
>>  			Indicates which GPIO should be used for hotplug
>>  			detection
>> -	-video interfaces: Device node can contain video interface port
>> -			    nodes according to [1].
>> +Video interfaces:
>> +  Device node can contain video interface port nodes according to [1].
>> +  The following are properties specific to those nodes:
>> +
>> +  endpoint node connected to bridge or panel node:
>> +   - remote-endpoint: specifies the endpoint in panel or bridge node.
>> +		      This node is required in all kinds of exynos dp
>> +		      to represent the connection between dp and bridge
>> +		      ,or dp and panel.
>>
> 
> This is nice but I think the DT binding should also document that it uses
> a phandle to define the connection with the panel (but explain that is
> deprecated). If only so people looking at a DTS and then going to the DT
> binding can understand why there is two ways to define the same.
>   
>>  [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>>  
>> @@ -111,9 +118,22 @@ Board Specific portion:
>>  		};
>>  
>>  		ports {
>> -			port@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
> 
> These two properties are only needed when there is more than 2 ports and
> a reg property is used to number the port nodes but I don't think that's
> the case for Exynos DP and certainly is not the case in this example so
> I think you should just remove them.

Right. I found out that the dp can have only one port outbound. Will remove them.

> 
>> +			port {
>>  				dp_out: endpoint {
>> -					remote-endpoint = <&bridge_in>;
>> +					remote-endpoint = <&dp_in>;
>> +				};
>> +			};
>> +		};
>> +
>> +		panel@0 {
>> +			reg = <0>;
>> +			...
>> +			port {
>> +				dp_in: endpoint {
>> +					remote-endpoint = <&dp_out>;
>>  				};
>>  			};
>>  		};
>>
> 
> The rest looks good to me so with the two changes feel free to add:
> 
> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

Thanks,
Inki Dae

> 
> Best regards,
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Inki Dae Dec. 4, 2015, 9:08 a.m. UTC | #4
Hi Rob,

2015? 12? 04? 08:38? Rob Herring ?(?) ? ?:
> On Thu, Dec 03, 2015 at 06:30:10PM +0900, Inki Dae wrote:
>> This patch updates a ports node binding for panel.
>>
>> With this, dp node can have a ports node which describes
>> a remote endpoint node that can be connected to panel or bridge
>> node.
>>
>> Signed-off-by: Inki Dae <inki.dae@samsung.com>
>> ---
>>  .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
>>  1 file changed, 24 insertions(+), 4 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> index 64693f2..15b52cb 100644
>> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>>  		Hotplug detect GPIO.
>>  			Indicates which GPIO should be used for hotplug
>>  			detection
>> -	-video interfaces: Device node can contain video interface port
>> -			    nodes according to [1].
>> +Video interfaces:
>> +  Device node can contain video interface port nodes according to [1].
>> +  The following are properties specific to those nodes:
>> +
>> +  endpoint node connected to bridge or panel node:
>> +   - remote-endpoint: specifies the endpoint in panel or bridge node.
>> +		      This node is required in all kinds of exynos dp
>> +		      to represent the connection between dp and bridge
>> +		      ,or dp and panel.
> 
> Fix your punctuation.

Right. 

> 
>>  
>>  [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>>  
>> @@ -111,9 +118,22 @@ Board Specific portion:
>>  		};
>>  
>>  		ports {
>> -			port@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
> 
> You don't need these.

Ditto.

> 
>> +
>> +			port {
>>  				dp_out: endpoint {
>> -					remote-endpoint = <&bridge_in>;
>> +					remote-endpoint = <&dp_in>;
>> +				};
>> +			};
>> +		};
>> +
>> +		panel@0 {
>> +			reg = <0>;
> 
> Drop the @0 and reg as you only have 1.

Ditto.

Thanks,
Inki Dae

> 
>> +			...
>> +			port {
>> +				dp_in: endpoint {
>> +					remote-endpoint = <&dp_out>;
>>  				};
>>  			};
>>  		};
>> -- 
>> 1.9.1
>>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
index 64693f2..15b52cb 100644
--- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
@@ -66,8 +66,15 @@  Optional properties for dp-controller:
 		Hotplug detect GPIO.
 			Indicates which GPIO should be used for hotplug
 			detection
-	-video interfaces: Device node can contain video interface port
-			    nodes according to [1].
+Video interfaces:
+  Device node can contain video interface port nodes according to [1].
+  The following are properties specific to those nodes:
+
+  endpoint node connected to bridge or panel node:
+   - remote-endpoint: specifies the endpoint in panel or bridge node.
+		      This node is required in all kinds of exynos dp
+		      to represent the connection between dp and bridge
+		      ,or dp and panel.
 
 [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
 
@@ -111,9 +118,22 @@  Board Specific portion:
 		};
 
 		ports {
-			port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port {
 				dp_out: endpoint {
-					remote-endpoint = <&bridge_in>;
+					remote-endpoint = <&dp_in>;
+				};
+			};
+		};
+
+		panel@0 {
+			reg = <0>;
+			...
+			port {
+				dp_in: endpoint {
+					remote-endpoint = <&dp_out>;
 				};
 			};
 		};