Message ID | 1450103575-10066-1-git-send-email-linus.walleij@linaro.org (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Mon, Dec 14, 2015 at 03:32:55PM +0100, Linus Walleij wrote: > This adds a device tree for the CloudEngines PogoPlug series 4 > NAS device. Inspired by out-of-tree boardfiles from ArchLinux > by Kevin Mihelich. > > Cc: Moonman <moonman.ca@gmail.com> > Cc: Kevin Mihelich <kevin@archlinuxarm.org> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Thanks Andrew > --- > ChangeLog v2->v3: > - Drop current-speed = <115200> from the uart > ChangeLog v1->v2: > - Use <dt-bindings/input/linux-event-codes.h> > - Specify default baud rate etc differently > - Rename LEDs "pogoplugv4*" > - Skip registering i2c0 as there is nothing on it > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++ > 2 files changed, 179 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 30bbc3746130..2d9f475a9ceb 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ > kirkwood-openrd-client.dtb \ > kirkwood-openrd-ultimate.dtb \ > kirkwood-pogo_e02.dtb \ > + kirkwood-pogoplug-series-4.dtb \ > kirkwood-rd88f6192.dtb \ > kirkwood-rd88f6281-z0.dtb \ > kirkwood-rd88f6281-a.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts > new file mode 100644 > index 000000000000..1db6f2c506cc > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts > @@ -0,0 +1,178 @@ > +/* > + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4 > + * inspired by the board files made by Kevin Mihelich for ArchLinux, > + * and their DTS file. > + * > + * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org> > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6192.dtsi" > +#include <dt-bindings/input/linux-event-codes.h> > + > +/ { > + model = "Cloud Engines PogoPlug Series 4"; > + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x08000000>; > + }; > + > + chosen { > + stdout-path = "uart0:115200n8"; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_button_eject>; > + pinctrl-names = "default"; > + > + button@1 { > + debounce_interval = <50>; > + wakeup-source; > + linux,code = <KEY_EJECTCD>; > + label = "Eject Button"; > + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_led_green &pmx_led_red>; > + pinctrl-names = "default"; > + > + health { > + label = "pogoplugv4:green:health"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + fault { > + label = "pogoplugv4:red:fault"; > + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; > + > +&pinctrl { > + pmx_sata0: pmx-sata0 { > + marvell,pins = "mpp21"; > + marvell,function = "sata0"; > + }; > + > + pmx_sata1: pmx-sata1 { > + marvell,pins = "mpp20"; > + marvell,function = "sata1"; > + }; > + > + pmx_sdio_cd: pmx-sdio-cd { > + marvell,pins = "mpp27"; > + marvell,function = "gpio"; > + }; > + > + pmx_sdio_wp: pmx-sdio-wp { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + > + pmx_button_eject: pmx-button-eject { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_green: pmx-led-green { > + marvell,pins = "mpp22"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_red: pmx-led-red { > + marvell,pins = "mpp24"; > + marvell,function = "gpio"; > + }; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +/* > + * This PCIE controller has a USB 3.0 XHCI controller at 1,0 > + */ > +&pciec { > + status = "okay"; > +}; > + > +&pcie0 { > + status = "okay"; > +}; > + > +&sata { > + status = "okay"; > + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; > + pinctrl-names = "default"; > + nr-ports = <1>; > +}; > + > +&sdio { > + status = "okay"; > + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>; > + pinctrl-names = "default"; > + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; > +}; > + > +&nand { > + /* 128 MiB of NAND flash */ > + chip-delay = <40>; > + status = "okay"; > + partitions { > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x00000000 0x200000>; > + read-only; > + }; > + > + partition@200000 { > + label = "uImage"; > + reg = <0x00200000 0x300000>; > + }; > + > + partition@500000 { > + label = "uImage2"; > + reg = <0x00500000 0x300000>; > + }; > + > + partition@800000 { > + label = "failsafe"; > + reg = <0x00800000 0x800000>; > + }; > + > + partition@1000000 { > + label = "root"; > + reg = <0x01000000 0x7000000>; > + }; > + }; > +}; > + > +&mdio { > + status = "okay"; > + > + ethphy0: ethernet-phy@0 { > + reg = <0>; > + }; > +}; > + > +ð0 { > + status = "okay"; > + ethernet0-port@0 { > + phy-handle = <ðphy0>; > + }; > +}; > -- > 2.4.3 >
Hi Linus, On lun., déc. 14 2015, Andrew Lunn <andrew@lunn.ch> wrote: > On Mon, Dec 14, 2015 at 03:32:55PM +0100, Linus Walleij wrote: >> This adds a device tree for the CloudEngines PogoPlug series 4 >> NAS device. Inspired by out-of-tree boardfiles from ArchLinux >> by Kevin Mihelich. >> >> Cc: Moonman <moonman.ca@gmail.com> >> Cc: Kevin Mihelich <kevin@archlinuxarm.org> >> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > > Acked-by: Andrew Lunn <andrew@lunn.ch> Applied on mvebu/dt Thanks, Gregory > > Thanks > Andrew > >> --- >> ChangeLog v2->v3: >> - Drop current-speed = <115200> from the uart >> ChangeLog v1->v2: >> - Use <dt-bindings/input/linux-event-codes.h> >> - Specify default baud rate etc differently >> - Rename LEDs "pogoplugv4*" >> - Skip registering i2c0 as there is nothing on it >> --- >> arch/arm/boot/dts/Makefile | 1 + >> arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++ >> 2 files changed, 179 insertions(+) >> create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts >> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >> index 30bbc3746130..2d9f475a9ceb 100644 >> --- a/arch/arm/boot/dts/Makefile >> +++ b/arch/arm/boot/dts/Makefile >> @@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ >> kirkwood-openrd-client.dtb \ >> kirkwood-openrd-ultimate.dtb \ >> kirkwood-pogo_e02.dtb \ >> + kirkwood-pogoplug-series-4.dtb \ >> kirkwood-rd88f6192.dtb \ >> kirkwood-rd88f6281-z0.dtb \ >> kirkwood-rd88f6281-a.dtb \ >> diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts >> new file mode 100644 >> index 000000000000..1db6f2c506cc >> --- /dev/null >> +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts >> @@ -0,0 +1,178 @@ >> +/* >> + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4 >> + * inspired by the board files made by Kevin Mihelich for ArchLinux, >> + * and their DTS file. >> + * >> + * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org> >> + */ >> + >> +/dts-v1/; >> + >> +#include "kirkwood.dtsi" >> +#include "kirkwood-6192.dtsi" >> +#include <dt-bindings/input/linux-event-codes.h> >> + >> +/ { >> + model = "Cloud Engines PogoPlug Series 4"; >> + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", >> + "marvell,kirkwood"; >> + >> + memory { >> + device_type = "memory"; >> + reg = <0x00000000 0x08000000>; >> + }; >> + >> + chosen { >> + stdout-path = "uart0:115200n8"; >> + }; >> + >> + gpio_keys { >> + compatible = "gpio-keys"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + pinctrl-0 = <&pmx_button_eject>; >> + pinctrl-names = "default"; >> + >> + button@1 { >> + debounce_interval = <50>; >> + wakeup-source; >> + linux,code = <KEY_EJECTCD>; >> + label = "Eject Button"; >> + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; >> + }; >> + }; >> + >> + gpio-leds { >> + compatible = "gpio-leds"; >> + pinctrl-0 = <&pmx_led_green &pmx_led_red>; >> + pinctrl-names = "default"; >> + >> + health { >> + label = "pogoplugv4:green:health"; >> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; >> + default-state = "on"; >> + }; >> + fault { >> + label = "pogoplugv4:red:fault"; >> + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; >> + }; >> + }; >> +}; >> + >> +&pinctrl { >> + pmx_sata0: pmx-sata0 { >> + marvell,pins = "mpp21"; >> + marvell,function = "sata0"; >> + }; >> + >> + pmx_sata1: pmx-sata1 { >> + marvell,pins = "mpp20"; >> + marvell,function = "sata1"; >> + }; >> + >> + pmx_sdio_cd: pmx-sdio-cd { >> + marvell,pins = "mpp27"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_sdio_wp: pmx-sdio-wp { >> + marvell,pins = "mpp28"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_button_eject: pmx-button-eject { >> + marvell,pins = "mpp29"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_green: pmx-led-green { >> + marvell,pins = "mpp22"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_red: pmx-led-red { >> + marvell,pins = "mpp24"; >> + marvell,function = "gpio"; >> + }; >> +}; >> + >> +&uart0 { >> + status = "okay"; >> +}; >> + >> +/* >> + * This PCIE controller has a USB 3.0 XHCI controller at 1,0 >> + */ >> +&pciec { >> + status = "okay"; >> +}; >> + >> +&pcie0 { >> + status = "okay"; >> +}; >> + >> +&sata { >> + status = "okay"; >> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; >> + pinctrl-names = "default"; >> + nr-ports = <1>; >> +}; >> + >> +&sdio { >> + status = "okay"; >> + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>; >> + pinctrl-names = "default"; >> + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; >> + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; >> +}; >> + >> +&nand { >> + /* 128 MiB of NAND flash */ >> + chip-delay = <40>; >> + status = "okay"; >> + partitions { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + partition@0 { >> + label = "u-boot"; >> + reg = <0x00000000 0x200000>; >> + read-only; >> + }; >> + >> + partition@200000 { >> + label = "uImage"; >> + reg = <0x00200000 0x300000>; >> + }; >> + >> + partition@500000 { >> + label = "uImage2"; >> + reg = <0x00500000 0x300000>; >> + }; >> + >> + partition@800000 { >> + label = "failsafe"; >> + reg = <0x00800000 0x800000>; >> + }; >> + >> + partition@1000000 { >> + label = "root"; >> + reg = <0x01000000 0x7000000>; >> + }; >> + }; >> +}; >> + >> +&mdio { >> + status = "okay"; >> + >> + ethphy0: ethernet-phy@0 { >> + reg = <0>; >> + }; >> +}; >> + >> +ð0 { >> + status = "okay"; >> + ethernet0-port@0 { >> + phy-handle = <ðphy0>; >> + }; >> +}; >> -- >> 2.4.3 >>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 30bbc3746130..2d9f475a9ceb 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-openrd-client.dtb \ kirkwood-openrd-ultimate.dtb \ kirkwood-pogo_e02.dtb \ + kirkwood-pogoplug-series-4.dtb \ kirkwood-rd88f6192.dtb \ kirkwood-rd88f6281-z0.dtb \ kirkwood-rd88f6281-a.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts new file mode 100644 index 000000000000..1db6f2c506cc --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts @@ -0,0 +1,178 @@ +/* + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4 + * inspired by the board files made by Kevin Mihelich for ArchLinux, + * and their DTS file. + * + * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org> + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6192.dtsi" +#include <dt-bindings/input/linux-event-codes.h> + +/ { + model = "Cloud Engines PogoPlug Series 4"; + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; + }; + + chosen { + stdout-path = "uart0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_button_eject>; + pinctrl-names = "default"; + + button@1 { + debounce_interval = <50>; + wakeup-source; + linux,code = <KEY_EJECTCD>; + label = "Eject Button"; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_led_green &pmx_led_red>; + pinctrl-names = "default"; + + health { + label = "pogoplugv4:green:health"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + fault { + label = "pogoplugv4:red:fault"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pinctrl { + pmx_sata0: pmx-sata0 { + marvell,pins = "mpp21"; + marvell,function = "sata0"; + }; + + pmx_sata1: pmx-sata1 { + marvell,pins = "mpp20"; + marvell,function = "sata1"; + }; + + pmx_sdio_cd: pmx-sdio-cd { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_sdio_wp: pmx-sdio-wp { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_button_eject: pmx-button-eject { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_green: pmx-led-green { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_led_red: pmx-led-red { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; +}; + +&uart0 { + status = "okay"; +}; + +/* + * This PCIE controller has a USB 3.0 XHCI controller at 1,0 + */ +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&sata { + status = "okay"; + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + nr-ports = <1>; +}; + +&sdio { + status = "okay"; + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>; + pinctrl-names = "default"; + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; +}; + +&nand { + /* 128 MiB of NAND flash */ + chip-delay = <40>; + status = "okay"; + partitions { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x200000>; + read-only; + }; + + partition@200000 { + label = "uImage"; + reg = <0x00200000 0x300000>; + }; + + partition@500000 { + label = "uImage2"; + reg = <0x00500000 0x300000>; + }; + + partition@800000 { + label = "failsafe"; + reg = <0x00800000 0x800000>; + }; + + partition@1000000 { + label = "root"; + reg = <0x01000000 0x7000000>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +};
This adds a device tree for the CloudEngines PogoPlug series 4 NAS device. Inspired by out-of-tree boardfiles from ArchLinux by Kevin Mihelich. Cc: Moonman <moonman.ca@gmail.com> Cc: Kevin Mihelich <kevin@archlinuxarm.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v2->v3: - Drop current-speed = <115200> from the uart ChangeLog v1->v2: - Use <dt-bindings/input/linux-event-codes.h> - Specify default baud rate etc differently - Rename LEDs "pogoplugv4*" - Skip registering i2c0 as there is nothing on it --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts