@@ -1854,6 +1854,33 @@ struct cfg80211_ibss_params {
};
/**
+ * struct cfg80211_bss_select_adjust - BSS selection with RSSI adjustment.
+ *
+ * @band: band of BSS which should match for RSSI level adjustment.
+ * @delta: value of RSSI level adjustment.
+ */
+struct cfg80211_bss_select_adjust {
+ enum nl80211_band band;
+ s8 delta;
+};
+
+/**
+ * struct cfg80211_bss_selection - connection parameters for BSS selection.
+ *
+ * @behaviour: requested BSS selection behaviour.
+ * @param: parameters for requestion behaviour.
+ * @band_pref: preferred band for %NL80211_BSS_SELECT_ATTR_BAND_PREF.
+ * @adjust: parameters for %NL80211_BSS_SELECT_ATTR_RSSI_ADJUST.
+ */
+struct cfg80211_bss_selection {
+ enum nl80211_bss_select_attr behaviour;
+ union {
+ enum nl80211_band band_pref;
+ struct cfg80211_bss_select_adjust adjust;
+ } param;
+};
+
+/**
* struct cfg80211_connect_params - Connection parameters
*
* This structure provides information needed to complete IEEE 802.11
@@ -1888,6 +1915,7 @@ struct cfg80211_ibss_params {
* @ht_capa_mask: The bits of ht_capa which are to be used.
* @vht_capa: VHT Capability overrides
* @vht_capa_mask: The bits of vht_capa which are to be used.
+ * @bss_select: criteria to be used for BSS selection.
*/
struct cfg80211_connect_params {
struct ieee80211_channel *channel;
@@ -1910,6 +1938,7 @@ struct cfg80211_connect_params {
struct ieee80211_ht_cap ht_capa_mask;
struct ieee80211_vht_cap vht_capa;
struct ieee80211_vht_cap vht_capa_mask;
+ struct cfg80211_bss_selection bss_select;
};
/**
@@ -3178,6 +3207,9 @@ struct wiphy_vendor_command {
* low rssi when a frame is heard on different channel, then it should set
* this variable to the maximal offset for which it can compensate.
* This value should be set in MHz.
+ * @bss_select_support: bitmask indicating the BSS selection criteria supported
+ * by the driver in the .connect() callback. The bit position maps to the
+ * attribute indices defined in &enum nl80211_bss_select_attr.
*/
struct wiphy {
/* assign these fields before you register the wiphy */
@@ -3300,6 +3332,8 @@ struct wiphy {
u8 max_num_csa_counters;
u8 max_adj_channel_rssi_comp;
+ u32 bss_select_support;
+
char priv[0] __aligned(NETDEV_ALIGN);
};
@@ -1789,6 +1789,12 @@ enum nl80211_commands {
* thus it must not specify the number of iterations, only the interval
* between scans. The scan plans are executed sequentially.
* Each scan plan is a nested attribute of &enum nl80211_sched_scan_plan.
+ * @NL80211_ATTR_BSS_SELECT: nested attribute for driver supporting the
+ * BSS selection feature. When used with %NL80211_CMD_GET_WIPHY it contains
+ * NLA_FLAG type according &enum nl80211_bss_select_attr to indicate what
+ * BSS selection behaviours are supported. When used with %NL80211_CMD_CONNECT
+ * it contains the behaviour and parameters for BSS selection to be done by
+ * driver and/or firmware.
*
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
@@ -2164,6 +2170,8 @@ enum nl80211_attrs {
NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS,
NL80211_ATTR_SCHED_SCAN_PLANS,
+ NL80211_ATTR_BSS_SELECT,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -4651,4 +4659,38 @@ enum nl80211_sched_scan_plan {
__NL80211_SCHED_SCAN_PLAN_AFTER_LAST - 1
};
+/**
+ * enum nl80211_bss_select_attr - attributes for bss selection.
+ *
+ * @__NL80211_BSS_SELECT_ATTR_INVALID: reserved.
+ * @NL80211_BSS_SELECT_ATTR_RSSI: Flag indicating only RSSI-based BSS selection
+ * is requested.
+ * @NL80211_BSS_SELECT_ATTR_BAND_PREF: attribute indicating BSS
+ * selection should be done such that the specified band is preferred.
+ * When there are multiple BSS-es in the preferred band, the driver
+ * shall use RSSI-based BSS selection as a second step. The value of
+ * this attribute is according to &enum nl80211_band (u32).
+ * @NL80211_BSS_SELECT_ATTR_RSSI_ADJUST: When present the RSSI level for
+ * BSS-es in the specified band is to be adjusted before doing
+ * RSSI-based BSS selection. The attribute value is a packed two-byte
+ * value. The lower byte contains the adjustment value (s8) and the
+ * high byte contains the band according &enum nl80211_band.
+ * @NL80211_BSS_SELECT_ATTR_MAX: highest bss select attribute number.
+ *@__NL80211_BSS_SELECT_ATTR_AFTER_LAST: internal use.
+ *
+ * These attributes are found within %NL80211_ATTR_BSS_SELECT and
+ * indicate the required BSS selection behaviour which the driver
+ * should use.
+ */
+enum nl80211_bss_select_attr {
+ __NL80211_BSS_SELECT_ATTR_INVALID,
+ NL80211_BSS_SELECT_ATTR_RSSI,
+ NL80211_BSS_SELECT_ATTR_BAND_PREF,
+ NL80211_BSS_SELECT_ATTR_RSSI_ADJUST,
+
+ /* keep last */
+ __NL80211_BSS_SELECT_ATTR_AFTER_LAST,
+ NL80211_BSS_SELECT_ATTR_MAX = __NL80211_BSS_SELECT_ATTR_AFTER_LAST - 1
+};
+
#endif /* __LINUX_NL80211_H */
@@ -626,6 +626,10 @@ int wiphy_register(struct wiphy *wiphy)
!rdev->ops->set_mac_acl)))
return -EINVAL;
+ if (WARN_ON(wiphy->bss_select_support &&
+ (wiphy->bss_select_support & ~(BIT(NL80211_BSS_SELECT_ATTR_MAX) - 1))))
+ return -EINVAL;
+
if (wiphy->addresses)
memcpy(wiphy->perm_addr, wiphy->addresses[0].addr, ETH_ALEN);
@@ -485,6 +485,13 @@ nl80211_plan_policy[NL80211_SCHED_SCAN_PLAN_MAX + 1] = {
[NL80211_SCHED_SCAN_PLAN_ITERATIONS] = { .type = NLA_U32 },
};
+static const struct nla_policy
+nl80211_bss_select_policy[NL80211_BSS_SELECT_ATTR_MAX + 1] = {
+ [NL80211_BSS_SELECT_ATTR_RSSI] = { .type = NLA_FLAG },
+ [NL80211_BSS_SELECT_ATTR_BAND_PREF] = { .type = NLA_U32 },
+ [NL80211_BSS_SELECT_ATTR_RSSI_ADJUST] = { .type = NLA_U8 },
+};
+
static int nl80211_prepare_wdev_dump(struct sk_buff *skb,
struct netlink_callback *cb,
struct cfg80211_registered_device **rdev,
@@ -1730,6 +1737,24 @@ static int nl80211_send_wiphy(struct cfg80211_registered_device *rdev,
rdev->wiphy.ext_features))
goto nla_put_failure;
+ if (rdev->wiphy.bss_select_support) {
+ struct nlattr *nested;
+ u32 bss_select_support = rdev->wiphy.bss_select_support;
+
+ nested = nla_nest_start(msg, NL80211_ATTR_BSS_SELECT);
+ if (!nested)
+ goto nla_put_failure;
+
+ i = 0;
+ while (bss_select_support) {
+ if ((bss_select_support & 1) &&
+ nla_put_flag(msg, i))
+ goto nla_put_failure;
+ i++;
+ bss_select_support >>= 1;
+ }
+ nla_nest_end(msg, nested);
+ }
/* done */
state->split_start = 0;
break;
@@ -5753,6 +5778,42 @@ static int validate_scan_freqs(struct nlattr *freqs)
return n_channels;
}
+static int parse_bss_select(struct nlattr *nla,
+ struct cfg80211_bss_selection *bss_select)
+{
+ struct nlattr *attr[NL80211_BSS_SELECT_ATTR_MAX + 1];
+ u16 band_delta;
+ int err;
+
+ err = nla_parse(attr, NL80211_BSS_SELECT_ATTR_MAX,
+ nla_data(nla), nla_len(nla), nl80211_bss_select_policy);
+ if (err)
+ return err;
+
+ bss_select->behaviour = __NL80211_BSS_SELECT_ATTR_INVALID;
+
+ if (attr[NL80211_BSS_SELECT_ATTR_RSSI])
+ bss_select->behaviour = NL80211_BSS_SELECT_ATTR_RSSI;
+
+ if (attr[NL80211_BSS_SELECT_ATTR_BAND_PREF]) {
+ bss_select->behaviour = NL80211_BSS_SELECT_ATTR_BAND_PREF;
+ bss_select->param.band_pref =
+ nla_get_u32(attr[NL80211_BSS_SELECT_ATTR_BAND_PREF]);
+ }
+ if (attr[NL80211_BSS_SELECT_ATTR_RSSI_ADJUST]) {
+ bss_select->behaviour = NL80211_BSS_SELECT_ATTR_RSSI_ADJUST;
+ band_delta =
+ nla_get_u16(attr[NL80211_BSS_SELECT_ATTR_RSSI_ADJUST]);
+ bss_select->param.adjust.delta = (s8)(band_delta & 0xFF);
+ bss_select->param.adjust.band = band_delta >> 8;
+ }
+
+ if (bss_select->behaviour == __NL80211_BSS_SELECT_ATTR_INVALID)
+ return -EINVAL;
+
+ return 0;
+}
+
static int nl80211_parse_random_mac(struct nlattr **attrs,
u8 *mac_addr, u8 *mac_addr_mask)
{
@@ -7980,6 +8041,21 @@ static int nl80211_connect(struct sk_buff *skb, struct genl_info *info)
connect.flags |= ASSOC_REQ_USE_RRM;
}
+ /* only do bss selection when no BSSID is specified. */
+ if (!connect.bssid && rdev->wiphy.bss_select_support &&
+ info->attrs[NL80211_ATTR_BSS_SELECT]) {
+ err = parse_bss_select(info->attrs[NL80211_ATTR_BSS_SELECT],
+ &connect.bss_select);
+ if (err) {
+ kzfree(connkeys);
+ return err;
+ }
+ if (!(rdev->wiphy.bss_select_support & BIT(connect.bss_select.behaviour))) {
+ kzfree(connkeys);
+ return -EINVAL;
+ }
+ }
+
wdev_lock(dev->ieee80211_ptr);
err = cfg80211_connect(rdev, dev, &connect, connkeys, NULL);
wdev_unlock(dev->ieee80211_ptr);