Message ID | 1464819199-19292-1-git-send-email-matthew.d.roper@intel.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Wed, Jun 01, 2016 at 03:13:19PM -0700, Matt Roper wrote: > Gen9 has two scalers on pipes A & B, but only a single scaler on pipe C. > We should bail out of the test early on pipe C so that we don't ask the > kernel to use more scalers than we really have. > > Note that this test may still fail (on any pipe) if we're already using > one of the scalers as a panel fitter. But at least this is an > improvement over the existing state where the test is guaranteed to fail > if run with pipe C active. > > Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92248 > Signed-off-by: Matt Roper <matthew.d.roper@intel.com> > --- > tests/kms_plane_scaling.c | 7 ++++++- > 1 file changed, 6 insertions(+), 1 deletion(-) > > diff --git a/tests/kms_plane_scaling.c b/tests/kms_plane_scaling.c > index ad5404d..2b17702 100644 > --- a/tests/kms_plane_scaling.c > +++ b/tests/kms_plane_scaling.c > @@ -264,6 +264,9 @@ static void test_plane_scaling(data_t *d) > igt_display_commit2(display, COMMIT_UNIVERSAL); > } > > + if (pipe == PIPE_C) > + goto crtcdone; > + You you make assumptions like that, then you should probably make the test skip on !gen9. The test is making a lot of assumptions already though, so probably would blow up on many other platforms anyway. It also makes some assumptions about display resolutions and whatnot, so might blow up on gen9 as well. Would be cool if someone could make this use CRCs as well, but that would probably be a little difficult since the hardware scaling algorithm is naturally undocumented :( How I long for the old video overlay... Hmm. Actually there does seem to be a way to force bilinear scaling at least. Matching that with software rendering might be doable. > /* Set up fb3->plane3 mapping. */ > d->plane3 = igt_output_get_plane(output, IGT_PLANE_3); > igt_plane_set_fb(d->plane3, &d->fb3); > @@ -301,9 +304,11 @@ static void test_plane_scaling(data_t *d) > igt_display_commit2(display, COMMIT_UNIVERSAL); > } > > +crtcdone: > /* back to single plane mode */ > igt_plane_set_fb(d->plane2, NULL); > - igt_plane_set_fb(d->plane3, NULL); > + if (pipe != PIPE_C) > + igt_plane_set_fb(d->plane3, NULL); > igt_display_commit2(display, COMMIT_UNIVERSAL); > > valid_tests++; > -- > 2.1.4 > > _______________________________________________ > Intel-gfx mailing list > Intel-gfx@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
On Thu, Jun 02, 2016 at 11:35:08AM +0300, Ville Syrjälä wrote: > On Wed, Jun 01, 2016 at 03:13:19PM -0700, Matt Roper wrote: > > Gen9 has two scalers on pipes A & B, but only a single scaler on pipe C. > > We should bail out of the test early on pipe C so that we don't ask the > > kernel to use more scalers than we really have. > > > > Note that this test may still fail (on any pipe) if we're already using > > one of the scalers as a panel fitter. But at least this is an > > improvement over the existing state where the test is guaranteed to fail > > if run with pipe C active. > > > > Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92248 > > Signed-off-by: Matt Roper <matthew.d.roper@intel.com> > > --- > > tests/kms_plane_scaling.c | 7 ++++++- > > 1 file changed, 6 insertions(+), 1 deletion(-) > > > > diff --git a/tests/kms_plane_scaling.c b/tests/kms_plane_scaling.c > > index ad5404d..2b17702 100644 > > --- a/tests/kms_plane_scaling.c > > +++ b/tests/kms_plane_scaling.c > > @@ -264,6 +264,9 @@ static void test_plane_scaling(data_t *d) > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > } > > > > + if (pipe == PIPE_C) > > + goto crtcdone; > > + > > You you make assumptions like that, then you should probably make the > test skip on !gen9. It already does as far as I can see. It sets data.num_scalers to 0 for pre-gen9 in the main function and then has a igt_require(d->num_scalers) in the test function. > The test is making a lot of assumptions already though, so probably > would blow up on many other platforms anyway. It also makes some > assumptions about display resolutions and whatnot, so might blow up on > gen9 as well. Yep, agreed with this. I think there's a lot of improvement that could be done here, but at the moment I just wanted to fix one case of low hanging fruit that would fail 100% of the time. Matt > > Would be cool if someone could make this use CRCs as well, but that > would probably be a little difficult since the hardware scaling > algorithm is naturally undocumented :( How I long for the old video > overlay... Hmm. Actually there does seem to be a way to force bilinear > scaling at least. Matching that with software rendering might be doable. > > > /* Set up fb3->plane3 mapping. */ > > d->plane3 = igt_output_get_plane(output, IGT_PLANE_3); > > igt_plane_set_fb(d->plane3, &d->fb3); > > @@ -301,9 +304,11 @@ static void test_plane_scaling(data_t *d) > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > } > > > > +crtcdone: > > /* back to single plane mode */ > > igt_plane_set_fb(d->plane2, NULL); > > - igt_plane_set_fb(d->plane3, NULL); > > + if (pipe != PIPE_C) > > + igt_plane_set_fb(d->plane3, NULL); > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > > > valid_tests++; > > -- > > 2.1.4 > > > > _______________________________________________ > > Intel-gfx mailing list > > Intel-gfx@lists.freedesktop.org > > https://lists.freedesktop.org/mailman/listinfo/intel-gfx > > -- > Ville Syrjälä > Intel OTC
On Thu, Jun 02, 2016 at 07:50:33AM -0700, Matt Roper wrote: > On Thu, Jun 02, 2016 at 11:35:08AM +0300, Ville Syrjälä wrote: > > On Wed, Jun 01, 2016 at 03:13:19PM -0700, Matt Roper wrote: > > > Gen9 has two scalers on pipes A & B, but only a single scaler on pipe C. > > > We should bail out of the test early on pipe C so that we don't ask the > > > kernel to use more scalers than we really have. > > > > > > Note that this test may still fail (on any pipe) if we're already using > > > one of the scalers as a panel fitter. But at least this is an > > > improvement over the existing state where the test is guaranteed to fail > > > if run with pipe C active. > > > > > > Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92248 > > > Signed-off-by: Matt Roper <matthew.d.roper@intel.com> > > > --- > > > tests/kms_plane_scaling.c | 7 ++++++- > > > 1 file changed, 6 insertions(+), 1 deletion(-) > > > > > > diff --git a/tests/kms_plane_scaling.c b/tests/kms_plane_scaling.c > > > index ad5404d..2b17702 100644 > > > --- a/tests/kms_plane_scaling.c > > > +++ b/tests/kms_plane_scaling.c > > > @@ -264,6 +264,9 @@ static void test_plane_scaling(data_t *d) > > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > > } > > > > > > + if (pipe == PIPE_C) > > > + goto crtcdone; > > > + > > > > You you make assumptions like that, then you should probably make the > > test skip on !gen9. > > It already does as far as I can see. It sets data.num_scalers to 0 for > pre-gen9 in the main function and then has a > igt_require(d->num_scalers) in the test function. Hmm. Seems like a rather roundabout way of writing "I want gen9". > > > The test is making a lot of assumptions already though, so probably > > would blow up on many other platforms anyway. It also makes some > > assumptions about display resolutions and whatnot, so might blow up on > > gen9 as well. > > Yep, agreed with this. I think there's a lot of improvement that could > be done here, but at the moment I just wanted to fix one case of low > hanging fruit that would fail 100% of the time. > > > Matt > > > > > Would be cool if someone could make this use CRCs as well, but that > > would probably be a little difficult since the hardware scaling > > algorithm is naturally undocumented :( How I long for the old video > > overlay... Hmm. Actually there does seem to be a way to force bilinear > > scaling at least. Matching that with software rendering might be doable. > > > > > /* Set up fb3->plane3 mapping. */ > > > d->plane3 = igt_output_get_plane(output, IGT_PLANE_3); > > > igt_plane_set_fb(d->plane3, &d->fb3); > > > @@ -301,9 +304,11 @@ static void test_plane_scaling(data_t *d) > > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > > } > > > > > > +crtcdone: > > > /* back to single plane mode */ > > > igt_plane_set_fb(d->plane2, NULL); > > > - igt_plane_set_fb(d->plane3, NULL); > > > + if (pipe != PIPE_C) > > > + igt_plane_set_fb(d->plane3, NULL); > > > igt_display_commit2(display, COMMIT_UNIVERSAL); > > > > > > valid_tests++; > > > -- > > > 2.1.4 > > > > > > _______________________________________________ > > > Intel-gfx mailing list > > > Intel-gfx@lists.freedesktop.org > > > https://lists.freedesktop.org/mailman/listinfo/intel-gfx > > > > -- > > Ville Syrjälä > > Intel OTC > > -- > Matt Roper > Graphics Software Engineer > IoTG Platform Enabling & Development > Intel Corporation > (916) 356-2795
diff --git a/tests/kms_plane_scaling.c b/tests/kms_plane_scaling.c index ad5404d..2b17702 100644 --- a/tests/kms_plane_scaling.c +++ b/tests/kms_plane_scaling.c @@ -264,6 +264,9 @@ static void test_plane_scaling(data_t *d) igt_display_commit2(display, COMMIT_UNIVERSAL); } + if (pipe == PIPE_C) + goto crtcdone; + /* Set up fb3->plane3 mapping. */ d->plane3 = igt_output_get_plane(output, IGT_PLANE_3); igt_plane_set_fb(d->plane3, &d->fb3); @@ -301,9 +304,11 @@ static void test_plane_scaling(data_t *d) igt_display_commit2(display, COMMIT_UNIVERSAL); } +crtcdone: /* back to single plane mode */ igt_plane_set_fb(d->plane2, NULL); - igt_plane_set_fb(d->plane3, NULL); + if (pipe != PIPE_C) + igt_plane_set_fb(d->plane3, NULL); igt_display_commit2(display, COMMIT_UNIVERSAL); valid_tests++;
Gen9 has two scalers on pipes A & B, but only a single scaler on pipe C. We should bail out of the test early on pipe C so that we don't ask the kernel to use more scalers than we really have. Note that this test may still fail (on any pipe) if we're already using one of the scalers as a panel fitter. But at least this is an improvement over the existing state where the test is guaranteed to fail if run with pipe C active. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92248 Signed-off-by: Matt Roper <matthew.d.roper@intel.com> --- tests/kms_plane_scaling.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)