| Message ID | 1465373117-823-1-git-send-email-shawn.lin@rock-chips.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
On 08/06/16 09:05, Shawn Lin wrote: > This patch adds a binding that describes the Rockchip PCIe controller > found on Rockchip SoCs PCIe interface. > > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > > --- > > Changes in v2: > - fix lots clk/reset stuff suggested by Heiko > - remove msi-parent and add msi-map suggested by Marc > - drop phy related stuff > - some others minor fixes > > .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > new file mode 100644 > index 0000000..eb92e29 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > @@ -0,0 +1,86 @@ > +* Rockchip AXI PCIe Root Port Bridge DT description > + > +Required properties: > +- #address-cells: Address representation for root ports, set to <3> > +- #size-cells: Size representation for root ports, set to <2> > +- #interrupt-cells: specifies the number of cells needed to encode an > + interrupt source. The value must be 1. > +- compatible: Should contain "rockchip,rk3399-pcie" > +- reg: Two register ranges as listed in the reg-names property > +- reg-names: Must include the following names > + - "axi-base" > + - "apb-base" > +- clocks: Must contain an entry for each entry in clock-names. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Must include the following entries: > + - "aclk" > + - "aclk-perf" > + - "hclk" > + - "pm" > +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. > +- phy-names: MUST be "pcie-phy". > +- interrupts: Three interrupt entries must be specified. > +- interrupt-names: Must include the following names > + - "sys" > + - "legacy" > + - "client" > +- resets: Must contain five entries for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names: Must include the following names > + - "core" > + - "mgmt" > + - "mgmt-sticky" > + - "pipe" > +- pinctrl-names : The pin control state names > +- pinctrl-0: The "default" pinctrl state > +- interrupt-map-mask and interrupt-map: standard PCI properties > +- interrupt-controller: identifies the node as an interrupt controller > + > +Optional Property: > +- ep-gpios: contain the entry for pre-reset gpio > +- num-lanes: number of lanes to use > +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. Please do not describe the behaviour of the driver here. Thanks, M.
On Wed, Jun 08, 2016 at 04:05:17PM +0800, Shawn Lin wrote: > This patch adds a binding that describes the Rockchip PCIe controller > found on Rockchip SoCs PCIe interface. > > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > > --- > > Changes in v2: > - fix lots clk/reset stuff suggested by Heiko > - remove msi-parent and add msi-map suggested by Marc > - drop phy related stuff > - some others minor fixes > > .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > new file mode 100644 > index 0000000..eb92e29 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > @@ -0,0 +1,86 @@ > +* Rockchip AXI PCIe Root Port Bridge DT description > + > +Required properties: > +- #address-cells: Address representation for root ports, set to <3> > +- #size-cells: Size representation for root ports, set to <2> > +- #interrupt-cells: specifies the number of cells needed to encode an > + interrupt source. The value must be 1. > +- compatible: Should contain "rockchip,rk3399-pcie" > +- reg: Two register ranges as listed in the reg-names property > +- reg-names: Must include the following names > + - "axi-base" > + - "apb-base" > +- clocks: Must contain an entry for each entry in clock-names. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Must include the following entries: > + - "aclk" > + - "aclk-perf" > + - "hclk" > + - "pm" > +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. > +- phy-names: MUST be "pcie-phy". phy-names is kind of pointless for 1 phy. > +- interrupts: Three interrupt entries must be specified. > +- interrupt-names: Must include the following names > + - "sys" > + - "legacy" > + - "client" > +- resets: Must contain five entries for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names: Must include the following names > + - "core" > + - "mgmt" > + - "mgmt-sticky" > + - "pipe" > +- pinctrl-names : The pin control state names > +- pinctrl-0: The "default" pinctrl state > +- interrupt-map-mask and interrupt-map: standard PCI properties > +- interrupt-controller: identifies the node as an interrupt controller > + > +Optional Property: > +- ep-gpios: contain the entry for pre-reset gpio > +- num-lanes: number of lanes to use > +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > + > +Example: > + > +pcie0: pcie@f8000000 { > + compatible = "rockchip,rk3399-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, > + <&cru PCLK_PCIE>; > + clock-names = "aclk", "aclk-perf", > + "hclk"; > + bus-range = <0x0 0x1>; > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names: "sys", "legacy", "client"; > + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; > + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; > + assigned-clock-rates = <100000000>; > + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; > + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 > + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; No 64-bit memory space? > + num-lanes = <4>; > + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; > + reg-name = "axi-base", "apb-base"; > + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, > + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; > + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; > + phys = <&pcie_phy>; > + phy-names = "pcie-phy"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie_clkreq>; > + #interrupt-cells = <1>; > + interrupt-controller; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie0 1>, > + <0 0 0 2 &pcie0 2>, > + <0 0 0 3 &pcie0 3>, > + <0 0 0 4 &pcie0 4>; > +}; > -- > 2.3.7 > > -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Shawn, On Wed, Jun 8, 2016 at 1:05 AM, Shawn Lin <shawn.lin@rock-chips.com> wrote: > +pcie0: pcie@f8000000 { > + compatible = "rockchip,rk3399-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, > + <&cru PCLK_PCIE>; > + clock-names = "aclk", "aclk-perf", > + "hclk"; Code also requires a "pm" clock. > + bus-range = <0x0 0x1>; > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names: "sys", "legacy", "client"; Shouldn't be ":", should be "=". > + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; > + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; > + assigned-clock-rates = <100000000>; > + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; > + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 > + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; nit: I don't thin it's common to have spaces before/after the ">" and "<". nit: Be consistent about 0 vs. 0x0 in ranges. > + num-lanes = <4>; > + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; > + reg-name = "axi-base", "apb-base"; Should be "reg-names" (with an "s") > + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, > + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; > + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; You have 5 resets but 4 reset names. That doesn't seem right. Code shows you only getting 4, so presumably you need to remove the SRST_PCIEPHY one. -Doug -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, 8 Jun 2016 16:05:17 +0800 Shawn Lin <shawn.lin@rock-chips.com> wrote: > This patch adds a binding that describes the Rockchip PCIe controller > found on Rockchip SoCs PCIe interface. > > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > > --- > > Changes in v2: > - fix lots clk/reset stuff suggested by Heiko > - remove msi-parent and add msi-map suggested by Marc I noticed this ^^^^ ... > - drop phy related stuff > - some others minor fixes > > .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > new file mode 100644 > index 0000000..eb92e29 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > @@ -0,0 +1,86 @@ > +* Rockchip AXI PCIe Root Port Bridge DT description > + > +Required properties: > +- #address-cells: Address representation for root ports, set to <3> > +- #size-cells: Size representation for root ports, set to <2> > +- #interrupt-cells: specifies the number of cells needed to encode an > + interrupt source. The value must be 1. > +- compatible: Should contain "rockchip,rk3399-pcie" > +- reg: Two register ranges as listed in the reg-names property > +- reg-names: Must include the following names > + - "axi-base" > + - "apb-base" > +- clocks: Must contain an entry for each entry in clock-names. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Must include the following entries: > + - "aclk" > + - "aclk-perf" > + - "hclk" > + - "pm" > +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. > +- phy-names: MUST be "pcie-phy". > +- interrupts: Three interrupt entries must be specified. > +- interrupt-names: Must include the following names > + - "sys" > + - "legacy" > + - "client" > +- resets: Must contain five entries for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names: Must include the following names > + - "core" > + - "mgmt" > + - "mgmt-sticky" > + - "pipe" > +- pinctrl-names : The pin control state names > +- pinctrl-0: The "default" pinctrl state > +- interrupt-map-mask and interrupt-map: standard PCI properties > +- interrupt-controller: identifies the node as an interrupt controller > + > +Optional Property: > +- ep-gpios: contain the entry for pre-reset gpio > +- num-lanes: number of lanes to use > +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > + > +Example: > + > +pcie0: pcie@f8000000 { > + compatible = "rockchip,rk3399-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, > + <&cru PCLK_PCIE>; > + clock-names = "aclk", "aclk-perf", > + "hclk"; > + bus-range = <0x0 0x1>; > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names: "sys", "legacy", "client"; > + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; > + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; > + assigned-clock-rates = <100000000>; > + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; > + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 > + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; > + num-lanes = <4>; > + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; > + reg-name = "axi-base", "apb-base"; > + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, > + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; > + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; > + phys = <&pcie_phy>; > + phy-names = "pcie-phy"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie_clkreq>; > + #interrupt-cells = <1>; > + interrupt-controller; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie0 1>, > + <0 0 0 2 &pcie0 2>, > + <0 0 0 3 &pcie0 3>, > + <0 0 0 4 &pcie0 4>; > +}; And yet I don't see anything related to msi-map in the binding or in the example. As Doug mentioned issues with MSIs being delivered, I wonder if the two are related... Thanks, M.
在 2016/6/10 12:01, Doug Anderson 写道: > Shawn, > > On Wed, Jun 8, 2016 at 1:05 AM, Shawn Lin <shawn.lin@rock-chips.com> wrote: >> +pcie0: pcie@f8000000 { >> + compatible = "rockchip,rk3399-pcie"; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, >> + <&cru PCLK_PCIE>; >> + clock-names = "aclk", "aclk-perf", >> + "hclk"; > > Code also requires a "pm" clock. > >> + bus-range = <0x0 0x1>; >> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names: "sys", "legacy", "client"; > > Shouldn't be ":", should be "=". > > >> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; >> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; >> + assigned-clock-rates = <100000000>; >> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; >> + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 >> + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; > > nit: I don't thin it's common to have spaces before/after the ">" and "<". > nit: Be consistent about 0 vs. 0x0 in ranges. > > >> + num-lanes = <4>; >> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; >> + reg-name = "axi-base", "apb-base"; > > Should be "reg-names" (with an "s") > > >> + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, >> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; >> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; > > You have 5 resets but 4 reset names. That doesn't seem right. Code > shows you only getting 4, so presumably you need to remove the > SRST_PCIEPHY one. Thanks for catching these above as I forgot to rework the this sample. > > > -Doug > > _______________________________________________ > Linux-rockchip mailing list > Linux-rockchip@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-rockchip >
On 2016/6/9 4:44, Rob Herring wrote: > On Wed, Jun 08, 2016 at 04:05:17PM +0800, Shawn Lin wrote: >> This patch adds a binding that describes the Rockchip PCIe controller >> found on Rockchip SoCs PCIe interface. >> >> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> >> >> --- >> >> Changes in v2: >> - fix lots clk/reset stuff suggested by Heiko >> - remove msi-parent and add msi-map suggested by Marc >> - drop phy related stuff >> - some others minor fixes >> >> .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ >> 1 file changed, 86 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> >> diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> new file mode 100644 >> index 0000000..eb92e29 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> @@ -0,0 +1,86 @@ >> +* Rockchip AXI PCIe Root Port Bridge DT description >> + >> +Required properties: >> +- #address-cells: Address representation for root ports, set to <3> >> +- #size-cells: Size representation for root ports, set to <2> >> +- #interrupt-cells: specifies the number of cells needed to encode an >> + interrupt source. The value must be 1. >> +- compatible: Should contain "rockchip,rk3399-pcie" >> +- reg: Two register ranges as listed in the reg-names property >> +- reg-names: Must include the following names >> + - "axi-base" >> + - "apb-base" >> +- clocks: Must contain an entry for each entry in clock-names. >> + See ../clocks/clock-bindings.txt for details. >> +- clock-names: Must include the following entries: >> + - "aclk" >> + - "aclk-perf" >> + - "hclk" >> + - "pm" >> +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. >> +- phy-names: MUST be "pcie-phy". > > phy-names is kind of pointless for 1 phy. ok, I will remove it. > >> +- interrupts: Three interrupt entries must be specified. >> +- interrupt-names: Must include the following names >> + - "sys" >> + - "legacy" >> + - "client" >> +- resets: Must contain five entries for each entry in reset-names. >> + See ../reset/reset.txt for details. >> +- reset-names: Must include the following names >> + - "core" >> + - "mgmt" >> + - "mgmt-sticky" >> + - "pipe" >> +- pinctrl-names : The pin control state names >> +- pinctrl-0: The "default" pinctrl state >> +- interrupt-map-mask and interrupt-map: standard PCI properties >> +- interrupt-controller: identifies the node as an interrupt controller >> + >> +Optional Property: >> +- ep-gpios: contain the entry for pre-reset gpio >> +- num-lanes: number of lanes to use >> +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> + >> +Example: >> + >> +pcie0: pcie@f8000000 { >> + compatible = "rockchip,rk3399-pcie"; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, >> + <&cru PCLK_PCIE>; >> + clock-names = "aclk", "aclk-perf", >> + "hclk"; >> + bus-range = <0x0 0x1>; >> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names: "sys", "legacy", "client"; >> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; >> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; >> + assigned-clock-rates = <100000000>; >> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; >> + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 >> + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; > > No 64-bit memory space? Will fix this example. Thanks for catching this:) > >> + num-lanes = <4>; >> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; >> + reg-name = "axi-base", "apb-base"; >> + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, >> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; >> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; >> + phys = <&pcie_phy>; >> + phy-names = "pcie-phy"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pcie_clkreq>; >> + #interrupt-cells = <1>; >> + interrupt-controller; >> + interrupt-map-mask = <0 0 0 7>; >> + interrupt-map = <0 0 0 1 &pcie0 1>, >> + <0 0 0 2 &pcie0 2>, >> + <0 0 0 3 &pcie0 3>, >> + <0 0 0 4 &pcie0 4>; >> +}; >> -- >> 2.3.7 >> >> > > _______________________________________________ > Linux-rockchip mailing list > Linux-rockchip@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-rockchip >
Marc, On Fri, Jun 10, 2016 at 12:32 AM, Marc Zyngier <marc.zyngier@arm.com> wrote: > On Wed, 8 Jun 2016 16:05:17 +0800 > Shawn Lin <shawn.lin@rock-chips.com> wrote: > >> This patch adds a binding that describes the Rockchip PCIe controller >> found on Rockchip SoCs PCIe interface. >> >> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> >> >> --- >> >> Changes in v2: >> - fix lots clk/reset stuff suggested by Heiko >> - remove msi-parent and add msi-map suggested by Marc > > I noticed this ^^^^ ... > >> - drop phy related stuff >> - some others minor fixes >> >> .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ >> 1 file changed, 86 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> >> diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> new file mode 100644 >> index 0000000..eb92e29 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt >> @@ -0,0 +1,86 @@ >> +* Rockchip AXI PCIe Root Port Bridge DT description >> + >> +Required properties: >> +- #address-cells: Address representation for root ports, set to <3> >> +- #size-cells: Size representation for root ports, set to <2> >> +- #interrupt-cells: specifies the number of cells needed to encode an >> + interrupt source. The value must be 1. >> +- compatible: Should contain "rockchip,rk3399-pcie" >> +- reg: Two register ranges as listed in the reg-names property >> +- reg-names: Must include the following names >> + - "axi-base" >> + - "apb-base" >> +- clocks: Must contain an entry for each entry in clock-names. >> + See ../clocks/clock-bindings.txt for details. >> +- clock-names: Must include the following entries: >> + - "aclk" >> + - "aclk-perf" >> + - "hclk" >> + - "pm" >> +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. >> +- phy-names: MUST be "pcie-phy". >> +- interrupts: Three interrupt entries must be specified. >> +- interrupt-names: Must include the following names >> + - "sys" >> + - "legacy" >> + - "client" >> +- resets: Must contain five entries for each entry in reset-names. >> + See ../reset/reset.txt for details. >> +- reset-names: Must include the following names >> + - "core" >> + - "mgmt" >> + - "mgmt-sticky" >> + - "pipe" >> +- pinctrl-names : The pin control state names >> +- pinctrl-0: The "default" pinctrl state >> +- interrupt-map-mask and interrupt-map: standard PCI properties >> +- interrupt-controller: identifies the node as an interrupt controller >> + >> +Optional Property: >> +- ep-gpios: contain the entry for pre-reset gpio >> +- num-lanes: number of lanes to use >> +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this >> + is specified we'll defer probe until we can find this regulator. >> + >> +Example: >> + >> +pcie0: pcie@f8000000 { >> + compatible = "rockchip,rk3399-pcie"; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, >> + <&cru PCLK_PCIE>; >> + clock-names = "aclk", "aclk-perf", >> + "hclk"; >> + bus-range = <0x0 0x1>; >> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names: "sys", "legacy", "client"; >> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; >> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; >> + assigned-clock-rates = <100000000>; >> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; >> + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 >> + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; >> + num-lanes = <4>; >> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; >> + reg-name = "axi-base", "apb-base"; >> + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, >> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; >> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; >> + phys = <&pcie_phy>; >> + phy-names = "pcie-phy"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pcie_clkreq>; >> + #interrupt-cells = <1>; >> + interrupt-controller; >> + interrupt-map-mask = <0 0 0 7>; >> + interrupt-map = <0 0 0 1 &pcie0 1>, >> + <0 0 0 2 &pcie0 2>, >> + <0 0 0 3 &pcie0 3>, >> + <0 0 0 4 &pcie0 4>; >> +}; > > > And yet I don't see anything related to msi-map in the binding or in > the example. As Doug mentioned issues with MSIs being delivered, I > wonder if the two are related... With Shawn's latest patches and following his latest example dts snippet (which includes the msi-map), things worked much better. :) Thank you for your help! -Doug -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt new file mode 100644 index 0000000..eb92e29 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -0,0 +1,86 @@ +* Rockchip AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "rockchip,rk3399-pcie" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "axi-base" + - "apb-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". +- interrupts: Three interrupt entries must be specified. +- interrupt-names: Must include the following names + - "sys" + - "legacy" + - "client" +- resets: Must contain five entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- interrupt-map-mask and interrupt-map: standard PCI properties +- interrupt-controller: identifies the node as an interrupt controller + +Optional Property: +- ep-gpios: contain the entry for pre-reset gpio +- num-lanes: number of lanes to use +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this + is specified we'll defer probe until we can find this regulator. +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this + is specified we'll defer probe until we can find this regulator. +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this + is specified we'll defer probe until we can find this regulator. + +Example: + +pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>; + clock-names = "aclk", "aclk-perf", + "hclk"; + bus-range = <0x0 0x1>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names: "sys", "legacy", "client"; + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; + assigned-clock-rates = <100000000>; + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000 + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >; + num-lanes = <4>; + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >; + reg-name = "axi-base", "apb-base"; + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0 1>, + <0 0 0 2 &pcie0 2>, + <0 0 0 3 &pcie0 3>, + <0 0 0 4 &pcie0 4>; +};
This patch adds a binding that describes the Rockchip PCIe controller found on Rockchip SoCs PCIe interface. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> --- Changes in v2: - fix lots clk/reset stuff suggested by Heiko - remove msi-parent and add msi-map suggested by Marc - drop phy related stuff - some others minor fixes .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt