diff mbox

[RESEND,2/4] pwm: mediatek: fix clk issue

Message ID 1498032672-7172-3-git-send-email-zhi.mao@mediatek.com (mailing list archive)
State New, archived
Headers show

Commit Message

Zhi Mao June 21, 2017, 8:11 a.m. UTC 
1.fix clock control
 - prepare top/main clk in mtk_pwm_probe() function,
   it will increase power consumption
   and in original code these clocks is only prepeare but never enabled
 - pwm clock should be enabled before setting pwm registers
   in function: mtk_pwm_config()

2.fix pwm source clock selection
 - in original code, the pwm output frequency is not correct
   when set bit<3>=1 to PWMCON register.

Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
---
 drivers/pwm/pwm-mediatek.c |   69 +++++++++++++++++++++++++++-----------------
 1 file changed, 43 insertions(+), 26 deletions(-)

Comments

John Crispin June 21, 2017, 12:07 p.m. UTC | #1 
Hi

comments inline


On 21/06/17 10:11, Zhi Mao wrote:
> 1.fix clock control
>   - prepare top/main clk in mtk_pwm_probe() function,
>     it will increase power consumption
>     and in original code these clocks is only prepeare but never enabled
>   - pwm clock should be enabled before setting pwm registers
>     in function: mtk_pwm_config()
>
> 2.fix pwm source clock selection
>   - in original code, the pwm output frequency is not correct
>     when set bit<3>=1 to PWMCON register.
>
> Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
> ---
>   drivers/pwm/pwm-mediatek.c |   69 +++++++++++++++++++++++++++-----------------
>   1 file changed, 43 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/pwm/pwm-mediatek.c b/drivers/pwm/pwm-mediatek.c
> index 5c11bc7..c803ff6 100644
> --- a/drivers/pwm/pwm-mediatek.c
> +++ b/drivers/pwm/pwm-mediatek.c
> @@ -2,6 +2,7 @@
>    * Mediatek Pulse Width Modulator driver
>    *
>    * Copyright (C) 2015 John Crispin <blogic@openwrt.org>
> + * Copyright (C) 2017 Zhi Mao <zhi.mao@mediatek.com>
>    *
>    * This file is licensed under the terms of the GNU General Public
>    * License version 2. This program is licensed "as is" without any
> @@ -61,6 +62,40 @@ static inline struct mtk_pwm_chip *to_mtk_pwm_chip(struct pwm_chip *chip)
>   	return container_of(chip, struct mtk_pwm_chip, chip);
>   }
>   
> +static int mtk_pwm_clk_enable(struct pwm_chip *chip, struct pwm_device *pwm)
> +{
> +	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
> +	int ret = 0;
> +
> +	ret = clk_prepare_enable(pc->clks[MTK_CLK_TOP]);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = clk_prepare_enable(pc->clks[MTK_CLK_MAIN]);
> +	if (ret < 0) {
> +		clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> +	if (ret < 0) {
> +		clk_disable_unprepare(pc->clks[MTK_CLK_MAIN]);
> +		clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
> +		return ret;
> +	}
> +
Rather than disabling the already prepared clks in each error path and 
then returning, you should use goto err_clk_{top,main,pwm1} in the same 
style as what this patch removes from mtk_pwm_probe()

> +	return ret;
> +}
> +
> +static void mtk_pwm_clk_disable(struct pwm_chip *chip, struct pwm_device *pwm)
> +{
> +	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
> +
> +	clk_disable_unprepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> +	clk_disable_unprepare(pc->clks[MTK_CLK_MAIN]);
> +	clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
> +}
> +
>   static inline u32 mtk_pwm_readl(struct mtk_pwm_chip *chip, unsigned int num,
>   				unsigned int offset)
>   {
> @@ -81,6 +116,8 @@ static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
>   	struct clk *clk = pc->clks[MTK_CLK_PWM1 + pwm->hwpwm];
>   	u32 resolution, clkdiv = 0;
>   
> +	mtk_pwm_clk_enable(chip, pwm);
> +
>   	resolution = NSEC_PER_SEC / clk_get_rate(clk);
>   
>   	while (period_ns / resolution > 8191) {
> @@ -91,10 +128,12 @@ static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
>   	if (clkdiv > 7)
>   		return -EINVAL;
>   
> -	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) | clkdiv);
> +	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);

this chunk needs to go into its own patch

>   	mtk_pwm_writel(pc, pwm->hwpwm, PWMDWIDTH, period_ns / resolution);
>   	mtk_pwm_writel(pc, pwm->hwpwm, PWMTHRES, duty_ns / resolution);
>   
> +	mtk_pwm_clk_disable(chip, pwm);
> +
>   	return 0;
>   }
>   
> @@ -102,11 +141,8 @@ static int mtk_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
>   {
>   	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
>   	u32 value;
> -	int ret;
>   
> -	ret = clk_prepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> -	if (ret < 0)
> -		return ret;
> +	mtk_pwm_clk_enable(chip, pwm);
You need to check the error code here and return if clk enabling failed

>   
>   	value = readl(pc->regs);
>   	value |= BIT(pwm->hwpwm);
> @@ -124,7 +160,7 @@ static void mtk_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
>   	value &= ~BIT(pwm->hwpwm);
>   	writel(value, pc->regs);
>   
> -	clk_unprepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> +	mtk_pwm_clk_disable(chip, pwm);
>   }
>   
>   static const struct pwm_ops mtk_pwm_ops = {
> @@ -156,14 +192,6 @@ static int mtk_pwm_probe(struct platform_device *pdev)
>   			return PTR_ERR(pc->clks[i]);
>   	}
>   
> -	ret = clk_prepare(pc->clks[MTK_CLK_TOP]);
> -	if (ret < 0)
> -		return ret;
> -
> -	ret = clk_prepare(pc->clks[MTK_CLK_MAIN]);
> -	if (ret < 0)
> -		goto disable_clk_top;
> -
>   	platform_set_drvdata(pdev, pc);
>   
>   	pc->chip.dev = &pdev->dev;
> @@ -174,26 +202,15 @@ static int mtk_pwm_probe(struct platform_device *pdev)
>   	ret = pwmchip_add(&pc->chip);
>   	if (ret < 0) {
>   		dev_err(&pdev->dev, "pwmchip_add() failed: %d\n", ret);
> -		goto disable_clk_main;
> +		return ret;
>   	}
>   
>   	return 0;
> -
> -disable_clk_main:
> -	clk_unprepare(pc->clks[MTK_CLK_MAIN]);
> -disable_clk_top:
> -	clk_unprepare(pc->clks[MTK_CLK_TOP]);
> -
> -	return ret;
>   }
>   
>   static int mtk_pwm_remove(struct platform_device *pdev)
>   {
>   	struct mtk_pwm_chip *pc = platform_get_drvdata(pdev);
> -	unsigned int i;
> -
> -	for (i = 0; i < pc->chip.npwm; i++)
> -		pwm_disable(&pc->chip.pwms[i]);
why are you removing this chunk ?

     John

>   
>   	return pwmchip_remove(&pc->chip);
>   }
Zhi Mao June 22, 2017, 12:48 p.m. UTC | #2 
On Wed, 2017-06-21 at 20:07 +0800, John Crispin wrote:
> Hi
> 
> comments inline
> 
> 
> > +static int mtk_pwm_clk_enable(struct pwm_chip *chip, struct pwm_device *pwm)
> > +{

> > +	ret = clk_prepare_enable(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> > +	if (ret < 0) {
> > +		clk_disable_unprepare(pc->clks[MTK_CLK_MAIN]);
> > +		clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
> > +		return ret;
> > +	}
> > +
> Rather than disabling the already prepared clks in each error path and 
> then returning, you should use goto err_clk_{top,main,pwm1} in the same 
> style as what this patch removes from mtk_pwm_probe()
> 
> > +	return ret;
> > +}

> >   static inline u32 mtk_pwm_readl(struct mtk_pwm_chip *chip, unsigned int num,
> >   				unsigned int offset)
> >   {

> > @@ -91,10 +128,12 @@ static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
> >   	if (clkdiv > 7)
> >   		return -EINVAL;
> >   
> > -	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) | clkdiv);
> > +	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
> 
> this chunk needs to go into its own patch
> 

> >   
> > @@ -102,11 +141,8 @@ static int mtk_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
> >   {
> >   
> > -	ret = clk_prepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
> > -	if (ret < 0)
> > -		return ret;
> > +	mtk_pwm_clk_enable(chip, pwm);
> You need to check the error code here and return if clk enabling failed
> 

<....>
Hi John,
For these above comments, I will modified as your suggestions in the
next release.

> > 
> >   
> >   static int mtk_pwm_remove(struct platform_device *pdev)
> >   {
> >   	struct mtk_pwm_chip *pc = platform_get_drvdata(pdev);
> > -	unsigned int i;
> > -
> > -	for (i = 0; i < pc->chip.npwm; i++)
> > -		pwm_disable(&pc->chip.pwms[i]);
> why are you removing this chunk ?
> 
>      John
> 

After refering to some other vendor's pwm driver, we think the
"pwm_disable" is no need, and framework control flow should disable all
the pwms before removing them,
so we remove it.

Regards,
Zhi

> >   
> >   	return pwmchip_remove(&pc->chip);
> >   }
>
diff mbox

Patch

diff --git a/drivers/pwm/pwm-mediatek.c b/drivers/pwm/pwm-mediatek.c
index 5c11bc7..c803ff6 100644
--- a/drivers/pwm/pwm-mediatek.c
+++ b/drivers/pwm/pwm-mediatek.c
@@ -2,6 +2,7 @@ 
  * Mediatek Pulse Width Modulator driver
  *
  * Copyright (C) 2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2017 Zhi Mao <zhi.mao@mediatek.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any
@@ -61,6 +62,40 @@  static inline struct mtk_pwm_chip *to_mtk_pwm_chip(struct pwm_chip *chip)
 	return container_of(chip, struct mtk_pwm_chip, chip);
 }
 
+static int mtk_pwm_clk_enable(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
+	int ret = 0;
+
+	ret = clk_prepare_enable(pc->clks[MTK_CLK_TOP]);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_prepare_enable(pc->clks[MTK_CLK_MAIN]);
+	if (ret < 0) {
+		clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
+	if (ret < 0) {
+		clk_disable_unprepare(pc->clks[MTK_CLK_MAIN]);
+		clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
+		return ret;
+	}
+
+	return ret;
+}
+
+static void mtk_pwm_clk_disable(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
+
+	clk_disable_unprepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
+	clk_disable_unprepare(pc->clks[MTK_CLK_MAIN]);
+	clk_disable_unprepare(pc->clks[MTK_CLK_TOP]);
+}
+
 static inline u32 mtk_pwm_readl(struct mtk_pwm_chip *chip, unsigned int num,
 				unsigned int offset)
 {
@@ -81,6 +116,8 @@  static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 	struct clk *clk = pc->clks[MTK_CLK_PWM1 + pwm->hwpwm];
 	u32 resolution, clkdiv = 0;
 
+	mtk_pwm_clk_enable(chip, pwm);
+
 	resolution = NSEC_PER_SEC / clk_get_rate(clk);
 
 	while (period_ns / resolution > 8191) {
@@ -91,10 +128,12 @@  static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 	if (clkdiv > 7)
 		return -EINVAL;
 
-	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) | clkdiv);
+	mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
 	mtk_pwm_writel(pc, pwm->hwpwm, PWMDWIDTH, period_ns / resolution);
 	mtk_pwm_writel(pc, pwm->hwpwm, PWMTHRES, duty_ns / resolution);
 
+	mtk_pwm_clk_disable(chip, pwm);
+
 	return 0;
 }
 
@@ -102,11 +141,8 @@  static int mtk_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip);
 	u32 value;
-	int ret;
 
-	ret = clk_prepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
-	if (ret < 0)
-		return ret;
+	mtk_pwm_clk_enable(chip, pwm);
 
 	value = readl(pc->regs);
 	value |= BIT(pwm->hwpwm);
@@ -124,7 +160,7 @@  static void mtk_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 	value &= ~BIT(pwm->hwpwm);
 	writel(value, pc->regs);
 
-	clk_unprepare(pc->clks[MTK_CLK_PWM1 + pwm->hwpwm]);
+	mtk_pwm_clk_disable(chip, pwm);
 }
 
 static const struct pwm_ops mtk_pwm_ops = {
@@ -156,14 +192,6 @@  static int mtk_pwm_probe(struct platform_device *pdev)
 			return PTR_ERR(pc->clks[i]);
 	}
 
-	ret = clk_prepare(pc->clks[MTK_CLK_TOP]);
-	if (ret < 0)
-		return ret;
-
-	ret = clk_prepare(pc->clks[MTK_CLK_MAIN]);
-	if (ret < 0)
-		goto disable_clk_top;
-
 	platform_set_drvdata(pdev, pc);
 
 	pc->chip.dev = &pdev->dev;
@@ -174,26 +202,15 @@  static int mtk_pwm_probe(struct platform_device *pdev)
 	ret = pwmchip_add(&pc->chip);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "pwmchip_add() failed: %d\n", ret);
-		goto disable_clk_main;
+		return ret;
 	}
 
 	return 0;
-
-disable_clk_main:
-	clk_unprepare(pc->clks[MTK_CLK_MAIN]);
-disable_clk_top:
-	clk_unprepare(pc->clks[MTK_CLK_TOP]);
-
-	return ret;
 }
 
 static int mtk_pwm_remove(struct platform_device *pdev)
 {
 	struct mtk_pwm_chip *pc = platform_get_drvdata(pdev);
-	unsigned int i;
-
-	for (i = 0; i < pc->chip.npwm; i++)
-		pwm_disable(&pc->chip.pwms[i]);
 
 	return pwmchip_remove(&pc->chip);
 }