| Message ID | 1523973390-2387-1-git-send-email-yossim@codeaurora.org (mailing list archive) |
|---|---|
| State | Deferred, archived |
| Delegated to: | Andy Gross |
| Headers | show |
Quoting Yossi Mansharoff (2018-04-17 06:56:30) > We currently have three device nodes for the same USB hardware > block, as evident by the reuse of the same reg address multiple > times. Now that the chipidea driver fully supports OTG with the > MSM wrapper we can collapse all these nodes into one USB device > node, reflecting the true nature of the hardware. None of this makes sense. Commit text is totally bogus now. > > diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > index 9ff8487..1505921 100644 > --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > @@ -371,18 +372,18 @@ > adp-disable; > hnp-disable; > srp-disable; > - dr_mode = "host"; > - pinctrl-names = "default"; > - pinctrl-0 = <&usb_sw_sel_pm>; > + mux-controls = <&usb_switch>; > + mux-control-names = "usb_switch"; > + > ulpi { > phy { > v1p8-supply = <&pm8916_l7>; > v3p3-supply = <&pm8916_l13>; > - extcon = <&usb_id>; > }; > }; > }; > > + Why the newline? > lpass@7708000 { > status = "okay"; > }; > @@ -512,11 +513,17 @@ > > usb_id: usb-id { > compatible = "linux,extcon-usb-gpio"; > - vbus-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; > + id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; Hmm? > pinctrl-names = "default"; > pinctrl-0 = <&usb_id_default>; > }; > > + usb_switch: usb-switch { > + compatible = "gpio-mux"; Needs a better compatible string for the actual mux part. The gpio-mux can come after that because it's generic, but it's good to record the actual mux part too. > + mux-gpios = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; > + #mux-control-cells = <0>; > + }; -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 9ff8487..1505921 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -18,6 +18,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/sound/apq8016-lpass.h> +#include <dt-bindings/mux/mux.h> /* * GPIO name legend: proper name = the GPIO line is used as GPIO @@ -371,18 +372,18 @@ adp-disable; hnp-disable; srp-disable; - dr_mode = "host"; - pinctrl-names = "default"; - pinctrl-0 = <&usb_sw_sel_pm>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + ulpi { phy { v1p8-supply = <&pm8916_l7>; v3p3-supply = <&pm8916_l13>; - extcon = <&usb_id>; }; }; }; + lpass@7708000 { status = "okay"; }; @@ -512,11 +513,17 @@ usb_id: usb-id { compatible = "linux,extcon-usb-gpio"; - vbus-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; + id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&usb_id_default>; }; + usb_switch: usb-switch { + compatible = "gpio-mux"; + mux-gpios = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + #mux-control-cells = <0>; + }; + hdmi-out { compatible = "hdmi-connector"; type = "a";
We currently have three device nodes for the same USB hardware block, as evident by the reuse of the same reg address multiple times. Now that the chipidea driver fully supports OTG with the MSM wrapper we can collapse all these nodes into one USB device node, reflecting the true nature of the hardware. Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> --- arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)