Message ID | 20180616062718.29844-5-bgodavar@codeaurora.org (mailing list archive) |
---|---|
State | Not Applicable, archived |
Delegated to: | Andy Gross |
Headers | show |
On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: > Redefinition of qca_uart_setup will help future Qualcomm Bluetooth > SoC, to use the same function instead of duplicating the function. > Added new arguments soc_type and soc_ver to the functions. > > These arguments will help to decide type of firmware files > to be loaded into Bluetooth chip. > soc_type holds the Bluetooth chip connected to APPS processor. > soc_ver holds the Bluetooth chip version. > > Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> > --- > > Changes in v7: > * initial patch > * redefined qca_uart_setup function to generic. > > --- > drivers/bluetooth/btqca.c | 23 ++++++++++++----------- > drivers/bluetooth/btqca.h | 13 +++++++++++-- > drivers/bluetooth/hci_qca.c | 3 ++- > 3 files changed, 25 insertions(+), 14 deletions(-) > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c > index c5cf9cab438a..f748730039cf 100644 > --- a/drivers/bluetooth/btqca.c > +++ b/drivers/bluetooth/btqca.c > @@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr) > } > EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome); > > -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) > +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t soc_type, Use 'enum qca_btsoc_type' as type for 'soc_type'. > + u32 soc_ver) > { > - u32 rome_ver = 0; > struct rome_config config; > int err; > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) > > config.user_baud_rate = baudrate; > > - /* Get QCA version information */ > - err = qca_read_soc_version(hdev, &rome_ver); > - if (err < 0 || rome_ver == 0) { > - bt_dev_err(hdev, "QCA Failed to get version %d", err); > - return err; > + if (!soc_ver) { > + /* Get QCA version information */ > + err = qca_read_soc_version(hdev, &soc_ver); > + if (err < 0 || soc_ver == 0) { > + bt_dev_err(hdev, "QCA Failed to get version %d", err); > + return err; > + } > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); > } Why is this needed? A caller that passes in soc_ver = 0 could just call qca_read_soc_version() themselves. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Matthias, Please find my comments inline. On 2018-06-19 02:49, Matthias Kaehlcke wrote: > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: >> Redefinition of qca_uart_setup will help future Qualcomm Bluetooth >> SoC, to use the same function instead of duplicating the function. >> Added new arguments soc_type and soc_ver to the functions. >> >> These arguments will help to decide type of firmware files >> to be loaded into Bluetooth chip. >> soc_type holds the Bluetooth chip connected to APPS processor. >> soc_ver holds the Bluetooth chip version. >> >> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> >> --- >> >> Changes in v7: >> * initial patch >> * redefined qca_uart_setup function to generic. >> >> --- >> drivers/bluetooth/btqca.c | 23 ++++++++++++----------- >> drivers/bluetooth/btqca.h | 13 +++++++++++-- >> drivers/bluetooth/hci_qca.c | 3 ++- >> 3 files changed, 25 insertions(+), 14 deletions(-) >> >> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c >> index c5cf9cab438a..f748730039cf 100644 >> --- a/drivers/bluetooth/btqca.c >> +++ b/drivers/bluetooth/btqca.c >> @@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, >> const bdaddr_t *bdaddr) >> } >> EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome); >> >> -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) >> +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t >> soc_type, > > Use 'enum qca_btsoc_type' as type for 'soc_type'. > [Bala]: will update. >> + u32 soc_ver) >> { >> - u32 rome_ver = 0; >> struct rome_config config; >> int err; >> >> @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t >> baudrate) >> >> config.user_baud_rate = baudrate; >> >> - /* Get QCA version information */ >> - err = qca_read_soc_version(hdev, &rome_ver); >> - if (err < 0 || rome_ver == 0) { >> - bt_dev_err(hdev, "QCA Failed to get version %d", err); >> - return err; >> + if (!soc_ver) { >> + /* Get QCA version information */ >> + err = qca_read_soc_version(hdev, &soc_ver); >> + if (err < 0 || soc_ver == 0) { >> + bt_dev_err(hdev, "QCA Failed to get version %d", err); >> + return err; >> + } >> + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); >> } > > Why is this needed? A caller that passes in soc_ver = 0 could just > call qca_read_soc_version() themselves. [Bala]: hci_qca support two chip one ROME (already up-streamed) and other wcn3990. there setup sequence differs. wcn3900: 1. set baudrate to 115200 2. read soc version 3. set baudarte to 3.2Mbps 4. download firmware. (calls qca_uart_setup) ROME: 1. set baudrate to 3.0 mbps 2. calls qca_uart_setup to read soc version and download firmware. so to make use of existing function qca_setup_uart(). passing soc_ver as argument. if soc_ver is zero, then read soc version (i.e. for ROME chip). Pls let me know, if you have any queries.
On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: > Hi Matthias, > > Please find my comments inline. > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: > > > Redefinition of qca_uart_setup will help future Qualcomm Bluetooth > > > SoC, to use the same function instead of duplicating the function. > > > Added new arguments soc_type and soc_ver to the functions. > > > > > > These arguments will help to decide type of firmware files > > > to be loaded into Bluetooth chip. > > > soc_type holds the Bluetooth chip connected to APPS processor. > > > soc_ver holds the Bluetooth chip version. > > > > > > Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> > > > --- > > > > > > Changes in v7: > > > * initial patch > > > * redefined qca_uart_setup function to generic. > > > > > > --- > > > drivers/bluetooth/btqca.c | 23 ++++++++++++----------- > > > drivers/bluetooth/btqca.h | 13 +++++++++++-- > > > drivers/bluetooth/hci_qca.c | 3 ++- > > > 3 files changed, 25 insertions(+), 14 deletions(-) > > > > > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c > > > index c5cf9cab438a..f748730039cf 100644 > > > --- a/drivers/bluetooth/btqca.c > > > +++ b/drivers/bluetooth/btqca.c > > > @@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, > > > const bdaddr_t *bdaddr) > > > } > > > EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome); > > > > > > -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) > > > +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t > > > soc_type, > > > > Use 'enum qca_btsoc_type' as type for 'soc_type'. > > > > [Bala]: will update. > > > > + u32 soc_ver) > > > { > > > - u32 rome_ver = 0; > > > struct rome_config config; > > > int err; > > > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, > > > uint8_t baudrate) > > > > > > config.user_baud_rate = baudrate; > > > > > > - /* Get QCA version information */ > > > - err = qca_read_soc_version(hdev, &rome_ver); > > > - if (err < 0 || rome_ver == 0) { > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > - return err; > > > + if (!soc_ver) { > > > + /* Get QCA version information */ > > > + err = qca_read_soc_version(hdev, &soc_ver); > > > + if (err < 0 || soc_ver == 0) { > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > + return err; > > > + } > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); > > > } > > > > Why is this needed? A caller that passes in soc_ver = 0 could just > > call qca_read_soc_version() themselves. > [Bala]: hci_qca support two chip one ROME (already up-streamed) and other > wcn3990. > there setup sequence differs. > > wcn3900: > 1. set baudrate to 115200 > 2. read soc version > 3. set baudarte to 3.2Mbps > 4. download firmware. (calls qca_uart_setup) > > ROME: > 1. set baudrate to 3.0 mbps > 2. calls qca_uart_setup to read soc version and download firmware. > > so to make use of existing function qca_setup_uart(). passing soc_ver > as argument. > if soc_ver is zero, then read soc version (i.e. for ROME chip). > > Pls let me know, if you have any queries. I don't really understand this argumentation. Let's look at the code at the end of this series, where both Rome and wcn3900 are supported: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 The version could be read (for Rome only) after setting the operating speed: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in qca_setup() is kinda ugly, but I think it's still better than the conditional call of qca_read_soc_version() in qca_uart_setup(). -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Matthias, On 2018-06-20 01:33, Matthias Kaehlcke wrote: > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: >> Hi Matthias, >> >> Please find my comments inline. >> >> On 2018-06-19 02:49, Matthias Kaehlcke wrote: >> > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: >> > > Redefinition of qca_uart_setup will help future Qualcomm Bluetooth >> > > SoC, to use the same function instead of duplicating the function. >> > > Added new arguments soc_type and soc_ver to the functions. >> > > >> > > These arguments will help to decide type of firmware files >> > > to be loaded into Bluetooth chip. >> > > soc_type holds the Bluetooth chip connected to APPS processor. >> > > soc_ver holds the Bluetooth chip version. >> > > >> > > Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> >> > > --- >> > > >> > > Changes in v7: >> > > * initial patch >> > > * redefined qca_uart_setup function to generic. >> > > >> > > --- >> > > drivers/bluetooth/btqca.c | 23 ++++++++++++----------- >> > > drivers/bluetooth/btqca.h | 13 +++++++++++-- >> > > drivers/bluetooth/hci_qca.c | 3 ++- >> > > 3 files changed, 25 insertions(+), 14 deletions(-) >> > > >> > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c >> > > index c5cf9cab438a..f748730039cf 100644 >> > > --- a/drivers/bluetooth/btqca.c >> > > +++ b/drivers/bluetooth/btqca.c >> > > @@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, >> > > const bdaddr_t *bdaddr) >> > > } >> > > EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome); >> > > >> > > -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) >> > > +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t >> > > soc_type, >> > >> > Use 'enum qca_btsoc_type' as type for 'soc_type'. >> > >> >> [Bala]: will update. >> >> > > + u32 soc_ver) >> > > { >> > > - u32 rome_ver = 0; >> > > struct rome_config config; >> > > int err; >> > > >> > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, >> > > uint8_t baudrate) >> > > >> > > config.user_baud_rate = baudrate; >> > > >> > > - /* Get QCA version information */ >> > > - err = qca_read_soc_version(hdev, &rome_ver); >> > > - if (err < 0 || rome_ver == 0) { >> > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > - return err; >> > > + if (!soc_ver) { >> > > + /* Get QCA version information */ >> > > + err = qca_read_soc_version(hdev, &soc_ver); >> > > + if (err < 0 || soc_ver == 0) { >> > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > + return err; >> > > + } >> > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); >> > > } >> > >> > Why is this needed? A caller that passes in soc_ver = 0 could just >> > call qca_read_soc_version() themselves. >> [Bala]: hci_qca support two chip one ROME (already up-streamed) and >> other >> wcn3990. >> there setup sequence differs. >> >> wcn3900: >> 1. set baudrate to 115200 >> 2. read soc version >> 3. set baudarte to 3.2Mbps >> 4. download firmware. (calls qca_uart_setup) >> >> ROME: >> 1. set baudrate to 3.0 mbps >> 2. calls qca_uart_setup to read soc version and download >> firmware. >> >> so to make use of existing function qca_setup_uart(). passing >> soc_ver >> as argument. >> if soc_ver is zero, then read soc version (i.e. for ROME chip). >> >> Pls let me know, if you have any queries. > > I don't really understand this argumentation. Let's look at the code > at the end of this series, where both Rome and wcn3900 are supported: > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 > > The version could be read (for Rome only) after setting the operating > speed: [Bala]: yes we can read SoC version after setting operating baud rate. an advice from SoC vendor that, read SoC version before setting operating speed. one advantage from reading SoC version before setting operating baudrate,it will helps us to understand whether the soc is responding to any commands in default baud rate before setting operating speed. > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in > qca_setup() is kinda ugly, but I think it's still better than the > conditional call of qca_read_soc_version() in qca_uart_setup(). [Bala]: we require an if-else block for soc type.As wcn3900 support hardware flow control where as ROME is not supporting hardware flow control.
Hi Balakrishna, On Wed, Jun 20, 2018 at 04:23:25PM +0530, Balakrishna Godavarthi wrote: > Hi Matthias, > > On 2018-06-20 01:33, Matthias Kaehlcke wrote: > > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: > > > Hi Matthias, > > > > > > Please find my comments inline. > > > > > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: > > > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: > > > > > > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, > > > > > uint8_t baudrate) > > > > > > > > > > config.user_baud_rate = baudrate; > > > > > > > > > > - /* Get QCA version information */ > > > > > - err = qca_read_soc_version(hdev, &rome_ver); > > > > > - if (err < 0 || rome_ver == 0) { > > > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > - return err; > > > > > + if (!soc_ver) { > > > > > + /* Get QCA version information */ > > > > > + err = qca_read_soc_version(hdev, &soc_ver); > > > > > + if (err < 0 || soc_ver == 0) { > > > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > + return err; > > > > > + } > > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); > > > > > } > > > > > > > > Why is this needed? A caller that passes in soc_ver = 0 could just > > > > call qca_read_soc_version() themselves. > > > [Bala]: hci_qca support two chip one ROME (already up-streamed) and > > > other > > > wcn3990. > > > there setup sequence differs. > > > > > > wcn3900: > > > 1. set baudrate to 115200 > > > 2. read soc version > > > 3. set baudarte to 3.2Mbps > > > 4. download firmware. (calls qca_uart_setup) > > > > > > ROME: > > > 1. set baudrate to 3.0 mbps > > > 2. calls qca_uart_setup to read soc version and download > > > firmware. > > > > > > so to make use of existing function qca_setup_uart(). passing > > > soc_ver > > > as argument. > > > if soc_ver is zero, then read soc version (i.e. for ROME chip). > > > > > > Pls let me know, if you have any queries. > > > > I don't really understand this argumentation. Let's look at the code > > at the end of this series, where both Rome and wcn3900 are supported: > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 > > > > The version could be read (for Rome only) after setting the operating > > speed: > > [Bala]: yes we can read SoC version after setting operating baud rate. an > advice from SoC vendor that, read SoC version before setting operating > speed. > one advantage from reading SoC version before setting operating > baudrate,it will helps us to understand whether the soc is responding to any > commands in default baud rate > before setting operating speed. Is the recommendation for Rome or wcn3990? I was referring to Rome and the current code sets the operating speed and then reads the SoC version (inside qca_uart_setup()) > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > > > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in > > qca_setup() is kinda ugly, but I think it's still better than the > > conditional call of qca_read_soc_version() in qca_uart_setup(). > > [Bala]: we require an if-else block for soc type.As wcn3900 support > hardware flow control where as ROME is not supporting hardware flow control. Since you mention if-else and flow control I'm not sure if you understood correctly what I suggested. My suggestion is to add something like this: if (qcadev->btsoc_type == QCA_ROME) { ret = qca_read_soc_version(hdev, &soc_ver); if (ret < 0 || soc_ver == 0) { // Note mka@: we might want to skip this log, // qca_read_soc_version() already logs in all error paths bt_dev_err(hdev, "Failed to get version %d", ret); return ret; } } right here: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 which is functionally equivalent to the current code. You could even do the error check in the common code (just checking for 'soc_ver == 0', assuming that qca_read_soc_version() doesn't set it to something different in case of error). Anyway, I won't insist if you prefer it as is and Marcel is ok with it. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Matthias, On 2018-06-21 05:03, Matthias Kaehlcke wrote: > Hi Balakrishna, > > On Wed, Jun 20, 2018 at 04:23:25PM +0530, Balakrishna Godavarthi wrote: >> Hi Matthias, >> >> On 2018-06-20 01:33, Matthias Kaehlcke wrote: >> > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: >> > > Hi Matthias, >> > > >> > > Please find my comments inline. >> > > >> > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: >> > > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: >> > > > >> > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, >> > > > > uint8_t baudrate) >> > > > > >> > > > > config.user_baud_rate = baudrate; >> > > > > >> > > > > - /* Get QCA version information */ >> > > > > - err = qca_read_soc_version(hdev, &rome_ver); >> > > > > - if (err < 0 || rome_ver == 0) { >> > > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > > > - return err; >> > > > > + if (!soc_ver) { >> > > > > + /* Get QCA version information */ >> > > > > + err = qca_read_soc_version(hdev, &soc_ver); >> > > > > + if (err < 0 || soc_ver == 0) { >> > > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > > > + return err; >> > > > > + } >> > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); >> > > > > } >> > > > >> > > > Why is this needed? A caller that passes in soc_ver = 0 could just >> > > > call qca_read_soc_version() themselves. >> > > [Bala]: hci_qca support two chip one ROME (already up-streamed) and >> > > other >> > > wcn3990. >> > > there setup sequence differs. >> > > >> > > wcn3900: >> > > 1. set baudrate to 115200 >> > > 2. read soc version >> > > 3. set baudarte to 3.2Mbps >> > > 4. download firmware. (calls qca_uart_setup) >> > > >> > > ROME: >> > > 1. set baudrate to 3.0 mbps >> > > 2. calls qca_uart_setup to read soc version and download >> > > firmware. >> > > >> > > so to make use of existing function qca_setup_uart(). passing >> > > soc_ver >> > > as argument. >> > > if soc_ver is zero, then read soc version (i.e. for ROME chip). >> > > >> > > Pls let me know, if you have any queries. >> > >> > I don't really understand this argumentation. Let's look at the code >> > at the end of this series, where both Rome and wcn3900 are supported: >> > >> > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 >> > >> > The version could be read (for Rome only) after setting the operating >> > speed: >> >> [Bala]: yes we can read SoC version after setting operating baud rate. >> an >> advice from SoC vendor that, read SoC version before setting operating >> speed. >> one advantage from reading SoC version before setting >> operating >> baudrate,it will helps us to understand whether the soc is responding >> to any >> commands in default baud rate >> before setting operating speed. > > Is the recommendation for Rome or wcn3990? I was referring to Rome and > the current code sets the operating speed and then reads the SoC > version (inside qca_uart_setup()) > [Bala]: my statement is wrt to wcn3990. yes, ROME will set operating speed and read version. >> > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 >> > >> > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in >> > qca_setup() is kinda ugly, but I think it's still better than the >> > conditional call of qca_read_soc_version() in qca_uart_setup(). >> >> [Bala]: we require an if-else block for soc type.As wcn3900 support >> hardware flow control where as ROME is not supporting hardware flow >> control. > > Since you mention if-else and flow control I'm not sure if you > understood correctly what I suggested. My suggestion is to add > something like this: > > if (qcadev->btsoc_type == QCA_ROME) { > ret = qca_read_soc_version(hdev, &soc_ver); > if (ret < 0 || soc_ver == 0) { > // Note mka@: we might want to skip this log, > // qca_read_soc_version() already logs in all error paths > bt_dev_err(hdev, "Failed to get version %d", ret); > return ret; > } > } > > right here: > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > which is functionally equivalent to the current code. > > You could even do the error check in the common code (just checking > for 'soc_ver == 0', assuming that qca_read_soc_version() doesn't set > it to something different in case of error). > > Anyway, I won't insist if you prefer it as is and Marcel is ok with it. [Bala]: thanks for clarifying my doubt, but if remove the qca_read_soc_version() from qca_uart_setup() and handle it qca_setup(). in that case, we will have common blocks of code, when we integrate wcn3990 into existing qca_setup() static int qca_setup(struct hci_uart *hu) { ... qcadev = serdev_device_get_drvdata(hu->serdev); /* Patch downloading has to be done without IBS mode */ clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); /* Setup initial baudrate */ speed = qca_get_speed(hu, QCA_INIT_SPEED); if (speed) qca_set_speed(hu, speed, QCA_INIT_SPEED); if (qcadev->btsoc_type == QCA_WCN3990) { bt_dev_dbg(hdev, "setting up wcn3990"); hci_uart_set_flow_control(hu, true); ret = qca_send_vendor_cmd(hdev, QCA_WCN3990_POWERON_PULSE); if (ret) { bt_dev_err(hdev, "failed to send power on command"); return ret; } serdev_device_close(hu->serdev); ret = serdev_device_open(hu->serdev); if (ret) { bt_dev_err(hdev, "failed to open port"); return ret; } msleep(100); speed = qca_get_speed(hu, QCA_INIT_SPEED); if (speed) qca_set_speed(hu, speed, QCA_INIT_SPEED); hci_uart_set_flow_control(hu, false); } else { bt_dev_info(hdev, "ROME setup"); /* Setup user speed if needed */ speed = qca_get_speed(hu, QCA_OPER_SPEED); if (speed) { ret = qca_set_speed(hu, speed, QCA_OPER_SPEED); if (ret) return ret; qca_baudrate = qca_get_baudrate_value(speed); } } ret = qca_read_soc_version(hdev, &soc_ver); if (ret < 0 || soc_ver == 0) { bt_dev_err(hdev, "Failed to get version %d", ret); return ret; } bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); if (qcadev->btsoc_type == QCA_WCN3990) { hci_uart_set_flow_control(hu, true); /* Setup user speed if needed */ speed = qca_get_speed(hu, QCA_OPER_SPEED); if (speed) { ret = qca_set_speed(hu, speed, QCA_OPER_SPEED); if (ret) return ret; qca_baudrate = qca_get_baudrate_value(speed); } /* Setup patch / NVM configurations */ ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, soc_ver); if (!ret) { set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); qca_debugfs_init(hdev); } else if (ret == -ENOENT) { /* No patch/nvm-config found, run with original fw/config */ ret = 0; } else if (ret == -EAGAIN) { /* ... }
On Thu, Jun 21, 2018 at 04:50:28PM +0530, Balakrishna Godavarthi wrote: > Hi Matthias, > > On 2018-06-21 05:03, Matthias Kaehlcke wrote: > > Hi Balakrishna, > > > > On Wed, Jun 20, 2018 at 04:23:25PM +0530, Balakrishna Godavarthi wrote: > > > Hi Matthias, > > > > > > On 2018-06-20 01:33, Matthias Kaehlcke wrote: > > > > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: > > > > > Hi Matthias, > > > > > > > > > > Please find my comments inline. > > > > > > > > > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: > > > > > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: > > > > > > > > > > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, > > > > > > > uint8_t baudrate) > > > > > > > > > > > > > > config.user_baud_rate = baudrate; > > > > > > > > > > > > > > - /* Get QCA version information */ > > > > > > > - err = qca_read_soc_version(hdev, &rome_ver); > > > > > > > - if (err < 0 || rome_ver == 0) { > > > > > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > > > - return err; > > > > > > > + if (!soc_ver) { > > > > > > > + /* Get QCA version information */ > > > > > > > + err = qca_read_soc_version(hdev, &soc_ver); > > > > > > > + if (err < 0 || soc_ver == 0) { > > > > > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > > > + return err; > > > > > > > + } > > > > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); > > > > > > > } > > > > > > > > > > > > Why is this needed? A caller that passes in soc_ver = 0 could just > > > > > > call qca_read_soc_version() themselves. > > > > > [Bala]: hci_qca support two chip one ROME (already up-streamed) and > > > > > other > > > > > wcn3990. > > > > > there setup sequence differs. > > > > > > > > > > wcn3900: > > > > > 1. set baudrate to 115200 > > > > > 2. read soc version > > > > > 3. set baudarte to 3.2Mbps > > > > > 4. download firmware. (calls qca_uart_setup) > > > > > > > > > > ROME: > > > > > 1. set baudrate to 3.0 mbps > > > > > 2. calls qca_uart_setup to read soc version and download > > > > > firmware. > > > > > > > > > > so to make use of existing function qca_setup_uart(). passing > > > > > soc_ver > > > > > as argument. > > > > > if soc_ver is zero, then read soc version (i.e. for ROME chip). > > > > > > > > > > Pls let me know, if you have any queries. > > > > > > > > I don't really understand this argumentation. Let's look at the code > > > > at the end of this series, where both Rome and wcn3900 are supported: > > > > > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 > > > > > > > > The version could be read (for Rome only) after setting the operating > > > > speed: > > > > > > [Bala]: yes we can read SoC version after setting operating baud > > > rate. an > > > advice from SoC vendor that, read SoC version before setting operating > > > speed. > > > one advantage from reading SoC version before setting > > > operating > > > baudrate,it will helps us to understand whether the soc is > > > responding to any > > > commands in default baud rate > > > before setting operating speed. > > > > Is the recommendation for Rome or wcn3990? I was referring to Rome and > > the current code sets the operating speed and then reads the SoC > > version (inside qca_uart_setup()) > > > > [Bala]: my statement is wrt to wcn3990. yes, ROME will set operating speed > and read version. > > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > > > > > > > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in > > > > qca_setup() is kinda ugly, but I think it's still better than the > > > > conditional call of qca_read_soc_version() in qca_uart_setup(). > > > > > > [Bala]: we require an if-else block for soc type.As wcn3900 support > > > hardware flow control where as ROME is not supporting hardware flow > > > control. > > > > Since you mention if-else and flow control I'm not sure if you > > understood correctly what I suggested. My suggestion is to add > > something like this: > > > > if (qcadev->btsoc_type == QCA_ROME) { > > ret = qca_read_soc_version(hdev, &soc_ver); > > if (ret < 0 || soc_ver == 0) { > > // Note mka@: we might want to skip this log, > > // qca_read_soc_version() already logs in all error paths > > bt_dev_err(hdev, "Failed to get version %d", ret); > > return ret; > > } > > } > > > > right here: > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > > > which is functionally equivalent to the current code. > > > > You could even do the error check in the common code (just checking > > for 'soc_ver == 0', assuming that qca_read_soc_version() doesn't set > > it to something different in case of error). > > > > Anyway, I won't insist if you prefer it as is and Marcel is ok with it. > > [Bala]: thanks for clarifying my doubt, but if remove the > qca_read_soc_version() from qca_uart_setup() and handle it qca_setup(). > in that case, we will have common blocks of code, when we integrate > wcn3990 into existing qca_setup() Excellent! > static int qca_setup(struct hci_uart *hu) > { > ... > > qcadev = serdev_device_get_drvdata(hu->serdev); > > /* Patch downloading has to be done without IBS mode */ > clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > > /* Setup initial baudrate */ > speed = qca_get_speed(hu, QCA_INIT_SPEED); > if (speed) > qca_set_speed(hu, speed, QCA_INIT_SPEED); I said earlier that a _set_speed() followed by a _get_speed() is a bit odd, and that it would be better to get the speed first and pass it as a parameter. After looking again over the larger code I'm not convinced anymore this is such a good idea, since the above pattern is repeated multiple times, when it could be just: qca_set_speed(hu, QCA_INIT_SPEED) (+ error handling, which is also missing in the code above) Just a thought, not asking you to change it back, do whatever seems best to you. > if (qcadev->btsoc_type == QCA_WCN3990) { > bt_dev_dbg(hdev, "setting up wcn3990"); > hci_uart_set_flow_control(hu, true); > ret = qca_send_vendor_cmd(hdev, QCA_WCN3990_POWERON_PULSE); > if (ret) { > bt_dev_err(hdev, "failed to send power on command"); > return ret; > } > > serdev_device_close(hu->serdev); > ret = serdev_device_open(hu->serdev); > if (ret) { > bt_dev_err(hdev, "failed to open port"); > return ret; > } > > msleep(100); > speed = qca_get_speed(hu, QCA_INIT_SPEED); > if (speed) > qca_set_speed(hu, speed, QCA_INIT_SPEED); > > hci_uart_set_flow_control(hu, false); > } else { > bt_dev_info(hdev, "ROME setup"); > /* Setup user speed if needed */ > speed = qca_get_speed(hu, QCA_OPER_SPEED); > if (speed) { > ret = qca_set_speed(hu, speed, QCA_OPER_SPEED); > if (ret) > return ret; > > qca_baudrate = qca_get_baudrate_value(speed); It seems setting 'qca_baudrate' could also be done in the common path. Would require an extra qca_get_speed(hu, QCA_OPER_SPEED) call, in exchange this would be done in a single place closer to where 'qca_baudrate' is actually used. Actually as it is now 'qca_baudrate' could remain uninitialized for Rome if no operating speed is defined, which judging from qca_get_baudrate_value() should result in QCA_BAUDRATE_115200. > } > } > > ret = qca_read_soc_version(hdev, &soc_ver); > if (ret < 0 || soc_ver == 0) { > bt_dev_err(hdev, "Failed to get version %d", ret); > return ret; > } > bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); > > > if (qcadev->btsoc_type == QCA_WCN3990) { > hci_uart_set_flow_control(hu, true); > /* Setup user speed if needed */ > speed = qca_get_speed(hu, QCA_OPER_SPEED); > if (speed) { > ret = qca_set_speed(hu, speed, QCA_OPER_SPEED); > if (ret) > return ret; > > qca_baudrate = qca_get_baudrate_value(speed); > > } > > /* Setup patch / NVM configurations */ > ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, > soc_ver); > if (!ret) { > set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > qca_debugfs_init(hdev); > } else if (ret == -ENOENT) { > /* No patch/nvm-config found, run with original fw/config */ > ret = 0; > } else if (ret == -EAGAIN) { > /* > ... > } Overall looks good and should still become a bit more compact if the handling of flow control is done in _set_speed() as you suggested in "[PATCH v7 8/8] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990" -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Matthias, On 2018-06-22 03:39, Matthias Kaehlcke wrote: > On Thu, Jun 21, 2018 at 04:50:28PM +0530, Balakrishna Godavarthi wrote: >> Hi Matthias, >> >> On 2018-06-21 05:03, Matthias Kaehlcke wrote: >> > Hi Balakrishna, >> > >> > On Wed, Jun 20, 2018 at 04:23:25PM +0530, Balakrishna Godavarthi wrote: >> > > Hi Matthias, >> > > >> > > On 2018-06-20 01:33, Matthias Kaehlcke wrote: >> > > > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: >> > > > > Hi Matthias, >> > > > > >> > > > > Please find my comments inline. >> > > > > >> > > > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: >> > > > > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: >> > > > > > >> > > > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, >> > > > > > > uint8_t baudrate) >> > > > > > > >> > > > > > > config.user_baud_rate = baudrate; >> > > > > > > >> > > > > > > - /* Get QCA version information */ >> > > > > > > - err = qca_read_soc_version(hdev, &rome_ver); >> > > > > > > - if (err < 0 || rome_ver == 0) { >> > > > > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > > > > > - return err; >> > > > > > > + if (!soc_ver) { >> > > > > > > + /* Get QCA version information */ >> > > > > > > + err = qca_read_soc_version(hdev, &soc_ver); >> > > > > > > + if (err < 0 || soc_ver == 0) { >> > > > > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); >> > > > > > > + return err; >> > > > > > > + } >> > > > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); >> > > > > > > } >> > > > > > >> > > > > > Why is this needed? A caller that passes in soc_ver = 0 could just >> > > > > > call qca_read_soc_version() themselves. >> > > > > [Bala]: hci_qca support two chip one ROME (already up-streamed) and >> > > > > other >> > > > > wcn3990. >> > > > > there setup sequence differs. >> > > > > >> > > > > wcn3900: >> > > > > 1. set baudrate to 115200 >> > > > > 2. read soc version >> > > > > 3. set baudarte to 3.2Mbps >> > > > > 4. download firmware. (calls qca_uart_setup) >> > > > > >> > > > > ROME: >> > > > > 1. set baudrate to 3.0 mbps >> > > > > 2. calls qca_uart_setup to read soc version and download >> > > > > firmware. >> > > > > >> > > > > so to make use of existing function qca_setup_uart(). passing >> > > > > soc_ver >> > > > > as argument. >> > > > > if soc_ver is zero, then read soc version (i.e. for ROME chip). >> > > > > >> > > > > Pls let me know, if you have any queries. >> > > > >> > > > I don't really understand this argumentation. Let's look at the code >> > > > at the end of this series, where both Rome and wcn3900 are supported: >> > > > >> > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 >> > > > >> > > > The version could be read (for Rome only) after setting the operating >> > > > speed: >> > > >> > > [Bala]: yes we can read SoC version after setting operating baud >> > > rate. an >> > > advice from SoC vendor that, read SoC version before setting operating >> > > speed. >> > > one advantage from reading SoC version before setting >> > > operating >> > > baudrate,it will helps us to understand whether the soc is >> > > responding to any >> > > commands in default baud rate >> > > before setting operating speed. >> > >> > Is the recommendation for Rome or wcn3990? I was referring to Rome and >> > the current code sets the operating speed and then reads the SoC >> > version (inside qca_uart_setup()) >> > >> >> [Bala]: my statement is wrt to wcn3990. yes, ROME will set operating >> speed >> and read version. >> >> > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 >> > > > >> > > > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in >> > > > qca_setup() is kinda ugly, but I think it's still better than the >> > > > conditional call of qca_read_soc_version() in qca_uart_setup(). >> > > >> > > [Bala]: we require an if-else block for soc type.As wcn3900 support >> > > hardware flow control where as ROME is not supporting hardware flow >> > > control. >> > >> > Since you mention if-else and flow control I'm not sure if you >> > understood correctly what I suggested. My suggestion is to add >> > something like this: >> > >> > if (qcadev->btsoc_type == QCA_ROME) { >> > ret = qca_read_soc_version(hdev, &soc_ver); >> > if (ret < 0 || soc_ver == 0) { >> > // Note mka@: we might want to skip this log, >> > // qca_read_soc_version() already logs in all error paths >> > bt_dev_err(hdev, "Failed to get version %d", ret); >> > return ret; >> > } >> > } >> > >> > right here: >> > >> > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 >> > >> > which is functionally equivalent to the current code. >> > >> > You could even do the error check in the common code (just checking >> > for 'soc_ver == 0', assuming that qca_read_soc_version() doesn't set >> > it to something different in case of error). >> > >> > Anyway, I won't insist if you prefer it as is and Marcel is ok with it. >> >> [Bala]: thanks for clarifying my doubt, but if remove the >> qca_read_soc_version() from qca_uart_setup() and handle it >> qca_setup(). >> in that case, we will have common blocks of code, when we >> integrate >> wcn3990 into existing qca_setup() > > Excellent! > >> static int qca_setup(struct hci_uart *hu) >> { >> ... >> >> qcadev = serdev_device_get_drvdata(hu->serdev); >> >> /* Patch downloading has to be done without IBS mode */ >> clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); >> >> /* Setup initial baudrate */ >> speed = qca_get_speed(hu, QCA_INIT_SPEED); >> if (speed) >> qca_set_speed(hu, speed, QCA_INIT_SPEED); > > I said earlier that a _set_speed() followed by a _get_speed() is a bit > odd, and that it would be better to get the speed first and pass it as > a parameter. After looking again over the larger code I'm not > convinced anymore this is such a good idea, since the above pattern is > repeated multiple times, when it could be just: > > qca_set_speed(hu, QCA_INIT_SPEED) > > (+ error handling, which is also missing in the code above) > > Just a thought, not asking you to change it back, do whatever seems > best to you. > >> if (qcadev->btsoc_type == QCA_WCN3990) { >> bt_dev_dbg(hdev, "setting up wcn3990"); >> hci_uart_set_flow_control(hu, true); >> ret = qca_send_vendor_cmd(hdev, >> QCA_WCN3990_POWERON_PULSE); >> if (ret) { >> bt_dev_err(hdev, "failed to send power on >> command"); >> return ret; >> } >> >> serdev_device_close(hu->serdev); >> ret = serdev_device_open(hu->serdev); >> if (ret) { >> bt_dev_err(hdev, "failed to open port"); >> return ret; >> } >> >> msleep(100); >> speed = qca_get_speed(hu, QCA_INIT_SPEED); >> if (speed) >> qca_set_speed(hu, speed, QCA_INIT_SPEED); >> >> hci_uart_set_flow_control(hu, false); >> } else { >> bt_dev_info(hdev, "ROME setup"); >> /* Setup user speed if needed */ >> speed = qca_get_speed(hu, QCA_OPER_SPEED); >> if (speed) { >> ret = qca_set_speed(hu, speed, >> QCA_OPER_SPEED); >> if (ret) >> return ret; >> >> qca_baudrate = qca_get_baudrate_value(speed); > > It seems setting 'qca_baudrate' could also be done in the common > path. Would require an extra qca_get_speed(hu, QCA_OPER_SPEED) call, > in exchange this would be done in a single place closer to where > 'qca_baudrate' is actually used. > > Actually as it is now 'qca_baudrate' could remain uninitialized for > Rome if no operating speed is defined, which judging from > qca_get_baudrate_value() should result in QCA_BAUDRATE_115200. > >> } >> } >> >> ret = qca_read_soc_version(hdev, &soc_ver); >> if (ret < 0 || soc_ver == 0) { >> bt_dev_err(hdev, "Failed to get version %d", ret); >> return ret; >> } >> bt_dev_info(hdev, "wcn3990 controller version 0x%08x", >> soc_ver); >> >> >> if (qcadev->btsoc_type == QCA_WCN3990) { >> hci_uart_set_flow_control(hu, true); >> /* Setup user speed if needed */ >> speed = qca_get_speed(hu, QCA_OPER_SPEED); >> if (speed) { >> ret = qca_set_speed(hu, speed, >> QCA_OPER_SPEED); >> if (ret) >> return ret; >> >> qca_baudrate = qca_get_baudrate_value(speed); >> >> } >> >> /* Setup patch / NVM configurations */ >> ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, >> soc_ver); >> if (!ret) { >> set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); >> qca_debugfs_init(hdev); >> } else if (ret == -ENOENT) { >> /* No patch/nvm-config found, run with original >> fw/config */ >> ret = 0; >> } else if (ret == -EAGAIN) { >> /* >> ... >> } > > Overall looks good and should still become a bit more compact if the > handling of flow control is done in _set_speed() as you suggested in > "[PATCH v7 8/8] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth > chip wcn3990" [Bala}: to over come calling qca_get_speed() for qca_baudrate. i prefer passing qca_baudrate as pointer argument to qca_set_speed(). that will actually helps to lower function calls. intern increase the speed of execution too. code snippet after integrating wcn3990: static int qca_set_speed(struct hci_uart *hu, unsigned int *qca_baudrate, enum qca_speed_type speed_type) { struct qca_serdev *qcadev; unsigned int speed; int ret; if (speed_type == QCA_INIT_SPEED) { speed = qca_get_speed(hu, QCA_INIT_SPEED); if (speed) { host_set_baudrate(hu, speed); *qca_baudrate = qca_get_baudrate_value(speed); } else { bt_dev_err(hu->hdev, "Init speed should be non zero"); } return 0; } speed = qca_get_speed(hu, QCA_OPER_SPEED); if (!speed) { bt_dev_err(hu->hdev, "operating speed should be non zero"); return 0; } qcadev = serdev_device_get_drvdata(hu->serdev); /* Disabling hardware flow control is preferred while * sending change baud rate command to SoC. */ if (qcadev->btsoc_type == QCA_WCN3990) hci_uart_set_flow_control(hu, true); *qca_baudrate = qca_get_baudrate_value(speed); bt_dev_info(hu->hdev, "Set UART speed to %d", speed); ret = qca_set_baudrate(hu->hdev, *qca_baudrate); if (ret) { bt_dev_err(hu->hdev, "Failed to change the baudrate (%d)", ret); return ret; } host_set_baudrate(hu, speed); if (qcadev->btsoc_type == QCA_WCN3990) hci_uart_set_flow_control(hu, false); return 0; } static int qca_setup(struct hci_uart *hu) { .... qcadev = serdev_device_get_drvdata(hu->serdev); /* Patch downloading has to be done without IBS mode */ clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); /* Setup initial baudrate */ qca_set_speed(hu, &qca_baudrate, QCA_INIT_SPEED); if (qcadev->btsoc_type == QCA_WCN3990) { bt_dev_dbg(hdev, "setting up wcn3990"); hci_uart_set_flow_control(hu, true); ret = qca_send_vendor_cmd(hdev, QCA_WCN3990_POWERON_PULSE); if (ret) return ret; serdev_device_close(hu->serdev); ret = serdev_device_open(hu->serdev); if (ret) { bt_dev_err(hdev, "failed to open port"); return ret; } msleep(100); /* Setup initial baudrate */ qca_set_speed(hu, &qca_baudrate, QCA_INIT_SPEED); hci_uart_set_flow_control(hu, false); ret = qca_read_soc_version(hdev, &soc_ver); if (ret < 0 || soc_ver == 0) { bt_dev_err(hdev, "Failed to get version %d", ret); return ret; } bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); } else { bt_dev_info(hdev, "ROME setup"); } /* Setup user speed if needed */ ret = qca_set_speed(hu, &qca_baudrate, QCA_OPER_SPEED); if (ret) return ret; /* Setup patch / NVM configurations */ ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, soc_ver); if (!ret) { set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); qca_debugfs_init(hdev); } else if (ret == -ENOENT) { /* No patch/nvm-config found, run with original fw/config */ ret = 0; } else if (ret == -EAGAIN) { /* * Userspace firmware loader will return -EAGAIN in case no * patch/nvm-config is found, so run with original fw/config. */ ret = 0; } /* Setup bdaddr */ hu->hdev->set_bdaddr = qca_set_bdaddr_rome; return ret; }
On Fri, Jun 22, 2018 at 08:41:01PM +0530, Balakrishna Godavarthi wrote: > Hi Matthias, > > On 2018-06-22 03:39, Matthias Kaehlcke wrote: > > On Thu, Jun 21, 2018 at 04:50:28PM +0530, Balakrishna Godavarthi wrote: > > > Hi Matthias, > > > > > > On 2018-06-21 05:03, Matthias Kaehlcke wrote: > > > > Hi Balakrishna, > > > > > > > > On Wed, Jun 20, 2018 at 04:23:25PM +0530, Balakrishna Godavarthi wrote: > > > > > Hi Matthias, > > > > > > > > > > On 2018-06-20 01:33, Matthias Kaehlcke wrote: > > > > > > On Tue, Jun 19, 2018 at 12:39:07PM +0530, Balakrishna Godavarthi wrote: > > > > > > > Hi Matthias, > > > > > > > > > > > > > > Please find my comments inline. > > > > > > > > > > > > > > On 2018-06-19 02:49, Matthias Kaehlcke wrote: > > > > > > > > On Sat, Jun 16, 2018 at 11:57:14AM +0530, Balakrishna Godavarthi wrote: > > > > > > > > > > > > > > > > > @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, > > > > > > > > > uint8_t baudrate) > > > > > > > > > > > > > > > > > > config.user_baud_rate = baudrate; > > > > > > > > > > > > > > > > > > - /* Get QCA version information */ > > > > > > > > > - err = qca_read_soc_version(hdev, &rome_ver); > > > > > > > > > - if (err < 0 || rome_ver == 0) { > > > > > > > > > - bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > > > > > - return err; > > > > > > > > > + if (!soc_ver) { > > > > > > > > > + /* Get QCA version information */ > > > > > > > > > + err = qca_read_soc_version(hdev, &soc_ver); > > > > > > > > > + if (err < 0 || soc_ver == 0) { > > > > > > > > > + bt_dev_err(hdev, "QCA Failed to get version %d", err); > > > > > > > > > + return err; > > > > > > > > > + } > > > > > > > > > + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); > > > > > > > > > } > > > > > > > > > > > > > > > > Why is this needed? A caller that passes in soc_ver = 0 could just > > > > > > > > call qca_read_soc_version() themselves. > > > > > > > [Bala]: hci_qca support two chip one ROME (already up-streamed) and > > > > > > > other > > > > > > > wcn3990. > > > > > > > there setup sequence differs. > > > > > > > > > > > > > > wcn3900: > > > > > > > 1. set baudrate to 115200 > > > > > > > 2. read soc version > > > > > > > 3. set baudarte to 3.2Mbps > > > > > > > 4. download firmware. (calls qca_uart_setup) > > > > > > > > > > > > > > ROME: > > > > > > > 1. set baudrate to 3.0 mbps > > > > > > > 2. calls qca_uart_setup to read soc version and download > > > > > > > firmware. > > > > > > > > > > > > > > so to make use of existing function qca_setup_uart(). passing > > > > > > > soc_ver > > > > > > > as argument. > > > > > > > if soc_ver is zero, then read soc version (i.e. for ROME chip). > > > > > > > > > > > > > > Pls let me know, if you have any queries. > > > > > > > > > > > > I don't really understand this argumentation. Let's look at the code > > > > > > at the end of this series, where both Rome and wcn3900 are supported: > > > > > > > > > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1059 > > > > > > > > > > > > The version could be read (for Rome only) after setting the operating > > > > > > speed: > > > > > > > > > > [Bala]: yes we can read SoC version after setting operating baud > > > > > rate. an > > > > > advice from SoC vendor that, read SoC version before setting operating > > > > > speed. > > > > > one advantage from reading SoC version before setting > > > > > operating > > > > > baudrate,it will helps us to understand whether the soc is > > > > > responding to any > > > > > commands in default baud rate > > > > > before setting operating speed. > > > > > > > > Is the recommendation for Rome or wcn3990? I was referring to Rome and > > > > the current code sets the operating speed and then reads the SoC > > > > version (inside qca_uart_setup()) > > > > > > > > > > [Bala]: my statement is wrt to wcn3990. yes, ROME will set operating > > > speed > > > and read version. > > > > > > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > > > > > > > > > > > I concede that having two "if (qcadev->btsoc_type == XYZ)" branches in > > > > > > qca_setup() is kinda ugly, but I think it's still better than the > > > > > > conditional call of qca_read_soc_version() in qca_uart_setup(). > > > > > > > > > > [Bala]: we require an if-else block for soc type.As wcn3900 support > > > > > hardware flow control where as ROME is not supporting hardware flow > > > > > control. > > > > > > > > Since you mention if-else and flow control I'm not sure if you > > > > understood correctly what I suggested. My suggestion is to add > > > > something like this: > > > > > > > > if (qcadev->btsoc_type == QCA_ROME) { > > > > ret = qca_read_soc_version(hdev, &soc_ver); > > > > if (ret < 0 || soc_ver == 0) { > > > > // Note mka@: we might want to skip this log, > > > > // qca_read_soc_version() already logs in all error paths > > > > bt_dev_err(hdev, "Failed to get version %d", ret); > > > > return ret; > > > > } > > > > } > > > > > > > > right here: > > > > > > > > https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/1045608/6/drivers/bluetooth/hci_qca.c#1111 > > > > > > > > which is functionally equivalent to the current code. > > > > > > > > You could even do the error check in the common code (just checking > > > > for 'soc_ver == 0', assuming that qca_read_soc_version() doesn't set > > > > it to something different in case of error). > > > > > > > > Anyway, I won't insist if you prefer it as is and Marcel is ok with it. > > > > > > [Bala]: thanks for clarifying my doubt, but if remove the > > > qca_read_soc_version() from qca_uart_setup() and handle it > > > qca_setup(). > > > in that case, we will have common blocks of code, when we > > > integrate > > > wcn3990 into existing qca_setup() > > > > Excellent! > > > > > static int qca_setup(struct hci_uart *hu) > > > { > > > ... > > > > > > qcadev = serdev_device_get_drvdata(hu->serdev); > > > > > > /* Patch downloading has to be done without IBS mode */ > > > clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > > > > > > /* Setup initial baudrate */ > > > speed = qca_get_speed(hu, QCA_INIT_SPEED); > > > if (speed) > > > qca_set_speed(hu, speed, QCA_INIT_SPEED); > > > > I said earlier that a _set_speed() followed by a _get_speed() is a bit > > odd, and that it would be better to get the speed first and pass it as > > a parameter. After looking again over the larger code I'm not > > convinced anymore this is such a good idea, since the above pattern is > > repeated multiple times, when it could be just: > > > > qca_set_speed(hu, QCA_INIT_SPEED) > > > > (+ error handling, which is also missing in the code above) > > > > Just a thought, not asking you to change it back, do whatever seems > > best to you. > > > > > if (qcadev->btsoc_type == QCA_WCN3990) { > > > bt_dev_dbg(hdev, "setting up wcn3990"); > > > hci_uart_set_flow_control(hu, true); > > > ret = qca_send_vendor_cmd(hdev, > > > QCA_WCN3990_POWERON_PULSE); > > > if (ret) { > > > bt_dev_err(hdev, "failed to send power on > > > command"); > > > return ret; > > > } > > > > > > serdev_device_close(hu->serdev); > > > ret = serdev_device_open(hu->serdev); > > > if (ret) { > > > bt_dev_err(hdev, "failed to open port"); > > > return ret; > > > } > > > > > > msleep(100); > > > speed = qca_get_speed(hu, QCA_INIT_SPEED); > > > if (speed) > > > qca_set_speed(hu, speed, QCA_INIT_SPEED); > > > > > > hci_uart_set_flow_control(hu, false); > > > } else { > > > bt_dev_info(hdev, "ROME setup"); > > > /* Setup user speed if needed */ > > > speed = qca_get_speed(hu, QCA_OPER_SPEED); > > > if (speed) { > > > ret = qca_set_speed(hu, speed, > > > QCA_OPER_SPEED); > > > if (ret) > > > return ret; > > > > > > qca_baudrate = qca_get_baudrate_value(speed); > > > > It seems setting 'qca_baudrate' could also be done in the common > > path. Would require an extra qca_get_speed(hu, QCA_OPER_SPEED) call, > > in exchange this would be done in a single place closer to where > > 'qca_baudrate' is actually used. > > > > Actually as it is now 'qca_baudrate' could remain uninitialized for > > Rome if no operating speed is defined, which judging from > > qca_get_baudrate_value() should result in QCA_BAUDRATE_115200. > > > > > } > > > } > > > > > > ret = qca_read_soc_version(hdev, &soc_ver); > > > if (ret < 0 || soc_ver == 0) { > > > bt_dev_err(hdev, "Failed to get version %d", ret); > > > return ret; > > > } > > > bt_dev_info(hdev, "wcn3990 controller version 0x%08x", > > > soc_ver); > > > > > > > > > if (qcadev->btsoc_type == QCA_WCN3990) { > > > hci_uart_set_flow_control(hu, true); > > > /* Setup user speed if needed */ > > > speed = qca_get_speed(hu, QCA_OPER_SPEED); > > > if (speed) { > > > ret = qca_set_speed(hu, speed, > > > QCA_OPER_SPEED); > > > if (ret) > > > return ret; > > > > > > qca_baudrate = qca_get_baudrate_value(speed); > > > > > > } > > > > > > /* Setup patch / NVM configurations */ > > > ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type, > > > soc_ver); > > > if (!ret) { > > > set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > > > qca_debugfs_init(hdev); > > > } else if (ret == -ENOENT) { > > > /* No patch/nvm-config found, run with original > > > fw/config */ > > > ret = 0; > > > } else if (ret == -EAGAIN) { > > > /* > > > ... > > > } > > > > Overall looks good and should still become a bit more compact if the > > handling of flow control is done in _set_speed() as you suggested in > > "[PATCH v7 8/8] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth > > chip wcn3990" > > [Bala}: to over come calling qca_get_speed() for qca_baudrate. > i prefer passing qca_baudrate as pointer argument to > qca_set_speed(). > that will actually helps to lower function calls. intern increase > the speed of execution too. I argued earlier against something similar, where speed was a pointer that was set inside _set_speed(). IMO this interface is unintuitive and makes the code harder to read, even if it saves a function call. The optimization isn't really an important factor here, _get_speed() is cheap and it isn't called in a hot code path. It's also an option to add an enum qca_speed_type parameter to qca_get_baudrate_value() and hide the _get_speed() call there. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c index c5cf9cab438a..f748730039cf 100644 --- a/drivers/bluetooth/btqca.c +++ b/drivers/bluetooth/btqca.c @@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr) } EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome); -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t soc_type, + u32 soc_ver) { - u32 rome_ver = 0; struct rome_config config; int err; @@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) config.user_baud_rate = baudrate; - /* Get QCA version information */ - err = qca_read_soc_version(hdev, &rome_ver); - if (err < 0 || rome_ver == 0) { - bt_dev_err(hdev, "QCA Failed to get version %d", err); - return err; + if (!soc_ver) { + /* Get QCA version information */ + err = qca_read_soc_version(hdev, &soc_ver); + if (err < 0 || soc_ver == 0) { + bt_dev_err(hdev, "QCA Failed to get version %d", err); + return err; + } + bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver); } - bt_dev_info(hdev, "QCA controller version 0x%08x", rome_ver); - /* Download rampatch file */ config.type = TLV_TYPE_PATCH; snprintf(config.fwname, sizeof(config.fwname), "qca/rampatch_%08x.bin", - rome_ver); + soc_ver); err = qca_download_firmware(hdev, &config); if (err < 0) { bt_dev_err(hdev, "QCA Failed to download patch (%d)", err); @@ -359,7 +360,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) /* Download NVM configuration */ config.type = TLV_TYPE_NVM; snprintf(config.fwname, sizeof(config.fwname), "qca/nvm_%08x.bin", - rome_ver); + soc_ver); err = qca_download_firmware(hdev, &config); if (err < 0) { bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err); diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h index d0ee96540636..c7a5d1754f47 100644 --- a/drivers/bluetooth/btqca.h +++ b/drivers/bluetooth/btqca.h @@ -124,10 +124,18 @@ struct tlv_type_hdr { __u8 data[0]; } __packed; +enum qca_btsoc_type { + QCA_INVALID = -1, + QCA_AR3002, + QCA_ROME, + QCA_WCN3990 +}; + #if IS_ENABLED(CONFIG_BT_QCA) int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr); -int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate); +int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, uint8_t soc_type, + u32 soc_ver); int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version); #else @@ -137,7 +145,8 @@ static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdad return -EOPNOTSUPP; } -static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate) +static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate, + uint8_t soc_type, u32 soc_ver) { return -EOPNOTSUPP; } diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c index d7b60669b656..fe62420ef838 100644 --- a/drivers/bluetooth/hci_qca.c +++ b/drivers/bluetooth/hci_qca.c @@ -929,6 +929,7 @@ static int qca_setup(struct hci_uart *hu) struct qca_data *qca = hu->priv; unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200; int ret; + int soc_ver = 0; bt_dev_info(hdev, "ROME setup"); @@ -966,7 +967,7 @@ static int qca_setup(struct hci_uart *hu) } /* Setup patch / NVM configurations */ - ret = qca_uart_setup(hdev, qca_baudrate); + ret = qca_uart_setup(hdev, qca_baudrate, QCA_ROME, soc_ver); if (!ret) { set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); qca_debugfs_init(hdev);
Redefinition of qca_uart_setup will help future Qualcomm Bluetooth SoC, to use the same function instead of duplicating the function. Added new arguments soc_type and soc_ver to the functions. These arguments will help to decide type of firmware files to be loaded into Bluetooth chip. soc_type holds the Bluetooth chip connected to APPS processor. soc_ver holds the Bluetooth chip version. Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> --- Changes in v7: * initial patch * redefined qca_uart_setup function to generic. --- drivers/bluetooth/btqca.c | 23 ++++++++++++----------- drivers/bluetooth/btqca.h | 13 +++++++++++-- drivers/bluetooth/hci_qca.c | 3 ++- 3 files changed, 25 insertions(+), 14 deletions(-)