| Message ID | 20181128132554.28139-1-stefan@agner.ch (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
| Series | pci: imx6: support kernels built in Thumb-2 mode | expand |
Hi Stefan, On 28/11/2018 13:25, Stefan Agner wrote: > Add a fault handler which handles reads in Thumb-2 mode. Install > the appropriate handler depending on which mode the kernel has > been built. This avoids an "Unhandled fault: external abort on > non-linefetch (0x1008) at 0xf0a80000" during boot on a device > with a PCIe switch connected. > > Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ > Signed-off-by: Stefan Agner <stefan@agner.ch> > --- > FWIW, I found this manual helpful to write the code below: > http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 This one's rather less ancient and even more authoritative ;) https://static.docs.arm.com/ddi0406/cd/DDI0406C_d_armv7ar_arm.pdf (ARMv7 had a few new encodings over and above ARMv6T2, although in fairness I don't think any should be relevant to this specific case) > -- > Stefan > > drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- > 1 file changed, 36 insertions(+), 1 deletion(-) > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c > index 69f86234f7c0..683deb74d69f 100644 > --- a/drivers/pci/controller/dwc/pci-imx6.c > +++ b/drivers/pci/controller/dwc/pci-imx6.c > @@ -29,6 +29,7 @@ > #include <linux/reset.h> > #include <linux/pm_domain.h> > #include <linux/pm_runtime.h> > +#include <asm/opcodes.h> > > #include "pcie-designware.h" > > @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, > return 1; > } > > +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, > + unsigned int fsr, struct pt_regs *regs) > +{ > + unsigned long pc = instruction_pointer(regs); > + unsigned long instr = *(unsigned long *)pc; > + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); > + int reg = thumb2_instr & 7; > + > + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) > + return 1; There are plenty of 32-bit Thumb encodings of various LDR/STR variants, and I doubt we can guarantee that the offset, target register, and/or addressing mode for a config space access will *always* suit the (relatively limited) 16-bit ones. > + > + /* Load word/byte and halfword immediate offset */ > + if (((thumb2_instr & 0xe800) == 0x6800) || > + ((thumb2_instr & 0xf800) == 0x8800)) { > + unsigned long val; > + > + if (thumb2_instr & 0x1000) > + val = 0xff; > + else if (thumb2_instr & 0x8000) > + val = 0xffff; > + else > + val = 0xffffffffUL; > + > + regs->uregs[reg] = val; > + regs->ARM_pc += 2; > + return 0; > + } What about stores? The existing implementation handles them, so either that's dead code which could perhaps be cleaned up, or they need to be handled here too. > + > + return 1; > +} > + > static int imx6_pcie_attach_pd(struct device *dev) > { > struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); > @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { > > static int __init imx6_pcie_init(void) > { > + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); Can these aborts definitely *only* be triggered by kernel accesses, and never, say, via an mmap() of anything exposed to userspace? Robin. > + > /* > * Since probe() can be deferred we need to make sure that > * hook_fault_code is not called after __init memory is freed > @@ -1076,7 +1110,8 @@ static int __init imx6_pcie_init(void) > * we can install the handler here without risking it > * accessing some uninitialized driver state. > */ > - hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, > + hook_fault_code(8, thumb2 ? imx6q_pcie_abort_handler_thumb2 : > + imx6q_pcie_abort_handler, SIGBUS, 0, > "external abort on non-linefetch"); > > return platform_driver_register(&imx6_pcie_driver); >
On 28.11.2018 17:16, Robin Murphy wrote: > Hi Stefan, > > On 28/11/2018 13:25, Stefan Agner wrote: >> Add a fault handler which handles reads in Thumb-2 mode. Install >> the appropriate handler depending on which mode the kernel has >> been built. This avoids an "Unhandled fault: external abort on >> non-linefetch (0x1008) at 0xf0a80000" during boot on a device >> with a PCIe switch connected. >> >> Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ >> Signed-off-by: Stefan Agner <stefan@agner.ch> >> --- >> FWIW, I found this manual helpful to write the code below: >> http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 > > This one's rather less ancient and even more authoritative ;) > > https://static.docs.arm.com/ddi0406/cd/DDI0406C_d_armv7ar_arm.pdf > > (ARMv7 had a few new encodings over and above ARMv6T2, although in > fairness I don't think any should be relevant to this specific case) > Thanks, I tried to find the right document on arm.com, but I timed out after 5 minutes or so :-) >> -- >> Stefan >> >> drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- >> 1 file changed, 36 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c >> index 69f86234f7c0..683deb74d69f 100644 >> --- a/drivers/pci/controller/dwc/pci-imx6.c >> +++ b/drivers/pci/controller/dwc/pci-imx6.c >> @@ -29,6 +29,7 @@ >> #include <linux/reset.h> >> #include <linux/pm_domain.h> >> #include <linux/pm_runtime.h> >> +#include <asm/opcodes.h> >> #include "pcie-designware.h" >> @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, >> return 1; >> } >> +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, >> + unsigned int fsr, struct pt_regs *regs) >> +{ >> + unsigned long pc = instruction_pointer(regs); >> + unsigned long instr = *(unsigned long *)pc; >> + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); >> + int reg = thumb2_instr & 7; >> + >> + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) >> + return 1; > > There are plenty of 32-bit Thumb encodings of various LDR/STR > variants, and I doubt we can guarantee that the offset, target > register, and/or addressing mode for a config space access will > *always* suit the (relatively limited) 16-bit ones. Hm, I guess they should be handled too? I looked at the code where I had the abort at hand triggered (dw_pcie_read). >> + >> + /* Load word/byte and halfword immediate offset */ >> + if (((thumb2_instr & 0xe800) == 0x6800) || >> + ((thumb2_instr & 0xf800) == 0x8800)) { >> + unsigned long val; >> + >> + if (thumb2_instr & 0x1000) >> + val = 0xff; >> + else if (thumb2_instr & 0x8000) >> + val = 0xffff; >> + else >> + val = 0xffffffffUL; >> + >> + regs->uregs[reg] = val; >> + regs->ARM_pc += 2; >> + return 0; >> + } > > What about stores? The existing implementation handles them, so either > that's dead code which could perhaps be cleaned up, or they need to be > handled here too. > I think the current handler (imx6q_pcie_abort_handler) checks bit 20, which means it must be a load not? >> + >> + return 1; >> +} >> + >> static int imx6_pcie_attach_pd(struct device *dev) >> { >> struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); >> @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { >> static int __init imx6_pcie_init(void) >> { >> + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); > > Can these aborts definitely *only* be triggered by kernel accesses, > and never, say, via an mmap() of anything exposed to userspace? Honestly, I am not very familiar with PCIe, I don't know... -- Stefan > > Robin. > >> + >> /* >> * Since probe() can be deferred we need to make sure that >> * hook_fault_code is not called after __init memory is freed >> @@ -1076,7 +1110,8 @@ static int __init imx6_pcie_init(void) >> * we can install the handler here without risking it >> * accessing some uninitialized driver state. >> */ >> - hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, >> + hook_fault_code(8, thumb2 ? imx6q_pcie_abort_handler_thumb2 : >> + imx6q_pcie_abort_handler, SIGBUS, 0, >> "external abort on non-linefetch"); >> return platform_driver_register(&imx6_pcie_driver); >>
On Wed, Nov 28, 2018 at 02:25:54PM +0100, Stefan Agner wrote: > Add a fault handler which handles reads in Thumb-2 mode. Install > the appropriate handler depending on which mode the kernel has > been built. This avoids an "Unhandled fault: external abort on > non-linefetch (0x1008) at 0xf0a80000" during boot on a device > with a PCIe switch connected. > > Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ > Signed-off-by: Stefan Agner <stefan@agner.ch> > --- > FWIW, I found this manual helpful to write the code below: > http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 > > -- > Stefan > > drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- > 1 file changed, 36 insertions(+), 1 deletion(-) > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c > index 69f86234f7c0..683deb74d69f 100644 > --- a/drivers/pci/controller/dwc/pci-imx6.c > +++ b/drivers/pci/controller/dwc/pci-imx6.c > @@ -29,6 +29,7 @@ > #include <linux/reset.h> > #include <linux/pm_domain.h> > #include <linux/pm_runtime.h> > +#include <asm/opcodes.h> > > #include "pcie-designware.h" > > @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, > return 1; > } > > +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, > + unsigned int fsr, struct pt_regs *regs) > +{ > + unsigned long pc = instruction_pointer(regs); > + unsigned long instr = *(unsigned long *)pc; So what happens if userspace mmap()s the PCIe space (eg, via /dev/mem), and then accesses it, triggering this fault? You'll be attempting to read from userspace here, which will oops the kernel. The kernel is not allowed to access userspace by simply dereferencing a pointer. > + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); > + int reg = thumb2_instr & 7; > + > + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) > + return 1; > + > + /* Load word/byte and halfword immediate offset */ > + if (((thumb2_instr & 0xe800) == 0x6800) || > + ((thumb2_instr & 0xf800) == 0x8800)) { > + unsigned long val; > + > + if (thumb2_instr & 0x1000) > + val = 0xff; > + else if (thumb2_instr & 0x8000) > + val = 0xffff; > + else > + val = 0xffffffffUL; > + > + regs->uregs[reg] = val; > + regs->ARM_pc += 2; > + return 0; > + } > + > + return 1; > +} > + > static int imx6_pcie_attach_pd(struct device *dev) > { > struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); > @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { > > static int __init imx6_pcie_init(void) > { > + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); > + > /* > * Since probe() can be deferred we need to make sure that > * hook_fault_code is not called after __init memory is freed > @@ -1076,7 +1110,8 @@ static int __init imx6_pcie_init(void) > * we can install the handler here without risking it > * accessing some uninitialized driver state. > */ > - hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, > + hook_fault_code(8, thumb2 ? imx6q_pcie_abort_handler_thumb2 : > + imx6q_pcie_abort_handler, SIGBUS, 0, > "external abort on non-linefetch"); > > return platform_driver_register(&imx6_pcie_driver); > -- > 2.19.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Wed, 2018-11-28 at 16:16 +0000, Robin Murphy wrote: > > > > > +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, > > + unsigned int fsr, struct pt_regs *regs) > > +{ > > + unsigned long pc = instruction_pointer(regs); > > + unsigned long instr = *(unsigned long *)pc; > > + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); > > + int reg = thumb2_instr & 7; > > + > > + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) > > + return 1; > > There are plenty of 32-bit Thumb encodings of various LDR/STR variants, > and I doubt we can guarantee that the offset, target register, and/or > addressing mode for a config space access will *always* suit the > (relatively limited) 16-bit ones. It might be the case that PLD/PLI, 32-bit thumb2 instructions, could trigger an abort too.
On 28/11/2018 17:53, Stefan Agner wrote: > On 28.11.2018 17:16, Robin Murphy wrote: >> Hi Stefan, >> >> On 28/11/2018 13:25, Stefan Agner wrote: >>> Add a fault handler which handles reads in Thumb-2 mode. Install >>> the appropriate handler depending on which mode the kernel has >>> been built. This avoids an "Unhandled fault: external abort on >>> non-linefetch (0x1008) at 0xf0a80000" during boot on a device >>> with a PCIe switch connected. >>> >>> Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ >>> Signed-off-by: Stefan Agner <stefan@agner.ch> >>> --- >>> FWIW, I found this manual helpful to write the code below: >>> http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 >> >> This one's rather less ancient and even more authoritative ;) >> >> https://static.docs.arm.com/ddi0406/cd/DDI0406C_d_armv7ar_arm.pdf >> >> (ARMv7 had a few new encodings over and above ARMv6T2, although in >> fairness I don't think any should be relevant to this specific case) >> > > Thanks, I tried to find the right document on arm.com, but I timed out > after 5 minutes or so :-) > >>> -- >>> Stefan >>> >>> drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- >>> 1 file changed, 36 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c >>> index 69f86234f7c0..683deb74d69f 100644 >>> --- a/drivers/pci/controller/dwc/pci-imx6.c >>> +++ b/drivers/pci/controller/dwc/pci-imx6.c >>> @@ -29,6 +29,7 @@ >>> #include <linux/reset.h> >>> #include <linux/pm_domain.h> >>> #include <linux/pm_runtime.h> >>> +#include <asm/opcodes.h> >>> #include "pcie-designware.h" >>> @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, >>> return 1; >>> } >>> +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, >>> + unsigned int fsr, struct pt_regs *regs) >>> +{ >>> + unsigned long pc = instruction_pointer(regs); >>> + unsigned long instr = *(unsigned long *)pc; >>> + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); >>> + int reg = thumb2_instr & 7; >>> + >>> + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) >>> + return 1; >> >> There are plenty of 32-bit Thumb encodings of various LDR/STR >> variants, and I doubt we can guarantee that the offset, target >> register, and/or addressing mode for a config space access will >> *always* suit the (relatively limited) 16-bit ones. > > Hm, I guess they should be handled too? > > I looked at the code where I had the abort at hand triggered > (dw_pcie_read). For the sake of robustness, I think it makes sense to at least handle all LDR/LDRH/LDRB encodings which might possibly fall out of a read[lwb]() call. Given that we seem to have various versions of this decoding in differing states of completeness, perhaps it's even worth factoring out into some kind of common "Arm PCI synchronous abort handler". >>> + >>> + /* Load word/byte and halfword immediate offset */ >>> + if (((thumb2_instr & 0xe800) == 0x6800) || >>> + ((thumb2_instr & 0xf800) == 0x8800)) { >>> + unsigned long val; >>> + >>> + if (thumb2_instr & 0x1000) >>> + val = 0xff; >>> + else if (thumb2_instr & 0x8000) >>> + val = 0xffff; >>> + else >>> + val = 0xffffffffUL; >>> + >>> + regs->uregs[reg] = val; >>> + regs->ARM_pc += 2; >>> + return 0; >>> + } >> >> What about stores? The existing implementation handles them, so either >> that's dead code which could perhaps be cleaned up, or they need to be >> handled here too. >> > > I think the current handler (imx6q_pcie_abort_handler) checks bit 20, > which means it must be a load not? Oops, that's just me being dumb - I managed to overlook the pt_regs assignment in the second if() block and thought it was just advancing the PC, so assumed (because I also didn't bother to actually look up the relevant encoding bits) it must be handling stores. Never mind that part then. >>> + >>> + return 1; >>> +} >>> + >>> static int imx6_pcie_attach_pd(struct device *dev) >>> { >>> struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); >>> @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { >>> static int __init imx6_pcie_init(void) >>> { >>> + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); >> >> Can these aborts definitely *only* be triggered by kernel accesses, >> and never, say, via an mmap() of anything exposed to userspace? > > Honestly, I am not very familiar with PCIe, I don't know... Yeah, hopefully the linux-pci audience can clear up that one. I was thinking in terms of whether we might need a combined handler with a runtime "thumb_mode(regs)" check rather than a compile-time decision, but Russell has a good point that just reading the instruction at all is its own can of worms in that case. Robin.
On 28/11/2018 18:56, Trent Piepho wrote: > On Wed, 2018-11-28 at 16:16 +0000, Robin Murphy wrote: >> >>> >>> +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, >>> + unsigned int fsr, struct pt_regs *regs) >>> +{ >>> + unsigned long pc = instruction_pointer(regs); >>> + unsigned long instr = *(unsigned long *)pc; >>> + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); >>> + int reg = thumb2_instr & 7; >>> + >>> + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) >>> + return 1; >> >> There are plenty of 32-bit Thumb encodings of various LDR/STR variants, >> and I doubt we can guarantee that the offset, target register, and/or >> addressing mode for a config space access will *always* suit the >> (relatively limited) 16-bit ones. > > It might be the case that PLD/PLI, 32-bit thumb2 instructions, could > trigger an abort too. Preload instructions shouldn't cause a *synchronous* abort, which is what we're trapping here, and they could only result in an asynchronous abort coming back later if the address is mapped as Normal memory, which it really shouldn't be in this case. Frankly either way, anyone even thinking about trying to pull PCI config space into data caches, let alone instruction caches, probably deserves everything they get ;) Robin.
On Wed, 2018-11-28 at 19:52 +0000, Robin Murphy wrote: > On 28/11/2018 18:56, Trent Piepho wrote: > > On Wed, 2018-11-28 at 16:16 +0000, Robin Murphy wrote: > > > > > > > > > > > +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, > > > > + unsigned int fsr, struct pt_regs *regs) > > > > +{ > > > > + unsigned long pc = instruction_pointer(regs); > > > > + unsigned long instr = *(unsigned long *)pc; > > > > + unsigned long thumb2_instr = > > > > __mem_to_opcode_thumb16(instr); > > > > + int reg = thumb2_instr & 7; > > > > + > > > > + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) > > > > + return 1; > > > > > > There are plenty of 32-bit Thumb encodings of various LDR/STR > > > variants, > > > and I doubt we can guarantee that the offset, target register, > > > and/or > > > addressing mode for a config space access will *always* suit the > > > (relatively limited) 16-bit ones. > > > > It might be the case that PLD/PLI, 32-bit thumb2 instructions, > > could > > trigger an abort too. > > Preload instructions shouldn't cause a *synchronous* abort, which is > what we're trapping here, and they could only result in an asynchronous > abort coming back later if the address is mapped as Normal memory, which > it really shouldn't be in this case. Frankly either way, anyone even > thinking about trying to pull PCI config space into data caches, let > alone instruction caches, probably deserves everything they get ;) It would be easy to do from userspace. mmap the config space attribute in sysfs, and then call plain old glibc memcpy() on it to copy to normal ram. strlen(), memcpy(), etc. are coded with pld instructions.
On 28.11.2018 19:01, Russell King - ARM Linux wrote: > On Wed, Nov 28, 2018 at 02:25:54PM +0100, Stefan Agner wrote: >> Add a fault handler which handles reads in Thumb-2 mode. Install >> the appropriate handler depending on which mode the kernel has >> been built. This avoids an "Unhandled fault: external abort on >> non-linefetch (0x1008) at 0xf0a80000" during boot on a device >> with a PCIe switch connected. >> >> Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ >> Signed-off-by: Stefan Agner <stefan@agner.ch> >> --- >> FWIW, I found this manual helpful to write the code below: >> http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 >> >> -- >> Stefan >> >> drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- >> 1 file changed, 36 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c >> index 69f86234f7c0..683deb74d69f 100644 >> --- a/drivers/pci/controller/dwc/pci-imx6.c >> +++ b/drivers/pci/controller/dwc/pci-imx6.c >> @@ -29,6 +29,7 @@ >> #include <linux/reset.h> >> #include <linux/pm_domain.h> >> #include <linux/pm_runtime.h> >> +#include <asm/opcodes.h> >> >> #include "pcie-designware.h" >> >> @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, >> return 1; >> } >> >> +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, >> + unsigned int fsr, struct pt_regs *regs) >> +{ >> + unsigned long pc = instruction_pointer(regs); >> + unsigned long instr = *(unsigned long *)pc; > > So what happens if userspace mmap()s the PCIe space (eg, via > /dev/mem), and then accesses it, triggering this fault? You'll > be attempting to read from userspace here, which will oops the > kernel. The kernel is not allowed to access userspace by > simply dereferencing a pointer. > Note that imx6q_pcie_abort_handler above does the same for ARM code. I guess a quick fix for now would be just using user_mode before dereferencing the pc: if (user_mode(regs)) return 1; Is userspace mmap'ing PCIe space common? If we want to support user space, I guess we anyway should merge the ARM and Thumb2 handler, and detect & act accordingly. -- Stefan >> + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); >> + int reg = thumb2_instr & 7; >> + >> + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) >> + return 1; >> + >> + /* Load word/byte and halfword immediate offset */ >> + if (((thumb2_instr & 0xe800) == 0x6800) || >> + ((thumb2_instr & 0xf800) == 0x8800)) { >> + unsigned long val; >> + >> + if (thumb2_instr & 0x1000) >> + val = 0xff; >> + else if (thumb2_instr & 0x8000) >> + val = 0xffff; >> + else >> + val = 0xffffffffUL; >> + >> + regs->uregs[reg] = val; >> + regs->ARM_pc += 2; >> + return 0; >> + } >> + >> + return 1; >> +} >> + >> static int imx6_pcie_attach_pd(struct device *dev) >> { >> struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); >> @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { >> >> static int __init imx6_pcie_init(void) >> { >> + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); >> + >> /* >> * Since probe() can be deferred we need to make sure that >> * hook_fault_code is not called after __init memory is freed >> @@ -1076,7 +1110,8 @@ static int __init imx6_pcie_init(void) >> * we can install the handler here without risking it >> * accessing some uninitialized driver state. >> */ >> - hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, >> + hook_fault_code(8, thumb2 ? imx6q_pcie_abort_handler_thumb2 : >> + imx6q_pcie_abort_handler, SIGBUS, 0, >> "external abort on non-linefetch"); >> >> return platform_driver_register(&imx6_pcie_driver); >> -- >> 2.19.1 >> >> >> _______________________________________________ >> linux-arm-kernel mailing list >> linux-arm-kernel@lists.infradead.org >> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On 28.11.2018 20:35, Robin Murphy wrote: > On 28/11/2018 17:53, Stefan Agner wrote: >> On 28.11.2018 17:16, Robin Murphy wrote: >>> Hi Stefan, >>> >>> On 28/11/2018 13:25, Stefan Agner wrote: >>>> Add a fault handler which handles reads in Thumb-2 mode. Install >>>> the appropriate handler depending on which mode the kernel has >>>> been built. This avoids an "Unhandled fault: external abort on >>>> non-linefetch (0x1008) at 0xf0a80000" during boot on a device >>>> with a PCIe switch connected. >>>> >>>> Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ >>>> Signed-off-by: Stefan Agner <stefan@agner.ch> >>>> --- >>>> FWIW, I found this manual helpful to write the code below: >>>> http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 >>> >>> This one's rather less ancient and even more authoritative ;) >>> >>> https://static.docs.arm.com/ddi0406/cd/DDI0406C_d_armv7ar_arm.pdf >>> >>> (ARMv7 had a few new encodings over and above ARMv6T2, although in >>> fairness I don't think any should be relevant to this specific case) >>> >> >> Thanks, I tried to find the right document on arm.com, but I timed out >> after 5 minutes or so :-) >> >>>> -- >>>> Stefan >>>> >>>> drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- >>>> 1 file changed, 36 insertions(+), 1 deletion(-) >>>> >>>> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c >>>> index 69f86234f7c0..683deb74d69f 100644 >>>> --- a/drivers/pci/controller/dwc/pci-imx6.c >>>> +++ b/drivers/pci/controller/dwc/pci-imx6.c >>>> @@ -29,6 +29,7 @@ >>>> #include <linux/reset.h> >>>> #include <linux/pm_domain.h> >>>> #include <linux/pm_runtime.h> >>>> +#include <asm/opcodes.h> >>>> #include "pcie-designware.h" >>>> @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, >>>> return 1; >>>> } >>>> +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, >>>> + unsigned int fsr, struct pt_regs *regs) >>>> +{ >>>> + unsigned long pc = instruction_pointer(regs); >>>> + unsigned long instr = *(unsigned long *)pc; >>>> + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); >>>> + int reg = thumb2_instr & 7; >>>> + >>>> + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) >>>> + return 1; >>> >>> There are plenty of 32-bit Thumb encodings of various LDR/STR >>> variants, and I doubt we can guarantee that the offset, target >>> register, and/or addressing mode for a config space access will >>> *always* suit the (relatively limited) 16-bit ones. >> >> Hm, I guess they should be handled too? >> >> I looked at the code where I had the abort at hand triggered >> (dw_pcie_read). > > For the sake of robustness, I think it makes sense to at least handle > all LDR/LDRH/LDRB encodings which might possibly fall out of a > read[lwb]() call. Given that we seem to have various versions of this > decoding in differing states of completeness, perhaps it's even worth > factoring out into some kind of common "Arm PCI synchronous abort > handler". > That was actually my approach. dw_pcie_read uses read[lwb](), and this is how it disassembles: 00000000 <dw_pcie_read>: 0: 1e4b subs r3, r1, #1 2: 4003 ands r3, r0 4: d112 bne.n 2c <dw_pcie_read+0x2c> 6: 2904 cmp r1, #4 8: d00a beq.n 20 <dw_pcie_read+0x20> a: 2902 cmp r1, #2 c: d012 beq.n 34 <dw_pcie_read+0x34> e: 2901 cmp r1, #1 10: d10c bne.n 2c <dw_pcie_read+0x2c> 12: 7801 ldrb r1, [r0, #0] 14: b2c9 uxtb r1, r1 16: f3bf 8f4f dsb sy 1a: 4618 mov r0, r3 1c: 6011 str r1, [r2, #0] 1e: 4770 bx lr 20: 6801 ldr r1, [r0, #0] 22: f3bf 8f4f dsb sy 26: 6011 str r1, [r2, #0] 28: 4618 mov r0, r3 2a: 4770 bx lr 2c: 2300 movs r3, #0 2e: 2087 movs r0, #135 ; 0x87 30: 6013 str r3, [r2, #0] 32: 4770 bx lr 34: 8801 ldrh r1, [r0, #0] 36: b289 uxth r1, r1 38: f3bf 8f4f dsb sy 3c: 6011 str r1, [r2, #0] 3e: 4618 mov r0, r3 40: 4770 bx lr 42: bf00 nop Those three loads should be handled by below code (unless I made a mistake). >>>> + >>>> + /* Load word/byte and halfword immediate offset */ >>>> + if (((thumb2_instr & 0xe800) == 0x6800) || >>>> + ((thumb2_instr & 0xf800) == 0x8800)) { >>>> + unsigned long val; >>>> + >>>> + if (thumb2_instr & 0x1000) >>>> + val = 0xff; >>>> + else if (thumb2_instr & 0x8000) >>>> + val = 0xffff; >>>> + else >>>> + val = 0xffffffffUL; >>>> + >>>> + regs->uregs[reg] = val; >>>> + regs->ARM_pc += 2; >>>> + return 0; >>>> + } >>> >>> What about stores? The existing implementation handles them, so either >>> that's dead code which could perhaps be cleaned up, or they need to be >>> handled here too. >>> >> >> I think the current handler (imx6q_pcie_abort_handler) checks bit 20, >> which means it must be a load not? > > Oops, that's just me being dumb - I managed to overlook the pt_regs > assignment in the second if() block and thought it was just advancing > the PC, so assumed (because I also didn't bother to actually look up > the relevant encoding bits) it must be handling stores. Never mind > that part then. > >>>> + >>>> + return 1; >>>> +} >>>> + >>>> static int imx6_pcie_attach_pd(struct device *dev) >>>> { >>>> struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); >>>> @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { >>>> static int __init imx6_pcie_init(void) >>>> { >>>> + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); >>> >>> Can these aborts definitely *only* be triggered by kernel accesses, >>> and never, say, via an mmap() of anything exposed to userspace? >> >> Honestly, I am not very familiar with PCIe, I don't know... > > Yeah, hopefully the linux-pci audience can clear up that one. > > I was thinking in terms of whether we might need a combined handler > with a runtime "thumb_mode(regs)" check rather than a compile-time > decision, but Russell has a good point that just reading the > instruction at all is its own can of worms in that case. Since the ARM handler also does not support userspace at this point I'd rather prefer to just exclude that case and pass it to the default handler. Then we can look at it once a real world case comes up... -- Stefan > > Robin.
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c index 69f86234f7c0..683deb74d69f 100644 --- a/drivers/pci/controller/dwc/pci-imx6.c +++ b/drivers/pci/controller/dwc/pci-imx6.c @@ -29,6 +29,7 @@ #include <linux/reset.h> #include <linux/pm_domain.h> #include <linux/pm_runtime.h> +#include <asm/opcodes.h> #include "pcie-designware.h" @@ -299,6 +300,37 @@ static int imx6q_pcie_abort_handler(unsigned long addr, return 1; } +static int imx6q_pcie_abort_handler_thumb2(unsigned long addr, + unsigned int fsr, struct pt_regs *regs) +{ + unsigned long pc = instruction_pointer(regs); + unsigned long instr = *(unsigned long *)pc; + unsigned long thumb2_instr = __mem_to_opcode_thumb16(instr); + int reg = thumb2_instr & 7; + + if (!__opcode_is_thumb16(instr & 0x0000ffffUL)) + return 1; + + /* Load word/byte and halfword immediate offset */ + if (((thumb2_instr & 0xe800) == 0x6800) || + ((thumb2_instr & 0xf800) == 0x8800)) { + unsigned long val; + + if (thumb2_instr & 0x1000) + val = 0xff; + else if (thumb2_instr & 0x8000) + val = 0xffff; + else + val = 0xffffffffUL; + + regs->uregs[reg] = val; + regs->ARM_pc += 2; + return 0; + } + + return 1; +} + static int imx6_pcie_attach_pd(struct device *dev) { struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); @@ -1069,6 +1101,8 @@ static struct platform_driver imx6_pcie_driver = { static int __init imx6_pcie_init(void) { + bool thumb2 = IS_ENABLED(CONFIG_THUMB2_KERNEL); + /* * Since probe() can be deferred we need to make sure that * hook_fault_code is not called after __init memory is freed @@ -1076,7 +1110,8 @@ static int __init imx6_pcie_init(void) * we can install the handler here without risking it * accessing some uninitialized driver state. */ - hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0, + hook_fault_code(8, thumb2 ? imx6q_pcie_abort_handler_thumb2 : + imx6q_pcie_abort_handler, SIGBUS, 0, "external abort on non-linefetch"); return platform_driver_register(&imx6_pcie_driver);
Add a fault handler which handles reads in Thumb-2 mode. Install the appropriate handler depending on which mode the kernel has been built. This avoids an "Unhandled fault: external abort on non-linefetch (0x1008) at 0xf0a80000" during boot on a device with a PCIe switch connected. Link: https://lore.kernel.org/linux-pci/20181126161645.8177-1-stefan@agner.ch/ Signed-off-by: Stefan Agner <stefan@agner.ch> --- FWIW, I found this manual helpful to write the code below: http://hermes.wings.cs.wisc.edu/files/Thumb-2SupplementReferenceManual.pdf#page=43&zoom=100,0,66 -- Stefan drivers/pci/controller/dwc/pci-imx6.c | 37 ++++++++++++++++++++++++++- 1 file changed, 36 insertions(+), 1 deletion(-)