| Message ID | 20190128060840.31695-2-angus@akkea.ca (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | dmaengine: imx-sdma: add the sdma engine to the imx8mq | expand |
Am Sonntag, den 27.01.2019, 23:08 -0700 schrieb Angus Ainslie (Purism): > On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted, > since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach > to 500Mhz, so use 1:1 instead. > > Based on NXP commit MLK-16841-1 by Robin Gong <yibin.gong@nxp.com> > > Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > --- > drivers/dma/imx-sdma.c | 18 ++++++++++++++---- > 1 file changed, 14 insertions(+), 4 deletions(-) > > diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c > index 0b3a67ff8e82..757fad2fbfae 100644 > --- a/drivers/dma/imx-sdma.c > +++ b/drivers/dma/imx-sdma.c > @@ -440,6 +440,8 @@ struct sdma_engine { > unsigned int irq; > dma_addr_t bd0_phys; > struct sdma_buffer_descriptor *bd0; > + /* clock ratio for AHB:SDMA core. 1:1 is 1, 2:1 is 0*/ > + bool clk_ratio; > }; > > static int sdma_config_write(struct dma_chan *chan, > @@ -662,8 +664,11 @@ static int sdma_run_channel0(struct sdma_engine *sdma) > dev_err(sdma->dev, "Timeout waiting for CH0 ready\n"); > > /* Set bits of CONFIG register with dynamic context switching */ > - if (readl(sdma->regs + SDMA_H_CONFIG) == 0) > - writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG); > + reg = readl(sdma->regs + SDMA_H_CONFIG); > + if ((reg & SDMA_H_CONFIG_CSM) == 0) { > + reg |= SDMA_H_CONFIG_CSM; > + writel_relaxed(reg, sdma->regs + SDMA_H_CONFIG); > + } > > return ret; > } > @@ -1840,6 +1845,9 @@ static int sdma_init(struct sdma_engine *sdma) > if (ret) > goto disable_clk_ipg; > > + if (clk_get_rate(sdma->clk_ahb) == clk_get_rate(sdma->clk_ipg)) > + sdma->clk_ratio = 1; > + > /* Be sure SDMA has not started yet */ > writel_relaxed(0, sdma->regs + SDMA_H_C0PTR); > > @@ -1880,8 +1888,10 @@ static int sdma_init(struct sdma_engine *sdma) > writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR); > > /* Set bits of CONFIG register but with static context switching */ > - /* FIXME: Check whether to set ACR bit depending on clock ratios */ > - writel_relaxed(0, sdma->regs + SDMA_H_CONFIG); > + if (sdma->clk_ratio) > + writel_relaxed(SDMA_H_CONFIG_ACR, sdma->regs + SDMA_H_CONFIG); > + else > + writel_relaxed(0, sdma->regs + SDMA_H_CONFIG); > > writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR); >
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c index 0b3a67ff8e82..757fad2fbfae 100644 --- a/drivers/dma/imx-sdma.c +++ b/drivers/dma/imx-sdma.c @@ -440,6 +440,8 @@ struct sdma_engine { unsigned int irq; dma_addr_t bd0_phys; struct sdma_buffer_descriptor *bd0; + /* clock ratio for AHB:SDMA core. 1:1 is 1, 2:1 is 0*/ + bool clk_ratio; }; static int sdma_config_write(struct dma_chan *chan, @@ -662,8 +664,11 @@ static int sdma_run_channel0(struct sdma_engine *sdma) dev_err(sdma->dev, "Timeout waiting for CH0 ready\n"); /* Set bits of CONFIG register with dynamic context switching */ - if (readl(sdma->regs + SDMA_H_CONFIG) == 0) - writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG); + reg = readl(sdma->regs + SDMA_H_CONFIG); + if ((reg & SDMA_H_CONFIG_CSM) == 0) { + reg |= SDMA_H_CONFIG_CSM; + writel_relaxed(reg, sdma->regs + SDMA_H_CONFIG); + } return ret; } @@ -1840,6 +1845,9 @@ static int sdma_init(struct sdma_engine *sdma) if (ret) goto disable_clk_ipg; + if (clk_get_rate(sdma->clk_ahb) == clk_get_rate(sdma->clk_ipg)) + sdma->clk_ratio = 1; + /* Be sure SDMA has not started yet */ writel_relaxed(0, sdma->regs + SDMA_H_C0PTR); @@ -1880,8 +1888,10 @@ static int sdma_init(struct sdma_engine *sdma) writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR); /* Set bits of CONFIG register but with static context switching */ - /* FIXME: Check whether to set ACR bit depending on clock ratios */ - writel_relaxed(0, sdma->regs + SDMA_H_CONFIG); + if (sdma->clk_ratio) + writel_relaxed(SDMA_H_CONFIG_ACR, sdma->regs + SDMA_H_CONFIG); + else + writel_relaxed(0, sdma->regs + SDMA_H_CONFIG); writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR);
On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted, since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach to 500Mhz, so use 1:1 instead. Based on NXP commit MLK-16841-1 by Robin Gong <yibin.gong@nxp.com> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> --- drivers/dma/imx-sdma.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-)