| Message ID | 1546409810-37630-2-git-send-email-ley.foon.tan@intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
| Series | Add Stratix 10 PCIe Root Port support | expand |
Apologies, I have dropped the ball on this one. On Wed, Jan 02, 2019 at 02:16:48PM +0800, Ley Foon Tan wrote: > Add PCIe Root Port support for Stratix 10 device. > > Main differences: > - HIP interface to access Root Port configuration register. > - TLP programming flow: > - One REG0 register > - Don't need to check alignment > > Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > --- > drivers/pci/controller/Kconfig | 2 +- > drivers/pci/controller/pcie-altera.c | 246 ++++++++++++++++++++++++++++++---- > 2 files changed, 223 insertions(+), 25 deletions(-) > > diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig > index 6671946..6012f30 100644 > --- a/drivers/pci/controller/Kconfig > +++ b/drivers/pci/controller/Kconfig > @@ -175,7 +175,7 @@ config PCIE_IPROC_MSI > > config PCIE_ALTERA > bool "Altera PCIe controller" > - depends on ARM || NIOS2 || COMPILE_TEST > + depends on ARM || NIOS2 || ARM64 || COMPILE_TEST This is an unrelated change and should be a separate patch. > help > Say Y here if you want to enable PCIe controller support on Altera > FPGA. > diff --git a/drivers/pci/controller/pcie-altera.c b/drivers/pci/controller/pcie-altera.c > index 7d05e51..4c3b61b 100644 > --- a/drivers/pci/controller/pcie-altera.c > +++ b/drivers/pci/controller/pcie-altera.c > @@ -11,6 +11,7 @@ > #include <linux/irqchip/chained_irq.h> > #include <linux/init.h> > #include <linux/of_address.h> > +#include <linux/of_device.h> > #include <linux/of_irq.h> > #include <linux/of_pci.h> > #include <linux/pci.h> > @@ -37,7 +38,12 @@ > #define RP_LTSSM_MASK 0x1f > #define LTSSM_L0 0xf > > -#define PCIE_CAP_OFFSET 0x80 > +#define S10_RP_TX_CNTRL 0x2004 > +#define S10_RP_RXCPL_REG 0x2008 > +#define S10_RP_RXCPL_STATUS 0x200C > +#define S10_RP_CFG_ADDR(pcie, reg) \ > + (((pcie)->hip_base) + (reg) + (1 << 20)) > + > /* TLP configuration type 0 and 1 */ > #define TLP_FMTTYPE_CFGRD0 0x04 /* Configuration Read Type 0 */ > #define TLP_FMTTYPE_CFGWR0 0x44 /* Configuration Write Type 0 */ > @@ -49,18 +55,19 @@ > #define RP_DEVFN 0 > #define TLP_REQ_ID(bus, devfn) (((bus) << 8) | (devfn)) > #define TLP_CFGRD_DW0(pcie, bus) \ > - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGRD0 \ > - : TLP_FMTTYPE_CFGRD1) << 24) | \ > - TLP_PAYLOAD_SIZE) > + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgrd0 \ > + : pcie->pcie_data->cfgrd1) << 24) | \ > + TLP_PAYLOAD_SIZE) > #define TLP_CFGWR_DW0(pcie, bus) \ > - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGWR0 \ > - : TLP_FMTTYPE_CFGWR1) << 24) | \ > - TLP_PAYLOAD_SIZE) > + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgwr0 \ > + : pcie->pcie_data->cfgwr1) << 24) | \ > + TLP_PAYLOAD_SIZE) > #define TLP_CFG_DW1(pcie, tag, be) \ > - (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) > + (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) > #define TLP_CFG_DW2(bus, devfn, offset) \ > (((bus) << 24) | ((devfn) << 16) | (offset)) > #define TLP_COMP_STATUS(s) (((s) >> 13) & 7) > +#define TLP_BYTE_COUNT(s) (((s) >> 0) & 0xfff) > #define TLP_HDR_SIZE 3 > #define TLP_LOOP 500 > > @@ -69,14 +76,43 @@ > > #define DWORD_MASK 3 > > +#define S10_TLP_FMTTYPE_CFGRD0 0x05 > +#define S10_TLP_FMTTYPE_CFGRD1 0x04 > +#define S10_TLP_FMTTYPE_CFGWR0 0x45 > +#define S10_TLP_FMTTYPE_CFGWR1 0x44 > + > +enum altera_pcie_version { > + ALTERA_PCIE_V1 = 0, > + ALTERA_PCIE_V2, > +}; > + > struct altera_pcie { > struct platform_device *pdev; > - void __iomem *cra_base; /* DT Cra */ > + void __iomem *cra_base; > + void __iomem *hip_base; > int irq; > u8 root_bus_nr; > struct irq_domain *irq_domain; > struct resource bus_range; > struct list_head resources; > + const struct altera_pcie_data *pcie_data; > +}; > + > +struct altera_pcie_data { > + int (*tlp_read_pkt)(struct altera_pcie *pcie, u32 *value); > + void (*tlp_write_pkt)(struct altera_pcie *pcie, u32 *headers, > + u32 data, bool align); > + bool (*get_link_status)(struct altera_pcie *pcie); > + int (*rp_read_cfg)(struct altera_pcie *pcie, int where, > + int size, u32 *value); > + int (*rp_write_cfg)(struct altera_pcie *pcie, u8 bus, int where, > + int size, u32 value); > + enum altera_pcie_version version; > + u32 cap_offset; /* PCIe capability structure register offset */ > + u32 cfgrd0; > + u32 cfgrd1; > + u32 cfgwr0; > + u32 cfgwr1; > }; > > struct tlp_rp_regpair_t { > @@ -101,6 +137,15 @@ static bool altera_pcie_link_up(struct altera_pcie *pcie) > return !!((cra_readl(pcie, RP_LTSSM) & RP_LTSSM_MASK) == LTSSM_L0); > } > > +static bool s10_altera_pcie_link_up(struct altera_pcie *pcie) > +{ > + void __iomem *addr = S10_RP_CFG_ADDR(pcie, > + pcie->pcie_data->cap_offset + > + PCI_EXP_LNKSTA); > + > + return !!(readw(addr) & PCI_EXP_LNKSTA_DLLLA); > +} > + > /* > * Altera PCIe port uses BAR0 of RC's configuration space as the translation > * from PCI bus to native BUS. Entire DDR region is mapped into PCIe space > @@ -128,12 +173,18 @@ static void tlp_write_tx(struct altera_pcie *pcie, > cra_writel(pcie, tlp_rp_regdata->ctrl, RP_TX_CNTRL); > } > > +static void s10_tlp_write_tx(struct altera_pcie *pcie, u32 reg0, u32 ctrl) > +{ > + cra_writel(pcie, reg0, RP_TX_REG0); > + cra_writel(pcie, ctrl, S10_RP_TX_CNTRL); > +} > + > static bool altera_pcie_valid_device(struct altera_pcie *pcie, > struct pci_bus *bus, int dev) > { > /* If there is no link, then there is no device */ > if (bus->number != pcie->root_bus_nr) { > - if (!altera_pcie_link_up(pcie)) > + if (!pcie->pcie_data->get_link_status(pcie)) > return false; > } > > @@ -183,6 +234,46 @@ static int tlp_read_packet(struct altera_pcie *pcie, u32 *value) > return PCIBIOS_DEVICE_NOT_FOUND; > } > > +static int s10_tlp_read_packet(struct altera_pcie *pcie, u32 *value) > +{ > + int i; > + u32 ctrl; > + u32 comp_status; > + u32 dw[4]; > + u32 count = 0; > + > + for (i = 0; i < TLP_LOOP; i++) { > + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); > + if (!(ctrl & RP_RXCPL_SOP)) > + continue; > + > + /* Read first DW */ > + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); > + > + /* Poll for EOP */ > + for (i = 0; i < TLP_LOOP; i++) { > + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); > + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); > + if (ctrl & RP_RXCPL_EOP) { > + comp_status = TLP_COMP_STATUS(dw[1]); > + if (comp_status) > + return PCIBIOS_DEVICE_NOT_FOUND; > + > + if (value && > + TLP_BYTE_COUNT(dw[1]) == sizeof(u32) && > + count >= 3) > + *value = dw[3]; Can you explain please the logic behind the loop ? In particular how count is managed. I am also a bit baffled by why you need to get into this inner loop to test the value pointer validity, whose assignment as far as I know is the only side effect of this call (ie if value is NULL, what's the point of executing this function at all ?). > + > + return PCIBIOS_SUCCESSFUL; > + } > + } > + > + udelay(5); > + } > + > + return PCIBIOS_DEVICE_NOT_FOUND; > +} > + > static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > u32 data, bool align) > { > @@ -210,6 +301,15 @@ static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > tlp_write_tx(pcie, &tlp_rp_regdata); > } > > +static void s10_tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > + u32 data, bool dummy) > +{ > + s10_tlp_write_tx(pcie, headers[0], RP_TX_SOP); > + s10_tlp_write_tx(pcie, headers[1], 0); > + s10_tlp_write_tx(pcie, headers[2], 0); > + s10_tlp_write_tx(pcie, data, RP_TX_EOP); > +} > + > static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, > int where, u8 byte_en, u32 *value) > { > @@ -219,9 +319,9 @@ static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, > headers[1] = TLP_CFG_DW1(pcie, TLP_READ_TAG, byte_en); > headers[2] = TLP_CFG_DW2(bus, devfn, where); > > - tlp_write_packet(pcie, headers, 0, false); > + pcie->pcie_data->tlp_write_pkt(pcie, headers, 0, false); > > - return tlp_read_packet(pcie, value); > + return pcie->pcie_data->tlp_read_pkt(pcie, value); > } > > static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > @@ -236,11 +336,11 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > > /* check alignment to Qword */ > if ((where & 0x7) == 0) > - tlp_write_packet(pcie, headers, value, true); > + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, true); > else > - tlp_write_packet(pcie, headers, value, false); > + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, false); > > - ret = tlp_read_packet(pcie, NULL); > + ret = pcie->pcie_data->tlp_read_pkt(pcie, NULL); > if (ret != PCIBIOS_SUCCESSFUL) > return ret; > > @@ -254,6 +354,53 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > return PCIBIOS_SUCCESSFUL; > } > > +static int s10_rp_read_cfg(struct altera_pcie *pcie, int where, > + int size, u32 *value) > +{ > + void *addr = S10_RP_CFG_ADDR(pcie, where); > + > + switch (size) { > + case 1: > + *value = readb(addr); > + break; > + case 2: > + *value = readw(addr); > + break; > + default: > + *value = readl(addr); > + break; > + } > + > + return PCIBIOS_SUCCESSFUL; > +} > + > +static int s10_rp_write_cfg(struct altera_pcie *pcie, u8 bus, int where, > + int size, u32 value) > +{ > + void *addr = S10_RP_CFG_ADDR(pcie, where); > + > + switch (size) { > + case 1: > + writeb(value, addr); > + break; > + case 2: > + writew(value, addr); > + break; > + default: > + writel(value, addr); > + break; > + } > + > + /* > + * Monitor changes to PCI_PRIMARY_BUS register on root port > + * and update local copy of root bus number accordingly. > + */ > + if (bus == pcie->root_bus_nr && where == PCI_PRIMARY_BUS) > + pcie->root_bus_nr = (u8)(value); Mask it, don't cast it. I assume this primary bus tracking thing is to issue the right config type transactions. Lorenzo > + return PCIBIOS_SUCCESSFUL; > +} > + > static int _altera_pcie_cfg_read(struct altera_pcie *pcie, u8 busno, > unsigned int devfn, int where, int size, > u32 *value) > @@ -262,6 +409,9 @@ static int _altera_pcie_cfg_read(struct altera_pcie *pcie, u8 busno, > u32 data; > u8 byte_en; > > + if (busno == pcie->root_bus_nr && pcie->pcie_data->rp_read_cfg) > + return pcie->pcie_data->rp_read_cfg(pcie, where, size, value); > + > switch (size) { > case 1: > byte_en = 1 << (where & 3); > @@ -302,6 +452,10 @@ static int _altera_pcie_cfg_write(struct altera_pcie *pcie, u8 busno, > u32 shift = 8 * (where & 3); > u8 byte_en; > > + if (busno == pcie->root_bus_nr && pcie->pcie_data->rp_write_cfg) > + return pcie->pcie_data->rp_write_cfg(pcie, busno, where, > + size, value); > + > switch (size) { > case 1: > data32 = (value & 0xff) << shift; > @@ -365,7 +519,8 @@ static int altera_read_cap_word(struct altera_pcie *pcie, u8 busno, > int ret; > > ret = _altera_pcie_cfg_read(pcie, busno, devfn, > - PCIE_CAP_OFFSET + offset, sizeof(*value), > + pcie->pcie_data->cap_offset + offset, > + sizeof(*value), > &data); > *value = data; > return ret; > @@ -375,7 +530,8 @@ static int altera_write_cap_word(struct altera_pcie *pcie, u8 busno, > unsigned int devfn, int offset, u16 value) > { > return _altera_pcie_cfg_write(pcie, busno, devfn, > - PCIE_CAP_OFFSET + offset, sizeof(value), > + pcie->pcie_data->cap_offset + offset, > + sizeof(value), > value); > } > > @@ -403,7 +559,7 @@ static void altera_wait_link_retrain(struct altera_pcie *pcie) > /* Wait for link is up */ > start_jiffies = jiffies; > for (;;) { > - if (altera_pcie_link_up(pcie)) > + if (pcie->pcie_data->get_link_status(pcie)) > break; > > if (time_after(jiffies, start_jiffies + LINK_UP_TIMEOUT)) { > @@ -418,7 +574,7 @@ static void altera_pcie_retrain(struct altera_pcie *pcie) > { > u16 linkcap, linkstat, linkctl; > > - if (!altera_pcie_link_up(pcie)) > + if (!pcie->pcie_data->get_link_status(pcie)) > return; > > /* > @@ -540,12 +696,20 @@ static int altera_pcie_parse_dt(struct altera_pcie *pcie) > struct device *dev = &pcie->pdev->dev; > struct platform_device *pdev = pcie->pdev; > struct resource *cra; > + struct resource *hip; > > cra = platform_get_resource_byname(pdev, IORESOURCE_MEM, "Cra"); > pcie->cra_base = devm_ioremap_resource(dev, cra); > if (IS_ERR(pcie->cra_base)) > return PTR_ERR(pcie->cra_base); > > + if (pcie->pcie_data->version == ALTERA_PCIE_V2) { > + hip = platform_get_resource_byname(pdev, IORESOURCE_MEM, "Hip"); > + pcie->hip_base = devm_ioremap_resource(&pdev->dev, hip); > + if (IS_ERR(pcie->hip_base)) > + return PTR_ERR(pcie->hip_base); > + } > + > /* setup IRQ */ > pcie->irq = platform_get_irq(pdev, 0); > if (pcie->irq < 0) { > @@ -562,6 +726,38 @@ static void altera_pcie_host_init(struct altera_pcie *pcie) > altera_pcie_retrain(pcie); > } > > +static struct altera_pcie_data pci_1_0_data = { > + .tlp_read_pkt = tlp_read_packet, > + .tlp_write_pkt = tlp_write_packet, > + .get_link_status = altera_pcie_link_up, > + .cap_offset = 0x80, > + .version = ALTERA_PCIE_V1, > + .cfgrd0 = TLP_FMTTYPE_CFGRD0, > + .cfgrd1 = TLP_FMTTYPE_CFGRD1, > + .cfgwr0 = TLP_FMTTYPE_CFGWR0, > + .cfgwr1 = TLP_FMTTYPE_CFGWR1, > +}; > + > +static struct altera_pcie_data pci_2_0_data = { > + .tlp_read_pkt = s10_tlp_read_packet, > + .tlp_write_pkt = s10_tlp_write_packet, > + .get_link_status = s10_altera_pcie_link_up, > + .rp_read_cfg = s10_rp_read_cfg, > + .rp_write_cfg = s10_rp_write_cfg, > + .version = ALTERA_PCIE_V2, > + .cap_offset = 0x70, > + .cfgrd0 = S10_TLP_FMTTYPE_CFGRD0, > + .cfgrd1 = S10_TLP_FMTTYPE_CFGRD1, > + .cfgwr0 = S10_TLP_FMTTYPE_CFGWR0, > + .cfgwr1 = S10_TLP_FMTTYPE_CFGWR1, > +}; > + > +static const struct of_device_id altera_pcie_of_match[] = { > + { .compatible = "altr,pcie-root-port-1.0", .data = &pci_1_0_data }, > + { .compatible = "altr,pcie-root-port-2.0", .data = &pci_2_0_data }, > + {}, > +}; > + > static int altera_pcie_probe(struct platform_device *pdev) > { > struct device *dev = &pdev->dev; > @@ -570,6 +766,7 @@ static int altera_pcie_probe(struct platform_device *pdev) > struct pci_bus *child; > struct pci_host_bridge *bridge; > int ret; > + const struct of_device_id *match; > > bridge = devm_pci_alloc_host_bridge(dev, sizeof(*pcie)); > if (!bridge) > @@ -578,6 +775,12 @@ static int altera_pcie_probe(struct platform_device *pdev) > pcie = pci_host_bridge_priv(bridge); > pcie->pdev = pdev; > > + match = of_match_device(altera_pcie_of_match, &pdev->dev); > + if (!match) > + return -ENODEV; > + > + pcie->pcie_data = match->data; > + > ret = altera_pcie_parse_dt(pcie); > if (ret) { > dev_err(dev, "Parsing DT failed\n"); > @@ -628,11 +831,6 @@ static int altera_pcie_probe(struct platform_device *pdev) > return ret; > } > > -static const struct of_device_id altera_pcie_of_match[] = { > - { .compatible = "altr,pcie-root-port-1.0", }, > - {}, > -}; > - > static struct platform_driver altera_pcie_driver = { > .probe = altera_pcie_probe, > .driver = { > -- > 1.7.1 >
On Sat, Feb 9, 2019 at 12:29 AM Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> wrote: > > Apologies, I have dropped the ball on this one. > > On Wed, Jan 02, 2019 at 02:16:48PM +0800, Ley Foon Tan wrote: > > Add PCIe Root Port support for Stratix 10 device. > > > > Main differences: > > - HIP interface to access Root Port configuration register. > > - TLP programming flow: > > - One REG0 register > > - Don't need to check alignment > > > > Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > > --- > > drivers/pci/controller/Kconfig | 2 +- > > drivers/pci/controller/pcie-altera.c | 246 ++++++++++++++++++++++++++++++---- > > 2 files changed, 223 insertions(+), 25 deletions(-) > > > > diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig > > index 6671946..6012f30 100644 > > --- a/drivers/pci/controller/Kconfig > > +++ b/drivers/pci/controller/Kconfig > > @@ -175,7 +175,7 @@ config PCIE_IPROC_MSI > > > > config PCIE_ALTERA > > bool "Altera PCIe controller" > > - depends on ARM || NIOS2 || COMPILE_TEST > > + depends on ARM || NIOS2 || ARM64 || COMPILE_TEST > > This is an unrelated change and should be a separate patch. Noted. > > > help > > Say Y here if you want to enable PCIe controller support on Altera > > FPGA. > > diff --git a/drivers/pci/controller/pcie-altera.c b/drivers/pci/controller/pcie-altera.c > > index 7d05e51..4c3b61b 100644 > > --- a/drivers/pci/controller/pcie-altera.c > > +++ b/drivers/pci/controller/pcie-altera.c > > @@ -11,6 +11,7 @@ > > #include <linux/irqchip/chained_irq.h> > > #include <linux/init.h> > > #include <linux/of_address.h> > > +#include <linux/of_device.h> > > #include <linux/of_irq.h> > > #include <linux/of_pci.h> > > #include <linux/pci.h> > > @@ -37,7 +38,12 @@ > > #define RP_LTSSM_MASK 0x1f > > #define LTSSM_L0 0xf > > > > -#define PCIE_CAP_OFFSET 0x80 > > +#define S10_RP_TX_CNTRL 0x2004 > > +#define S10_RP_RXCPL_REG 0x2008 > > +#define S10_RP_RXCPL_STATUS 0x200C > > +#define S10_RP_CFG_ADDR(pcie, reg) \ > > + (((pcie)->hip_base) + (reg) + (1 << 20)) > > + > > /* TLP configuration type 0 and 1 */ > > #define TLP_FMTTYPE_CFGRD0 0x04 /* Configuration Read Type 0 */ > > #define TLP_FMTTYPE_CFGWR0 0x44 /* Configuration Write Type 0 */ > > @@ -49,18 +55,19 @@ > > #define RP_DEVFN 0 > > #define TLP_REQ_ID(bus, devfn) (((bus) << 8) | (devfn)) > > #define TLP_CFGRD_DW0(pcie, bus) \ > > - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGRD0 \ > > - : TLP_FMTTYPE_CFGRD1) << 24) | \ > > - TLP_PAYLOAD_SIZE) > > + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgrd0 \ > > + : pcie->pcie_data->cfgrd1) << 24) | \ > > + TLP_PAYLOAD_SIZE) > > #define TLP_CFGWR_DW0(pcie, bus) \ > > - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGWR0 \ > > - : TLP_FMTTYPE_CFGWR1) << 24) | \ > > - TLP_PAYLOAD_SIZE) > > + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgwr0 \ > > + : pcie->pcie_data->cfgwr1) << 24) | \ > > + TLP_PAYLOAD_SIZE) > > #define TLP_CFG_DW1(pcie, tag, be) \ > > - (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) > > + (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) > > #define TLP_CFG_DW2(bus, devfn, offset) \ > > (((bus) << 24) | ((devfn) << 16) | (offset)) > > #define TLP_COMP_STATUS(s) (((s) >> 13) & 7) > > +#define TLP_BYTE_COUNT(s) (((s) >> 0) & 0xfff) > > #define TLP_HDR_SIZE 3 > > #define TLP_LOOP 500 > > > > @@ -69,14 +76,43 @@ > > > > #define DWORD_MASK 3 > > > > +#define S10_TLP_FMTTYPE_CFGRD0 0x05 > > +#define S10_TLP_FMTTYPE_CFGRD1 0x04 > > +#define S10_TLP_FMTTYPE_CFGWR0 0x45 > > +#define S10_TLP_FMTTYPE_CFGWR1 0x44 > > + > > +enum altera_pcie_version { > > + ALTERA_PCIE_V1 = 0, > > + ALTERA_PCIE_V2, > > +}; > > + > > struct altera_pcie { > > struct platform_device *pdev; > > - void __iomem *cra_base; /* DT Cra */ > > + void __iomem *cra_base; > > + void __iomem *hip_base; > > int irq; > > u8 root_bus_nr; > > struct irq_domain *irq_domain; > > struct resource bus_range; > > struct list_head resources; > > + const struct altera_pcie_data *pcie_data; > > +}; > > + > > +struct altera_pcie_data { > > + int (*tlp_read_pkt)(struct altera_pcie *pcie, u32 *value); > > + void (*tlp_write_pkt)(struct altera_pcie *pcie, u32 *headers, > > + u32 data, bool align); > > + bool (*get_link_status)(struct altera_pcie *pcie); > > + int (*rp_read_cfg)(struct altera_pcie *pcie, int where, > > + int size, u32 *value); > > + int (*rp_write_cfg)(struct altera_pcie *pcie, u8 bus, int where, > > + int size, u32 value); > > + enum altera_pcie_version version; > > + u32 cap_offset; /* PCIe capability structure register offset */ > > + u32 cfgrd0; > > + u32 cfgrd1; > > + u32 cfgwr0; > > + u32 cfgwr1; > > }; > > > > struct tlp_rp_regpair_t { > > @@ -101,6 +137,15 @@ static bool altera_pcie_link_up(struct altera_pcie *pcie) > > return !!((cra_readl(pcie, RP_LTSSM) & RP_LTSSM_MASK) == LTSSM_L0); > > } > > > > +static bool s10_altera_pcie_link_up(struct altera_pcie *pcie) > > +{ > > + void __iomem *addr = S10_RP_CFG_ADDR(pcie, > > + pcie->pcie_data->cap_offset + > > + PCI_EXP_LNKSTA); > > + > > + return !!(readw(addr) & PCI_EXP_LNKSTA_DLLLA); > > +} > > + > > /* > > * Altera PCIe port uses BAR0 of RC's configuration space as the translation > > * from PCI bus to native BUS. Entire DDR region is mapped into PCIe space > > @@ -128,12 +173,18 @@ static void tlp_write_tx(struct altera_pcie *pcie, > > cra_writel(pcie, tlp_rp_regdata->ctrl, RP_TX_CNTRL); > > } > > > > +static void s10_tlp_write_tx(struct altera_pcie *pcie, u32 reg0, u32 ctrl) > > +{ > > + cra_writel(pcie, reg0, RP_TX_REG0); > > + cra_writel(pcie, ctrl, S10_RP_TX_CNTRL); > > +} > > + > > static bool altera_pcie_valid_device(struct altera_pcie *pcie, > > struct pci_bus *bus, int dev) > > { > > /* If there is no link, then there is no device */ > > if (bus->number != pcie->root_bus_nr) { > > - if (!altera_pcie_link_up(pcie)) > > + if (!pcie->pcie_data->get_link_status(pcie)) > > return false; > > } > > > > @@ -183,6 +234,46 @@ static int tlp_read_packet(struct altera_pcie *pcie, u32 *value) > > return PCIBIOS_DEVICE_NOT_FOUND; > > } > > > > +static int s10_tlp_read_packet(struct altera_pcie *pcie, u32 *value) > > +{ > > + int i; > > + u32 ctrl; > > + u32 comp_status; > > + u32 dw[4]; > > + u32 count = 0; > > + > > + for (i = 0; i < TLP_LOOP; i++) { > > + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); > > + if (!(ctrl & RP_RXCPL_SOP)) > > + continue; > > + > > + /* Read first DW */ > > + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); > > + > > + /* Poll for EOP */ > > + for (i = 0; i < TLP_LOOP; i++) { > > + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); > > + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); > > + if (ctrl & RP_RXCPL_EOP) { > > + comp_status = TLP_COMP_STATUS(dw[1]); > > + if (comp_status) > > + return PCIBIOS_DEVICE_NOT_FOUND; > > + > > + if (value && > > + TLP_BYTE_COUNT(dw[1]) == sizeof(u32) && > > + count >= 3) > > + *value = dw[3]; > > Can you explain please the logic behind the loop ? In particular how > count is managed. Firstly, the loop is polling for SOP (start of packet) bit and it will start poll for EOP (end of packet) if SOP is received. The count is number of 32-bit data read from PCIe controller (TLP data). > > I am also a bit baffled by why you need to get into this inner loop > to test the value pointer validity, whose assignment as far as I know is > the only side effect of this call (ie if value is NULL, what's the point > of executing this function at all ?). There are 2 cases of read TLP packets transaction: (1) Without response data - TLP completion header only, check TLP completion status for success/fail. In this case, "value" is NULL. (2) With response data - TLP completion header + data. Check TLP completion status for success/fail. If status is success and have response data, then store the data to "value". Usually, this is for config read. > > > + > > + return PCIBIOS_SUCCESSFUL; > > + } > > + } > > + > > + udelay(5); > > + } > > + > > + return PCIBIOS_DEVICE_NOT_FOUND; > > +} > > + > > static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > > u32 data, bool align) > > { > > @@ -210,6 +301,15 @@ static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > > tlp_write_tx(pcie, &tlp_rp_regdata); > > } > > > > +static void s10_tlp_write_packet(struct altera_pcie *pcie, u32 *headers, > > + u32 data, bool dummy) > > +{ > > + s10_tlp_write_tx(pcie, headers[0], RP_TX_SOP); > > + s10_tlp_write_tx(pcie, headers[1], 0); > > + s10_tlp_write_tx(pcie, headers[2], 0); > > + s10_tlp_write_tx(pcie, data, RP_TX_EOP); > > +} > > + > > static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, > > int where, u8 byte_en, u32 *value) > > { > > @@ -219,9 +319,9 @@ static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, > > headers[1] = TLP_CFG_DW1(pcie, TLP_READ_TAG, byte_en); > > headers[2] = TLP_CFG_DW2(bus, devfn, where); > > > > - tlp_write_packet(pcie, headers, 0, false); > > + pcie->pcie_data->tlp_write_pkt(pcie, headers, 0, false); > > > > - return tlp_read_packet(pcie, value); > > + return pcie->pcie_data->tlp_read_pkt(pcie, value); > > } > > > > static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > > @@ -236,11 +336,11 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > > > > /* check alignment to Qword */ > > if ((where & 0x7) == 0) > > - tlp_write_packet(pcie, headers, value, true); > > + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, true); > > else > > - tlp_write_packet(pcie, headers, value, false); > > + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, false); > > > > - ret = tlp_read_packet(pcie, NULL); > > + ret = pcie->pcie_data->tlp_read_pkt(pcie, NULL); > > if (ret != PCIBIOS_SUCCESSFUL) > > return ret; > > > > @@ -254,6 +354,53 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, > > return PCIBIOS_SUCCESSFUL; > > } > > > > +static int s10_rp_read_cfg(struct altera_pcie *pcie, int where, > > + int size, u32 *value) > > +{ > > + void *addr = S10_RP_CFG_ADDR(pcie, where); > > + > > + switch (size) { > > + case 1: > > + *value = readb(addr); > > + break; > > + case 2: > > + *value = readw(addr); > > + break; > > + default: > > + *value = readl(addr); > > + break; > > + } > > + > > + return PCIBIOS_SUCCESSFUL; > > +} > > + > > +static int s10_rp_write_cfg(struct altera_pcie *pcie, u8 bus, int where, > > + int size, u32 value) > > +{ > > + void *addr = S10_RP_CFG_ADDR(pcie, where); > > + > > + switch (size) { > > + case 1: > > + writeb(value, addr); > > + break; > > + case 2: > > + writew(value, addr); > > + break; > > + default: > > + writel(value, addr); > > + break; > > + } > > + > > + /* > > + * Monitor changes to PCI_PRIMARY_BUS register on root port > > + * and update local copy of root bus number accordingly. > > + */ > > + if (bus == pcie->root_bus_nr && where == PCI_PRIMARY_BUS) > > + pcie->root_bus_nr = (u8)(value); > > Mask it, don't cast it. I assume this primary bus tracking thing > is to issue the right config type transactions. Yes, will change to mask. Regards Ley Foon
diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig index 6671946..6012f30 100644 --- a/drivers/pci/controller/Kconfig +++ b/drivers/pci/controller/Kconfig @@ -175,7 +175,7 @@ config PCIE_IPROC_MSI config PCIE_ALTERA bool "Altera PCIe controller" - depends on ARM || NIOS2 || COMPILE_TEST + depends on ARM || NIOS2 || ARM64 || COMPILE_TEST help Say Y here if you want to enable PCIe controller support on Altera FPGA. diff --git a/drivers/pci/controller/pcie-altera.c b/drivers/pci/controller/pcie-altera.c index 7d05e51..4c3b61b 100644 --- a/drivers/pci/controller/pcie-altera.c +++ b/drivers/pci/controller/pcie-altera.c @@ -11,6 +11,7 @@ #include <linux/irqchip/chained_irq.h> #include <linux/init.h> #include <linux/of_address.h> +#include <linux/of_device.h> #include <linux/of_irq.h> #include <linux/of_pci.h> #include <linux/pci.h> @@ -37,7 +38,12 @@ #define RP_LTSSM_MASK 0x1f #define LTSSM_L0 0xf -#define PCIE_CAP_OFFSET 0x80 +#define S10_RP_TX_CNTRL 0x2004 +#define S10_RP_RXCPL_REG 0x2008 +#define S10_RP_RXCPL_STATUS 0x200C +#define S10_RP_CFG_ADDR(pcie, reg) \ + (((pcie)->hip_base) + (reg) + (1 << 20)) + /* TLP configuration type 0 and 1 */ #define TLP_FMTTYPE_CFGRD0 0x04 /* Configuration Read Type 0 */ #define TLP_FMTTYPE_CFGWR0 0x44 /* Configuration Write Type 0 */ @@ -49,18 +55,19 @@ #define RP_DEVFN 0 #define TLP_REQ_ID(bus, devfn) (((bus) << 8) | (devfn)) #define TLP_CFGRD_DW0(pcie, bus) \ - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGRD0 \ - : TLP_FMTTYPE_CFGRD1) << 24) | \ - TLP_PAYLOAD_SIZE) + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgrd0 \ + : pcie->pcie_data->cfgrd1) << 24) | \ + TLP_PAYLOAD_SIZE) #define TLP_CFGWR_DW0(pcie, bus) \ - ((((bus == pcie->root_bus_nr) ? TLP_FMTTYPE_CFGWR0 \ - : TLP_FMTTYPE_CFGWR1) << 24) | \ - TLP_PAYLOAD_SIZE) + ((((bus == pcie->root_bus_nr) ? pcie->pcie_data->cfgwr0 \ + : pcie->pcie_data->cfgwr1) << 24) | \ + TLP_PAYLOAD_SIZE) #define TLP_CFG_DW1(pcie, tag, be) \ - (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) + (((TLP_REQ_ID(pcie->root_bus_nr, RP_DEVFN)) << 16) | (tag << 8) | (be)) #define TLP_CFG_DW2(bus, devfn, offset) \ (((bus) << 24) | ((devfn) << 16) | (offset)) #define TLP_COMP_STATUS(s) (((s) >> 13) & 7) +#define TLP_BYTE_COUNT(s) (((s) >> 0) & 0xfff) #define TLP_HDR_SIZE 3 #define TLP_LOOP 500 @@ -69,14 +76,43 @@ #define DWORD_MASK 3 +#define S10_TLP_FMTTYPE_CFGRD0 0x05 +#define S10_TLP_FMTTYPE_CFGRD1 0x04 +#define S10_TLP_FMTTYPE_CFGWR0 0x45 +#define S10_TLP_FMTTYPE_CFGWR1 0x44 + +enum altera_pcie_version { + ALTERA_PCIE_V1 = 0, + ALTERA_PCIE_V2, +}; + struct altera_pcie { struct platform_device *pdev; - void __iomem *cra_base; /* DT Cra */ + void __iomem *cra_base; + void __iomem *hip_base; int irq; u8 root_bus_nr; struct irq_domain *irq_domain; struct resource bus_range; struct list_head resources; + const struct altera_pcie_data *pcie_data; +}; + +struct altera_pcie_data { + int (*tlp_read_pkt)(struct altera_pcie *pcie, u32 *value); + void (*tlp_write_pkt)(struct altera_pcie *pcie, u32 *headers, + u32 data, bool align); + bool (*get_link_status)(struct altera_pcie *pcie); + int (*rp_read_cfg)(struct altera_pcie *pcie, int where, + int size, u32 *value); + int (*rp_write_cfg)(struct altera_pcie *pcie, u8 bus, int where, + int size, u32 value); + enum altera_pcie_version version; + u32 cap_offset; /* PCIe capability structure register offset */ + u32 cfgrd0; + u32 cfgrd1; + u32 cfgwr0; + u32 cfgwr1; }; struct tlp_rp_regpair_t { @@ -101,6 +137,15 @@ static bool altera_pcie_link_up(struct altera_pcie *pcie) return !!((cra_readl(pcie, RP_LTSSM) & RP_LTSSM_MASK) == LTSSM_L0); } +static bool s10_altera_pcie_link_up(struct altera_pcie *pcie) +{ + void __iomem *addr = S10_RP_CFG_ADDR(pcie, + pcie->pcie_data->cap_offset + + PCI_EXP_LNKSTA); + + return !!(readw(addr) & PCI_EXP_LNKSTA_DLLLA); +} + /* * Altera PCIe port uses BAR0 of RC's configuration space as the translation * from PCI bus to native BUS. Entire DDR region is mapped into PCIe space @@ -128,12 +173,18 @@ static void tlp_write_tx(struct altera_pcie *pcie, cra_writel(pcie, tlp_rp_regdata->ctrl, RP_TX_CNTRL); } +static void s10_tlp_write_tx(struct altera_pcie *pcie, u32 reg0, u32 ctrl) +{ + cra_writel(pcie, reg0, RP_TX_REG0); + cra_writel(pcie, ctrl, S10_RP_TX_CNTRL); +} + static bool altera_pcie_valid_device(struct altera_pcie *pcie, struct pci_bus *bus, int dev) { /* If there is no link, then there is no device */ if (bus->number != pcie->root_bus_nr) { - if (!altera_pcie_link_up(pcie)) + if (!pcie->pcie_data->get_link_status(pcie)) return false; } @@ -183,6 +234,46 @@ static int tlp_read_packet(struct altera_pcie *pcie, u32 *value) return PCIBIOS_DEVICE_NOT_FOUND; } +static int s10_tlp_read_packet(struct altera_pcie *pcie, u32 *value) +{ + int i; + u32 ctrl; + u32 comp_status; + u32 dw[4]; + u32 count = 0; + + for (i = 0; i < TLP_LOOP; i++) { + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); + if (!(ctrl & RP_RXCPL_SOP)) + continue; + + /* Read first DW */ + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); + + /* Poll for EOP */ + for (i = 0; i < TLP_LOOP; i++) { + ctrl = cra_readl(pcie, S10_RP_RXCPL_STATUS); + dw[count++] = cra_readl(pcie, S10_RP_RXCPL_REG); + if (ctrl & RP_RXCPL_EOP) { + comp_status = TLP_COMP_STATUS(dw[1]); + if (comp_status) + return PCIBIOS_DEVICE_NOT_FOUND; + + if (value && + TLP_BYTE_COUNT(dw[1]) == sizeof(u32) && + count >= 3) + *value = dw[3]; + + return PCIBIOS_SUCCESSFUL; + } + } + + udelay(5); + } + + return PCIBIOS_DEVICE_NOT_FOUND; +} + static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, u32 data, bool align) { @@ -210,6 +301,15 @@ static void tlp_write_packet(struct altera_pcie *pcie, u32 *headers, tlp_write_tx(pcie, &tlp_rp_regdata); } +static void s10_tlp_write_packet(struct altera_pcie *pcie, u32 *headers, + u32 data, bool dummy) +{ + s10_tlp_write_tx(pcie, headers[0], RP_TX_SOP); + s10_tlp_write_tx(pcie, headers[1], 0); + s10_tlp_write_tx(pcie, headers[2], 0); + s10_tlp_write_tx(pcie, data, RP_TX_EOP); +} + static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, int where, u8 byte_en, u32 *value) { @@ -219,9 +319,9 @@ static int tlp_cfg_dword_read(struct altera_pcie *pcie, u8 bus, u32 devfn, headers[1] = TLP_CFG_DW1(pcie, TLP_READ_TAG, byte_en); headers[2] = TLP_CFG_DW2(bus, devfn, where); - tlp_write_packet(pcie, headers, 0, false); + pcie->pcie_data->tlp_write_pkt(pcie, headers, 0, false); - return tlp_read_packet(pcie, value); + return pcie->pcie_data->tlp_read_pkt(pcie, value); } static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, @@ -236,11 +336,11 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, /* check alignment to Qword */ if ((where & 0x7) == 0) - tlp_write_packet(pcie, headers, value, true); + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, true); else - tlp_write_packet(pcie, headers, value, false); + pcie->pcie_data->tlp_write_pkt(pcie, headers, value, false); - ret = tlp_read_packet(pcie, NULL); + ret = pcie->pcie_data->tlp_read_pkt(pcie, NULL); if (ret != PCIBIOS_SUCCESSFUL) return ret; @@ -254,6 +354,53 @@ static int tlp_cfg_dword_write(struct altera_pcie *pcie, u8 bus, u32 devfn, return PCIBIOS_SUCCESSFUL; } +static int s10_rp_read_cfg(struct altera_pcie *pcie, int where, + int size, u32 *value) +{ + void *addr = S10_RP_CFG_ADDR(pcie, where); + + switch (size) { + case 1: + *value = readb(addr); + break; + case 2: + *value = readw(addr); + break; + default: + *value = readl(addr); + break; + } + + return PCIBIOS_SUCCESSFUL; +} + +static int s10_rp_write_cfg(struct altera_pcie *pcie, u8 bus, int where, + int size, u32 value) +{ + void *addr = S10_RP_CFG_ADDR(pcie, where); + + switch (size) { + case 1: + writeb(value, addr); + break; + case 2: + writew(value, addr); + break; + default: + writel(value, addr); + break; + } + + /* + * Monitor changes to PCI_PRIMARY_BUS register on root port + * and update local copy of root bus number accordingly. + */ + if (bus == pcie->root_bus_nr && where == PCI_PRIMARY_BUS) + pcie->root_bus_nr = (u8)(value); + + return PCIBIOS_SUCCESSFUL; +} + static int _altera_pcie_cfg_read(struct altera_pcie *pcie, u8 busno, unsigned int devfn, int where, int size, u32 *value) @@ -262,6 +409,9 @@ static int _altera_pcie_cfg_read(struct altera_pcie *pcie, u8 busno, u32 data; u8 byte_en; + if (busno == pcie->root_bus_nr && pcie->pcie_data->rp_read_cfg) + return pcie->pcie_data->rp_read_cfg(pcie, where, size, value); + switch (size) { case 1: byte_en = 1 << (where & 3); @@ -302,6 +452,10 @@ static int _altera_pcie_cfg_write(struct altera_pcie *pcie, u8 busno, u32 shift = 8 * (where & 3); u8 byte_en; + if (busno == pcie->root_bus_nr && pcie->pcie_data->rp_write_cfg) + return pcie->pcie_data->rp_write_cfg(pcie, busno, where, + size, value); + switch (size) { case 1: data32 = (value & 0xff) << shift; @@ -365,7 +519,8 @@ static int altera_read_cap_word(struct altera_pcie *pcie, u8 busno, int ret; ret = _altera_pcie_cfg_read(pcie, busno, devfn, - PCIE_CAP_OFFSET + offset, sizeof(*value), + pcie->pcie_data->cap_offset + offset, + sizeof(*value), &data); *value = data; return ret; @@ -375,7 +530,8 @@ static int altera_write_cap_word(struct altera_pcie *pcie, u8 busno, unsigned int devfn, int offset, u16 value) { return _altera_pcie_cfg_write(pcie, busno, devfn, - PCIE_CAP_OFFSET + offset, sizeof(value), + pcie->pcie_data->cap_offset + offset, + sizeof(value), value); } @@ -403,7 +559,7 @@ static void altera_wait_link_retrain(struct altera_pcie *pcie) /* Wait for link is up */ start_jiffies = jiffies; for (;;) { - if (altera_pcie_link_up(pcie)) + if (pcie->pcie_data->get_link_status(pcie)) break; if (time_after(jiffies, start_jiffies + LINK_UP_TIMEOUT)) { @@ -418,7 +574,7 @@ static void altera_pcie_retrain(struct altera_pcie *pcie) { u16 linkcap, linkstat, linkctl; - if (!altera_pcie_link_up(pcie)) + if (!pcie->pcie_data->get_link_status(pcie)) return; /* @@ -540,12 +696,20 @@ static int altera_pcie_parse_dt(struct altera_pcie *pcie) struct device *dev = &pcie->pdev->dev; struct platform_device *pdev = pcie->pdev; struct resource *cra; + struct resource *hip; cra = platform_get_resource_byname(pdev, IORESOURCE_MEM, "Cra"); pcie->cra_base = devm_ioremap_resource(dev, cra); if (IS_ERR(pcie->cra_base)) return PTR_ERR(pcie->cra_base); + if (pcie->pcie_data->version == ALTERA_PCIE_V2) { + hip = platform_get_resource_byname(pdev, IORESOURCE_MEM, "Hip"); + pcie->hip_base = devm_ioremap_resource(&pdev->dev, hip); + if (IS_ERR(pcie->hip_base)) + return PTR_ERR(pcie->hip_base); + } + /* setup IRQ */ pcie->irq = platform_get_irq(pdev, 0); if (pcie->irq < 0) { @@ -562,6 +726,38 @@ static void altera_pcie_host_init(struct altera_pcie *pcie) altera_pcie_retrain(pcie); } +static struct altera_pcie_data pci_1_0_data = { + .tlp_read_pkt = tlp_read_packet, + .tlp_write_pkt = tlp_write_packet, + .get_link_status = altera_pcie_link_up, + .cap_offset = 0x80, + .version = ALTERA_PCIE_V1, + .cfgrd0 = TLP_FMTTYPE_CFGRD0, + .cfgrd1 = TLP_FMTTYPE_CFGRD1, + .cfgwr0 = TLP_FMTTYPE_CFGWR0, + .cfgwr1 = TLP_FMTTYPE_CFGWR1, +}; + +static struct altera_pcie_data pci_2_0_data = { + .tlp_read_pkt = s10_tlp_read_packet, + .tlp_write_pkt = s10_tlp_write_packet, + .get_link_status = s10_altera_pcie_link_up, + .rp_read_cfg = s10_rp_read_cfg, + .rp_write_cfg = s10_rp_write_cfg, + .version = ALTERA_PCIE_V2, + .cap_offset = 0x70, + .cfgrd0 = S10_TLP_FMTTYPE_CFGRD0, + .cfgrd1 = S10_TLP_FMTTYPE_CFGRD1, + .cfgwr0 = S10_TLP_FMTTYPE_CFGWR0, + .cfgwr1 = S10_TLP_FMTTYPE_CFGWR1, +}; + +static const struct of_device_id altera_pcie_of_match[] = { + { .compatible = "altr,pcie-root-port-1.0", .data = &pci_1_0_data }, + { .compatible = "altr,pcie-root-port-2.0", .data = &pci_2_0_data }, + {}, +}; + static int altera_pcie_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -570,6 +766,7 @@ static int altera_pcie_probe(struct platform_device *pdev) struct pci_bus *child; struct pci_host_bridge *bridge; int ret; + const struct of_device_id *match; bridge = devm_pci_alloc_host_bridge(dev, sizeof(*pcie)); if (!bridge) @@ -578,6 +775,12 @@ static int altera_pcie_probe(struct platform_device *pdev) pcie = pci_host_bridge_priv(bridge); pcie->pdev = pdev; + match = of_match_device(altera_pcie_of_match, &pdev->dev); + if (!match) + return -ENODEV; + + pcie->pcie_data = match->data; + ret = altera_pcie_parse_dt(pcie); if (ret) { dev_err(dev, "Parsing DT failed\n"); @@ -628,11 +831,6 @@ static int altera_pcie_probe(struct platform_device *pdev) return ret; } -static const struct of_device_id altera_pcie_of_match[] = { - { .compatible = "altr,pcie-root-port-1.0", }, - {}, -}; - static struct platform_driver altera_pcie_driver = { .probe = altera_pcie_probe, .driver = {
Add PCIe Root Port support for Stratix 10 device. Main differences: - HIP interface to access Root Port configuration register. - TLP programming flow: - One REG0 register - Don't need to check alignment Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> --- drivers/pci/controller/Kconfig | 2 +- drivers/pci/controller/pcie-altera.c | 246 ++++++++++++++++++++++++++++++---- 2 files changed, 223 insertions(+), 25 deletions(-)