@@ -191,83 +191,6 @@ config DMA_FENCE_TRACE
lockup related problems for dma-buffers shared across multiple
devices.
-config DMA_CMA
- bool "DMA Contiguous Memory Allocator"
- depends on HAVE_DMA_CONTIGUOUS && CMA
- help
- This enables the Contiguous Memory Allocator which allows drivers
- to allocate big physically-contiguous blocks of memory for use with
- hardware components that do not support I/O map nor scatter-gather.
-
- You can disable CMA by specifying "cma=0" on the kernel's command
- line.
-
- For more information see <include/linux/dma-contiguous.h>.
- If unsure, say "n".
-
-if DMA_CMA
-comment "Default contiguous memory area size:"
-
-config CMA_SIZE_MBYTES
- int "Size in Mega Bytes"
- depends on !CMA_SIZE_SEL_PERCENTAGE
- default 0 if X86
- default 16
- help
- Defines the size (in MiB) of the default memory area for Contiguous
- Memory Allocator. If the size of 0 is selected, CMA is disabled by
- default, but it can be enabled by passing cma=size[MG] to the kernel.
-
-
-config CMA_SIZE_PERCENTAGE
- int "Percentage of total memory"
- depends on !CMA_SIZE_SEL_MBYTES
- default 0 if X86
- default 10
- help
- Defines the size of the default memory area for Contiguous Memory
- Allocator as a percentage of the total memory in the system.
- If 0 percent is selected, CMA is disabled by default, but it can be
- enabled by passing cma=size[MG] to the kernel.
-
-choice
- prompt "Selected region size"
- default CMA_SIZE_SEL_MBYTES
-
-config CMA_SIZE_SEL_MBYTES
- bool "Use mega bytes value only"
-
-config CMA_SIZE_SEL_PERCENTAGE
- bool "Use percentage value only"
-
-config CMA_SIZE_SEL_MIN
- bool "Use lower value (minimum)"
-
-config CMA_SIZE_SEL_MAX
- bool "Use higher value (maximum)"
-
-endchoice
-
-config CMA_ALIGNMENT
- int "Maximum PAGE_SIZE order of alignment for contiguous buffers"
- range 4 12
- default 8
- help
- DMA mapping framework by default aligns all buffers to the smallest
- PAGE_SIZE order which is greater than or equal to the requested buffer
- size. This works well for buffers up to a few hundreds kilobytes, but
- for larger buffers it just a memory waste. With this parameter you can
- specify the maximum PAGE_SIZE order for contiguous buffers. Larger
- buffers will be aligned only to this specified order. The order is
- expressed as a power of two multiplied by the PAGE_SIZE.
-
- For example, if your system defaults to 4KiB pages, the order value
- of 8 means that the buffers will be aligned up to 1MiB only.
-
- If unsure, leave the default value "8".
-
-endif
-
config GENERIC_ARCH_TOPOLOGY
bool
help
@@ -53,3 +53,80 @@ config DMA_REMAP
config DMA_DIRECT_REMAP
bool
select DMA_REMAP
+
+config DMA_CMA
+ bool "DMA Contiguous Memory Allocator"
+ depends on HAVE_DMA_CONTIGUOUS && CMA
+ help
+ This enables the Contiguous Memory Allocator which allows drivers
+ to allocate big physically-contiguous blocks of memory for use with
+ hardware components that do not support I/O map nor scatter-gather.
+
+ You can disable CMA by specifying "cma=0" on the kernel's command
+ line.
+
+ For more information see <include/linux/dma-contiguous.h>.
+ If unsure, say "n".
+
+if DMA_CMA
+comment "Default contiguous memory area size:"
+
+config CMA_SIZE_MBYTES
+ int "Size in Mega Bytes"
+ depends on !CMA_SIZE_SEL_PERCENTAGE
+ default 0 if X86
+ default 16
+ help
+ Defines the size (in MiB) of the default memory area for Contiguous
+ Memory Allocator. If the size of 0 is selected, CMA is disabled by
+ default, but it can be enabled by passing cma=size[MG] to the kernel.
+
+
+config CMA_SIZE_PERCENTAGE
+ int "Percentage of total memory"
+ depends on !CMA_SIZE_SEL_MBYTES
+ default 0 if X86
+ default 10
+ help
+ Defines the size of the default memory area for Contiguous Memory
+ Allocator as a percentage of the total memory in the system.
+ If 0 percent is selected, CMA is disabled by default, but it can be
+ enabled by passing cma=size[MG] to the kernel.
+
+choice
+ prompt "Selected region size"
+ default CMA_SIZE_SEL_MBYTES
+
+config CMA_SIZE_SEL_MBYTES
+ bool "Use mega bytes value only"
+
+config CMA_SIZE_SEL_PERCENTAGE
+ bool "Use percentage value only"
+
+config CMA_SIZE_SEL_MIN
+ bool "Use lower value (minimum)"
+
+config CMA_SIZE_SEL_MAX
+ bool "Use higher value (maximum)"
+
+endchoice
+
+config CMA_ALIGNMENT
+ int "Maximum PAGE_SIZE order of alignment for contiguous buffers"
+ range 4 12
+ default 8
+ help
+ DMA mapping framework by default aligns all buffers to the smallest
+ PAGE_SIZE order which is greater than or equal to the requested buffer
+ size. This works well for buffers up to a few hundreds kilobytes, but
+ for larger buffers it just a memory waste. With this parameter you can
+ specify the maximum PAGE_SIZE order for contiguous buffers. Larger
+ buffers will be aligned only to this specified order. The order is
+ expressed as a power of two multiplied by the PAGE_SIZE.
+
+ For example, if your system defaults to 4KiB pages, the order value
+ of 8 means that the buffers will be aligned up to 1MiB only.
+
+ If unsure, leave the default value "8".
+
+endif
This is where all the related code already lives. Signed-off-by: Christoph Hellwig <hch@lst.de> --- drivers/base/Kconfig | 77 -------------------------------------------- kernel/dma/Kconfig | 77 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 77 insertions(+), 77 deletions(-)