diff mbox series

ASoC: rt1308: Add RT1308 amplifier driver

Message ID 20190416022246.10121-1-derek.fang@realtek.com (mailing list archive)
State New, archived
Headers show
Series ASoC: rt1308: Add RT1308 amplifier driver | expand

Commit Message

Derek [方德義] April 16, 2019, 2:22 a.m. UTC
From: Derek Fang <derek.fang@realtek.com>

This is the initial amplifier driver for rt1308.

Signed-off-by: Derek Fang <derek.fang@realtek.com>
---
 sound/soc/codecs/rt1308.c | 915 ++++++++++++++++++++++++++++++++++++++
 sound/soc/codecs/rt1308.h | 291 ++++++++++++
 2 files changed, 1206 insertions(+)
 create mode 100755 sound/soc/codecs/rt1308.c
 create mode 100755 sound/soc/codecs/rt1308.h

Comments

Mark Brown April 17, 2019, 3:05 p.m. UTC | #1
On Wed, Apr 17, 2019 at 11:40:28AM +0000, Derek [方德義] wrote:

Please fix your mail client to word wrap within paragraphs at something
substantially less than 80 columns.  Doing this makes your messages much
easier to read and reply to.

> > The ones here with comments look an awful lot like they're system specific config
> > which should be left up to either platform data (or DT/ACPI configuration) or
> > done at runtime (like gains).  Some of the others like the pads configuration
> > might also fit into that.

> We don't open the DA gain setting for user at runtime, so have to set
> a default level in the init list. 

That's not the way Linux drivers generally work...  is there some
technical reason for that or is it just some kind of policy decision?

> > > +static void rt1308_reset(struct regmap *regmap) {
> > > +	regmap_write(regmap, RT1308_RESET, 0); }
> > 
> > If we do need the init list shouldn't we also do a reninit every time we do a reset?

> The init list is only set at driver probe, not every time after resetting.

This is what I'm pointing out; if you don't restore these values then
why set them at all?
Derek [方德義] April 23, 2019, 1:39 p.m. UTC | #2
> 
> On Wed, Apr 17, 2019 at 11:40:28AM +0000, Derek wrote:
> 
> Please fix your mail client to word wrap within paragraphs at something
> substantially less than 80 columns.  Doing this makes your messages much
> easier to read and reply to.
> 
> > > The ones here with comments look an awful lot like they're system
> > > specific config which should be left up to either platform data (or
> > > DT/ACPI configuration) or done at runtime (like gains).  Some of the
> > > others like the pads configuration might also fit into that.
> 
> > We don't open the DA gain setting for user at runtime, so have to set
> > a default level in the init list.
> 
> That's not the way Linux drivers generally work...  is there some technical reason
> for that or is it just some kind of policy decision?

Maybe I could add a gain control for the user and set the gain to safety max level in init list for speaker protection.

> 
> > > > +static void rt1308_reset(struct regmap *regmap) {
> > > > +	regmap_write(regmap, RT1308_RESET, 0); }
> > >
> > > If we do need the init list shouldn't we also do a reninit every time we do a
> reset?
> 
> > The init list is only set at driver probe, not every time after resetting.
> 
> This is what I'm pointing out; if you don't restore these values then why set them
> at all?

OK, I could reinit after every time resetting.

> ------Please consider the environment before printing this e-mail.
Mark Brown May 8, 2019, 6:45 a.m. UTC | #3
On Tue, Apr 23, 2019 at 01:39:59PM +0000, Derek [方德義] wrote:

> > On Wed, Apr 17, 2019 at 11:40:28AM +0000, Derek wrote:

> > Please fix your mail client to word wrap within paragraphs at something
> > substantially less than 80 columns.  Doing this makes your messages much
> > easier to read and reply to.

Please don't ignore review comments, people are generally making them
for a reason and are likely to have the same concerns if issues remain
unaddressed.  Having to repeat the same comments can get repetitive and
make people question the value of time spent reviewing.  If you disagree
with the review comments that's fine but you need to reply and discuss
your concerns so that the reviewer can understand your decisions.

> > > > The ones here with comments look an awful lot like they're system
> > > > specific config which should be left up to either platform data (or
> > > > DT/ACPI configuration) or done at runtime (like gains).  Some of the
> > > > others like the pads configuration might also fit into that.

> > > We don't open the DA gain setting for user at runtime, so have to set
> > > a default level in the init list.

> > That's not the way Linux drivers generally work...  is there some technical reason
> > for that or is it just some kind of policy decision?

> Maybe I could add a gain control for the user and set the gain to safety max level in init list for speaker protection.

The maximum volume can be limited with snd_soc_limit_volume() but if the
limit is for the speaker then that's machine dependent anyway.
Derek [方德義] May 8, 2019, 1:17 p.m. UTC | #4
> Subject: Re: [PATCH] ASoC: rt1308: Add RT1308 amplifier driver
> 
> On Tue, Apr 23, 2019 at 01:39:59PM +0000, Derek wrote:
> 
> > > On Wed, Apr 17, 2019 at 11:40:28AM +0000, Derek wrote:
> 
> > > Please fix your mail client to word wrap within paragraphs at
> > > something substantially less than 80 columns.  Doing this makes your
> > > messages much easier to read and reply to.

Sorry for the neglect of mail format. I will pay attention.

> Please don't ignore review comments, people are generally making them for a
> reason and are likely to have the same concerns if issues remain 
> unaddressed.
> Having to repeat the same comments can get repetitive and make people
> question the value of time spent reviewing.  If you disagree with the review
> comments that's fine but you need to reply and discuss your concerns so that
> the reviewer can understand your decisions.
> 
> > > > > The ones here with comments look an awful lot like they're
> > > > > system specific config which should be left up to either
> > > > > platform data (or DT/ACPI configuration) or done at runtime
> > > > > (like gains).  Some of the others like the pads configuration might
> > > > > also fit into that.
> 
> > > > We don't open the DA gain setting for user at runtime, so have to
> > > > set a default level in the init list.
> 
> > > That's not the way Linux drivers generally work...  is there some
> > > technical reason for that or is it just some kind of policy decision?
> 
> > Maybe I could add a gain control for the user and set the gain to safety
> >  max level in init list for speaker protection.
> 
> The maximum volume can be limited with snd_soc_limit_volume() but if the
>  limit is for the speaker then that's machine dependent anyway.

The maximum volume setting is temporarily not machine dependent.
It avoids harming if any machine doesn't set the limit volume.


> ------Please consider the environment before printing this e-mail.
Mark Brown May 12, 2019, 8:06 a.m. UTC | #5
On Wed, May 08, 2019 at 01:17:54PM +0000, Derek [方德義] wrote:

> > The maximum volume can be limited with snd_soc_limit_volume() but if the
> >  limit is for the speaker then that's machine dependent anyway.

> The maximum volume setting is temporarily not machine dependent.
> It avoids harming if any machine doesn't set the limit volume.

I'm confused about what this limit is - is it just some arbatrary limit
imposed in case some board has problems or is it an actual limit that
comes from the chip?  If it's a "just in case" limit then the board
should be the one doing the limiting, yes people can break things but
it's difficult to get decision like that done sensibly in the CODEC
driver in a way that works for everything and the general expectation is
that this is all for use by system integrators rather than end users.
Derek [方德義] May 13, 2019, 1:54 p.m. UTC | #6
> Subject: Re: [PATCH] ASoC: rt1308: Add RT1308 amplifier driver
> 
> On Wed, May 08, 2019 at 01:17:54PM +0000, Derek wrote:
> 
> > > The maximum volume can be limited with snd_soc_limit_volume() but if the
> > >  limit is for the speaker then that's machine dependent anyway.
> 
> > The maximum volume setting is temporarily not machine dependent.
> > It avoids harming if any machine doesn't set the limit volume.
> 
> I'm confused about what this limit is - is it just some arbatrary limit
> imposed in case some board has problems or is it an actual limit that
> comes from the chip?  If it's a "just in case" limit then the board
> should be the one doing the limiting, yes people can break things but
> it's difficult to get decision like that done sensibly in the CODEC
> driver in a way that works for everything and the general expectation is
> that this is all for use by system integrators rather than end users.

It is an actual limit that comes from the chip.

> 
> ------Please consider the environment before printing this e-mail.
Mark Brown May 13, 2019, 2:56 p.m. UTC | #7
On Mon, May 13, 2019 at 01:54:08PM +0000, Derek [方德義] wrote:

> > I'm confused about what this limit is - is it just some arbatrary limit
> > imposed in case some board has problems or is it an actual limit that
> > comes from the chip?  If it's a "just in case" limit then the board
> > should be the one doing the limiting, yes people can break things but
> > it's difficult to get decision like that done sensibly in the CODEC
> > driver in a way that works for everything and the general expectation is
> > that this is all for use by system integrators rather than end users.

> It is an actual limit that comes from the chip.

If there is an actual limit in the chip the driver just shouldn't expose
anything beyond what that limit is - the original thing I was calling
out was that you're just hard coding a value for this setting into the
driver, that just means that the expectation is that the values should
be user settable within whatever the chip can support.  If there's
settings that can't be supported at all the driver doesn't need to
pretend to offer them.
Derek [方德義] May 14, 2019, 11:10 a.m. UTC | #8
> Subject: Re: [PATCH] ASoC: rt1308: Add RT1308 amplifier driver
> 
> On Mon, May 13, 2019 at 01:54:08PM +0000, Derek wrote:
> 
> > > I'm confused about what this limit is - is it just some arbatrary limit
> > > imposed in case some board has problems or is it an actual limit that
> > > comes from the chip?  If it's a "just in case" limit then the board
> > > should be the one doing the limiting, yes people can break things but
> > > it's difficult to get decision like that done sensibly in the CODEC
> > > driver in a way that works for everything and the general expectation is
> > > that this is all for use by system integrators rather than end users.
> 
> > It is an actual limit that comes from the chip.
> 
> If there is an actual limit in the chip the driver just shouldn't expose
> anything beyond what that limit is - the original thing I was calling
> out was that you're just hard coding a value for this setting into the
> driver, that just means that the expectation is that the values should
> be user settable within whatever the chip can support.  If there's
> settings that can't be supported at all the driver doesn't need to
> pretend to offer them.

I could remove comment for the limit setting in register patch/init list
to avoid users or integrators have any expectation.
And also there will not be any support at all the driver according to the
limit setting.
 
> ------Please consider the environment before printing this e-mail.
Mark Brown May 15, 2019, 4:14 p.m. UTC | #9
On Tue, May 14, 2019 at 11:10:58AM +0000, Derek [方德義] wrote:

> I could remove comment for the limit setting in register patch/init list
> to avoid users or integrators have any expectation.
> And also there will not be any support at all the driver according to the
> limit setting.

It's better to have a comment than not have one, I think I'd be happier
if I understood what was actually being limited here - that might make
it clear why it's not system specific which is what's concerning me.
Derek [方德義] May 16, 2019, 1:46 p.m. UTC | #10
> Subject: Re: [PATCH] ASoC: rt1308: Add RT1308 amplifier driver
> 
> On Tue, May 14, 2019 at 11:10:58AM +0000, Derek [方德義] wrote:
> 
> > I could remove comment for the limit setting in register patch/init list
> > to avoid users or integrators have any expectation.
> > And also there will not be any support at all the driver according to the
> > limit setting.
> 
> It's better to have a comment than not have one, I think I'd be happier
> if I understood what was actually being limited here - that might make
> it clear why it's not system specific which is what's concerning me.

I will give a comment that describes the limit setting reason clearly.

> ------Please consider the environment before printing this e-mail.
Mark Brown May 16, 2019, 4:52 p.m. UTC | #11
On Thu, May 16, 2019 at 01:46:53PM +0000, Derek [方德義] wrote:

> > It's better to have a comment than not have one, I think I'd be happier
> > if I understood what was actually being limited here - that might make
> > it clear why it's not system specific which is what's concerning me.

> I will give a comment that describes the limit setting reason clearly.

OK.
diff mbox series

Patch

diff --git a/sound/soc/codecs/rt1308.c b/sound/soc/codecs/rt1308.c
new file mode 100755
index 000000000000..e7a716470cb9
--- /dev/null
+++ b/sound/soc/codecs/rt1308.c
@@ -0,0 +1,915 @@ 
+/*
+ * rt1308.c  --  RT1308 ALSA SoC amplifier component driver
+ *
+ * Copyright 2019 Realtek Semiconductor Corp.
+ * Author: Derek Fang <derek.fang@realtek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/firmware.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/soc-dapm.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+
+#include "rl6231.h"
+#include "rt1308.h"
+
+static const struct reg_sequence init_list[] = {
+
+	{ RT1308_I2C_I2S_SDW_SET,	0x01014005 },
+	{ RT1308_CLASS_D_SET_2,		0x227f5501 },
+	{ RT1308_PADS_1,		0x50150505 },
+	{ RT1308_VREF,			0x18100000 },
+	{ RT1308_IV_SENSE,		0x87010000 },
+	{ RT1308_DUMMY_REG,		0x00000200 },
+	{ RT1308_SIL_DET,		0x61c30000 },
+	{ RT1308_CLK_DET,		0x01000000 },  // detect BCLK
+
+	{ RT1308_DAC_SET,		0xafaf0700 },  // DA gain L/R < -9dB
+
+};
+#define RT1308_INIT_REG_LEN ARRAY_SIZE(init_list)
+
+struct rt1308_priv {
+	struct snd_soc_component *component;
+	struct regmap *regmap;
+
+	int sysclk;
+	int sysclk_src;
+	int lrck;
+	int bclk;
+	int master;
+
+	int pll_src;
+	int pll_in;
+	int pll_out;
+};
+
+static const struct reg_default rt1308_reg[] = {
+
+	{ 0x01, 0x1f3f5f00 },
+	{ 0x02, 0x07000000 },
+	{ 0x03, 0x80003e00 },
+	{ 0x04, 0x80800600 },
+	{ 0x05, 0x0aaa1a0a },
+	{ 0x06, 0x52000000 },
+	{ 0x07, 0x00000000 },
+	{ 0x08, 0x00600000 },
+	{ 0x09, 0xe1030000 },
+	{ 0x0a, 0x00000000 },
+	{ 0x0b, 0x30000000 },
+	{ 0x0c, 0x7fff7000 },
+	{ 0x10, 0xffff0700 },
+	{ 0x11, 0x0a000000 },
+	{ 0x12, 0x60040000 },
+	{ 0x13, 0x00000000 },
+	{ 0x14, 0x0f300000 },
+	{ 0x15, 0x00000022 },
+	{ 0x16, 0x02000000 },
+	{ 0x17, 0x01004045 },
+	{ 0x18, 0x00000000 },
+	{ 0x19, 0x00000000 },
+	{ 0x1a, 0x80000000 },
+	{ 0x1b, 0x10325476 },
+	{ 0x1c, 0x1d1d0000 },
+	{ 0x20, 0xd2101300 },
+	{ 0x21, 0xf3ffff00 },
+	{ 0x22, 0x00000000 },
+	{ 0x23, 0x00000000 },
+	{ 0x24, 0x00000000 },
+	{ 0x25, 0x00000000 },
+	{ 0x26, 0x00000000 },
+	{ 0x27, 0x00000000 },
+	{ 0x28, 0x00000000 },
+	{ 0x29, 0x00000000 },
+	{ 0x2a, 0x00000000 },
+	{ 0x2b, 0x00000000 },
+	{ 0x2c, 0x00000000 },
+	{ 0x2d, 0x00000000 },
+	{ 0x2e, 0x00000000 },
+	{ 0x2f, 0x00000000 },
+	{ 0x30, 0x01000000 },
+	{ 0x31, 0x20025501 },
+	{ 0x32, 0x00000000 },
+	{ 0x33, 0x105a0000 },
+	{ 0x34, 0x10100000 },
+	{ 0x35, 0x2aaa52aa },
+	{ 0x36, 0x00c00000 },
+	{ 0x37, 0x20046100 },
+	{ 0x50, 0x10022f00 },
+	{ 0x51, 0x003c0000 },
+	{ 0x54, 0x04000000 },
+	{ 0x55, 0x01000000 },
+	{ 0x56, 0x02000000 },
+	{ 0x57, 0x02000000 },
+	{ 0x58, 0x02000000 },
+	{ 0x59, 0x02000000 },
+	{ 0x5b, 0x02000000 },
+	{ 0x5c, 0x00000000 },
+	{ 0x5d, 0x00000000 },
+	{ 0x5e, 0x00000000 },
+	{ 0x5f, 0x00000000 },
+	{ 0x60, 0x02000000 },
+	{ 0x61, 0x00000000 },
+	{ 0x62, 0x00000000 },
+	{ 0x63, 0x00000000 },
+	{ 0x64, 0x00000000 },
+	{ 0x65, 0x02000000 },
+	{ 0x66, 0x00000000 },
+	{ 0x67, 0x00000000 },
+	{ 0x68, 0x00000000 },
+	{ 0x69, 0x00000000 },
+	{ 0x6a, 0x02000000 },
+	{ 0x6c, 0x00000000 },
+	{ 0x6d, 0x00000000 },
+	{ 0x6e, 0x00000000 },
+	{ 0x70, 0x10EC1308 },
+	{ 0x71, 0x00000000 },
+	{ 0x72, 0x00000000 },
+	{ 0x73, 0x00000000 },
+	{ 0x74, 0x00000000 },
+	{ 0x75, 0x00000000 },
+	{ 0x76, 0x00000000 },
+	{ 0x77, 0x00000000 },
+	{ 0x78, 0x00000000 },
+	{ 0x79, 0x00000000 },
+	{ 0x7a, 0x00000000 },
+	{ 0x7b, 0x00000000 },
+	{ 0x7c, 0x00000000 },
+	{ 0x7d, 0x00000000 },
+	{ 0x7e, 0x00000000 },
+	{ 0x7f, 0x00020f00 },
+	{ 0x80, 0x00000000 },
+	{ 0x81, 0x00000000 },
+	{ 0x82, 0x00000000 },
+	{ 0x83, 0x00000000 },
+	{ 0x84, 0x00000000 },
+	{ 0x85, 0x00000000 },
+	{ 0x86, 0x00000000 },
+	{ 0x87, 0x00000000 },
+	{ 0x88, 0x00000000 },
+	{ 0x89, 0x00000000 },
+	{ 0x8a, 0x00000000 },
+	{ 0x8b, 0x00000000 },
+	{ 0x8c, 0x00000000 },
+	{ 0x8d, 0x00000000 },
+	{ 0x8e, 0x00000000 },
+	{ 0x90, 0x50250905 },
+	{ 0x91, 0x15050000 },
+	{ 0xa0, 0x00000000 },
+	{ 0xa1, 0x00000000 },
+	{ 0xa2, 0x00000000 },
+	{ 0xa3, 0x00000000 },
+	{ 0xa4, 0x00000000 },
+	{ 0xb0, 0x00000000 },
+	{ 0xb1, 0x00000000 },
+	{ 0xb2, 0x00000000 },
+	{ 0xb3, 0x00000000 },
+	{ 0xb4, 0x00000000 },
+	{ 0xb5, 0x00000000 },
+	{ 0xb6, 0x00000000 },
+	{ 0xb7, 0x00000000 },
+	{ 0xb8, 0x00000000 },
+	{ 0xb9, 0x00000000 },
+	{ 0xba, 0x00000000 },
+	{ 0xbb, 0x00000000 },
+	{ 0xc0, 0x01000000 },
+	{ 0xc1, 0x00000000 },
+	{ 0xf0, 0x00000000 },
+};
+
+static int rt1308_reg_init(struct snd_soc_component *component)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+
+	regmap_multi_reg_write(rt1308->regmap, init_list, RT1308_INIT_REG_LEN);
+	return 0;
+}
+
+static bool rt1308_volatile_register(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case RT1308_RESET:
+	case RT1308_RESET_N:
+	case RT1308_CLK_2:
+	case RT1308_SIL_DET:
+	case RT1308_CLK_DET:
+	case RT1308_DC_DET:
+	case RT1308_SDW_REG_RDATA:
+	case RT1308_DC_CAL_1:
+	case RT1308_PVDD_OFFSET_CTL:
+	case RT1308_CAL_OFFSET_DAC_PBTL:
+	case RT1308_CAL_OFFSET_DAC_L:
+	case RT1308_CAL_OFFSET_DAC_R:
+	case RT1308_CAL_OFFSET_PWM_L:
+	case RT1308_CAL_OFFSET_PWM_R:
+	case RT1308_CAL_PWM_VOS_ADC_L:
+	case RT1308_CAL_PWM_VOS_ADC_R:
+	case RT1308_POWER_STATUS:
+	case RT1308_POWER_INT:
+	case RT1308_SINE_TONE_GEN_2:
+	case RT1308_BQ_SET:
+	case RT1308_BQ_PARA_UPDATE:
+	case RT1308_VEN_DEV_ID:
+	case RT1308_VERSION_ID:
+	case RT1308_EFUSE_1:
+	case RT1308_EFUSE_READ_PVDD_L:
+	case RT1308_EFUSE_READ_PVDD_R:
+	case RT1308_EFUSE_READ_PVDD_PTBL:
+	case RT1308_EFUSE_READ_DEV:
+	case RT1308_EFUSE_READ_R0:
+	case RT1308_EFUSE_READ_ADC_L:
+	case RT1308_EFUSE_READ_ADC_R:
+	case RT1308_EFUSE_READ_ADC_PBTL:
+	case RT1308_EFUSE_RESERVE:
+	case RT1308_EFUSE_DATA_0_MSB:
+	case RT1308_EFUSE_DATA_0_LSB:
+	case RT1308_EFUSE_DATA_1_MSB:
+	case RT1308_EFUSE_DATA_1_LSB:
+	case RT1308_EFUSE_DATA_2_MSB:
+	case RT1308_EFUSE_DATA_2_LSB:
+	case RT1308_EFUSE_DATA_3_MSB:
+	case RT1308_EFUSE_DATA_3_LSB:
+	case RT1308_EFUSE_STATUS_1:
+	case RT1308_EFUSE_STATUS_2:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool rt1308_readable_register(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case RT1308_RESET:
+	case RT1308_RESET_N:
+	case RT1308_CLK_GATING ... RT1308_DC_DET_THRES:
+	case RT1308_DAC_SET ... RT1308_AD_FILTER_SET:
+	case RT1308_DC_CAL_1 ... RT1308_POWER_INT:
+	case RT1308_SINE_TONE_GEN_1:
+	case RT1308_SINE_TONE_GEN_2:
+	case RT1308_BQ_SET:
+	case RT1308_BQ_PARA_UPDATE:
+	case RT1308_BQ_PRE_VOL_L ... RT1308_BQ_POST_VOL_R:
+	case RT1308_BQ1_L_H0 ... RT1308_BQ2_R_A2:
+	case RT1308_VEN_DEV_ID:
+	case RT1308_VERSION_ID:
+	case RT1308_SPK_BOUND:
+	case RT1308_BQ1_EQ_L_1 ... RT1308_BQ2_EQ_R_3:
+	case RT1308_EFUSE_1 ... RT1308_EFUSE_RESERVE:
+	case RT1308_PADS_1:
+	case RT1308_PADS_2:
+	case RT1308_TEST_MODE:
+	case RT1308_TEST_1:
+	case RT1308_TEST_2:
+	case RT1308_TEST_3:
+	case RT1308_TEST_4:
+	case RT1308_EFUSE_DATA_0_MSB ... RT1308_EFUSE_STATUS_2:
+	case RT1308_TCON_1:
+	case RT1308_TCON_2:
+	case RT1308_DUMMY_REG:
+	case RT1308_MAX_REG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static void rt1308_reset(struct regmap *regmap)
+{
+	regmap_write(regmap, RT1308_RESET, 0);
+}
+
+static int rt1308_classd_event(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		msleep(30);
+		snd_soc_component_update_bits(component, RT1308_POWER_STATUS,
+			RT1308_POW_PDB_REG_BIT, RT1308_POW_PDB_REG_BIT);
+		msleep(40);
+		break;
+	case SND_SOC_DAPM_PRE_PMD:
+		snd_soc_component_update_bits(component, RT1308_POWER_STATUS,
+			RT1308_POW_PDB_REG_BIT, 0);
+		usleep_range(150000, 200000);
+		break;
+
+	default:
+		return 0;
+	}
+
+	return 0;
+}
+
+static const char * const rt1308_rx_data_ch_select[] = {
+	"LR",
+	"LL",
+	"RL",
+	"RR",
+};
+
+static SOC_ENUM_SINGLE_DECL(rt1308_rx_data_ch_enum, RT1308_DATA_PATH, 24,
+	rt1308_rx_data_ch_select);
+
+static const struct snd_kcontrol_new rt1308_snd_controls[] = {
+
+	/* I2S Data Channel Selection */
+	SOC_ENUM("RX Channel Select", rt1308_rx_data_ch_enum),
+};
+
+static const struct snd_kcontrol_new rt1308_sto_dac_l =
+	SOC_DAPM_SINGLE("Switch", RT1308_DAC_SET,
+		RT1308_DVOL_MUTE_L_EN_SFT, 1, 1);
+
+static const struct snd_kcontrol_new rt1308_sto_dac_r =
+	SOC_DAPM_SINGLE("Switch", RT1308_DAC_SET,
+		RT1308_DVOL_MUTE_R_EN_SFT, 1, 1);
+
+static const struct snd_soc_dapm_widget rt1308_dapm_widgets[] = {
+	/* Audio Interface */
+	SND_SOC_DAPM_AIF_IN("AIF1RX", "AIF1 Playback", 0, SND_SOC_NOPM, 0, 0),
+
+	/* Supply Widgets */
+	SND_SOC_DAPM_SUPPLY("MBIAS20U", RT1308_POWER,
+		RT1308_POW_MBIAS20U_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("ALDO", RT1308_POWER,
+		RT1308_POW_ALDO_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("DBG", RT1308_POWER,
+		RT1308_POW_DBG_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("DACL", RT1308_POWER,
+		RT1308_POW_DACL_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("CLK25M", RT1308_POWER,
+		RT1308_POW_CLK25M_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("ADC_R", RT1308_POWER,
+		RT1308_POW_ADC_R_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("ADC_L", RT1308_POWER,
+		RT1308_POW_ADC_L_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("DLDO", RT1308_POWER,
+		RT1308_POW_DLDO_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("VREF", RT1308_POWER,
+		RT1308_POW_VREF_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("MIXER_R", RT1308_POWER,
+		RT1308_POW_MIXER_R_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("MIXER_L", RT1308_POWER,
+		RT1308_POW_MIXER_L_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("MBIAS4U", RT1308_POWER,
+		RT1308_POW_MBIAS4U_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL2_LDO", RT1308_POWER,
+		RT1308_POW_PLL2_LDO_EN_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL2B", RT1308_POWER,
+		RT1308_POW_PLL2B_EN_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL2F", RT1308_POWER,
+		RT1308_POW_PLL2F_EN_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL2F2", RT1308_POWER,
+		RT1308_POW_PLL2F2_EN_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_SUPPLY("PLL2B2", RT1308_POWER,
+		RT1308_POW_PLL2B2_EN_BIT, 0, NULL, 0),
+
+	/* Digital Interface */
+	SND_SOC_DAPM_SUPPLY("DAC Power", RT1308_POWER,
+		RT1308_POW_DAC1_BIT, 0, NULL, 0),
+	SND_SOC_DAPM_DAC("DAC", NULL, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_SWITCH("DAC L", SND_SOC_NOPM, 0, 0, &rt1308_sto_dac_l),
+	SND_SOC_DAPM_SWITCH("DAC R", SND_SOC_NOPM, 0, 0, &rt1308_sto_dac_r),
+
+	/* Output Lines */
+	SND_SOC_DAPM_PGA_E("CLASS D", SND_SOC_NOPM, 0, 0, NULL, 0,
+		rt1308_classd_event,
+		SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU),
+	SND_SOC_DAPM_OUTPUT("SPOL"),
+	SND_SOC_DAPM_OUTPUT("SPOR"),
+};
+
+static const struct snd_soc_dapm_route rt1308_dapm_routes[] = {
+
+	{ "DAC", NULL, "AIF1RX" },
+
+	{ "DAC", NULL, "MBIAS20U" },
+	{ "DAC", NULL, "ALDO" },
+	{ "DAC", NULL, "DBG" },
+	{ "DAC", NULL, "DACL" },
+	{ "DAC", NULL, "CLK25M" },
+	{ "DAC", NULL, "ADC_R" },
+	{ "DAC", NULL, "ADC_L" },
+	{ "DAC", NULL, "DLDO" },
+	{ "DAC", NULL, "VREF" },
+	{ "DAC", NULL, "MIXER_R" },
+	{ "DAC", NULL, "MIXER_L" },
+	{ "DAC", NULL, "MBIAS4U" },
+	{ "DAC", NULL, "PLL2_LDO" },
+	{ "DAC", NULL, "PLL2B" },
+	{ "DAC", NULL, "PLL2F" },
+	{ "DAC", NULL, "PLL2F2" },
+	{ "DAC", NULL, "PLL2B2" },
+
+	{ "DAC L", "Switch", "DAC" },
+	{ "DAC R", "Switch", "DAC" },
+	{ "DAC L", NULL, "DAC Power" },
+	{ "DAC R", NULL, "DAC Power" },
+
+	{ "CLASS D", NULL, "DAC L" },
+	{ "CLASS D", NULL, "DAC R" },
+	{ "SPOL", NULL, "CLASS D" },
+	{ "SPOR", NULL, "CLASS D" },
+};
+
+static int rt1308_get_clk_info(int sclk, int rate)
+{
+	int i, pd[] = {1, 2, 3, 4, 6, 8, 12, 16};
+
+	if (sclk <= 0 || rate <= 0)
+		return -EINVAL;
+
+	rate = rate << 8;
+	for (i = 0; i < ARRAY_SIZE(pd); i++)
+		if (sclk == rate * pd[i])
+			return i;
+
+	return -EINVAL;
+}
+
+static int rt1308_hw_params(struct snd_pcm_substream *substream,
+	struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+	struct snd_soc_component *component = dai->component;
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+	unsigned int val_len = 0, val_clk, mask_clk;
+	int pre_div, bclk_ms, frame_size;
+
+	rt1308->lrck = params_rate(params);
+	pre_div = rt1308_get_clk_info(rt1308->sysclk, rt1308->lrck);
+	if (pre_div < 0) {
+		dev_err(component->dev,
+			"Unsupported clock setting %d\n", rt1308->lrck);
+		return -EINVAL;
+	}
+
+	frame_size = snd_soc_params_to_frame_size(params);
+	if (frame_size < 0) {
+		dev_err(component->dev, "Unsupported frame size: %d\n",
+			frame_size);
+		return -EINVAL;
+	}
+
+	bclk_ms = frame_size > 32;
+	rt1308->bclk = rt1308->lrck * (32 << bclk_ms);
+
+	dev_dbg(component->dev, "bclk_ms is %d and pre_div is %d for iis %d\n",
+				bclk_ms, pre_div, dai->id);
+
+	dev_dbg(component->dev, "lrck is %dHz and pre_div is %d for iis %d\n",
+				rt1308->lrck, pre_div, dai->id);
+
+	switch (params_width(params)) {
+	case 16:
+		val_len |= RT1308_I2S_DL_SEL_16B;
+		break;
+	case 20:
+		val_len |= RT1308_I2S_DL_SEL_20B;
+		break;
+	case 24:
+		val_len |= RT1308_I2S_DL_SEL_24B;
+		break;
+	case 8:
+		val_len |= RT1308_I2S_DL_SEL_8B;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (dai->id) {
+	case RT1308_AIF1:
+		mask_clk = RT1308_DIV_FS_SYS_MASK;
+		val_clk = pre_div << RT1308_DIV_FS_SYS_SFT;
+		snd_soc_component_update_bits(component,
+			RT1308_I2S_SET_2, RT1308_I2S_DL_SEL_MASK,
+			val_len);
+		break;
+	default:
+		dev_err(component->dev, "Invalid dai->id: %d\n", dai->id);
+		return -EINVAL;
+	}
+
+	snd_soc_component_update_bits(component, RT1308_CLK_1,
+		mask_clk, val_clk);
+
+	return 0;
+}
+
+static int rt1308_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	struct snd_soc_component *component = dai->component;
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+	unsigned int reg_val = 0, reg1_val = 0;
+
+	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+	case SND_SOC_DAIFMT_CBS_CFS:
+		rt1308->master = 0;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+		break;
+	case SND_SOC_DAIFMT_LEFT_J:
+		reg_val |= RT1308_I2S_DF_SEL_LEFT;
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		reg_val |= RT1308_I2S_DF_SEL_PCM_A;
+		break;
+	case SND_SOC_DAIFMT_DSP_B:
+		reg_val |= RT1308_I2S_DF_SEL_PCM_B;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		reg1_val |= RT1308_I2S_BCLK_INV;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (dai->id) {
+	case RT1308_AIF1:
+		snd_soc_component_update_bits(component,
+			RT1308_I2S_SET_1, RT1308_I2S_DF_SEL_MASK,
+			reg_val);
+		snd_soc_component_update_bits(component,
+			RT1308_I2S_SET_2, RT1308_I2S_BCLK_MASK,
+			reg1_val);
+		break;
+	default:
+		dev_err(component->dev, "Invalid dai->id: %d\n", dai->id);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static int rt1308_set_component_sysclk(struct snd_soc_component *component,
+		int clk_id, int source, unsigned int freq, int dir)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+	unsigned int reg_val = 0;
+
+	if (freq == rt1308->sysclk && clk_id == rt1308->sysclk_src)
+		return 0;
+
+	switch (clk_id) {
+	case RT1308_FS_SYS_S_MCLK:
+		reg_val |= RT1308_SEL_FS_SYS_SRC_MCLK;
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_DET, RT1308_MCLK_DET_EN_MASK,
+			RT1308_MCLK_DET_EN);
+		break;
+	case RT1308_FS_SYS_S_BCLK:
+		reg_val |= RT1308_SEL_FS_SYS_SRC_BCLK;
+		break;
+	case RT1308_FS_SYS_S_PLL:
+		reg_val |= RT1308_SEL_FS_SYS_SRC_PLL;
+		break;
+	case RT1308_FS_SYS_S_RCCLK:
+		reg_val |= RT1308_SEL_FS_SYS_SRC_RCCLK;
+		break;
+	default:
+		dev_err(component->dev, "Invalid clock id (%d)\n", clk_id);
+		return -EINVAL;
+	}
+	snd_soc_component_update_bits(component, RT1308_CLK_1,
+		RT1308_SEL_FS_SYS_MASK, reg_val);
+	rt1308->sysclk = freq;
+	rt1308->sysclk_src = clk_id;
+
+	dev_dbg(component->dev, "Sysclk is %dHz and clock id is %d\n",
+		freq, clk_id);
+
+	return 0;
+}
+
+static int rt1308_set_component_pll(struct snd_soc_component *component,
+		int pll_id, int source, unsigned int freq_in,
+		unsigned int freq_out)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+	struct rl6231_pll_code pll_code;
+	int ret;
+
+	if (source == rt1308->pll_src && freq_in == rt1308->pll_in &&
+	    freq_out == rt1308->pll_out)
+		return 0;
+
+	if (!freq_in || !freq_out) {
+		dev_dbg(component->dev, "PLL disabled\n");
+
+		rt1308->pll_in = 0;
+		rt1308->pll_out = 0;
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_1, RT1308_SEL_FS_SYS_MASK,
+			RT1308_SEL_FS_SYS_SRC_MCLK);
+		return 0;
+	}
+
+	switch (source) {
+	case RT1308_PLL_S_MCLK:
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_2, RT1308_SEL_PLL_SRC_MASK,
+			RT1308_SEL_PLL_SRC_MCLK);
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_DET, RT1308_MCLK_DET_EN_MASK,
+			RT1308_MCLK_DET_EN);
+		break;
+	case RT1308_PLL_S_BCLK:
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_2, RT1308_SEL_PLL_SRC_MASK,
+			RT1308_SEL_PLL_SRC_BCLK);
+		break;
+	case RT1308_PLL_S_RCCLK:
+		snd_soc_component_update_bits(component,
+			RT1308_CLK_2, RT1308_SEL_PLL_SRC_MASK,
+			RT1308_SEL_PLL_SRC_RCCLK);
+		freq_in = 25000000;
+		break;
+	default:
+		dev_err(component->dev, "Unknown PLL Source %d\n", source);
+		return -EINVAL;
+	}
+
+	ret = rl6231_pll_calc(freq_in, freq_out, &pll_code);
+	if (ret < 0) {
+		dev_err(component->dev, "Unsupport input clock %d\n", freq_in);
+		return ret;
+	}
+
+	dev_dbg(component->dev, "bypass=%d m=%d n=%d k=%d\n",
+		pll_code.m_bp, (pll_code.m_bp ? 0 : pll_code.m_code),
+		pll_code.n_code, pll_code.k_code);
+
+	snd_soc_component_write(component, RT1308_PLL_1,
+		pll_code.k_code << RT1308_PLL1_K_SFT |
+		pll_code.m_bp << RT1308_PLL1_M_BYPASS_SFT |
+		(pll_code.m_bp ? 0 : pll_code.m_code) << RT1308_PLL1_M_SFT |
+		pll_code.n_code << RT1308_PLL1_N_SFT);
+
+	rt1308->pll_in = freq_in;
+	rt1308->pll_out = freq_out;
+	rt1308->pll_src = source;
+
+	return 0;
+}
+
+static int rt1308_probe(struct snd_soc_component *component)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+
+	rt1308->component = component;
+
+	/* initial settings */
+	rt1308_reg_init(component);
+
+	return 0;
+}
+
+static void rt1308_remove(struct snd_soc_component *component)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+
+	rt1308_reset(rt1308->regmap);
+}
+
+#ifdef CONFIG_PM
+static int rt1308_suspend(struct snd_soc_component *component)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+
+	regcache_cache_only(rt1308->regmap, true);
+	regcache_mark_dirty(rt1308->regmap);
+
+	return 0;
+}
+
+static int rt1308_resume(struct snd_soc_component *component)
+{
+	struct rt1308_priv *rt1308 = snd_soc_component_get_drvdata(component);
+
+	regcache_cache_only(rt1308->regmap, false);
+	regcache_sync(rt1308->regmap);
+
+	return 0;
+}
+#else
+#define rt1308_suspend NULL
+#define rt1308_resume NULL
+#endif
+
+#define RT1308_STEREO_RATES SNDRV_PCM_RATE_48000
+#define RT1308_FORMATS (SNDRV_PCM_FMTBIT_S8 | \
+			SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S16_LE | \
+			SNDRV_PCM_FMTBIT_S24_LE)
+
+static const struct snd_soc_dai_ops rt1308_aif_dai_ops = {
+	.hw_params = rt1308_hw_params,
+	.set_fmt = rt1308_set_dai_fmt,
+};
+
+static struct snd_soc_dai_driver rt1308_dai[] = {
+	{
+		.name = "rt1308-aif",
+		.playback = {
+			.stream_name = "AIF1 Playback",
+			.channels_min = 1,
+			.channels_max = 2,
+			.rates = RT1308_STEREO_RATES,
+			.formats = RT1308_FORMATS,
+		},
+		.ops = &rt1308_aif_dai_ops,
+	},
+};
+
+static const struct snd_soc_component_driver soc_component_dev_rt1308 = {
+	.probe = rt1308_probe,
+	.remove = rt1308_remove,
+	.suspend = rt1308_suspend,
+	.resume = rt1308_resume,
+	.controls = rt1308_snd_controls,
+	.num_controls = ARRAY_SIZE(rt1308_snd_controls),
+	.dapm_widgets = rt1308_dapm_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(rt1308_dapm_widgets),
+	.dapm_routes = rt1308_dapm_routes,
+	.num_dapm_routes = ARRAY_SIZE(rt1308_dapm_routes),
+	.set_sysclk = rt1308_set_component_sysclk,
+	.set_pll = rt1308_set_component_pll,
+	.use_pmdown_time	= 1,
+	.endianness		= 1,
+	.non_legacy_dai_naming	= 1,
+};
+
+static const struct regmap_config rt1308_regmap = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.max_register = RT1308_MAX_REG,
+	.volatile_reg = rt1308_volatile_register,
+	.readable_reg = rt1308_readable_register,
+	.cache_type = REGCACHE_RBTREE,
+	.reg_defaults = rt1308_reg,
+	.num_reg_defaults = ARRAY_SIZE(rt1308_reg),
+	.use_single_read = true,
+	.use_single_write = true,
+};
+
+#if defined(CONFIG_OF)
+static const struct of_device_id rt1308_of_match[] = {
+	{ .compatible = "realtek,rt1308", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rt1308_of_match);
+#endif
+
+#ifdef CONFIG_ACPI
+static struct acpi_device_id rt1308_acpi_match[] = {
+	{"10EC1308", 0,},
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, rt1308_acpi_match);
+#endif
+
+static const struct i2c_device_id rt1308_i2c_id[] = {
+	{ "rt1308", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, rt1308_i2c_id);
+
+static void rt1308_efuse(struct rt1308_priv *rt1308)
+{
+
+	rt1308_reset(rt1308->regmap);
+	regmap_write(rt1308->regmap, RT1308_POWER, 0xff371600);
+	regmap_write(rt1308->regmap, RT1308_CLK_1, 0x52100000);
+	regmap_write(rt1308->regmap, RT1308_I2C_I2S_SDW_SET, 0x01014005);
+	regmap_write(rt1308->regmap, RT1308_CLASS_D_SET_2, 0x227f5501);
+	regmap_write(rt1308->regmap, RT1308_PADS_1, 0x50150505);
+	regmap_write(rt1308->regmap, RT1308_VREF, 0x18100000);
+	regmap_write(rt1308->regmap, RT1308_IV_SENSE, 0x87010000);
+	regmap_write(rt1308->regmap, RT1308_DUMMY_REG, 0x00000200);
+	regmap_write(rt1308->regmap, RT1308_SIL_DET, 0x61c30000);
+	regmap_write(rt1308->regmap, RT1308_CLK_DET, 0x03700000);
+	regmap_write(rt1308->regmap, RT1308_SINE_TONE_GEN_1, 0x50022f00);
+	regmap_write(rt1308->regmap, RT1308_POWER_STATUS, 0x01800000);
+	regmap_write(rt1308->regmap, RT1308_DC_CAL_2, 0x00ffff00);
+	regmap_write(rt1308->regmap, RT1308_CLASS_D_SET_2, 0x607e5501);
+
+	/* EFUSE read */
+	regmap_write(rt1308->regmap, RT1308_CLK_2, 0x0060e000);
+	regmap_write(rt1308->regmap, RT1308_EFUSE_1, 0x04fe0f00);
+	msleep(100);
+	regmap_write(rt1308->regmap, RT1308_EFUSE_1, 0x44fe0f00);
+	msleep(20);
+	regmap_write(rt1308->regmap, RT1308_PVDD_OFFSET_CTL, 0x10000000);
+
+	/* restore some registers */
+	regmap_write(rt1308->regmap, RT1308_SINE_TONE_GEN_1, 0x10022f00);
+	regmap_write(rt1308->regmap, RT1308_POWER_STATUS, 0x00800000);
+	regmap_write(rt1308->regmap, RT1308_POWER, 0x0);
+
+}
+
+static int rt1308_i2c_probe(struct i2c_client *i2c,
+		    const struct i2c_device_id *id)
+{
+	struct rt1308_priv *rt1308;
+	int ret;
+	unsigned int val;
+
+	rt1308 = devm_kzalloc(&i2c->dev, sizeof(struct rt1308_priv),
+				GFP_KERNEL);
+	if (rt1308 == NULL)
+		return -ENOMEM;
+
+	i2c_set_clientdata(i2c, rt1308);
+
+	rt1308->regmap = devm_regmap_init_i2c(i2c, &rt1308_regmap);
+	if (IS_ERR(rt1308->regmap)) {
+		ret = PTR_ERR(rt1308->regmap);
+		dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	regmap_read(rt1308->regmap, RT1308_VEN_DEV_ID, &val);
+	/* ignore last byte difference */
+	if ((val & 0xFFFFFF00) != RT1308_DEVICE_ID_NUM) {
+		dev_err(&i2c->dev,
+			"Device with ID register %x is not rt1308\n", val);
+		return -ENODEV;
+	}
+
+	rt1308_reset(rt1308->regmap);
+	rt1308_efuse(rt1308);
+
+	return snd_soc_register_component(&i2c->dev, &soc_component_dev_rt1308,
+			rt1308_dai, ARRAY_SIZE(rt1308_dai));
+}
+
+static int rt1308_i2c_remove(struct i2c_client *i2c)
+{
+	snd_soc_unregister_component(&i2c->dev);
+
+	return 0;
+}
+
+static void rt1308_i2c_shutdown(struct i2c_client *client)
+{
+	struct rt1308_priv *rt1308 = i2c_get_clientdata(client);
+
+	rt1308_reset(rt1308->regmap);
+}
+
+
+static struct i2c_driver rt1308_i2c_driver = {
+	.driver = {
+		.name = "rt1308",
+		.owner = THIS_MODULE,
+#if defined(CONFIG_OF)
+		.of_match_table = rt1308_of_match,
+#endif
+#if defined(CONFIG_ACPI)
+		.acpi_match_table = ACPI_PTR(rt1308_acpi_match)
+#endif
+	},
+	.probe = rt1308_i2c_probe,
+	.remove   = rt1308_i2c_remove,
+	.shutdown = rt1308_i2c_shutdown,
+	.id_table = rt1308_i2c_id,
+};
+module_i2c_driver(rt1308_i2c_driver);
+
+MODULE_DESCRIPTION("ASoC RT1308 amplifier driver");
+MODULE_AUTHOR("Derek Fang <derek.fang@realtek.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/rt1308.h b/sound/soc/codecs/rt1308.h
new file mode 100755
index 000000000000..c330aae1d527
--- /dev/null
+++ b/sound/soc/codecs/rt1308.h
@@ -0,0 +1,291 @@ 
+/*
+ * RT1308.h  --  RT1308 ALSA SoC amplifier component driver
+ *
+ * Copyright 2019 Realtek Semiconductor Corp.
+ * Author: Derek Fang <derek.fang@realtek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _RT1308_H_
+#define _RT1308_H_
+
+#define RT1308_DEVICE_ID_NUM			0x10ec1300
+
+#define RT1308_RESET				0x00
+#define RT1308_RESET_N				0x01
+#define RT1308_CLK_GATING			0x02
+#define RT1308_PLL_1				0x03
+#define RT1308_PLL_2				0x04
+#define RT1308_PLL_INT				0x05
+#define RT1308_CLK_1				0x06
+#define RT1308_DATA_PATH			0x07
+#define RT1308_CLK_2				0x08
+#define RT1308_SIL_DET				0x09
+#define RT1308_CLK_DET				0x0a
+#define RT1308_DC_DET				0x0b
+#define RT1308_DC_DET_THRES			0x0c
+#define RT1308_DAC_SET				0x10
+#define RT1308_SRC_SET				0x11
+#define RT1308_DAC_BUF				0x12
+#define RT1308_ADC_SET				0x13
+#define RT1308_ADC_SET_INT			0x14
+#define RT1308_I2S_SET_1			0x15
+#define RT1308_I2S_SET_2			0x16
+#define RT1308_I2C_I2S_SDW_SET			0x17
+#define RT1308_SDW_REG_RW			0x18
+#define RT1308_SDW_REG_RDATA			0x19
+#define RT1308_IV_SENSE				0x1a
+#define RT1308_I2S_TX_DAC_SET			0x1b
+#define RT1308_AD_FILTER_SET			0x1c
+#define RT1308_DC_CAL_1				0x20
+#define RT1308_DC_CAL_2				0x21
+#define RT1308_DC_CAL_L_OFFSET			0x22
+#define RT1308_DC_CAL_R_OFFSET			0x23
+#define RT1308_PVDD_OFFSET_CTL			0x24
+#define RT1308_PVDD_OFFSET_L			0x25
+#define RT1308_PVDD_OFFSET_R			0x26
+#define RT1308_PVDD_OFFSET_PBTL			0x27
+#define RT1308_PVDD_OFFSET_PVDD			0x28
+#define RT1308_CAL_OFFSET_DAC_PBTL		0x29
+#define RT1308_CAL_OFFSET_DAC_L			0x2a
+#define RT1308_CAL_OFFSET_DAC_R			0x2b
+#define RT1308_CAL_OFFSET_PWM_L			0x2c
+#define RT1308_CAL_OFFSET_PWM_R			0x2d
+#define RT1308_CAL_PWM_VOS_ADC_L		0x2e
+#define RT1308_CAL_PWM_VOS_ADC_R		0x2f
+#define RT1308_CLASS_D_SET_1			0x30
+#define RT1308_CLASS_D_SET_2			0x31
+#define RT1308_POWER				0x32
+#define RT1308_LDO				0x33
+#define RT1308_VREF				0x34
+#define RT1308_MBIAS				0x35
+#define RT1308_POWER_STATUS			0x36
+#define RT1308_POWER_INT			0x37
+#define RT1308_SINE_TONE_GEN_1			0x50
+#define RT1308_SINE_TONE_GEN_2			0x51
+#define RT1308_BQ_SET				0x54
+#define RT1308_BQ_PARA_UPDATE			0x55
+#define RT1308_BQ_PRE_VOL_L			0x56
+#define RT1308_BQ_PRE_VOL_R			0x57
+#define RT1308_BQ_POST_VOL_L			0x58
+#define RT1308_BQ_POST_VOL_R			0x59
+#define RT1308_BQ1_L_H0				0x5b
+#define RT1308_BQ1_L_B1				0x5c
+#define RT1308_BQ1_L_B2				0x5d
+#define RT1308_BQ1_L_A1				0x5e
+#define RT1308_BQ1_L_A2				0x5f
+#define RT1308_BQ1_R_H0				0x60
+#define RT1308_BQ1_R_B1				0x61
+#define RT1308_BQ1_R_B2				0x62
+#define RT1308_BQ1_R_A1				0x63
+#define RT1308_BQ1_R_A2				0x64
+#define RT1308_BQ2_L_H0				0x65
+#define RT1308_BQ2_L_B1				0x66
+#define RT1308_BQ2_L_B2				0x67
+#define RT1308_BQ2_L_A1				0x68
+#define RT1308_BQ2_L_A2				0x69
+#define RT1308_BQ2_R_H0				0x6a
+#define RT1308_BQ2_R_B1				0x6b
+#define RT1308_BQ2_R_B2				0x6c
+#define RT1308_BQ2_R_A1				0x6d
+#define RT1308_BQ2_R_A2				0x6e
+#define RT1308_VEN_DEV_ID			0x70
+#define RT1308_VERSION_ID			0x71
+#define RT1308_SPK_BOUND			0x72
+#define RT1308_BQ1_EQ_L_1			0x73
+#define RT1308_BQ1_EQ_L_2			0x74
+#define RT1308_BQ1_EQ_L_3			0x75
+#define RT1308_BQ1_EQ_R_1			0x76
+#define RT1308_BQ1_EQ_R_2			0x77
+#define RT1308_BQ1_EQ_R_3			0x78
+#define RT1308_BQ2_EQ_L_1			0x79
+#define RT1308_BQ2_EQ_L_2			0x7a
+#define RT1308_BQ2_EQ_L_3			0x7b
+#define RT1308_BQ2_EQ_R_1			0x7c
+#define RT1308_BQ2_EQ_R_2			0x7d
+#define RT1308_BQ2_EQ_R_3			0x7e
+#define RT1308_EFUSE_1				0x7f
+#define RT1308_EFUSE_2				0x80
+#define RT1308_EFUSE_PROG_PVDD_L		0x81
+#define RT1308_EFUSE_PROG_PVDD_R		0x82
+#define RT1308_EFUSE_PROG_R0_L			0x83
+#define RT1308_EFUSE_PROG_R0_R			0x84
+#define RT1308_EFUSE_PROG_DEV			0x85
+#define RT1308_EFUSE_READ_PVDD_L		0x86
+#define RT1308_EFUSE_READ_PVDD_R		0x87
+#define RT1308_EFUSE_READ_PVDD_PTBL		0x88
+#define RT1308_EFUSE_READ_DEV			0x89
+#define RT1308_EFUSE_READ_R0			0x8a
+#define RT1308_EFUSE_READ_ADC_L			0x8b
+#define RT1308_EFUSE_READ_ADC_R			0x8c
+#define RT1308_EFUSE_READ_ADC_PBTL		0x8d
+#define RT1308_EFUSE_RESERVE			0x8e
+#define RT1308_PADS_1				0x90
+#define RT1308_PADS_2				0x91
+#define RT1308_TEST_MODE			0xa0
+#define RT1308_TEST_1				0xa1
+#define RT1308_TEST_2				0xa2
+#define RT1308_TEST_3				0xa3
+#define RT1308_TEST_4				0xa4
+#define RT1308_EFUSE_DATA_0_MSB			0xb0
+#define RT1308_EFUSE_DATA_0_LSB			0xb1
+#define RT1308_EFUSE_DATA_1_MSB			0xb2
+#define RT1308_EFUSE_DATA_1_LSB			0xb3
+#define RT1308_EFUSE_DATA_2_MSB			0xb4
+#define RT1308_EFUSE_DATA_2_LSB			0xb5
+#define RT1308_EFUSE_DATA_3_MSB			0xb6
+#define RT1308_EFUSE_DATA_3_LSB			0xb7
+#define RT1308_EFUSE_DATA_TEST_MSB		0xb8
+#define RT1308_EFUSE_DATA_TEST_LSB		0xb9
+#define RT1308_EFUSE_STATUS_1			0xba
+#define RT1308_EFUSE_STATUS_2			0xbb
+#define RT1308_TCON_1				0xc0
+#define RT1308_TCON_2				0xc1
+#define RT1308_DUMMY_REG			0xf0
+#define RT1308_MAX_REG				0xff
+
+/* PLL1 M/N/K Code-1 (0x03) */
+#define RT1308_PLL1_K_SFT			24
+#define RT1308_PLL1_K_MASK			(0x1f << 24)
+#define RT1308_PLL1_M_BYPASS_MASK		(0x1 << 23)
+#define RT1308_PLL1_M_BYPASS_SFT		23
+#define RT1308_PLL1_M_BYPASS			(0x1 << 23)
+#define RT1308_PLL1_M_MASK			(0x3f << 16)
+#define RT1308_PLL1_M_SFT			16
+#define RT1308_PLL1_N_MASK			(0x7f << 8)
+#define RT1308_PLL1_N_SFT			8
+
+/* CLOCK-1 (0x06) */
+#define RT1308_DIV_FS_SYS_MASK			(0xf << 28)
+#define RT1308_DIV_FS_SYS_SFT			28
+#define RT1308_SEL_FS_SYS_MASK			(0x7 << 24)
+#define RT1308_SEL_FS_SYS_SFT			24
+#define RT1308_SEL_FS_SYS_SRC_MCLK		(0x0 << 24)
+#define RT1308_SEL_FS_SYS_SRC_BCLK		(0x1 << 24)
+#define RT1308_SEL_FS_SYS_SRC_PLL		(0x2 << 24)
+#define RT1308_SEL_FS_SYS_SRC_RCCLK		(0x4 << 24)
+
+/* CLOCK-2 (0x08) */
+#define RT1308_DIV_PRE_PLL_MASK			(0xf << 28)
+#define RT1308_DIV_PRE_PLL_SFT			28
+#define RT1308_SEL_PLL_SRC_MASK			(0x7 << 24)
+#define RT1308_SEL_PLL_SRC_SFT			24
+#define RT1308_SEL_PLL_SRC_MCLK			(0x0 << 24)
+#define RT1308_SEL_PLL_SRC_BCLK			(0x1 << 24)
+#define RT1308_SEL_PLL_SRC_RCCLK		(0x4 << 24)
+
+/* Clock Detect (0x0a) */
+#define RT1308_MCLK_DET_EN_MASK			(0x1 << 25)
+#define RT1308_MCLK_DET_EN_SFT			25
+#define RT1308_MCLK_DET_EN			(0x1 << 25)
+#define RT1308_BCLK_DET_EN_MASK			(0x1 << 24)
+#define RT1308_BCLK_DET_EN_SFT			24
+#define RT1308_BCLK_DET_EN			(0x1 << 24)
+
+/* DAC Setting (0x10) */
+#define RT1308_DVOL_MUTE_R_EN_SFT		7
+#define RT1308_DVOL_MUTE_L_EN_SFT		6
+
+/* I2S Setting-1 (0x15) */
+#define RT1308_I2S_DF_SEL_MASK			(0x3 << 12)
+#define RT1308_I2S_DF_SEL_SFT			12
+#define RT1308_I2S_DF_SEL_I2S			(0x0 << 12)
+#define RT1308_I2S_DF_SEL_LEFT			(0x1 << 12)
+#define RT1308_I2S_DF_SEL_PCM_A			(0x2 << 12)
+#define RT1308_I2S_DF_SEL_PCM_B			(0x3 << 12)
+#define RT1308_I2S_DL_RX_SEL_MASK		(0x7 << 4)
+#define RT1308_I2S_DL_RX_SEL_SFT		4
+#define RT1308_I2S_DL_RX_SEL_16B		(0x0 << 4)
+#define RT1308_I2S_DL_RX_SEL_20B		(0x1 << 4)
+#define RT1308_I2S_DL_RX_SEL_24B		(0x2 << 4)
+#define RT1308_I2S_DL_RX_SEL_32B		(0x3 << 4)
+#define RT1308_I2S_DL_RX_SEL_8B			(0x4 << 4)
+#define RT1308_I2S_DL_TX_SEL_MASK		(0x7 << 0)
+#define RT1308_I2S_DL_TX_SEL_SFT		0
+#define RT1308_I2S_DL_TX_SEL_16B		(0x0 << 0)
+#define RT1308_I2S_DL_TX_SEL_20B		(0x1 << 0)
+#define RT1308_I2S_DL_TX_SEL_24B		(0x2 << 0)
+#define RT1308_I2S_DL_TX_SEL_32B		(0x3 << 0)
+#define RT1308_I2S_DL_TX_SEL_8B			(0x4 << 0)
+
+/* I2S Setting-2 (0x16) */
+#define RT1308_I2S_DL_SEL_MASK			(0x7 << 24)
+#define RT1308_I2S_DL_SEL_SFT			24
+#define RT1308_I2S_DL_SEL_16B			(0x0 << 24)
+#define RT1308_I2S_DL_SEL_20B			(0x1 << 24)
+#define RT1308_I2S_DL_SEL_24B			(0x2 << 24)
+#define RT1308_I2S_DL_SEL_32B			(0x3 << 24)
+#define RT1308_I2S_DL_SEL_8B			(0x4 << 24)
+#define RT1308_I2S_BCLK_MASK			(0x1 << 14)
+#define RT1308_I2S_BCLK_SFT			14
+#define RT1308_I2S_BCLK_NORMAL			(0x0 << 14)
+#define RT1308_I2S_BCLK_INV			(0x1 << 14)
+
+/* Power Control-1 (0x32) */
+#define RT1308_POW_MBIAS20U			(0x1 << 31)
+#define RT1308_POW_MBIAS20U_BIT			31
+#define RT1308_POW_ALDO				(0x1 << 30)
+#define RT1308_POW_ALDO_BIT			30
+#define RT1308_POW_DBG				(0x1 << 29)
+#define RT1308_POW_DBG_BIT			29
+#define RT1308_POW_DACL				(0x1 << 28)
+#define RT1308_POW_DACL_BIT			28
+#define RT1308_POW_DAC1				(0x1 << 27)
+#define RT1308_POW_DAC1_BIT			27
+#define RT1308_POW_CLK25M			(0x1 << 26)
+#define RT1308_POW_CLK25M_BIT			26
+#define RT1308_POW_ADC_R			(0x1 << 25)
+#define RT1308_POW_ADC_R_BIT			25
+#define RT1308_POW_ADC_L			(0x1 << 24)
+#define RT1308_POW_ADC_L_BIT			24
+#define RT1308_POW_DLDO				(0x1 << 21)
+#define RT1308_POW_DLDO_BIT			21
+#define RT1308_POW_VREF				(0x1 << 20)
+#define RT1308_POW_VREF_BIT			20
+#define RT1308_POW_MIXER_R			(0x1 << 18)
+#define RT1308_POW_MIXER_R_BIT			18
+#define RT1308_POW_MIXER_L			(0x1 << 17)
+#define RT1308_POW_MIXER_L_BIT			17
+#define RT1308_POW_MBIAS4U			(0x1 << 16)
+#define RT1308_POW_MBIAS4U_BIT			16
+#define RT1308_POW_PLL2_LDO_EN			(0x1 << 12)
+#define RT1308_POW_PLL2_LDO_EN_BIT		12
+#define RT1308_POW_PLL2B_EN			(0x1 << 11)
+#define RT1308_POW_PLL2B_EN_BIT			11
+#define RT1308_POW_PLL2F_EN			(0x1 << 10)
+#define RT1308_POW_PLL2F_EN_BIT			10
+#define RT1308_POW_PLL2F2_EN			(0x1 << 9)
+#define RT1308_POW_PLL2F2_EN_BIT		9
+#define RT1308_POW_PLL2B2_EN			(0x1 << 8)
+#define RT1308_POW_PLL2B2_EN_BIT		8
+
+/* Power Control-2 (0x36) */
+#define RT1308_POW_PDB_SRC_BIT			(0x1 << 27)
+#define RT1308_POW_PDB_MN_BIT			(0x1 << 25)
+#define RT1308_POW_PDB_REG_BIT			(0x1 << 24)
+
+
+/* System Clock Source */
+enum {
+	RT1308_FS_SYS_S_MCLK,
+	RT1308_FS_SYS_S_BCLK,
+	RT1308_FS_SYS_S_PLL,
+	RT1308_FS_SYS_S_RCCLK,	/* 25.0 MHz */
+};
+
+/* PLL Source */
+enum {
+	RT1308_PLL_S_MCLK,
+	RT1308_PLL_S_BCLK,
+	RT1308_PLL_S_RCCLK,
+};
+
+enum {
+	RT1308_AIF1,
+	RT1308_AIFS
+};
+
+#endif		/* end of _RT1308_H_ */