Message ID | 1566998177-2658-2-git-send-email-wgong@codeaurora.org (mailing list archive) |
---|---|
State | Changes Requested |
Delegated to: | Kalle Valo |
Headers | show |
Series | ath10k: improve throughout of tcp/udp TX/RX of sdio | expand |
On Thu, Aug 29, 2019 at 12:18 AM Wen Gong <wgong@codeaurora.org> wrote: > > When the FW bundles multiple packets, pkt->act_len may be incorrect > as it refers to the first packet only (however, the FW will only > bundle packets that fit into the same pkt->alloc_len). > > Before this patch, the skb length would be set (incorrectly) to > pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually > adjusted in ath10k_sdio_mbox_rx_process_packet. > > The first problem is that ath10k_sdio_mbox_rx_process_packet does not > use proper skb_put commands to adjust the length (it directly changes > skb->len), so we end up with a mismatch between skb->head + skb->tail > and skb->data + skb->len. This is quite serious, and causes corruptions > in the TCP stack, as the stack tries to coalesce packets, and relies > on skb->tail being correct (that is, skb_tail_pointer must point to > the first byte_after_ the data). > > Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet, > this moves the code to ath10k_sdio_mbox_rx_packet, and also add a > bounds check, as skb_put would crash the kernel if not enough space is > available. > > Tested with QCA6174 SDIO with firmware > WLAN.RMH.4.4.1-00007-QCARMSWP-1. > > Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> > Signed-off-by: Wen Gong <wgong@codeaurora.org> You are not the author of this patch, please reset the author in your git tree and resend. Once you do that, the first line should say: From: Nicolas Boichat <drinkcat@chromium.org> Without this fix: NACKed-by: Nicolas Boichat <drinkcat@chromium.org> > --- > v2:no this patch > v2:new added > drivers/net/wireless/ath/ath10k/sdio.c | 27 +++++++++++++++++++-------- > 1 file changed, 19 insertions(+), 8 deletions(-) > > diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c > index 8ed4fbd..1127e44 100644 > --- a/drivers/net/wireless/ath/ath10k/sdio.c > +++ b/drivers/net/wireless/ath/ath10k/sdio.c > @@ -381,16 +381,11 @@ static int ath10k_sdio_mbox_rx_process_packet(struct ath10k *ar, > struct ath10k_htc_hdr *htc_hdr = (struct ath10k_htc_hdr *)skb->data; > bool trailer_present = htc_hdr->flags & ATH10K_HTC_FLAG_TRAILER_PRESENT; > enum ath10k_htc_ep_id eid; > - u16 payload_len; > u8 *trailer; > int ret; > > - payload_len = le16_to_cpu(htc_hdr->len); > - skb->len = payload_len + sizeof(struct ath10k_htc_hdr); > - > if (trailer_present) { > - trailer = skb->data + sizeof(*htc_hdr) + > - payload_len - htc_hdr->trailer_len; > + trailer = skb->data + skb->len - htc_hdr->trailer_len; > > eid = pipe_id_to_eid(htc_hdr->eid); > > @@ -632,13 +627,29 @@ static int ath10k_sdio_mbox_rx_packet(struct ath10k *ar, > { > struct ath10k_sdio *ar_sdio = ath10k_sdio_priv(ar); > struct sk_buff *skb = pkt->skb; > + struct ath10k_htc_hdr *htc_hdr; > int ret; > > ret = ath10k_sdio_readsb(ar, ar_sdio->mbox_info.htc_addr, > skb->data, pkt->alloc_len); > + > + if (!ret) { > + /* Update actual length. The original length may be incorrect, > + * as the FW will bundle multiple packets as long as their sizes > + * fit within the same aligned length (pkt->alloc_len). > + */ > + htc_hdr = (struct ath10k_htc_hdr *)skb->data; > + pkt->act_len = le16_to_cpu(htc_hdr->len) + sizeof(*htc_hdr); > + if (pkt->act_len <= pkt->alloc_len) { > + skb_put(skb, pkt->act_len); > + } else { > + ath10k_warn(ar, "rx packet too large (%zu > %zu)\n", > + pkt->act_len, pkt->alloc_len); > + ret = -EMSGSIZE; > + } > + } > + > pkt->status = ret; > - if (!ret) > - skb_put(skb, pkt->act_len); > > return ret; > } > -- > 1.9.1 >
On Fri, Aug 30, 2019 at 10:53 AM Nicolas Boichat <drinkcat@chromium.org> wrote: > > On Thu, Aug 29, 2019 at 12:18 AM Wen Gong <wgong@codeaurora.org> wrote: > > > > When the FW bundles multiple packets, pkt->act_len may be incorrect > > as it refers to the first packet only (however, the FW will only > > bundle packets that fit into the same pkt->alloc_len). > > > > Before this patch, the skb length would be set (incorrectly) to > > pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually > > adjusted in ath10k_sdio_mbox_rx_process_packet. > > > > The first problem is that ath10k_sdio_mbox_rx_process_packet does not > > use proper skb_put commands to adjust the length (it directly changes > > skb->len), so we end up with a mismatch between skb->head + skb->tail > > and skb->data + skb->len. This is quite serious, and causes corruptions > > in the TCP stack, as the stack tries to coalesce packets, and relies > > on skb->tail being correct (that is, skb_tail_pointer must point to > > the first byte_after_ the data). > > > > Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet, > > this moves the code to ath10k_sdio_mbox_rx_packet, and also add a > > bounds check, as skb_put would crash the kernel if not enough space is > > available. > > > > Tested with QCA6174 SDIO with firmware > > WLAN.RMH.4.4.1-00007-QCARMSWP-1. > > > > Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> > > Signed-off-by: Wen Gong <wgong@codeaurora.org> > > You are not the author of this patch, please reset the author in your > git tree and resend. > > Once you do that, the first line should say: > From: Nicolas Boichat <drinkcat@chromium.org> > > Without this fix: > NACKed-by: Nicolas Boichat <drinkcat@chromium.org> > Also you dropped the Fixes line: Fixes: 8530b4e7b22bc3b ("ath10k: sdio: set skb len for all rx packets") > > --- > > v2:no this patch > > v2:new added > > drivers/net/wireless/ath/ath10k/sdio.c | 27 +++++++++++++++++++-------- > > 1 file changed, 19 insertions(+), 8 deletions(-) > > > > diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c > > index 8ed4fbd..1127e44 100644 > > --- a/drivers/net/wireless/ath/ath10k/sdio.c > > +++ b/drivers/net/wireless/ath/ath10k/sdio.c > > @@ -381,16 +381,11 @@ static int ath10k_sdio_mbox_rx_process_packet(struct ath10k *ar, > > struct ath10k_htc_hdr *htc_hdr = (struct ath10k_htc_hdr *)skb->data; > > bool trailer_present = htc_hdr->flags & ATH10K_HTC_FLAG_TRAILER_PRESENT; > > enum ath10k_htc_ep_id eid; > > - u16 payload_len; > > u8 *trailer; > > int ret; > > > > - payload_len = le16_to_cpu(htc_hdr->len); > > - skb->len = payload_len + sizeof(struct ath10k_htc_hdr); > > - > > if (trailer_present) { > > - trailer = skb->data + sizeof(*htc_hdr) + > > - payload_len - htc_hdr->trailer_len; > > + trailer = skb->data + skb->len - htc_hdr->trailer_len; > > > > eid = pipe_id_to_eid(htc_hdr->eid); > > > > @@ -632,13 +627,29 @@ static int ath10k_sdio_mbox_rx_packet(struct ath10k *ar, > > { > > struct ath10k_sdio *ar_sdio = ath10k_sdio_priv(ar); > > struct sk_buff *skb = pkt->skb; > > + struct ath10k_htc_hdr *htc_hdr; > > int ret; > > > > ret = ath10k_sdio_readsb(ar, ar_sdio->mbox_info.htc_addr, > > skb->data, pkt->alloc_len); > > + > > + if (!ret) { > > + /* Update actual length. The original length may be incorrect, > > + * as the FW will bundle multiple packets as long as their sizes > > + * fit within the same aligned length (pkt->alloc_len). > > + */ > > + htc_hdr = (struct ath10k_htc_hdr *)skb->data; > > + pkt->act_len = le16_to_cpu(htc_hdr->len) + sizeof(*htc_hdr); > > + if (pkt->act_len <= pkt->alloc_len) { > > + skb_put(skb, pkt->act_len); > > + } else { > > + ath10k_warn(ar, "rx packet too large (%zu > %zu)\n", > > + pkt->act_len, pkt->alloc_len); > > + ret = -EMSGSIZE; > > + } > > + } > > + > > pkt->status = ret; > > - if (!ret) > > - skb_put(skb, pkt->act_len); > > > > return ret; > > } > > -- > > 1.9.1 > >
> -----Original Message----- > From: ath10k <ath10k-bounces@lists.infradead.org> On Behalf Of Wen Gong > Sent: Wednesday, August 28, 2019 9:16 PM > To: ath10k@lists.infradead.org > Cc: linux-wireless@vger.kernel.org > Subject: [EXT] [PATCH v3 1/8] ath10k: adjust skb length in > ath10k_sdio_mbox_rx_packet > Patch v4 sent, https://patchwork.kernel.org/patch/11126221/ > > > _______________________________________________ > ath10k mailing list > ath10k@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/ath10k
diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c index 8ed4fbd..1127e44 100644 --- a/drivers/net/wireless/ath/ath10k/sdio.c +++ b/drivers/net/wireless/ath/ath10k/sdio.c @@ -381,16 +381,11 @@ static int ath10k_sdio_mbox_rx_process_packet(struct ath10k *ar, struct ath10k_htc_hdr *htc_hdr = (struct ath10k_htc_hdr *)skb->data; bool trailer_present = htc_hdr->flags & ATH10K_HTC_FLAG_TRAILER_PRESENT; enum ath10k_htc_ep_id eid; - u16 payload_len; u8 *trailer; int ret; - payload_len = le16_to_cpu(htc_hdr->len); - skb->len = payload_len + sizeof(struct ath10k_htc_hdr); - if (trailer_present) { - trailer = skb->data + sizeof(*htc_hdr) + - payload_len - htc_hdr->trailer_len; + trailer = skb->data + skb->len - htc_hdr->trailer_len; eid = pipe_id_to_eid(htc_hdr->eid); @@ -632,13 +627,29 @@ static int ath10k_sdio_mbox_rx_packet(struct ath10k *ar, { struct ath10k_sdio *ar_sdio = ath10k_sdio_priv(ar); struct sk_buff *skb = pkt->skb; + struct ath10k_htc_hdr *htc_hdr; int ret; ret = ath10k_sdio_readsb(ar, ar_sdio->mbox_info.htc_addr, skb->data, pkt->alloc_len); + + if (!ret) { + /* Update actual length. The original length may be incorrect, + * as the FW will bundle multiple packets as long as their sizes + * fit within the same aligned length (pkt->alloc_len). + */ + htc_hdr = (struct ath10k_htc_hdr *)skb->data; + pkt->act_len = le16_to_cpu(htc_hdr->len) + sizeof(*htc_hdr); + if (pkt->act_len <= pkt->alloc_len) { + skb_put(skb, pkt->act_len); + } else { + ath10k_warn(ar, "rx packet too large (%zu > %zu)\n", + pkt->act_len, pkt->alloc_len); + ret = -EMSGSIZE; + } + } + pkt->status = ret; - if (!ret) - skb_put(skb, pkt->act_len); return ret; }