| Message ID | 20190814214319.24087-1-andreas@kemnade.info (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | [v2] regulator: twl: voltage lists for vdd1/2 on twl4030 | expand |
On Wed, Aug 14, 2019 at 5:18 PM Andreas Kemnade <andreas@kemnade.info> wrote: > > _opp_supported_by_regulators() wrongly ignored errors from > regulator_is_supported_voltage(), so it considered errors as > success. Since > commit 498209445124 ("regulator: core: simplify return value on suported_voltage") > regulator_is_supported_voltage() returns a real boolean, so > errors make _opp_supported_by_regulators() return false. > > That reveals a problem with the declaration of the VDD1/2 > regulators on twl4030. > The VDD1/VDD2 regulators on twl4030 are neither defined with > voltage lists nor with the continuous flag set, so > regulator_is_supported_voltage() returns false and an error > before above mentioned commit (which was considered success) > The result is that after the above mentioned commit cpufreq > does not work properly e.g. dm3730. > > [ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator > [ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000) > [ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator > [ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000) > [ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator > [ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000) > > The patch fixes declaration of VDD1/2 regulators by > adding proper voltage lists. > > Fixes: 498209445124 ("regulator: core: simplify return value on suported_voltage") > Cc: stable@vger.kernel.org > Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit > --- > resent because it was rejected by mailing lists, due to technical > issues, sorry for the noise. > changes in v2: > using a proper voltage list instead of misusing the continuous flag > subject was regulator: twl: mark vdd1/2 as continuous on twl4030 > > drivers/regulator/twl-regulator.c | 23 ++++++++++++++++++++--- > 1 file changed, 20 insertions(+), 3 deletions(-) > > diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c > index 6fa15b2d6fb3..866b4dd01da9 100644 > --- a/drivers/regulator/twl-regulator.c > +++ b/drivers/regulator/twl-regulator.c > @@ -359,6 +359,17 @@ static const u16 VINTANA2_VSEL_table[] = { > 2500, 2750, > }; > > +/* 600mV to 1450mV in 12.5 mV steps */ > +static const struct regulator_linear_range VDD1_ranges[] = { > + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500) > +}; > + > +/* 600mV to 1450mV in 12.5 mV steps, everything above = 1500mV */ > +static const struct regulator_linear_range VDD2_ranges[] = { > + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500), > + REGULATOR_LINEAR_RANGE(1500000, 69, 69, 12500) > +}; > + > static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) > { > struct twlreg_info *info = rdev_get_drvdata(rdev); > @@ -427,6 +438,8 @@ static int twl4030smps_get_voltage(struct regulator_dev *rdev) > } > > static const struct regulator_ops twl4030smps_ops = { > + .list_voltage = regulator_list_voltage_linear_range, > + > .set_voltage = twl4030smps_set_voltage, > .get_voltage = twl4030smps_get_voltage, > }; > @@ -466,7 +479,8 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ > }, \ > } > > -#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf) \ > +#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf, \ > + n_volt) \ > static const struct twlreg_info TWL4030_INFO_##label = { \ > .base = offset, \ > .id = num, \ > @@ -479,6 +493,9 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ > .owner = THIS_MODULE, \ > .enable_time = turnon_delay, \ > .of_map_mode = twl4030reg_map_mode, \ > + .n_voltages = n_volt, \ > + .n_linear_ranges = ARRAY_SIZE(label ## _ranges), \ > + .linear_ranges = label ## _ranges, \ > }, \ > } > > @@ -518,8 +535,8 @@ TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); > TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); > TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); > TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); > -TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08); > -TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08); > +TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08, 68); > +TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08, 69); > /* VUSBCP is managed *only* by the USB subchip */ > TWL4030_FIXED_LDO(VINTANA1, 0x3f, 1500, 11, 100, 0x08); > TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08); > -- > 2.20.1 >
On Thu, Aug 15, 2019 at 5:47 AM Adam Ford <aford173@gmail.com> wrote: > > On Wed, Aug 14, 2019 at 5:18 PM Andreas Kemnade <andreas@kemnade.info> wrote: > > > > _opp_supported_by_regulators() wrongly ignored errors from > > regulator_is_supported_voltage(), so it considered errors as > > success. Since > > commit 498209445124 ("regulator: core: simplify return value on suported_voltage") > > regulator_is_supported_voltage() returns a real boolean, so > > errors make _opp_supported_by_regulators() return false. > > > > That reveals a problem with the declaration of the VDD1/2 > > regulators on twl4030. > > The VDD1/VDD2 regulators on twl4030 are neither defined with > > voltage lists nor with the continuous flag set, so > > regulator_is_supported_voltage() returns false and an error > > before above mentioned commit (which was considered success) > > The result is that after the above mentioned commit cpufreq > > does not work properly e.g. dm3730. > > > > [ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator > > [ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000) > > [ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator > > [ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000) > > [ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator > > [ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000) > > > > The patch fixes declaration of VDD1/2 regulators by > > adding proper voltage lists. > > > > Fixes: 498209445124 ("regulator: core: simplify return value on suported_voltage") > > Cc: stable@vger.kernel.org > > Signed-off-by: Andreas Kemnade <andreas@kemnade.info> > > Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit > I am not sure who the right maintainer is, but as of today, cpufreq for users of twl4030 on 5.3-RC8 is still broken without this patch. Is there any way it can be applied before the final release? thank you, adam > > --- > > resent because it was rejected by mailing lists, due to technical > > issues, sorry for the noise. > > changes in v2: > > using a proper voltage list instead of misusing the continuous flag > > subject was regulator: twl: mark vdd1/2 as continuous on twl4030 > > > > drivers/regulator/twl-regulator.c | 23 ++++++++++++++++++++--- > > 1 file changed, 20 insertions(+), 3 deletions(-) > > > > diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c > > index 6fa15b2d6fb3..866b4dd01da9 100644 > > --- a/drivers/regulator/twl-regulator.c > > +++ b/drivers/regulator/twl-regulator.c > > @@ -359,6 +359,17 @@ static const u16 VINTANA2_VSEL_table[] = { > > 2500, 2750, > > }; > > > > +/* 600mV to 1450mV in 12.5 mV steps */ > > +static const struct regulator_linear_range VDD1_ranges[] = { > > + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500) > > +}; > > + > > +/* 600mV to 1450mV in 12.5 mV steps, everything above = 1500mV */ > > +static const struct regulator_linear_range VDD2_ranges[] = { > > + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500), > > + REGULATOR_LINEAR_RANGE(1500000, 69, 69, 12500) > > +}; > > + > > static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) > > { > > struct twlreg_info *info = rdev_get_drvdata(rdev); > > @@ -427,6 +438,8 @@ static int twl4030smps_get_voltage(struct regulator_dev *rdev) > > } > > > > static const struct regulator_ops twl4030smps_ops = { > > + .list_voltage = regulator_list_voltage_linear_range, > > + > > .set_voltage = twl4030smps_set_voltage, > > .get_voltage = twl4030smps_get_voltage, > > }; > > @@ -466,7 +479,8 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ > > }, \ > > } > > > > -#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf) \ > > +#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf, \ > > + n_volt) \ > > static const struct twlreg_info TWL4030_INFO_##label = { \ > > .base = offset, \ > > .id = num, \ > > @@ -479,6 +493,9 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ > > .owner = THIS_MODULE, \ > > .enable_time = turnon_delay, \ > > .of_map_mode = twl4030reg_map_mode, \ > > + .n_voltages = n_volt, \ > > + .n_linear_ranges = ARRAY_SIZE(label ## _ranges), \ > > + .linear_ranges = label ## _ranges, \ > > }, \ > > } > > > > @@ -518,8 +535,8 @@ TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); > > TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); > > TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); > > TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); > > -TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08); > > -TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08); > > +TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08, 68); > > +TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08, 69); > > /* VUSBCP is managed *only* by the USB subchip */ > > TWL4030_FIXED_LDO(VINTANA1, 0x3f, 1500, 11, 100, 0x08); > > TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08); > > -- > > 2.20.1 > >
On Mon, 9 Sep 2019 08:32:06 -0500 Adam Ford <aford173@gmail.com> wrote: > > > The patch fixes declaration of VDD1/2 regulators by > > > adding proper voltage lists. > > > > > > Fixes: 498209445124 ("regulator: core: simplify return value on suported_voltage") > > > Cc: stable@vger.kernel.org > > > Signed-off-by: Andreas Kemnade <andreas@kemnade.info> > > > > Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit > > > > I am not sure who the right maintainer is, but as of today, cpufreq > for users of twl4030 on 5.3-RC8 is still broken without this patch. > Is there any way it can be applied before the final release? > seems to have arrived in Mark Brown's regulator branches. and in linux-next/pending-fixes. But did not go further... Regards, Andreas
On Mon, Sep 09, 2019 at 08:32:06AM -0500, Adam Ford wrote: > I am not sure who the right maintainer is, but as of today, cpufreq > for users of twl4030 on 5.3-RC8 is still broken without this patch. > Is there any way it can be applied before the final release? Ugh, this affects cpufreq :/ I hadn't realized, sorry. At this point it's probably a bit late to get it into the release, but it is tagged for stable so if it doesn't make it in it will be in one of the first stable releases.
diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c index 6fa15b2d6fb3..866b4dd01da9 100644 --- a/drivers/regulator/twl-regulator.c +++ b/drivers/regulator/twl-regulator.c @@ -359,6 +359,17 @@ static const u16 VINTANA2_VSEL_table[] = { 2500, 2750, }; +/* 600mV to 1450mV in 12.5 mV steps */ +static const struct regulator_linear_range VDD1_ranges[] = { + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500) +}; + +/* 600mV to 1450mV in 12.5 mV steps, everything above = 1500mV */ +static const struct regulator_linear_range VDD2_ranges[] = { + REGULATOR_LINEAR_RANGE(600000, 0, 68, 12500), + REGULATOR_LINEAR_RANGE(1500000, 69, 69, 12500) +}; + static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) { struct twlreg_info *info = rdev_get_drvdata(rdev); @@ -427,6 +438,8 @@ static int twl4030smps_get_voltage(struct regulator_dev *rdev) } static const struct regulator_ops twl4030smps_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .set_voltage = twl4030smps_set_voltage, .get_voltage = twl4030smps_get_voltage, }; @@ -466,7 +479,8 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ }, \ } -#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf) \ +#define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf, \ + n_volt) \ static const struct twlreg_info TWL4030_INFO_##label = { \ .base = offset, \ .id = num, \ @@ -479,6 +493,9 @@ static const struct twlreg_info TWL4030_INFO_##label = { \ .owner = THIS_MODULE, \ .enable_time = turnon_delay, \ .of_map_mode = twl4030reg_map_mode, \ + .n_voltages = n_volt, \ + .n_linear_ranges = ARRAY_SIZE(label ## _ranges), \ + .linear_ranges = label ## _ranges, \ }, \ } @@ -518,8 +535,8 @@ TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); -TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08); -TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08); +TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08, 68); +TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08, 69); /* VUSBCP is managed *only* by the USB subchip */ TWL4030_FIXED_LDO(VINTANA1, 0x3f, 1500, 11, 100, 0x08); TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08);
_opp_supported_by_regulators() wrongly ignored errors from regulator_is_supported_voltage(), so it considered errors as success. Since commit 498209445124 ("regulator: core: simplify return value on suported_voltage") regulator_is_supported_voltage() returns a real boolean, so errors make _opp_supported_by_regulators() return false. That reveals a problem with the declaration of the VDD1/2 regulators on twl4030. The VDD1/VDD2 regulators on twl4030 are neither defined with voltage lists nor with the continuous flag set, so regulator_is_supported_voltage() returns false and an error before above mentioned commit (which was considered success) The result is that after the above mentioned commit cpufreq does not work properly e.g. dm3730. [ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator [ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000) [ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator [ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000) [ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator [ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000) The patch fixes declaration of VDD1/2 regulators by adding proper voltage lists. Fixes: 498209445124 ("regulator: core: simplify return value on suported_voltage") Cc: stable@vger.kernel.org Signed-off-by: Andreas Kemnade <andreas@kemnade.info> --- resent because it was rejected by mailing lists, due to technical issues, sorry for the noise. changes in v2: using a proper voltage list instead of misusing the continuous flag subject was regulator: twl: mark vdd1/2 as continuous on twl4030 drivers/regulator/twl-regulator.c | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)