| Message ID | 1588820612-15884-1-git-send-email-vnaralas@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [PATCHv4] ath10k : Fix channel survey dump | expand |
On 5/7/20 11:03 AM, Venkateswara Naralasetty wrote: > Channel active/busy time are showing incorrect(less than previous or > sometimes zero) for successive survey dump command. > > example: > Survey data from wlan0 > frequency: 5180 MHz [in use] > channel active time: 54995 ms > channel busy time: 432 ms > channel receive time: 0 ms > channel transmit time: 59 ms > Survey data from wlan0 > frequency: 5180 MHz [in use] > channel active time: 32592 ms > channel busy time: 254 ms > channel receive time: 0 ms > channel transmit time: 0 ms > > This patch fix this issue by assigning 'wmi_bss_survey_req_type' > as 'WMI_BSS_SURVEY_REQ_TYPE_READ' which accumulate survey data in > FW and send survey data to driver upon the driver request. Wrap around > is taken care by FW. > > hardware used : QCA9984 > firmware ver : ver 10.4-3.5.3-00057 > > hardware used : QCA988X > firmware ver : 10.2.4-1.0-00047 > > Tested-by: Markus Theil <markus.theil@tu-ilmenau.de> > Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> > --- > v4: > * updated signed-off-by > > v3: > * Rebased on TOT and added Tested-by > > drivers/net/wireless/ath/ath10k/mac.c | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c > index a1147cc..9330b52 100644 > --- a/drivers/net/wireless/ath/ath10k/mac.c > +++ b/drivers/net/wireless/ath/ath10k/mac.c > @@ -7275,7 +7275,7 @@ ath10k_mac_update_bss_chan_survey(struct ath10k *ar, > struct ieee80211_channel *channel) > { > int ret; > - enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR; > + enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ; > > lockdep_assert_held(&ar->conf_mutex); > > I have tested this on a QCA9980 device on a TP-Link Archer A7v5 with the firmware version 10.2.4.70.70. [root@Archer-A7v5 ~]# uptime 10:18:40 up 7 days, 3:52, load average: 0.03, 0.01, 0.00 It has been working fine: Survey data from wlan0 frequency: 5240 MHz [in use] noise: -101 dBm channel active time: 593724580 ms channel busy time: 9706985 ms channel receive time: 2053580 ms channel transmit time: 6473058 ms Tested-by: John Deere <24601deerej@gmail.com>
On 5/7/20 11:03 AM, Venkateswara Naralasetty wrote: > Channel active/busy time are showing incorrect(less than previous or > sometimes zero) for successive survey dump command. > > example: > Survey data from wlan0 > frequency: 5180 MHz [in use] > channel active time: 54995 ms > channel busy time: 432 ms > channel receive time: 0 ms > channel transmit time: 59 ms > Survey data from wlan0 > frequency: 5180 MHz [in use] > channel active time: 32592 ms > channel busy time: 254 ms > channel receive time: 0 ms > channel transmit time: 0 ms > > This patch fix this issue by assigning 'wmi_bss_survey_req_type' > as 'WMI_BSS_SURVEY_REQ_TYPE_READ' which accumulate survey data in > FW and send survey data to driver upon the driver request. Wrap around > is taken care by FW. > > hardware used : QCA9984 > firmware ver : ver 10.4-3.5.3-00057 > > hardware used : QCA988X > firmware ver : 10.2.4-1.0-00047 > > Tested-by: Markus Theil <markus.theil@tu-ilmenau.de> > Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> > --- > v4: > * updated signed-off-by > > v3: > * Rebased on TOT and added Tested-by > > drivers/net/wireless/ath/ath10k/mac.c | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c > index a1147cc..9330b52 100644 > --- a/drivers/net/wireless/ath/ath10k/mac.c > +++ b/drivers/net/wireless/ath/ath10k/mac.c > @@ -7275,7 +7275,7 @@ ath10k_mac_update_bss_chan_survey(struct ath10k *ar, > struct ieee80211_channel *channel) > { > int ret; > - enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR; > + enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ; > > lockdep_assert_held(&ar->conf_mutex); > > I have tested this on a QCA9980 device on a TP-Link Archer A7v5 with the firmware version 10.2.4.70.70. [root@Archer-A7v5 ~]# uptime 10:18:40 up 7 days, 3:52, load average: 0.03, 0.01, 0.00 It has been working fine: Survey data from wlan0 frequency: 5240 MHz [in use] noise: -101 dBm channel active time: 593724580 ms channel busy time: 9706985 ms channel receive time: 2053580 ms channel transmit time: 6473058 ms Tested-by: John Deere <24601deerej@gmail.com>
I've seen this patch got dropped again from the ath.git pending branch. On which hw/firmware combination did it fail to operate? On 5/17/20 4:26 AM, John Deere wrote: > > On 5/7/20 11:03 AM, Venkateswara Naralasetty wrote: >> Channel active/busy time are showing incorrect(less than previous or >> sometimes zero) for successive survey dump command. >> >> example: >> Survey data from wlan0 >> frequency: 5180 MHz [in use] >> channel active time: 54995 ms >> channel busy time: 432 ms >> channel receive time: 0 ms >> channel transmit time: 59 ms >> Survey data from wlan0 >> frequency: 5180 MHz [in use] >> channel active time: 32592 ms >> channel busy time: 254 ms >> channel receive time: 0 ms >> channel transmit time: 0 ms >> >> This patch fix this issue by assigning 'wmi_bss_survey_req_type' >> as 'WMI_BSS_SURVEY_REQ_TYPE_READ' which accumulate survey data in >> FW and send survey data to driver upon the driver request. Wrap around >> is taken care by FW. >> >> hardware used : QCA9984 >> firmware ver : ver 10.4-3.5.3-00057 >> >> hardware used : QCA988X >> firmware ver : 10.2.4-1.0-00047 >> >> Tested-by: Markus Theil <markus.theil@tu-ilmenau.de> >> Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> >> --- >> v4: >> * updated signed-off-by >> >> v3: >> * Rebased on TOT and added Tested-by >> >> drivers/net/wireless/ath/ath10k/mac.c | 2 +- >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> diff --git a/drivers/net/wireless/ath/ath10k/mac.c >> b/drivers/net/wireless/ath/ath10k/mac.c >> index a1147cc..9330b52 100644 >> --- a/drivers/net/wireless/ath/ath10k/mac.c >> +++ b/drivers/net/wireless/ath/ath10k/mac.c >> @@ -7275,7 +7275,7 @@ ath10k_mac_update_bss_chan_survey(struct ath10k >> *ar, >> struct ieee80211_channel *channel) >> { >> int ret; >> - enum wmi_bss_survey_req_type type = >> WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR; >> + enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ; >> lockdep_assert_held(&ar->conf_mutex); >> > > > I have tested this on a QCA9980 device on a TP-Link Archer A7v5 with > the firmware version 10.2.4.70.70. > > [root@Archer-A7v5 ~]# uptime > 10:18:40 up 7 days, 3:52, load average: 0.03, 0.01, 0.00 > > > It has been working fine: > > Survey data from wlan0 > frequency: 5240 MHz [in use] > noise: -101 dBm > channel active time: 593724580 ms > channel busy time: 9706985 ms > channel receive time: 2053580 ms > channel transmit time: 6473058 ms > > Tested-by: John Deere <24601deerej@gmail.com> > > _______________________________________________ > ath10k mailing list > ath10k@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/ath10k
Markus Theil <markus.theil@tu-ilmenau.de> writes: > I've seen this patch got dropped again from the ath.git pending branch. > On which hw/firmware combination did it fail to operate? It's deferred at the moment: https://patchwork.kernel.org/patch/11532357/ The conclusion from the other thread was not clear for me, so I put it into deferred and will take a closer look once I have time.
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index a1147cc..9330b52 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -7275,7 +7275,7 @@ ath10k_mac_update_bss_chan_survey(struct ath10k *ar, struct ieee80211_channel *channel) { int ret; - enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR; + enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ; lockdep_assert_held(&ar->conf_mutex);