Patchwork ath10k project

login
register
mail settings

Incoming patches

« Previous 1 2 3 4 5 Next »
Filters: State = Action Required remove filter    |    Archived = No remove filter
Patch A/R/T Date Submitter Delegate State
[v2] ath10k: transmit queued frames after waking queues - - - 2018-05-21 Niklas Cassel New
ath10k: transmit queued frames after waking queues - - - 2018-05-17 Niklas Cassel New
[PATCHv2,2/2] ath10k: DFS Host Confirmation - - - 2018-05-15 Sriram R New
[PATCHv2,1/2] ath: Add support to get the detected radar specifications - - - 2018-05-15 Sriram R New
[PATCHv2,2/2] ath10k: DFS Host Confirmation - - - 2018-05-15 Sriram R New
[PATCHv2,1/2] ath: Add support to get the detected radar specifications - - - 2018-05-15 Sriram R New
[v2,3/3] ath10k: Support survey dump for ath10k-ct 10.1 firmware. - - - 2018-05-14 Ben Greear New
[v2,2/3] ath10k: Don't try un-supported idle_ps_config command. - - - 2018-05-14 Ben Greear New
[v2,1/3] ath10k: Add ath10k-ct firmware feature flags and descriptions. - - - 2018-05-14 Ben Greear New
ath10k: Add support to configure channel dwell time - - - 2018-05-12 Pradeep Kumar Chitrapu New
[3/3] ath10k: Support survey dump for ath10k-ct 10.1 firmware. - - - 2018-05-11 Ben Greear New
[2/3] ath10k: Don't try un-supported idle_ps_config command. - - - 2018-05-11 Ben Greear New
[1/3] ath10k: Add ath10k-ct firmware feature flags and descriptions. - - - 2018-05-11 Ben Greear New
[v2] ath10k: Replace bit shifts with the BIT() macro for rx desc bits - - - 2018-05-09 Govind Singh New
ath10k: hw: make consistent usage of ATH10K_FW_DIR in paths - - - 2018-05-09 Marcus Folkesson New
ath10k: Replace bit shifts with the BIT() macro for rx desc bits - - - 2018-05-09 Govind Singh New
ath10k: add fw crash dump support for QCA9888 and QCA99X0 - - - 2018-05-08 Anilkumar Kolli New
[v2] ath10k: support for multicast rate control - - - 2018-05-08 Pradeep Kumar Chitrapu New
[v2] ath10k: remove variables which set but not used - - - 2018-05-07 Kenneth Lu New
ath10k: fix return value check in wake_tx_q op - - - 2018-05-06 Erik Stromdahl New
ath10k: snoc: Remove owner assignment from platform_driver - - - 2018-05-05 Fabio Estevam New
ath10k: add dynamic vlan support - - - 2018-05-04 mpubbise@codeaurora.org New
ath10k: add quiet mode support for QCA6174/QCA9377 - - - 2018-05-03 Yu Wang New
[v7] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-30 Sebastian Gottschall New
[2/2] ath10k: DFS Host Confirmation - - - 2018-04-30 Sriram R New
[1/2] ath: Add support to get the detected radar specifications - - - 2018-04-30 Sriram R New
[2/2,-,linux-stable-4.4] ath10k: rebuild crypto header in rx data frames - - - 2018-04-30 Sriram R New
[1/2,linux-stable-4.4] ath10k: Add new hw param to identify alignment for different chipsets - - - 2018-04-30 Sriram R New
[v5] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-29 Sebastian Gottschall New
[v4] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-28 Sebastian Gottschall New
[v2] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-27 Ben Greear New
[v3] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-27 Sebastian Gottschall New
ath10k: sdio: jump to correct label in error handling path - - - 2018-04-26 Niklas Cassel New
[v1] ath10k: fix band_center_freq handling for VHT160 in recent firmwares - - - 2018-04-26 Sebastian Gottschall New
[v2] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-26 Sebastian Gottschall New
[v1] ath10k: fix crash in recent 3.5.3 9984 firmware due wrong handling of peer_bw_rxnss_override parameter - - - 2018-04-26 Sebastian Gottschall New
[next] ath10k: fix spelling mistake: "servive" -> "service" - - - 2018-04-26 Colin Ian King New
[2/2] usb: typec: fix formatting errors that cause build breakage - - - 2018-04-25 Andres Rodriguez New
[1/2] firmware: some documentation fixes - - - 2018-04-25 Andres Rodriguez New
9984 with 10.4.3.5.3-0057 crashes - - - 2018-04-24 Sebastian Gottschall New
[9/9] ath10k: re-enable the firmware fallback mechanism for testmode 1 - - 2018-04-23 Andres Rodriguez New
[8/9] ath10k: use request_firmware_nowarn to load firmware 1 - - 2018-04-23 Andres Rodriguez New
[7/9] firmware: use rename fw_sysfs_fallback to use the firmware_ prefix - - - 2018-04-23 Andres Rodriguez New
[6/9] firmware: print firmware name on fallback path - - - 2018-04-23 Andres Rodriguez New
[5/9] firmware: add function to load firmware without warnings v5 - - - 2018-04-23 Andres Rodriguez New
[4/9] firmware: use () to terminate kernel-doc function names 1 - - 2018-04-23 Andres Rodriguez New
[3/9] firmware: add kernel-doc for enum fw_opt - - - 2018-04-23 Andres Rodriguez New
[2/9] firmware: wrap FW_OPT_* into an enum - - - 2018-04-23 Andres Rodriguez New
[1/9] firmware: some documentation fixes - - - 2018-04-23 Andres Rodriguez New
[PATCHv3] ath10k: fix kernel panic while reading tpc_stats - - - 2018-04-23 tamizhr@codeaurora.org New
[RFC,v2] ath10k: report tx rate using ieee80211_tx_status() - - - 2018-04-21 Anilkumar Kolli New
[v1,1/1] ath10k: convert kmemdup to dma_alloc_coherent - - - 2018-04-20 Jared Bents New
ath10k: add dynamic vlan support - - - 2018-04-20 mpubbise@codeaurora.org New
[v2,3/3] ath10k: Support ethtool gstats2 API. - - - 2018-04-19 Ben Greear New
[v2,2/3] mac80211: Add support for ethtool gstats2 API. - - - 2018-04-19 Ben Greear New
[v2,1/3] ethtool: Support ETHTOOL_GSTATS2 command. - - - 2018-04-19 Ben Greear New
[3/3] ath10k: Support ethtool gstats2 API. - - - 2018-04-18 Ben Greear New
[2/3] mac80211: Add support for ethtool gstats2 API. - - - 2018-04-18 Ben Greear New
[1/3] ethtool: Support ETHTOOL_GSTATS2 command. - - - 2018-04-18 Ben Greear New
[v2,4/4] ath10k: Enable sta idle power save - - - 2018-04-17 Rakesh Pillai New
[v2,3/4] ath10k: Enable SRRI/DRRI support on ddr for WCN3990 - - - 2018-04-17 Rakesh Pillai New
[v2,2/4] ath10k: Add support for shadow register for WNC3990 - - - 2018-04-17 Rakesh Pillai New
[v2,1/4] ath10k: Add hw params for shadow register support - - - 2018-04-17 Rakesh Pillai New
[v2] ath10k: Enable hw checksum for wcn3990 - - - 2018-04-17 Rakesh Pillai New
[PATCHv2,3/3] ath10k: average ack rssi support for data frames - - - 2018-04-16 Balaji Pothunoori New
[PATCHv2,2/3] mac80211: average ack rssi support for data frames - - - 2018-04-16 Balaji Pothunoori New
[PATCHv2,1/3] cfg80211: average ack rssi support for data frames - - - 2018-04-16 Balaji Pothunoori New
ath10k: Fix fw path name for WCN3990 target - - - 2018-04-16 Govind Singh New
[2/2] ath10k: add inlined wrappers for htt rx ops - - - 2018-04-15 Erik Stromdahl New
[1/2] ath10k: add inlined wrappers for htt tx ops - - - 2018-04-15 Erik Stromdahl New
[v2] ath10k: search all IEs for variant before falling back - - - 2018-04-13 Kalle Valo New
[3/3] ath10k: average ack rssi support for data frames - - - 2018-04-13 Balaji Pothunoori New
ath10k: Fix a typo in ath10k_wmi_set_wmm_param() - - - 2018-04-13 mkenna@codeaurora.org New
ath10k: Fix a typo in ath10k_wmi_set_wmm_param() - - - 2018-04-13 mkenna@codeaurora.org New
ath10k: correct target assert problem due to CE5 stuck - - - 2018-04-12 mpubbise@codeaurora.org New
ath10k: correct target assert problem due to CE5 stuck - - - 2018-04-12 mpubbise@qti.qualcomm.com New
ath10k:add support for multicast rate control - - - 2018-04-12 Sven Eckelmann New
[v2] ath10k: Convert wow pattern from 802.3 to 802.11 - - - 2018-04-12 Wen Gong New
ath10k:add support for multicast rate control - - - 2018-04-12 Pradeep Kumar Chitrapu New
[v2,13/13] dt: bindings: add bindings for wcn3990 wifi block - 1 - 2018-04-10 Govind Singh New
[4/4] ath10k: Enable sta idle power save - - - 2018-04-10 Rakesh Pillai New
[3/4] ath10k: Enable SRRI/DRRI support on ddr for WCN3990 - - - 2018-04-10 Rakesh Pillai New
[2/4] ath10k: Add support for shadow register for WNC3990 - - - 2018-04-10 Rakesh Pillai New
[1/4] ath10k: Add hw params for shadow register support - - - 2018-04-10 Rakesh Pillai New
ath10k: fix tlv 5ghz channel missing issue - - - 2018-04-10 zhichen@codeaurora.org New
ath10k: fixed scan crash - - - 2018-04-10 zhichen@codeaurora.org New
[v13] ath10k: add LED and GPIO controlling support for various chipsets - 1 1 2018-04-06 Kalle Valo New
ath10k: Enable hw checksum for wcn3990 - - - 2018-04-06 Rakesh Pillai New
ath10k: Convert wow pattern from 802.3 to 802.11 - 1 1 2018-03-30 Wen Gong New
[2/2] ath10k: support MAC address randomization in scan - - - 2018-03-30 Carl Huang New
[1/2] ath10k: Add WMI_SERVICE_AVAILABLE_EVENT support - - - 2018-03-30 Carl Huang New
ath10k: fix spelling mistake: "tiggers" -> "triggers" - - - 2018-03-29 Colin Ian King New
[PATCHv3] ath10k: Add tx ack signal support for management frames - - - 2018-03-29 Venkateswara Naralasetty New
ath10k: avoid possible string overflow - - - 2018-03-28 Arnd Bergmann New
ath10k: sdio: fix memory leak for probe allocations - - - 2018-03-27 Marcus Folkesson New
[v1,1/1] ath10k: convert kmemdup to dma_alloc_coherent - - - 2018-03-26 Jared Bents New
[2/2] ath10k: add memory dump support QCA9984 - - - 2018-03-26 Kalle Valo New
[1/2] ath10k: refactor ath10k_pci_dump_memory() in preparation for QCA9984 support - - - 2018-03-26 Kalle Valo New
ath10k: Suppress "Unknown eventid: 36925" warnings - - - 2018-03-26 Sathishkumar Muruganandam New
[12/12] ath10k: Add qmi wlan enable/disable support for WCN3990 - - - 2018-03-26 Govind Singh New
« Previous 1 2 3 4 5 Next »