| Message ID | 20201031184854.745828-37-jic23@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | dt-bindings:iio: yet more txt to yam conversions | expand |
On Sat, 31 Oct 2020 18:48:44 +0000 Jonathan Cameron <jic23@kernel.org> wrote: > From: Jonathan Cameron <Jonathan.Cameron@huawei.com> > > Straight forward conversion. Not heard from Ivan in a while so if the > email bounces, I'll change the maintainer to myself for this binding unless > anyone else comes forwards. > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> > Cc: Ivan T. Ivanov <iivanov@mm-sol.com> Ivan's email is bouncing, so I've put myself as temporary maintainer on this one until someone else steps up. Otherwise, dropped $ref for standard unit case -ohms as suggested by RobH. Applied to the togreg branch of iio.git and pushed out as testing for all the normal reasons. Thanks, Jonathan > --- > .../bindings/iio/adc/qcom,spmi-iadc.txt | 46 -------------- > .../bindings/iio/adc/qcom,spmi-iadc.yaml | 62 +++++++++++++++++++ > 2 files changed, 62 insertions(+), 46 deletions(-) > > diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt > deleted file mode 100644 > index 4e36d6e2f7b6..000000000000 > --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt > +++ /dev/null > @@ -1,46 +0,0 @@ > -Qualcomm's SPMI PMIC current ADC > - > -QPNP PMIC current ADC (IADC) provides interface to clients to read current. > -A 16 bit ADC is used for current measurements. IADC can measure the current > -through an external resistor (channel 1) or internal (built-in) resistor > -(channel 0). When using an external resistor it is to be described by > -qcom,external-resistor-micro-ohms property. > - > -IADC node: > - > -- compatible: > - Usage: required > - Value type: <string> > - Definition: Should contain "qcom,spmi-iadc". > - > -- reg: > - Usage: required > - Value type: <prop-encoded-array> > - Definition: IADC base address and length in the SPMI PMIC register map > - > -- interrupts: > - Usage: optional > - Value type: <prop-encoded-array> > - Definition: End of ADC conversion. > - > -- qcom,external-resistor-micro-ohms: > - Usage: optional > - Value type: <u32> > - Definition: Sense resister value in micro Ohm. > - If not defined value of 10000 micro Ohms will be used. > - > -Example: > - /* IADC node */ > - pmic_iadc: iadc@3600 { > - compatible = "qcom,spmi-iadc"; > - reg = <0x3600 0x100>; > - interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; > - qcom,external-resistor-micro-ohms = <10000>; > - #io-channel-cells = <1>; > - }; > - > - /* IIO client node */ > - bat { > - io-channels = <&pmic_iadc 0>; > - io-channel-names = "iadc"; > - }; > diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml > new file mode 100644 > index 000000000000..359e1ede0ae2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml > @@ -0,0 +1,62 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-iadc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm's SPMI PMIC current ADC > + > +maintainers: > + - Ivan T. Ivanov <iivanov@mm-sol.com> > + > +description: | > + QPNP PMIC current ADC (IADC) provides interface to clients to read current. > + A 16 bit ADC is used for current measurements. IADC can measure the current > + through an external resistor (channel 1) or internal (built-in) resistor > + (channel 0). When using an external resistor it is to be described by > + qcom,external-resistor-micro-ohms property. > + > +properties: > + compatible: > + const: qcom,spmi-iadc > + > + reg: > + description: IADC base address and length in the SPMI PMIC register map > + maxItems: 1 > + > + qcom,external-resistor-micro-ohms: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Sensor resistor value. If not defined value of 10000 micro Ohms > + will be used. > + > + interrupts: > + maxItems: 1 > + description: > + End of conversion interrupt. > + > + "#io-channel-cells": > + const: 1 > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + spmi_bus { > + #address-cells = <1>; > + #size-cells = <0>; > + pmic_iadc: adc@3600 { > + compatible = "qcom,spmi-iadc"; > + reg = <0x3600 0x100>; > + interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; > + qcom,external-resistor-micro-ohms = <10000>; > + #io-channel-cells = <1>; > + }; > + }; > +... > +
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt deleted file mode 100644 index 4e36d6e2f7b6..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt +++ /dev/null @@ -1,46 +0,0 @@ -Qualcomm's SPMI PMIC current ADC - -QPNP PMIC current ADC (IADC) provides interface to clients to read current. -A 16 bit ADC is used for current measurements. IADC can measure the current -through an external resistor (channel 1) or internal (built-in) resistor -(channel 0). When using an external resistor it is to be described by -qcom,external-resistor-micro-ohms property. - -IADC node: - -- compatible: - Usage: required - Value type: <string> - Definition: Should contain "qcom,spmi-iadc". - -- reg: - Usage: required - Value type: <prop-encoded-array> - Definition: IADC base address and length in the SPMI PMIC register map - -- interrupts: - Usage: optional - Value type: <prop-encoded-array> - Definition: End of ADC conversion. - -- qcom,external-resistor-micro-ohms: - Usage: optional - Value type: <u32> - Definition: Sense resister value in micro Ohm. - If not defined value of 10000 micro Ohms will be used. - -Example: - /* IADC node */ - pmic_iadc: iadc@3600 { - compatible = "qcom,spmi-iadc"; - reg = <0x3600 0x100>; - interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; - qcom,external-resistor-micro-ohms = <10000>; - #io-channel-cells = <1>; - }; - - /* IIO client node */ - bat { - io-channels = <&pmic_iadc 0>; - io-channel-names = "iadc"; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml new file mode 100644 index 000000000000..359e1ede0ae2 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-iadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's SPMI PMIC current ADC + +maintainers: + - Ivan T. Ivanov <iivanov@mm-sol.com> + +description: | + QPNP PMIC current ADC (IADC) provides interface to clients to read current. + A 16 bit ADC is used for current measurements. IADC can measure the current + through an external resistor (channel 1) or internal (built-in) resistor + (channel 0). When using an external resistor it is to be described by + qcom,external-resistor-micro-ohms property. + +properties: + compatible: + const: qcom,spmi-iadc + + reg: + description: IADC base address and length in the SPMI PMIC register map + maxItems: 1 + + qcom,external-resistor-micro-ohms: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Sensor resistor value. If not defined value of 10000 micro Ohms + will be used. + + interrupts: + maxItems: 1 + description: + End of conversion interrupt. + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spmi_bus { + #address-cells = <1>; + #size-cells = <0>; + pmic_iadc: adc@3600 { + compatible = "qcom,spmi-iadc"; + reg = <0x3600 0x100>; + interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; + qcom,external-resistor-micro-ohms = <10000>; + #io-channel-cells = <1>; + }; + }; +... +