diff mbox series

[v3,3/3] phy: phy-mtk-tphy: add support mt8195

Message ID 1626331702-27825-3-git-send-email-chunfeng.yun@mediatek.com (mailing list archive)
State New, archived
Headers show
Series [v3,1/3] dt-bindings: phy: mediatek: tphy: add support hardware version 3 | expand

Commit Message

Chunfeng Yun (云春峰) July 15, 2021, 6:48 a.m. UTC 
The controller is designed to use use PLL integer mode, but
in fact used fractional mode for some ones on mt8195, this
causes signal degradation (e.g. eye diagram test fail), fix
it by switching PLL to 26Mhz from default 48Mhz to improve
signal quality.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~3: no changes
---
 drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

Comments

Vinod Koul July 20, 2021, 8:25 a.m. UTC | #1 
On 15-07-21, 14:48, Chunfeng Yun wrote:
> The controller is designed to use use PLL integer mode, but
> in fact used fractional mode for some ones on mt8195, this
> causes signal degradation (e.g. eye diagram test fail), fix
> it by switching PLL to 26Mhz from default 48Mhz to improve
> signal quality.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2~3: no changes
> ---
>  drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++
>  1 file changed, 52 insertions(+)
> 
> diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
> index 42a1174da6cc..c3dc1763a7eb 100644
> --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> @@ -41,6 +41,8 @@
>  
>  #define U3P_USBPHYACR0		0x000
>  #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> +#define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> +#define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
>  #define PA0_RG_USB20_INTR_EN		BIT(5)
>  
>  #define U3P_USBPHYACR1		0x004
> @@ -52,6 +54,8 @@
>  #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
>  
>  #define U3P_USBPHYACR2		0x008
> +#define PA2_RG_U2PLL_BW			GENMASK(21, 19)
> +#define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
>  #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
>  
>  #define U3P_USBPHYACR5		0x014
> @@ -73,6 +77,14 @@
>  #define P2C_USB20_GPIO_MODE		BIT(8)
>  #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
>  
> +#define U3P_U2PHYA_RESV		0x030
> +#define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
> +#define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
> +
> +#define U3P_U2PHYA_RESV1	0x044
> +#define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
> +#define P2R_RG_U2PLL_FRA_EN		BIT(3)
> +
>  #define U3D_U2PHYDCR0		0x060
>  #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
>  
> @@ -277,6 +289,12 @@ enum mtk_phy_version {
>  struct mtk_phy_pdata {
>  	/* avoid RX sensitivity level degradation only for mt8173 */
>  	bool avoid_rx_sen_degradation;
> +	/*
> +	 * u2phy should use integer mode instead of fractional mode of
> +	 * 48M PLL, fix it by switching PLL to 26M from default 48M
> +	 * for mt8195
> +	 */
> +	bool sw_pll_48m_to_26m;
>  	enum mtk_phy_version version;
>  };
>  
> @@ -456,6 +474,33 @@ static void u3_phy_instance_init(struct mtk_tphy *tphy,
>  	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
>  }
>  
> +static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
> +	struct mtk_phy_instance *instance)
> +{
> +	struct u2phy_banks *u2_banks = &instance->u2_banks;
> +	void __iomem *com = u2_banks->com;
> +	u32 tmp;
> +
> +	if (!tphy->pdata->sw_pll_48m_to_26m)
> +		return;
> +
> +	tmp = readl(com + U3P_USBPHYACR0);
> +	tmp &= ~PA0_USB20_PLL_PREDIV;
> +	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
> +	writel(tmp, com + U3P_USBPHYACR0);
> +
> +	tmp = readl(com + U3P_USBPHYACR2);
> +	tmp &= ~PA2_RG_U2PLL_BW;
> +	tmp |= PA2_RG_U2PLL_BW_VAL(3);
> +	writel(tmp, com + U3P_USBPHYACR2);
> +
> +	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
> +
> +	tmp = readl(com + U3P_U2PHYA_RESV1);
> +	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
> +	writel(tmp, com + U3P_U2PHYA_RESV1);
> +}
> +
>  static void u2_phy_instance_init(struct mtk_tphy *tphy,
>  	struct mtk_phy_instance *instance)
>  {
> @@ -941,6 +986,7 @@ static int mtk_phy_init(struct phy *phy)
>  
>  	switch (instance->type) {
>  	case PHY_TYPE_USB2:
> +		u2_phy_pll_26m_set(tphy, instance);

should this not be set only for MTK_PHY_V3?

>  		u2_phy_instance_init(tphy, instance);
>  		u2_phy_props_set(tphy, instance);
>  		break;
> @@ -1094,10 +1140,16 @@ static const struct mtk_phy_pdata mt8173_pdata = {
>  	.version = MTK_PHY_V1,
>  };
>  
> +static const struct mtk_phy_pdata mt8195_pdata = {
> +	.sw_pll_48m_to_26m = true,
> +	.version = MTK_PHY_V3,
> +};
> +
>  static const struct of_device_id mtk_tphy_id_table[] = {
>  	{ .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
>  	{ .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
>  	{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
> +	{ .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
>  	{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
>  	{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
>  	{ .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
> -- 
> 2.18.0
Chunfeng Yun (云春峰) July 21, 2021, 3:17 a.m. UTC | #2 
On Tue, 2021-07-20 at 13:55 +0530, Vinod Koul wrote:
> On 15-07-21, 14:48, Chunfeng Yun wrote:
> > The controller is designed to use use PLL integer mode, but
> > in fact used fractional mode for some ones on mt8195, this
> > causes signal degradation (e.g. eye diagram test fail), fix
> > it by switching PLL to 26Mhz from default 48Mhz to improve
> > signal quality.
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v2~3: no changes
> > ---
> >  drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++
> >  1 file changed, 52 insertions(+)
> > 
> > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
> > index 42a1174da6cc..c3dc1763a7eb 100644
> > --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> > @@ -41,6 +41,8 @@
> >  
> >  #define U3P_USBPHYACR0		0x000
> >  #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > +#define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> > +#define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
> >  #define PA0_RG_USB20_INTR_EN		BIT(5)
> >  
> >  #define U3P_USBPHYACR1		0x004
> > @@ -52,6 +54,8 @@
> >  #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
> >  
> >  #define U3P_USBPHYACR2		0x008
> > +#define PA2_RG_U2PLL_BW			GENMASK(21, 19)
> > +#define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
> >  #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> >  
> >  #define U3P_USBPHYACR5		0x014
> > @@ -73,6 +77,14 @@
> >  #define P2C_USB20_GPIO_MODE		BIT(8)
> >  #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> >  
> > +#define U3P_U2PHYA_RESV		0x030
> > +#define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
> > +#define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
> > +
> > +#define U3P_U2PHYA_RESV1	0x044
> > +#define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
> > +#define P2R_RG_U2PLL_FRA_EN		BIT(3)
> > +
> >  #define U3D_U2PHYDCR0		0x060
> >  #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> >  
> > @@ -277,6 +289,12 @@ enum mtk_phy_version {
> >  struct mtk_phy_pdata {
> >  	/* avoid RX sensitivity level degradation only for mt8173 */
> >  	bool avoid_rx_sen_degradation;
> > +	/*
> > +	 * u2phy should use integer mode instead of fractional mode of
> > +	 * 48M PLL, fix it by switching PLL to 26M from default 48M
> > +	 * for mt8195
> > +	 */
> > +	bool sw_pll_48m_to_26m;
> >  	enum mtk_phy_version version;
> >  };
> >  
> > @@ -456,6 +474,33 @@ static void u3_phy_instance_init(struct mtk_tphy *tphy,
> >  	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
> >  }
> >  
> > +static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
> > +	struct mtk_phy_instance *instance)
> > +{
> > +	struct u2phy_banks *u2_banks = &instance->u2_banks;
> > +	void __iomem *com = u2_banks->com;
> > +	u32 tmp;
> > +
> > +	if (!tphy->pdata->sw_pll_48m_to_26m)
> > +		return;
> > +
> > +	tmp = readl(com + U3P_USBPHYACR0);
> > +	tmp &= ~PA0_USB20_PLL_PREDIV;
> > +	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
> > +	writel(tmp, com + U3P_USBPHYACR0);
> > +
> > +	tmp = readl(com + U3P_USBPHYACR2);
> > +	tmp &= ~PA2_RG_U2PLL_BW;
> > +	tmp |= PA2_RG_U2PLL_BW_VAL(3);
> > +	writel(tmp, com + U3P_USBPHYACR2);
> > +
> > +	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
> > +
> > +	tmp = readl(com + U3P_U2PHYA_RESV1);
> > +	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
> > +	writel(tmp, com + U3P_U2PHYA_RESV1);
> > +}
> > +
> >  static void u2_phy_instance_init(struct mtk_tphy *tphy,
> >  	struct mtk_phy_instance *instance)
> >  {
> > @@ -941,6 +986,7 @@ static int mtk_phy_init(struct phy *phy)
> >  
> >  	switch (instance->type) {
> >  	case PHY_TYPE_USB2:
> > +		u2_phy_pll_26m_set(tphy, instance);
> 
> should this not be set only for MTK_PHY_V3?
Workaround only for mt8195, HW will fix it for others (V3)

Thanks

> 
> >  		u2_phy_instance_init(tphy, instance);
> >  		u2_phy_props_set(tphy, instance);
> >  		break;
> > @@ -1094,10 +1140,16 @@ static const struct mtk_phy_pdata mt8173_pdata = {
> >  	.version = MTK_PHY_V1,
> >  };
> >  
> > +static const struct mtk_phy_pdata mt8195_pdata = {
> > +	.sw_pll_48m_to_26m = true,
> > +	.version = MTK_PHY_V3,
> > +};
> > +
> >  static const struct of_device_id mtk_tphy_id_table[] = {
> >  	{ .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
> >  	{ .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
> >  	{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
> > +	{ .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
> >  	{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
> >  	{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
> >  	{ .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
> > -- 
> > 2.18.0
>
Vinod Koul July 22, 2021, 8:58 a.m. UTC | #3 
On 21-07-21, 11:17, Chunfeng Yun wrote:
> On Tue, 2021-07-20 at 13:55 +0530, Vinod Koul wrote:
> > On 15-07-21, 14:48, Chunfeng Yun wrote:
> > > The controller is designed to use use PLL integer mode, but
> > > in fact used fractional mode for some ones on mt8195, this
> > > causes signal degradation (e.g. eye diagram test fail), fix
> > > it by switching PLL to 26Mhz from default 48Mhz to improve
> > > signal quality.
> > > 
> > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > > ---
> > > v2~3: no changes
> > > ---
> > >  drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++
> > >  1 file changed, 52 insertions(+)
> > > 
> > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
> > > index 42a1174da6cc..c3dc1763a7eb 100644
> > > --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> > > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> > > @@ -41,6 +41,8 @@
> > >  
> > >  #define U3P_USBPHYACR0		0x000
> > >  #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > > +#define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> > > +#define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
> > >  #define PA0_RG_USB20_INTR_EN		BIT(5)
> > >  
> > >  #define U3P_USBPHYACR1		0x004
> > > @@ -52,6 +54,8 @@
> > >  #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
> > >  
> > >  #define U3P_USBPHYACR2		0x008
> > > +#define PA2_RG_U2PLL_BW			GENMASK(21, 19)
> > > +#define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
> > >  #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > >  
> > >  #define U3P_USBPHYACR5		0x014
> > > @@ -73,6 +77,14 @@
> > >  #define P2C_USB20_GPIO_MODE		BIT(8)
> > >  #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > >  
> > > +#define U3P_U2PHYA_RESV		0x030
> > > +#define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
> > > +#define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
> > > +
> > > +#define U3P_U2PHYA_RESV1	0x044
> > > +#define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
> > > +#define P2R_RG_U2PLL_FRA_EN		BIT(3)
> > > +
> > >  #define U3D_U2PHYDCR0		0x060
> > >  #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > >  
> > > @@ -277,6 +289,12 @@ enum mtk_phy_version {
> > >  struct mtk_phy_pdata {
> > >  	/* avoid RX sensitivity level degradation only for mt8173 */
> > >  	bool avoid_rx_sen_degradation;
> > > +	/*
> > > +	 * u2phy should use integer mode instead of fractional mode of
> > > +	 * 48M PLL, fix it by switching PLL to 26M from default 48M
> > > +	 * for mt8195
> > > +	 */
> > > +	bool sw_pll_48m_to_26m;
> > >  	enum mtk_phy_version version;
> > >  };
> > >  
> > > @@ -456,6 +474,33 @@ static void u3_phy_instance_init(struct mtk_tphy *tphy,
> > >  	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
> > >  }
> > >  
> > > +static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
> > > +	struct mtk_phy_instance *instance)
> > > +{
> > > +	struct u2phy_banks *u2_banks = &instance->u2_banks;
> > > +	void __iomem *com = u2_banks->com;
> > > +	u32 tmp;
> > > +
> > > +	if (!tphy->pdata->sw_pll_48m_to_26m)
> > > +		return;
> > > +
> > > +	tmp = readl(com + U3P_USBPHYACR0);
> > > +	tmp &= ~PA0_USB20_PLL_PREDIV;
> > > +	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
> > > +	writel(tmp, com + U3P_USBPHYACR0);
> > > +
> > > +	tmp = readl(com + U3P_USBPHYACR2);
> > > +	tmp &= ~PA2_RG_U2PLL_BW;
> > > +	tmp |= PA2_RG_U2PLL_BW_VAL(3);
> > > +	writel(tmp, com + U3P_USBPHYACR2);
> > > +
> > > +	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
> > > +
> > > +	tmp = readl(com + U3P_U2PHYA_RESV1);
> > > +	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
> > > +	writel(tmp, com + U3P_U2PHYA_RESV1);
> > > +}
> > > +
> > >  static void u2_phy_instance_init(struct mtk_tphy *tphy,
> > >  	struct mtk_phy_instance *instance)
> > >  {
> > > @@ -941,6 +986,7 @@ static int mtk_phy_init(struct phy *phy)
> > >  
> > >  	switch (instance->type) {
> > >  	case PHY_TYPE_USB2:
> > > +		u2_phy_pll_26m_set(tphy, instance);
> > 
> > should this not be set only for MTK_PHY_V3?
> Workaround only for mt8195, HW will fix it for others (V3)

Pls document that in comments here
Chunfeng Yun (云春峰) July 23, 2021, 6:30 a.m. UTC | #4 
On Thu, 2021-07-22 at 14:28 +0530, Vinod Koul wrote:
> On 21-07-21, 11:17, Chunfeng Yun wrote:
> > On Tue, 2021-07-20 at 13:55 +0530, Vinod Koul wrote:
> > > On 15-07-21, 14:48, Chunfeng Yun wrote:
> > > > The controller is designed to use use PLL integer mode, but
> > > > in fact used fractional mode for some ones on mt8195, this
> > > > causes signal degradation (e.g. eye diagram test fail), fix
> > > > it by switching PLL to 26Mhz from default 48Mhz to improve
> > > > signal quality.
> > > > 
> > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > > > ---
> > > > v2~3: no changes
> > > > ---
> > > >  drivers/phy/mediatek/phy-mtk-tphy.c | 52 +++++++++++++++++++++++++++++
> > > >  1 file changed, 52 insertions(+)
> > > > 
> > > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
> > > > index 42a1174da6cc..c3dc1763a7eb 100644
> > > > --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> > > > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> > > > @@ -41,6 +41,8 @@
> > > >  
> > > >  #define U3P_USBPHYACR0		0x000
> > > >  #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > > > +#define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> > > > +#define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
> > > >  #define PA0_RG_USB20_INTR_EN		BIT(5)
> > > >  
> > > >  #define U3P_USBPHYACR1		0x004
> > > > @@ -52,6 +54,8 @@
> > > >  #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
> > > >  
> > > >  #define U3P_USBPHYACR2		0x008
> > > > +#define PA2_RG_U2PLL_BW			GENMASK(21, 19)
> > > > +#define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
> > > >  #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > > >  
> > > >  #define U3P_USBPHYACR5		0x014
> > > > @@ -73,6 +77,14 @@
> > > >  #define P2C_USB20_GPIO_MODE		BIT(8)
> > > >  #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > > >  
> > > > +#define U3P_U2PHYA_RESV		0x030
> > > > +#define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
> > > > +#define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
> > > > +
> > > > +#define U3P_U2PHYA_RESV1	0x044
> > > > +#define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
> > > > +#define P2R_RG_U2PLL_FRA_EN		BIT(3)
> > > > +
> > > >  #define U3D_U2PHYDCR0		0x060
> > > >  #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > > >  
> > > > @@ -277,6 +289,12 @@ enum mtk_phy_version {
> > > >  struct mtk_phy_pdata {
> > > >  	/* avoid RX sensitivity level degradation only for mt8173 */
> > > >  	bool avoid_rx_sen_degradation;
> > > > +	/*
> > > > +	 * u2phy should use integer mode instead of fractional mode of
> > > > +	 * 48M PLL, fix it by switching PLL to 26M from default 48M
> > > > +	 * for mt8195
> > > > +	 */
> > > > +	bool sw_pll_48m_to_26m;
> > > >  	enum mtk_phy_version version;
> > > >  };
> > > >  
> > > > @@ -456,6 +474,33 @@ static void u3_phy_instance_init(struct mtk_tphy *tphy,
> > > >  	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
> > > >  }
> > > >  
> > > > +static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
> > > > +	struct mtk_phy_instance *instance)
> > > > +{
> > > > +	struct u2phy_banks *u2_banks = &instance->u2_banks;
> > > > +	void __iomem *com = u2_banks->com;
> > > > +	u32 tmp;
> > > > +
> > > > +	if (!tphy->pdata->sw_pll_48m_to_26m)
> > > > +		return;
> > > > +
> > > > +	tmp = readl(com + U3P_USBPHYACR0);
> > > > +	tmp &= ~PA0_USB20_PLL_PREDIV;
> > > > +	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
> > > > +	writel(tmp, com + U3P_USBPHYACR0);
> > > > +
> > > > +	tmp = readl(com + U3P_USBPHYACR2);
> > > > +	tmp &= ~PA2_RG_U2PLL_BW;
> > > > +	tmp |= PA2_RG_U2PLL_BW_VAL(3);
> > > > +	writel(tmp, com + U3P_USBPHYACR2);
> > > > +
> > > > +	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
> > > > +
> > > > +	tmp = readl(com + U3P_U2PHYA_RESV1);
> > > > +	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
> > > > +	writel(tmp, com + U3P_U2PHYA_RESV1);
> > > > +}
> > > > +
> > > >  static void u2_phy_instance_init(struct mtk_tphy *tphy,
> > > >  	struct mtk_phy_instance *instance)
> > > >  {
> > > > @@ -941,6 +986,7 @@ static int mtk_phy_init(struct phy *phy)
> > > >  
> > > >  	switch (instance->type) {
> > > >  	case PHY_TYPE_USB2:
> > > > +		u2_phy_pll_26m_set(tphy, instance);
> > > 
> > > should this not be set only for MTK_PHY_V3?
> > Workaround only for mt8195, HW will fix it for others (V3)
> 
> Pls document that in comments here

Ok, thanks
>
diff mbox series

Patch

diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 42a1174da6cc..c3dc1763a7eb 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -41,6 +41,8 @@ 
 
 #define U3P_USBPHYACR0		0x000
 #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+#define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
+#define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
 #define PA0_RG_USB20_INTR_EN		BIT(5)
 
 #define U3P_USBPHYACR1		0x004
@@ -52,6 +54,8 @@ 
 #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
 
 #define U3P_USBPHYACR2		0x008
+#define PA2_RG_U2PLL_BW			GENMASK(21, 19)
+#define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
 #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
 
 #define U3P_USBPHYACR5		0x014
@@ -73,6 +77,14 @@ 
 #define P2C_USB20_GPIO_MODE		BIT(8)
 #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
 
+#define U3P_U2PHYA_RESV		0x030
+#define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
+#define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
+
+#define U3P_U2PHYA_RESV1	0x044
+#define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
+#define P2R_RG_U2PLL_FRA_EN		BIT(3)
+
 #define U3D_U2PHYDCR0		0x060
 #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
 
@@ -277,6 +289,12 @@  enum mtk_phy_version {
 struct mtk_phy_pdata {
 	/* avoid RX sensitivity level degradation only for mt8173 */
 	bool avoid_rx_sen_degradation;
+	/*
+	 * u2phy should use integer mode instead of fractional mode of
+	 * 48M PLL, fix it by switching PLL to 26M from default 48M
+	 * for mt8195
+	 */
+	bool sw_pll_48m_to_26m;
 	enum mtk_phy_version version;
 };
 
@@ -456,6 +474,33 @@  static void u3_phy_instance_init(struct mtk_tphy *tphy,
 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
 }
 
+static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
+	struct mtk_phy_instance *instance)
+{
+	struct u2phy_banks *u2_banks = &instance->u2_banks;
+	void __iomem *com = u2_banks->com;
+	u32 tmp;
+
+	if (!tphy->pdata->sw_pll_48m_to_26m)
+		return;
+
+	tmp = readl(com + U3P_USBPHYACR0);
+	tmp &= ~PA0_USB20_PLL_PREDIV;
+	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
+	writel(tmp, com + U3P_USBPHYACR0);
+
+	tmp = readl(com + U3P_USBPHYACR2);
+	tmp &= ~PA2_RG_U2PLL_BW;
+	tmp |= PA2_RG_U2PLL_BW_VAL(3);
+	writel(tmp, com + U3P_USBPHYACR2);
+
+	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
+
+	tmp = readl(com + U3P_U2PHYA_RESV1);
+	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
+	writel(tmp, com + U3P_U2PHYA_RESV1);
+}
+
 static void u2_phy_instance_init(struct mtk_tphy *tphy,
 	struct mtk_phy_instance *instance)
 {
@@ -941,6 +986,7 @@  static int mtk_phy_init(struct phy *phy)
 
 	switch (instance->type) {
 	case PHY_TYPE_USB2:
+		u2_phy_pll_26m_set(tphy, instance);
 		u2_phy_instance_init(tphy, instance);
 		u2_phy_props_set(tphy, instance);
 		break;
@@ -1094,10 +1140,16 @@  static const struct mtk_phy_pdata mt8173_pdata = {
 	.version = MTK_PHY_V1,
 };
 
+static const struct mtk_phy_pdata mt8195_pdata = {
+	.sw_pll_48m_to_26m = true,
+	.version = MTK_PHY_V3,
+};
+
 static const struct of_device_id mtk_tphy_id_table[] = {
 	{ .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
 	{ .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
 	{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
+	{ .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
 	{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
 	{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
 	{ .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },