@@ -14430,6 +14430,13 @@ S: Maintained
F: Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt
F: drivers/pci/controller/dwc/pcie-histb.c
+PCIE DRIVER FOR INTEL KEEM BAY
+M: Srikanth Thokala <srikanth.thokala@intel.com>
+L: linux-pci@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/pci/intel,keembay-pcie*
+F: drivers/pci/controller/dwc/pcie-keembay.c
+
PCIE DRIVER FOR MEDIATEK
M: Ryder Lee <ryder.lee@mediatek.com>
M: Jianjun Wang <jianjun.wang@mediatek.com>
@@ -225,6 +225,34 @@ config PCIE_INTEL_GW
The PCIe controller uses the DesignWare core plus Intel-specific
hardware wrappers.
+config PCIE_KEEMBAY
+ bool
+
+config PCIE_KEEMBAY_HOST
+ bool "Intel Keem Bay PCIe controller - Host mode"
+ depends on ARCH_KEEMBAY || COMPILE_TEST
+ depends on PCI && PCI_MSI_IRQ_DOMAIN
+ select PCIE_DW_HOST
+ select PCIE_KEEMBAY
+ help
+ Say 'Y' here to enable support for the PCIe controller in Keem Bay
+ to work in host mode.
+ The PCIe controller is based on DesignWare Hardware and uses
+ DesignWare core functions.
+
+config PCIE_KEEMBAY_EP
+ bool "Intel Keem Bay PCIe controller - Endpoint mode"
+ depends on ARCH_KEEMBAY || COMPILE_TEST
+ depends on PCI && PCI_MSI_IRQ_DOMAIN
+ depends on PCI_ENDPOINT
+ select PCIE_DW_EP
+ select PCIE_KEEMBAY
+ help
+ Say 'Y' here to enable support for the PCIe controller in Keem Bay
+ to work in endpoint mode.
+ The PCIe controller is based on DesignWare Hardware and uses
+ DesignWare core functions.
+
config PCIE_KIRIN
depends on OF && (ARM64 || COMPILE_TEST)
bool "HiSilicon Kirin series SoCs PCIe controllers"
@@ -15,6 +15,7 @@ obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
obj-$(CONFIG_PCIE_INTEL_GW) += pcie-intel-gw.o
+obj-$(CONFIG_PCIE_KEEMBAY) += pcie-keembay.o
obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
obj-$(CONFIG_PCI_MESON) += pci-meson.o
new file mode 100644
@@ -0,0 +1,460 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PCIe controller driver for Intel Keem Bay
+ * Copyright (C) 2020 Intel Corporation
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/iopoll.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#include "pcie-designware.h"
+
+/* PCIE_REGS_APB_SLV Registers */
+#define PCIE_REGS_PCIE_CFG 0x0004
+#define PCIE_DEVICE_TYPE BIT(8)
+#define PCIE_RSTN BIT(0)
+#define PCIE_REGS_PCIE_APP_CNTRL 0x0008
+#define APP_LTSSM_ENABLE BIT(0)
+#define PCIE_REGS_INTERRUPT_ENABLE 0x0028
+#define MSI_CTRL_INT_EN BIT(8)
+#define EDMA_INT_EN GENMASK(7, 0)
+#define PCIE_REGS_INTERRUPT_STATUS 0x002c
+#define MSI_CTRL_INT BIT(8)
+#define PCIE_REGS_PCIE_SII_PM_STATE 0x00b0
+#define SMLH_LINK_UP BIT(19)
+#define RDLH_LINK_UP BIT(8)
+#define PCIE_REGS_PCIE_SII_LINK_UP (SMLH_LINK_UP | RDLH_LINK_UP)
+#define PCIE_REGS_PCIE_PHY_CNTL 0x0164
+#define PHY0_SRAM_BYPASS BIT(8)
+#define PCIE_REGS_PCIE_PHY_STAT 0x0168
+#define PHY0_MPLLA_STATE BIT(1)
+#define PCIE_REGS_LJPLL_STA 0x016c
+#define LJPLL_LOCK BIT(0)
+#define PCIE_REGS_LJPLL_CNTRL_0 0x0170
+#define LJPLL_EN BIT(29)
+#define LJPLL_FOUT_EN GENMASK(24, 21)
+#define PCIE_REGS_LJPLL_CNTRL_2 0x0178
+#define LJPLL_REF_DIV GENMASK(17, 12)
+#define LJPLL_FB_DIV GENMASK(11, 0)
+#define PCIE_REGS_LJPLL_CNTRL_3 0x017c
+#define LJPLL_POST_DIV3A GENMASK(24, 22)
+#define LJPLL_POST_DIV2A GENMASK(18, 16)
+
+#define PERST_DELAY_US 1000
+#define AUX_CLK_RATE_HZ 24000000
+
+struct keembay_pcie {
+ struct dw_pcie pci;
+ void __iomem *apb_base;
+ enum dw_pcie_device_mode mode;
+
+ struct clk *clk_master;
+ struct clk *clk_aux;
+ struct gpio_desc *reset;
+};
+
+struct keembay_pcie_of_data {
+ enum dw_pcie_device_mode mode;
+};
+
+static void keembay_ep_reset_assert(struct keembay_pcie *pcie)
+{
+ gpiod_set_value_cansleep(pcie->reset, 1);
+ usleep_range(PERST_DELAY_US, PERST_DELAY_US + 500);
+}
+
+static void keembay_ep_reset_deassert(struct keembay_pcie *pcie)
+{
+ /*
+ * Ensure that PERST# is asserted for a minimum of 100ms.
+ *
+ * For more details, refer to PCI Express Card Electromechanical
+ * Specification Revision 1.1, Table-2.4.
+ */
+ msleep(100);
+
+ gpiod_set_value_cansleep(pcie->reset, 0);
+ usleep_range(PERST_DELAY_US, PERST_DELAY_US + 500);
+}
+
+static void keembay_pcie_ltssm_set(struct keembay_pcie *pcie, bool enable)
+{
+ u32 val;
+
+ val = readl(pcie->apb_base + PCIE_REGS_PCIE_APP_CNTRL);
+ if (enable)
+ val |= APP_LTSSM_ENABLE;
+ else
+ val &= ~APP_LTSSM_ENABLE;
+ writel(val, pcie->apb_base + PCIE_REGS_PCIE_APP_CNTRL);
+}
+
+static int keembay_pcie_link_up(struct dw_pcie *pci)
+{
+ struct keembay_pcie *pcie = dev_get_drvdata(pci->dev);
+ u32 val;
+
+ val = readl(pcie->apb_base + PCIE_REGS_PCIE_SII_PM_STATE);
+
+ return (val & PCIE_REGS_PCIE_SII_LINK_UP) == PCIE_REGS_PCIE_SII_LINK_UP;
+}
+
+static int keembay_pcie_start_link(struct dw_pcie *pci)
+{
+ struct keembay_pcie *pcie = dev_get_drvdata(pci->dev);
+ u32 val;
+ int ret;
+
+ if (pcie->mode == DW_PCIE_EP_TYPE)
+ return 0;
+
+ keembay_pcie_ltssm_set(pcie, false);
+
+ ret = readl_poll_timeout(pcie->apb_base + PCIE_REGS_PCIE_PHY_STAT,
+ val, val & PHY0_MPLLA_STATE, 20,
+ 500 * USEC_PER_MSEC);
+ if (ret) {
+ dev_err(pci->dev, "MPLLA is not locked\n");
+ return ret;
+ }
+
+ keembay_pcie_ltssm_set(pcie, true);
+
+ return 0;
+}
+
+static void keembay_pcie_stop_link(struct dw_pcie *pci)
+{
+ struct keembay_pcie *pcie = dev_get_drvdata(pci->dev);
+
+ keembay_pcie_ltssm_set(pcie, false);
+}
+
+static const struct dw_pcie_ops keembay_pcie_ops = {
+ .link_up = keembay_pcie_link_up,
+ .start_link = keembay_pcie_start_link,
+ .stop_link = keembay_pcie_stop_link,
+};
+
+static inline struct clk *keembay_pcie_probe_clock(struct device *dev,
+ const char *id, u64 rate)
+{
+ struct clk *clk;
+ int ret;
+
+ clk = devm_clk_get(dev, id);
+ if (IS_ERR(clk))
+ return clk;
+
+ if (rate) {
+ ret = clk_set_rate(clk, rate);
+ if (ret)
+ return ERR_PTR(ret);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ERR_PTR(ret);
+
+ ret = devm_add_action_or_reset(dev,
+ (void(*)(void *))clk_disable_unprepare,
+ clk);
+ if (ret)
+ return ERR_PTR(ret);
+
+ return clk;
+}
+
+static int keembay_pcie_probe_clocks(struct keembay_pcie *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ struct device *dev = pci->dev;
+
+ pcie->clk_master = keembay_pcie_probe_clock(dev, "master", 0);
+ if (IS_ERR(pcie->clk_master))
+ return dev_err_probe(dev, PTR_ERR(pcie->clk_master),
+ "Failed to enable master clock");
+
+ pcie->clk_aux = keembay_pcie_probe_clock(dev, "aux", AUX_CLK_RATE_HZ);
+ if (IS_ERR(pcie->clk_aux))
+ return dev_err_probe(dev, PTR_ERR(pcie->clk_aux),
+ "Failed to enable auxiliary clock");
+
+ return 0;
+}
+
+/*
+ * Initialize the internal PCIe PLL in Host mode.
+ * See the following sections in Keem Bay data book,
+ * (1) 6.4.6.1 PCIe Subsystem Example Initialization,
+ * (2) 6.8 PCIe Low Jitter PLL for Ref Clk Generation.
+ */
+static int keembay_pcie_pll_init(struct keembay_pcie *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ u32 val;
+ int ret;
+
+ val = FIELD_PREP(LJPLL_REF_DIV, 0) | FIELD_PREP(LJPLL_FB_DIV, 0x32);
+ writel(val, pcie->apb_base + PCIE_REGS_LJPLL_CNTRL_2);
+
+ val = FIELD_PREP(LJPLL_POST_DIV3A, 0x2) |
+ FIELD_PREP(LJPLL_POST_DIV2A, 0x2);
+ writel(val, pcie->apb_base + PCIE_REGS_LJPLL_CNTRL_3);
+
+ val = FIELD_PREP(LJPLL_EN, 0x1) | FIELD_PREP(LJPLL_FOUT_EN, 0xc);
+ writel(val, pcie->apb_base + PCIE_REGS_LJPLL_CNTRL_0);
+
+ ret = readl_poll_timeout(pcie->apb_base + PCIE_REGS_LJPLL_STA,
+ val, val & LJPLL_LOCK, 20,
+ 500 * USEC_PER_MSEC);
+ if (ret)
+ dev_err(pci->dev, "Low jitter PLL is not locked\n");
+
+ return ret;
+}
+
+static void keembay_pcie_msi_irq_handler(struct irq_desc *desc)
+{
+ struct keembay_pcie *pcie = irq_desc_get_handler_data(desc);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+ u32 val, mask, status;
+ struct pcie_port *pp;
+
+ /*
+ * Keem Bay PCIe Controller provides an additional IP logic on top of
+ * standard DWC IP to clear MSI IRQ by writing '1' to the respective
+ * bit of the status register.
+ *
+ * So, a chained irq handler is defined to handle this additional
+ * IP logic.
+ */
+
+ chained_irq_enter(chip, desc);
+
+ pp = &pcie->pci.pp;
+ val = readl(pcie->apb_base + PCIE_REGS_INTERRUPT_STATUS);
+ mask = readl(pcie->apb_base + PCIE_REGS_INTERRUPT_ENABLE);
+
+ status = val & mask;
+
+ if (status & MSI_CTRL_INT) {
+ dw_handle_msi_irq(pp);
+ writel(status, pcie->apb_base + PCIE_REGS_INTERRUPT_STATUS);
+ }
+
+ chained_irq_exit(chip, desc);
+}
+
+static int keembay_pcie_setup_msi_irq(struct keembay_pcie *pcie)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ struct device *dev = pci->dev;
+ struct platform_device *pdev = to_platform_device(dev);
+ int irq;
+
+ irq = platform_get_irq_byname(pdev, "pcie");
+ if (irq < 0)
+ return irq;
+
+ irq_set_chained_handler_and_data(irq, keembay_pcie_msi_irq_handler,
+ pcie);
+
+ return 0;
+}
+
+static void keembay_pcie_ep_init(struct dw_pcie_ep *ep)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+ struct keembay_pcie *pcie = dev_get_drvdata(pci->dev);
+
+ writel(EDMA_INT_EN, pcie->apb_base + PCIE_REGS_INTERRUPT_ENABLE);
+}
+
+static int keembay_pcie_ep_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
+ enum pci_epc_irq_type type,
+ u16 interrupt_num)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+
+ switch (type) {
+ case PCI_EPC_IRQ_LEGACY:
+ /* Legacy interrupts are not supported in Keem Bay */
+ dev_err(pci->dev, "Legacy IRQ is not supported\n");
+ return -EINVAL;
+ case PCI_EPC_IRQ_MSI:
+ return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num);
+ case PCI_EPC_IRQ_MSIX:
+ return dw_pcie_ep_raise_msix_irq(ep, func_no, interrupt_num);
+ default:
+ dev_err(pci->dev, "Unknown IRQ type %d\n", type);
+ return -EINVAL;
+ }
+}
+
+static const struct pci_epc_features keembay_pcie_epc_features = {
+ .linkup_notifier = false,
+ .msi_capable = true,
+ .msix_capable = true,
+ .reserved_bar = BIT(BAR_1) | BIT(BAR_3) | BIT(BAR_5),
+ .bar_fixed_64bit = BIT(BAR_0) | BIT(BAR_2) | BIT(BAR_4),
+ .align = SZ_16K,
+};
+
+static const struct pci_epc_features *
+keembay_pcie_get_features(struct dw_pcie_ep *ep)
+{
+ return &keembay_pcie_epc_features;
+}
+
+static const struct dw_pcie_ep_ops keembay_pcie_ep_ops = {
+ .ep_init = keembay_pcie_ep_init,
+ .raise_irq = keembay_pcie_ep_raise_irq,
+ .get_features = keembay_pcie_get_features,
+};
+
+static const struct dw_pcie_host_ops keembay_pcie_host_ops = {
+};
+
+static int keembay_pcie_add_pcie_port(struct keembay_pcie *pcie,
+ struct platform_device *pdev)
+{
+ struct dw_pcie *pci = &pcie->pci;
+ struct pcie_port *pp = &pci->pp;
+ struct device *dev = &pdev->dev;
+ u32 val;
+ int ret;
+
+ pp->ops = &keembay_pcie_host_ops;
+ pp->msi_irq = -ENODEV;
+
+ ret = keembay_pcie_setup_msi_irq(pcie);
+ if (ret)
+ return ret;
+
+ pcie->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(pcie->reset))
+ return PTR_ERR(pcie->reset);
+
+ ret = keembay_pcie_probe_clocks(pcie);
+ if (ret)
+ return ret;
+
+ val = readl(pcie->apb_base + PCIE_REGS_PCIE_PHY_CNTL);
+ val |= PHY0_SRAM_BYPASS;
+ writel(val, pcie->apb_base + PCIE_REGS_PCIE_PHY_CNTL);
+
+ writel(PCIE_DEVICE_TYPE, pcie->apb_base + PCIE_REGS_PCIE_CFG);
+
+ ret = keembay_pcie_pll_init(pcie);
+ if (ret)
+ return ret;
+
+ val = readl(pcie->apb_base + PCIE_REGS_PCIE_CFG);
+ writel(val | PCIE_RSTN, pcie->apb_base + PCIE_REGS_PCIE_CFG);
+ keembay_ep_reset_deassert(pcie);
+
+ ret = dw_pcie_host_init(pp);
+ if (ret) {
+ keembay_ep_reset_assert(pcie);
+ dev_err(dev, "Failed to initialize host: %d\n", ret);
+ return ret;
+ }
+
+ val = readl(pcie->apb_base + PCIE_REGS_INTERRUPT_ENABLE);
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ val |= MSI_CTRL_INT_EN;
+ writel(val, pcie->apb_base + PCIE_REGS_INTERRUPT_ENABLE);
+
+ return 0;
+}
+
+static int keembay_pcie_probe(struct platform_device *pdev)
+{
+ const struct keembay_pcie_of_data *data;
+ struct device *dev = &pdev->dev;
+ struct keembay_pcie *pcie;
+ struct dw_pcie *pci;
+ enum dw_pcie_device_mode mode;
+
+ data = device_get_match_data(dev);
+ if (!data)
+ return -ENODEV;
+
+ mode = (enum dw_pcie_device_mode)data->mode;
+
+ pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+ if (!pcie)
+ return -ENOMEM;
+
+ pci = &pcie->pci;
+ pci->dev = dev;
+ pci->ops = &keembay_pcie_ops;
+
+ pcie->mode = mode;
+
+ pcie->apb_base = devm_platform_ioremap_resource_byname(pdev, "apb");
+ if (IS_ERR(pcie->apb_base))
+ return PTR_ERR(pcie->apb_base);
+
+ platform_set_drvdata(pdev, pcie);
+
+ switch (pcie->mode) {
+ case DW_PCIE_RC_TYPE:
+ if (!IS_ENABLED(CONFIG_PCIE_KEEMBAY_HOST))
+ return -ENODEV;
+
+ return keembay_pcie_add_pcie_port(pcie, pdev);
+ case DW_PCIE_EP_TYPE:
+ if (!IS_ENABLED(CONFIG_PCIE_KEEMBAY_EP))
+ return -ENODEV;
+
+ pci->ep.ops = &keembay_pcie_ep_ops;
+ return dw_pcie_ep_init(&pci->ep);
+ default:
+ dev_err(dev, "Invalid device type %d\n", pcie->mode);
+ return -ENODEV;
+ }
+}
+
+static const struct keembay_pcie_of_data keembay_pcie_rc_of_data = {
+ .mode = DW_PCIE_RC_TYPE,
+};
+
+static const struct keembay_pcie_of_data keembay_pcie_ep_of_data = {
+ .mode = DW_PCIE_EP_TYPE,
+};
+
+static const struct of_device_id keembay_pcie_of_match[] = {
+ {
+ .compatible = "intel,keembay-pcie",
+ .data = &keembay_pcie_rc_of_data,
+ },
+ {
+ .compatible = "intel,keembay-pcie-ep",
+ .data = &keembay_pcie_ep_of_data,
+ },
+ {}
+};
+
+static struct platform_driver keembay_pcie_driver = {
+ .driver = {
+ .name = "keembay-pcie",
+ .of_match_table = keembay_pcie_of_match,
+ .suppress_bind_attrs = true,
+ },
+ .probe = keembay_pcie_probe,
+};
+builtin_platform_driver(keembay_pcie_driver);