diff mbox series

[v14,2/5] dt-bindings: pinctrl: mt8195: change pull up/down description

Message ID 20210924080632.28410-3-zhiyong.tao@mediatek.com (mailing list archive)
State New, archived
Headers show
Series Mediatek pinctrl patch on mt8195 | expand

Commit Message

zhiyong.tao Sept. 24, 2021, 8:06 a.m. UTC
For supporting SI units in "bias-pull-down" & "bias-pull-up",
change pull up/down description
and add "mediatek,rsel_resistance_in_si_unit" description.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
---
 .../bindings/pinctrl/pinctrl-mt8195.yaml      | 86 ++++++++++++++++++-
 1 file changed, 84 insertions(+), 2 deletions(-)

Comments

Rob Herring (Arm) Sept. 29, 2021, 9:47 p.m. UTC | #1
On Fri, Sep 24, 2021 at 04:06:29PM +0800, Zhiyong Tao wrote:
> For supporting SI units in "bias-pull-down" & "bias-pull-up",
> change pull up/down description
> and add "mediatek,rsel_resistance_in_si_unit" description.
> 
> Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
> ---
>  .../bindings/pinctrl/pinctrl-mt8195.yaml      | 86 ++++++++++++++++++-
>  1 file changed, 84 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> index 2f12ec59eee5..5f642bef72af 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> @@ -49,6 +49,12 @@ properties:
>      description: The interrupt outputs to sysirq.
>      maxItems: 1
>  
> +  mediatek,rsel_resistance_in_si_unit:

s/_/-/

> +    type: boolean
> +    description: |
> +      Identifying i2c pins pull up/down type which is RSEL. It can support
> +      RSEL define or si unit value(ohm) to set different resistance.

Aren't the RSEL and ohms disjoint values? 0-207 for RSEL and >1000 for 
ohms. Why is this property even needed.

> +
>  #PIN CONFIGURATION NODES
>  patternProperties:
>    '-pins$':
> @@ -85,9 +91,85 @@ patternProperties:
>            2/4/6/8/10/12/14/16mA in mt8195.
>          enum: [0, 1, 2, 3, 4, 5, 6, 7]
>  
> -      bias-pull-down: true
> +      bias-pull-down:
> +        description: |
> +          For pull down type is normal, it don't need add RSEL & R1R0 define
> +          and resistance value.
> +          For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
> +          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> +          define in mt8195.
> +          For pull down type is RSEL, it can add RSEL define & resistance value(ohm)
> +          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> +          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +          define in mt8195. It can also support resistance value(ohm) "75000" & "5000" in mt8195.
> +          oneOf:

Because of the indentation, this is all just part of 'description'.

> +            - enum: [100, 101, 102, 103]
> +            - description: mt8195 pull down PUPD/R0/R1 type define value.

This entry is always true.

> +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]

Are these supposed to be hex?

> +            - description: mt8195 pull down RSEL type define value.

And so is this one. That makes 'oneOf' always false.

> +            - enum: [75000, 5000]
> +            - description: mt8195 pull down RSEL type si unit value(ohm).
> +
> +          An example of using RSEL define:
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-down = <MTK_PULL_SET_RSEL_001>;
> +            };
> +          };
> +          An example of using si unit resistance value(ohm):
> +          &pio {
> +            mediatek,rsel_resistance_in_si_unit;
> +          }
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-down = <75000>;
> +            };
> +          };
>  
> -      bias-pull-up: true
> +      bias-pull-up:
> +        description: |
> +          For pull up type is normal, it don't need add RSEL & R1R0 define
> +          and resistance value.
> +          For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
> +          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> +          define in mt8195.
> +          For pull up type is RSEL, it can add RSEL define & resistance value(ohm)
> +          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> +          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +          define in mt8195. It can also support resistance value(ohm)
> +          "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8195.
> +          oneOf:
> +            - enum: [100, 101, 102, 103]
> +            - description: mt8195 pull up PUPD/R0/R1 type define value.
> +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> +            - description: mt8195 pull up RSEL type define value.
> +            - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
> +            - description: mt8195 pull up RSEL type si unit value(ohm).

Same issues here.

> +          An example of using RSEL define:
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> +            };
> +          };
> +          An example of using si unit resistance value(ohm):
> +          &pio {
> +            mediatek,rsel_resistance_in_si_unit;
> +          }
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-up = <1000>;
> +            };
> +          };
>  
>        bias-disable: true
>  
> -- 
> 2.25.1
> 
>
zhiyong.tao Sept. 30, 2021, 1:54 a.m. UTC | #2
On Wed, 2021-09-29 at 16:47 -0500, Rob Herring wrote:
> On Fri, Sep 24, 2021 at 04:06:29PM +0800, Zhiyong Tao wrote:
> > For supporting SI units in "bias-pull-down" & "bias-pull-up",
> > change pull up/down description
> > and add "mediatek,rsel_resistance_in_si_unit" description.
> > 
> > Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
> > ---
> >  .../bindings/pinctrl/pinctrl-mt8195.yaml      | 86
> > ++++++++++++++++++-
> >  1 file changed, 84 insertions(+), 2 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-
> > mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-
> > mt8195.yaml
> > index 2f12ec59eee5..5f642bef72af 100644
> > --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> > @@ -49,6 +49,12 @@ properties:
> >      description: The interrupt outputs to sysirq.
> >      maxItems: 1
> >  
> > +  mediatek,rsel_resistance_in_si_unit:
> 
> s/_/-/

Hi Rob,

what do you mean?

> 
> > +    type: boolean
> > +    description: |
> > +      Identifying i2c pins pull up/down type which is RSEL. It can
> > support
> > +      RSEL define or si unit value(ohm) to set different
> > resistance.
> 
> Aren't the RSEL and ohms disjoint values? 0-207 for RSEL and >1000
> for 
> ohms. Why is this property even needed.
> 
No, they aren't.
As we talked in v11. "mediatek,rsel_resistance_in_si_unit" is only a
flag.



Hi ChenYu,

In the next version, we provide a solution which we discussed internal
to avoid value clashes.
 
The solution:
1. We will keep the define "MTK_PULL_SET_RSEL_000 200". It won't
change.

2. We will add a property in pio dtsi node, for example,
the property name is "rsel_resistance_in_si_unit".
We will add a flag "rsel_si_unit" in pinctrl device.
in probe function, we will identify the property name
"rsel_resistance_in_si_unit" to set the flag "rsel_si_unit" value.
So it can void value clashes.

3.We will provide the define "MTK_PULL_SET_RSEL_000 200" and si unit
two solution. users can support which solution by add property
"rsel_resistance_in_si_unit" in dts node or not.

Thanks

> > +
> >  #PIN CONFIGURATION NODES
> >  patternProperties:
> >    '-pins$':
> > @@ -85,9 +91,85 @@ patternProperties:
> >            2/4/6/8/10/12/14/16mA in mt8195.
> >          enum: [0, 1, 2, 3, 4, 5, 6, 7]
> >  
> > -      bias-pull-down: true
> > +      bias-pull-down:
> > +        description: |
> > +          For pull down type is normal, it don't need add RSEL &
> > R1R0 define
> > +          and resistance value.
> > +          For pull down type is PUPD/R0/R1 type, it can add R1R0
> > define to
> > +          set different resistance. It can support
> > "MTK_PUPD_SET_R1R0_00" &
> > +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> > "MTK_PUPD_SET_R1R0_11"
> > +          define in mt8195.
> > +          For pull down type is RSEL, it can add RSEL define &
> > resistance value(ohm)
> > +          to set different resistance by identifying property
> > "mediatek,rsel_resistance_in_si_unit".
> > +          It can support "MTK_PULL_SET_RSEL_000" &
> > "MTK_PULL_SET_RSEL_001"
> > +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" &
> > "MTK_PULL_SET_RSEL_100"
> > +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" &
> > "MTK_PULL_SET_RSEL_111"
> > +          define in mt8195. It can also support resistance
> > value(ohm) "75000" & "5000" in mt8195.
> > +          oneOf:
> 
> Because of the indentation, this is all just part of 'description'.

Can you help to give some suggestion to fix it?


> 
> > +            - enum: [100, 101, 102, 103]
> > +            - description: mt8195 pull down PUPD/R0/R1 type define
> > value.
> 
> This entry is always true.

why is it always true? we only get define value.
"100~104" are means that "#define MTK_PUPD_SET_R1R0_10 102" in
include/dt-bindings/pinctrl/mt65xx.h.

> 
> > +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> 
> Are these supposed to be hex?
yes, it is patch 1/5 define "#define MTK_PULL_SET_RSEL_000  200".
> 
> > +            - description: mt8195 pull down RSEL type define
> > value.
> 
> And so is this one. That makes 'oneOf' always false.

why is it always false? we only get the si unit value.

> 
> > +            - enum: [75000, 5000]
> > +            - description: mt8195 pull down RSEL type si unit
> > value(ohm).
> > +
> > +          An example of using RSEL define:
> > +          pincontroller {
> > +            i2c0_pin {
> > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > +              bias-pull-down = <MTK_PULL_SET_RSEL_001>;
> > +            };
> > +          };
> > +          An example of using si unit resistance value(ohm):
> > +          &pio {
> > +            mediatek,rsel_resistance_in_si_unit;
> > +          }
> > +          pincontroller {
> > +            i2c0_pin {
> > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > +              bias-pull-down = <75000>;
> > +            };
> > +          };
> >  
> > -      bias-pull-up: true
> > +      bias-pull-up:
> > +        description: |
> > +          For pull up type is normal, it don't need add RSEL &
> > R1R0 define
> > +          and resistance value.
> > +          For pull up type is PUPD/R0/R1 type, it can add R1R0
> > define to
> > +          set different resistance. It can support
> > "MTK_PUPD_SET_R1R0_00" &
> > +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> > "MTK_PUPD_SET_R1R0_11"
> > +          define in mt8195.
> > +          For pull up type is RSEL, it can add RSEL define &
> > resistance value(ohm)
> > +          to set different resistance by identifying property
> > "mediatek,rsel_resistance_in_si_unit".
> > +          It can support "MTK_PULL_SET_RSEL_000" &
> > "MTK_PULL_SET_RSEL_001"
> > +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" &
> > "MTK_PULL_SET_RSEL_100"
> > +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" &
> > "MTK_PULL_SET_RSEL_111"
> > +          define in mt8195. It can also support resistance
> > value(ohm)
> > +          "1000" & "1500" & "2000" & "3000" & "4000" & "5000" &
> > "10000" & "75000" in mt8195.
> > +          oneOf:
> > +            - enum: [100, 101, 102, 103]
> > +            - description: mt8195 pull up PUPD/R0/R1 type define
> > value.
> > +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> > +            - description: mt8195 pull up RSEL type define value.
> > +            - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000,
> > 75000]
> > +            - description: mt8195 pull up RSEL type si unit
> > value(ohm).
> 
> Same issues here.
> 
> > +          An example of using RSEL define:
> > +          pincontroller {
> > +            i2c0_pin {
> > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > +              bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> > +            };
> > +          };
> > +          An example of using si unit resistance value(ohm):
> > +          &pio {
> > +            mediatek,rsel_resistance_in_si_unit;
> > +          }
> > +          pincontroller {
> > +            i2c0_pin {
> > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > +              bias-pull-up = <1000>;
> > +            };
> > +          };
> >  
> >        bias-disable: true
> >  
> > -- 
> > 2.25.1
> > 
> >
Linus Walleij Sept. 30, 2021, 3:38 p.m. UTC | #3
On Thu, Sep 30, 2021 at 3:54 AM zhiyong.tao <zhiyong.tao@mediatek.com> wrote:

> > > +  mediatek,rsel_resistance_in_si_unit:
> >
> > s/_/-/
>
> Hi Rob,
>
> what do you mean?

It's a search/replace syntax used in sed (stream editor) meaning
"replace _ with -" i.e.
mediatek,rsel-resistance-in-si-unit

Yours,
Linus Walleij
Linus Walleij Sept. 30, 2021, 3:41 p.m. UTC | #4
Hi Rob,

how do you want me to act with this patch set, as it is already
merged and I was pretty happy since it is a v14 and feeling
it was getting a bit over-reviewed....

Are the binding problems solvable in incremental patches
or do you think I should pull out the patch series?

Yours,
Linus Walleij
Chen-Yu Tsai Oct. 13, 2021, 6:49 a.m. UTC | #5
On Thu, Sep 30, 2021 at 9:59 AM zhiyong.tao <zhiyong.tao@mediatek.com> wrote:
>
> On Wed, 2021-09-29 at 16:47 -0500, Rob Herring wrote:
> > On Fri, Sep 24, 2021 at 04:06:29PM +0800, Zhiyong Tao wrote:
> > > For supporting SI units in "bias-pull-down" & "bias-pull-up",
> > > change pull up/down description
> > > and add "mediatek,rsel_resistance_in_si_unit" description.
> > >
> > > Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
> > > ---
> > >  .../bindings/pinctrl/pinctrl-mt8195.yaml      | 86
> > > ++++++++++++++++++-
> > >  1 file changed, 84 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-
> > > mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-
> > > mt8195.yaml
> > > index 2f12ec59eee5..5f642bef72af 100644
> > > --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> > > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> > > @@ -49,6 +49,12 @@ properties:
> > >      description: The interrupt outputs to sysirq.
> > >      maxItems: 1
> > >
> > > +  mediatek,rsel_resistance_in_si_unit:
> >
> > s/_/-/
>
> Hi Rob,
>
> what do you mean?

He means: replace the hyphens ("-") with underscores ("_").
(s/X/Y/ is a regular expression.)

> >
> > > +    type: boolean
> > > +    description: |
> > > +      Identifying i2c pins pull up/down type which is RSEL. It can
> > > support
> > > +      RSEL define or si unit value(ohm) to set different
> > > resistance.
> >
> > Aren't the RSEL and ohms disjoint values? 0-207 for RSEL and >1000
> > for
> > ohms. Why is this property even needed.
> >
> No, they aren't.
> As we talked in v11. "mediatek,rsel_resistance_in_si_unit" is only a
> flag.
>
>
>
> Hi ChenYu,
>
> In the next version, we provide a solution which we discussed internal
> to avoid value clashes.
>
> The solution:
> 1. We will keep the define "MTK_PULL_SET_RSEL_000 200". It won't
> change.
>
> 2. We will add a property in pio dtsi node, for example,
> the property name is "rsel_resistance_in_si_unit".
> We will add a flag "rsel_si_unit" in pinctrl device.
> in probe function, we will identify the property name
> "rsel_resistance_in_si_unit" to set the flag "rsel_si_unit" value.
> So it can void value clashes.
>
> 3.We will provide the define "MTK_PULL_SET_RSEL_000 200" and si unit
> two solution. users can support which solution by add property
> "rsel_resistance_in_si_unit" in dts node or not.

Right. I thought that is what is implemented in this version already?

Also I just realized that this binding is limited in scope to just the
MT8195, for which we already know that the RSEL values do not overlap
with MTK_PULL_SET_RSEL_*. I assume that is why Rob thinks the flag
is unnecessary.

> > > +
> > >  #PIN CONFIGURATION NODES
> > >  patternProperties:
> > >    '-pins$':
> > > @@ -85,9 +91,85 @@ patternProperties:
> > >            2/4/6/8/10/12/14/16mA in mt8195.
> > >          enum: [0, 1, 2, 3, 4, 5, 6, 7]
> > >
> > > -      bias-pull-down: true
> > > +      bias-pull-down:
> > > +        description: |
> > > +          For pull down type is normal, it don't need add RSEL &
> > > R1R0 define
> > > +          and resistance value.
> > > +          For pull down type is PUPD/R0/R1 type, it can add R1R0
> > > define to
> > > +          set different resistance. It can support
> > > "MTK_PUPD_SET_R1R0_00" &
> > > +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> > > "MTK_PUPD_SET_R1R0_11"
> > > +          define in mt8195.
> > > +          For pull down type is RSEL, it can add RSEL define &
> > > resistance value(ohm)
> > > +          to set different resistance by identifying property
> > > "mediatek,rsel_resistance_in_si_unit".
> > > +          It can support "MTK_PULL_SET_RSEL_000" &
> > > "MTK_PULL_SET_RSEL_001"
> > > +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" &
> > > "MTK_PULL_SET_RSEL_100"
> > > +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" &
> > > "MTK_PULL_SET_RSEL_111"
> > > +          define in mt8195. It can also support resistance
> > > value(ohm) "75000" & "5000" in mt8195.
> > > +          oneOf:
> >
> > Because of the indentation, this is all just part of 'description'.
>
> Can you help to give some suggestion to fix it?

Unindent it by two spaces, so that it is at the same level with
"description:".

> > > +            - enum: [100, 101, 102, 103]
> > > +            - description: mt8195 pull down PUPD/R0/R1 type define
> > > value.
> >
> > This entry is always true.
>
> why is it always true? we only get define value.
> "100~104" are means that "#define MTK_PUPD_SET_R1R0_10 102" in
> include/dt-bindings/pinctrl/mt65xx.h.

"description" is not a conditional match, so it always evaluates to true.
Based on my limited DT schema and YAML knowledge, I think the underlying
issue is that you have the structure incorrectly defined.

"-" denotes a list item. So in your example, you have "enum" and "description"
as separate associative arrays, each as a list item part of the "oneOf" list.

What you want is actually:

    oneOf:
      - enum: [100, 101, 102, 103]
        description: mt8195 pull down PUPD/R0/R1 type define value.
      - enum: [200, 201, 202, 203, 204, 205, 206, 207]
        description: mt8195 pull down RSEL type define value.

So that "enum" and "description" are part of the same associative array.
Note the lack of a "-" and the extra indentation in front of "description".


Regards
ChenYu


> >
> > > +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> >
> > Are these supposed to be hex?
> yes, it is patch 1/5 define "#define MTK_PULL_SET_RSEL_000  200".
> >
> > > +            - description: mt8195 pull down RSEL type define
> > > value.
> >
> > And so is this one. That makes 'oneOf' always false.
>
> why is it always false? we only get the si unit value.
>
> >
> > > +            - enum: [75000, 5000]
> > > +            - description: mt8195 pull down RSEL type si unit
> > > value(ohm).
> > > +
> > > +          An example of using RSEL define:
> > > +          pincontroller {
> > > +            i2c0_pin {
> > > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > > +              bias-pull-down = <MTK_PULL_SET_RSEL_001>;
> > > +            };
> > > +          };
> > > +          An example of using si unit resistance value(ohm):
> > > +          &pio {
> > > +            mediatek,rsel_resistance_in_si_unit;
> > > +          }
> > > +          pincontroller {
> > > +            i2c0_pin {
> > > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > > +              bias-pull-down = <75000>;
> > > +            };
> > > +          };
> > >
> > > -      bias-pull-up: true
> > > +      bias-pull-up:
> > > +        description: |
> > > +          For pull up type is normal, it don't need add RSEL &
> > > R1R0 define
> > > +          and resistance value.
> > > +          For pull up type is PUPD/R0/R1 type, it can add R1R0
> > > define to
> > > +          set different resistance. It can support
> > > "MTK_PUPD_SET_R1R0_00" &
> > > +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> > > "MTK_PUPD_SET_R1R0_11"
> > > +          define in mt8195.
> > > +          For pull up type is RSEL, it can add RSEL define &
> > > resistance value(ohm)
> > > +          to set different resistance by identifying property
> > > "mediatek,rsel_resistance_in_si_unit".
> > > +          It can support "MTK_PULL_SET_RSEL_000" &
> > > "MTK_PULL_SET_RSEL_001"
> > > +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" &
> > > "MTK_PULL_SET_RSEL_100"
> > > +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" &
> > > "MTK_PULL_SET_RSEL_111"
> > > +          define in mt8195. It can also support resistance
> > > value(ohm)
> > > +          "1000" & "1500" & "2000" & "3000" & "4000" & "5000" &
> > > "10000" & "75000" in mt8195.
> > > +          oneOf:
> > > +            - enum: [100, 101, 102, 103]
> > > +            - description: mt8195 pull up PUPD/R0/R1 type define
> > > value.
> > > +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> > > +            - description: mt8195 pull up RSEL type define value.
> > > +            - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000,
> > > 75000]
> > > +            - description: mt8195 pull up RSEL type si unit
> > > value(ohm).
> >
> > Same issues here.
> >
> > > +          An example of using RSEL define:
> > > +          pincontroller {
> > > +            i2c0_pin {
> > > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > > +              bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> > > +            };
> > > +          };
> > > +          An example of using si unit resistance value(ohm):
> > > +          &pio {
> > > +            mediatek,rsel_resistance_in_si_unit;
> > > +          }
> > > +          pincontroller {
> > > +            i2c0_pin {
> > > +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> > > +              bias-pull-up = <1000>;
> > > +            };
> > > +          };
> > >
> > >        bias-disable: true
> > >
> > > --
> > > 2.25.1
> > >
> > >
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
index 2f12ec59eee5..5f642bef72af 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
@@ -49,6 +49,12 @@  properties:
     description: The interrupt outputs to sysirq.
     maxItems: 1
 
+  mediatek,rsel_resistance_in_si_unit:
+    type: boolean
+    description: |
+      Identifying i2c pins pull up/down type which is RSEL. It can support
+      RSEL define or si unit value(ohm) to set different resistance.
+
 #PIN CONFIGURATION NODES
 patternProperties:
   '-pins$':
@@ -85,9 +91,85 @@  patternProperties:
           2/4/6/8/10/12/14/16mA in mt8195.
         enum: [0, 1, 2, 3, 4, 5, 6, 7]
 
-      bias-pull-down: true
+      bias-pull-down:
+        description: |
+          For pull down type is normal, it don't need add RSEL & R1R0 define
+          and resistance value.
+          For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
+          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
+          define in mt8195.
+          For pull down type is RSEL, it can add RSEL define & resistance value(ohm)
+          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
+          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
+          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+          define in mt8195. It can also support resistance value(ohm) "75000" & "5000" in mt8195.
+          oneOf:
+            - enum: [100, 101, 102, 103]
+            - description: mt8195 pull down PUPD/R0/R1 type define value.
+            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+            - description: mt8195 pull down RSEL type define value.
+            - enum: [75000, 5000]
+            - description: mt8195 pull down RSEL type si unit value(ohm).
+
+          An example of using RSEL define:
+          pincontroller {
+            i2c0_pin {
+              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+              bias-pull-down = <MTK_PULL_SET_RSEL_001>;
+            };
+          };
+          An example of using si unit resistance value(ohm):
+          &pio {
+            mediatek,rsel_resistance_in_si_unit;
+          }
+          pincontroller {
+            i2c0_pin {
+              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+              bias-pull-down = <75000>;
+            };
+          };
 
-      bias-pull-up: true
+      bias-pull-up:
+        description: |
+          For pull up type is normal, it don't need add RSEL & R1R0 define
+          and resistance value.
+          For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
+          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
+          define in mt8195.
+          For pull up type is RSEL, it can add RSEL define & resistance value(ohm)
+          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
+          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
+          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+          define in mt8195. It can also support resistance value(ohm)
+          "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8195.
+          oneOf:
+            - enum: [100, 101, 102, 103]
+            - description: mt8195 pull up PUPD/R0/R1 type define value.
+            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+            - description: mt8195 pull up RSEL type define value.
+            - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
+            - description: mt8195 pull up RSEL type si unit value(ohm).
+          An example of using RSEL define:
+          pincontroller {
+            i2c0_pin {
+              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+              bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+            };
+          };
+          An example of using si unit resistance value(ohm):
+          &pio {
+            mediatek,rsel_resistance_in_si_unit;
+          }
+          pincontroller {
+            i2c0_pin {
+              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+              bias-pull-up = <1000>;
+            };
+          };
 
       bias-disable: true