diff mbox series

[v2,2/2] ath11k: enable 802.11 power save mode in station mode

Message ID 20211108123826.8463-2-kvalo@codeaurora.org (mailing list archive)
State Accepted
Commit b2beffa7d9a67b59b085616a27f1d10b1e80784f
Delegated to: Kalle Valo
Headers show
Series [v2,1/2] ath11k: convert ath11k_wmi_pdev_set_ps_mode() to use enum wmi_sta_ps_mode | expand

Commit Message

Kalle Valo Nov. 8, 2021, 12:38 p.m. UTC
From: Carl Huang <cjhuang@codeaurora.org>

To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.

Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.

To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---

v2:

* improve commit log

* use existing ath11k_wmi_pdev_set_ps_mode()

* rename protocol_ps to supports_sta_ps

* cosmetic changes

 drivers/net/wireless/ath/ath11k/core.c |  5 ++
 drivers/net/wireless/ath/ath11k/core.h |  1 +
 drivers/net/wireless/ath/ath11k/hw.h   |  1 +
 drivers/net/wireless/ath/ath11k/mac.c  | 87 ++++++++++++++++++++++++++
 4 files changed, 94 insertions(+)

Comments

Mark Herbert Nov. 10, 2021, 6:16 p.m. UTC | #1
Running the new patch version, looks good so far.

CPU reaches PC10, and in idle can be about 80% in PC10 which is perfect.

With the firmware 01740 which is the release firmware for linux 
everyting good until I try to reload module ath11k_pci.

With the downgraded firmware  01230 the card is crashing periodically 
but 01230 allows to do rmmod/modprobe ath11k sequence and happily 
recovers, and the PC10 state residency is also good.

The firmware hacked from Dell official Windows drivers ( fw_version 
0x10110341 fw_build_timestamp 2021-05-02 15:16 fw_build_id in dmesg) is 
somewhere in the middle. No crashes until modules reloaded, but on 
reload the chances are 50/50 if the card will come back or not. PC10 
residency is also perfect.

On 08.11.2021 15:38, Kalle Valo wrote:
> From: Carl Huang <cjhuang@codeaurora.org>
>
> To reduce power consumption enable 802.11 power save mode in station mode. This
> allows both radio and CPU to sleep more.
>
> Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
> families support this feature.
>
> To test that power save mode is running run "iw dev wls1 set power_save off",
> check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
> on" and check there is a NULL Data frame in sniffer.
>
> Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
>
> Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
> ---
>
> v2:
>
> * improve commit log
>
> * use existing ath11k_wmi_pdev_set_ps_mode()
>
> * rename protocol_ps to supports_sta_ps
>
> * cosmetic changes
>
>   drivers/net/wireless/ath/ath11k/core.c |  5 ++
>   drivers/net/wireless/ath/ath11k/core.h |  1 +
>   drivers/net/wireless/ath/ath11k/hw.h   |  1 +
>   drivers/net/wireless/ath/ath11k/mac.c  | 87 ++++++++++++++++++++++++++
>   4 files changed, 94 insertions(+)
>
> diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
> index b5a2af3ffc3e..a6c0d5ad7f9b 100644
> --- a/drivers/net/wireless/ath/ath11k/core.c
> +++ b/drivers/net/wireless/ath/ath11k/core.c
> @@ -76,6 +76,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>   		.supports_monitor = true,
>   		.supports_shadow_regs = false,
>   		.idle_ps = false,
> +		.supports_sta_ps = false,
>   		.cold_boot_calib = true,
>   		.supports_suspend = false,
>   		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
> @@ -125,6 +126,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>   		.supports_monitor = true,
>   		.supports_shadow_regs = false,
>   		.idle_ps = false,
> +		.supports_sta_ps = false,
>   		.cold_boot_calib = true,
>   		.supports_suspend = false,
>   		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
> @@ -173,6 +175,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>   		.supports_monitor = false,
>   		.supports_shadow_regs = true,
>   		.idle_ps = true,
> +		.supports_sta_ps = true,
>   		.cold_boot_calib = false,
>   		.supports_suspend = true,
>   		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
> @@ -221,6 +224,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>   		.supports_monitor = true,
>   		.supports_shadow_regs = false,
>   		.idle_ps = false,
> +		.supports_sta_ps = false,
>   		.cold_boot_calib = false,
>   		.supports_suspend = false,
>   		.hal_desc_sz = sizeof(struct hal_rx_desc_qcn9074),
> @@ -269,6 +273,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
>   		.supports_monitor = false,
>   		.supports_shadow_regs = true,
>   		.idle_ps = true,
> +		.supports_sta_ps = true,
>   		.cold_boot_calib = false,
>   		.supports_suspend = true,
>   		.hal_desc_sz = sizeof(struct hal_rx_desc_wcn6855),
> diff --git a/drivers/net/wireless/ath/ath11k/core.h b/drivers/net/wireless/ath/ath11k/core.h
> index 31d234a51c79..2f1e10b7cc17 100644
> --- a/drivers/net/wireless/ath/ath11k/core.h
> +++ b/drivers/net/wireless/ath/ath11k/core.h
> @@ -240,6 +240,7 @@ struct ath11k_vif {
>   	bool is_started;
>   	bool is_up;
>   	bool spectral_enabled;
> +	bool ps;
>   	u32 aid;
>   	u8 bssid[ETH_ALEN];
>   	struct cfg80211_bitrate_mask bitrate_mask;
> diff --git a/drivers/net/wireless/ath/ath11k/hw.h b/drivers/net/wireless/ath/ath11k/hw.h
> index 19223d36846e..1c298c24b617 100644
> --- a/drivers/net/wireless/ath/ath11k/hw.h
> +++ b/drivers/net/wireless/ath/ath11k/hw.h
> @@ -170,6 +170,7 @@ struct ath11k_hw_params {
>   	bool supports_monitor;
>   	bool supports_shadow_regs;
>   	bool idle_ps;
> +	bool supports_sta_ps;
>   	bool cold_boot_calib;
>   	bool supports_suspend;
>   	u32 hal_desc_sz;
> diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
> index f6511fc8ae8c..82fd44f34df2 100644
> --- a/drivers/net/wireless/ath/ath11k/mac.c
> +++ b/drivers/net/wireless/ath/ath11k/mac.c
> @@ -1049,6 +1049,83 @@ static int ath11k_mac_monitor_stop(struct ath11k *ar)
>   	return 0;
>   }
>   
> +static int ath11k_mac_vif_setup_ps(struct ath11k_vif *arvif)
> +{
> +	struct ath11k *ar = arvif->ar;
> +	struct ieee80211_vif *vif = arvif->vif;
> +	struct ieee80211_conf *conf = &ar->hw->conf;
> +	enum wmi_sta_powersave_param param;
> +	enum wmi_sta_ps_mode psmode;
> +	int ret;
> +	int timeout;
> +	bool enable_ps;
> +
> +	lockdep_assert_held(&arvif->ar->conf_mutex);
> +
> +	if (arvif->vif->type != NL80211_IFTYPE_STATION)
> +		return 0;
> +
> +	enable_ps = arvif->ps;
> +
> +	if (!arvif->is_started) {
> +		/* mac80211 can update vif powersave state while disconnected.
> +		 * Firmware doesn't behave nicely and consumes more power than
> +		 * necessary if PS is disabled on a non-started vdev. Hence
> +		 * force-enable PS for non-running vdevs.
> +		 */
> +		psmode = WMI_STA_PS_MODE_ENABLED;
> +	} else if (enable_ps) {
> +		psmode = WMI_STA_PS_MODE_ENABLED;
> +		param = WMI_STA_PS_PARAM_INACTIVITY_TIME;
> +
> +		timeout = conf->dynamic_ps_timeout;
> +		if (timeout == 0) {
> +			/* firmware doesn't like 0 */
> +			timeout = ieee80211_tu_to_usec(vif->bss_conf.beacon_int) / 1000;
> +		}
> +
> +		ret = ath11k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param,
> +						  timeout);
> +		if (ret) {
> +			ath11k_warn(ar->ab, "failed to set inactivity time for vdev %d: %i\n",
> +				    arvif->vdev_id, ret);
> +			return ret;
> +		}
> +	} else {
> +		psmode = WMI_STA_PS_MODE_DISABLED;
> +	}
> +
> +	ath11k_dbg(ar->ab, ATH11K_DBG_MAC, "mac vdev %d psmode %s\n",
> +		   arvif->vdev_id, psmode ? "enable" : "disable");
> +
> +	ret = ath11k_wmi_pdev_set_ps_mode(ar, arvif->vdev_id, psmode);
> +	if (ret) {
> +		ath11k_warn(ar->ab, "failed to set sta power save mode %d for vdev %d: %d\n",
> +			    psmode, arvif->vdev_id, ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int ath11k_mac_config_ps(struct ath11k *ar)
> +{
> +	struct ath11k_vif *arvif;
> +	int ret = 0;
> +
> +	lockdep_assert_held(&ar->conf_mutex);
> +
> +	list_for_each_entry(arvif, &ar->arvifs, list) {
> +		ret = ath11k_mac_vif_setup_ps(arvif);
> +		if (ret) {
> +			ath11k_warn(ar->ab, "failed to setup powersave: %d\n", ret);
> +			break;
> +		}
> +	}
> +
> +	return ret;
> +}
> +
>   static int ath11k_mac_op_config(struct ieee80211_hw *hw, u32 changed)
>   {
>   	struct ath11k *ar = hw->priv;
> @@ -2942,6 +3019,16 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
>   		ath11k_mac_txpower_recalc(ar);
>   	}
>   
> +	if (changed & BSS_CHANGED_PS &&
> +	    ar->ab->hw_params.supports_sta_ps) {
> +		arvif->ps = vif->bss_conf.ps;
> +
> +		ret = ath11k_mac_config_ps(ar);
> +		if (ret)
> +			ath11k_warn(ar->ab, "failed to setup ps on vdev %i: %d\n",
> +				    arvif->vdev_id, ret);
> +	}
> +
>   	if (changed & BSS_CHANGED_MCAST_RATE &&
>   	    !ath11k_mac_vif_chan(arvif->vif, &def)) {
>   		band = def.chan->band;
diff mbox series

Patch

diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
index b5a2af3ffc3e..a6c0d5ad7f9b 100644
--- a/drivers/net/wireless/ath/ath11k/core.c
+++ b/drivers/net/wireless/ath/ath11k/core.c
@@ -76,6 +76,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.supports_monitor = true,
 		.supports_shadow_regs = false,
 		.idle_ps = false,
+		.supports_sta_ps = false,
 		.cold_boot_calib = true,
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
@@ -125,6 +126,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.supports_monitor = true,
 		.supports_shadow_regs = false,
 		.idle_ps = false,
+		.supports_sta_ps = false,
 		.cold_boot_calib = true,
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
@@ -173,6 +175,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.supports_monitor = false,
 		.supports_shadow_regs = true,
 		.idle_ps = true,
+		.supports_sta_ps = true,
 		.cold_boot_calib = false,
 		.supports_suspend = true,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_ipq8074),
@@ -221,6 +224,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.supports_monitor = true,
 		.supports_shadow_regs = false,
 		.idle_ps = false,
+		.supports_sta_ps = false,
 		.cold_boot_calib = false,
 		.supports_suspend = false,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_qcn9074),
@@ -269,6 +273,7 @@  static const struct ath11k_hw_params ath11k_hw_params[] = {
 		.supports_monitor = false,
 		.supports_shadow_regs = true,
 		.idle_ps = true,
+		.supports_sta_ps = true,
 		.cold_boot_calib = false,
 		.supports_suspend = true,
 		.hal_desc_sz = sizeof(struct hal_rx_desc_wcn6855),
diff --git a/drivers/net/wireless/ath/ath11k/core.h b/drivers/net/wireless/ath/ath11k/core.h
index 31d234a51c79..2f1e10b7cc17 100644
--- a/drivers/net/wireless/ath/ath11k/core.h
+++ b/drivers/net/wireless/ath/ath11k/core.h
@@ -240,6 +240,7 @@  struct ath11k_vif {
 	bool is_started;
 	bool is_up;
 	bool spectral_enabled;
+	bool ps;
 	u32 aid;
 	u8 bssid[ETH_ALEN];
 	struct cfg80211_bitrate_mask bitrate_mask;
diff --git a/drivers/net/wireless/ath/ath11k/hw.h b/drivers/net/wireless/ath/ath11k/hw.h
index 19223d36846e..1c298c24b617 100644
--- a/drivers/net/wireless/ath/ath11k/hw.h
+++ b/drivers/net/wireless/ath/ath11k/hw.h
@@ -170,6 +170,7 @@  struct ath11k_hw_params {
 	bool supports_monitor;
 	bool supports_shadow_regs;
 	bool idle_ps;
+	bool supports_sta_ps;
 	bool cold_boot_calib;
 	bool supports_suspend;
 	u32 hal_desc_sz;
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index f6511fc8ae8c..82fd44f34df2 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -1049,6 +1049,83 @@  static int ath11k_mac_monitor_stop(struct ath11k *ar)
 	return 0;
 }
 
+static int ath11k_mac_vif_setup_ps(struct ath11k_vif *arvif)
+{
+	struct ath11k *ar = arvif->ar;
+	struct ieee80211_vif *vif = arvif->vif;
+	struct ieee80211_conf *conf = &ar->hw->conf;
+	enum wmi_sta_powersave_param param;
+	enum wmi_sta_ps_mode psmode;
+	int ret;
+	int timeout;
+	bool enable_ps;
+
+	lockdep_assert_held(&arvif->ar->conf_mutex);
+
+	if (arvif->vif->type != NL80211_IFTYPE_STATION)
+		return 0;
+
+	enable_ps = arvif->ps;
+
+	if (!arvif->is_started) {
+		/* mac80211 can update vif powersave state while disconnected.
+		 * Firmware doesn't behave nicely and consumes more power than
+		 * necessary if PS is disabled on a non-started vdev. Hence
+		 * force-enable PS for non-running vdevs.
+		 */
+		psmode = WMI_STA_PS_MODE_ENABLED;
+	} else if (enable_ps) {
+		psmode = WMI_STA_PS_MODE_ENABLED;
+		param = WMI_STA_PS_PARAM_INACTIVITY_TIME;
+
+		timeout = conf->dynamic_ps_timeout;
+		if (timeout == 0) {
+			/* firmware doesn't like 0 */
+			timeout = ieee80211_tu_to_usec(vif->bss_conf.beacon_int) / 1000;
+		}
+
+		ret = ath11k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param,
+						  timeout);
+		if (ret) {
+			ath11k_warn(ar->ab, "failed to set inactivity time for vdev %d: %i\n",
+				    arvif->vdev_id, ret);
+			return ret;
+		}
+	} else {
+		psmode = WMI_STA_PS_MODE_DISABLED;
+	}
+
+	ath11k_dbg(ar->ab, ATH11K_DBG_MAC, "mac vdev %d psmode %s\n",
+		   arvif->vdev_id, psmode ? "enable" : "disable");
+
+	ret = ath11k_wmi_pdev_set_ps_mode(ar, arvif->vdev_id, psmode);
+	if (ret) {
+		ath11k_warn(ar->ab, "failed to set sta power save mode %d for vdev %d: %d\n",
+			    psmode, arvif->vdev_id, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ath11k_mac_config_ps(struct ath11k *ar)
+{
+	struct ath11k_vif *arvif;
+	int ret = 0;
+
+	lockdep_assert_held(&ar->conf_mutex);
+
+	list_for_each_entry(arvif, &ar->arvifs, list) {
+		ret = ath11k_mac_vif_setup_ps(arvif);
+		if (ret) {
+			ath11k_warn(ar->ab, "failed to setup powersave: %d\n", ret);
+			break;
+		}
+	}
+
+	return ret;
+}
+
 static int ath11k_mac_op_config(struct ieee80211_hw *hw, u32 changed)
 {
 	struct ath11k *ar = hw->priv;
@@ -2942,6 +3019,16 @@  static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 		ath11k_mac_txpower_recalc(ar);
 	}
 
+	if (changed & BSS_CHANGED_PS &&
+	    ar->ab->hw_params.supports_sta_ps) {
+		arvif->ps = vif->bss_conf.ps;
+
+		ret = ath11k_mac_config_ps(ar);
+		if (ret)
+			ath11k_warn(ar->ab, "failed to setup ps on vdev %i: %d\n",
+				    arvif->vdev_id, ret);
+	}
+
 	if (changed & BSS_CHANGED_MCAST_RATE &&
 	    !ath11k_mac_vif_chan(arvif->vif, &def)) {
 		band = def.chan->band;