| Message ID | 20220428230933.15262-6-andre.przywara@arm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: sunxi: Initial Allwinner H616 SoC support | expand |
Dne petek, 29. april 2022 ob 01:09:32 CEST je Andre Przywara napisal(a): > The OrangePi Zero 2 is a development board with the new H616 SoC. It > comes with the following features: > - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU > - 512MiB/1GiB DDR3 DRAM > - AXP305 PMIC > - Raspberry-Pi-1 compatible GPIO header > - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports > - 1 USB 2.0 host port > - 1 USB 2.0 type C port (power supply + OTG) > - MicroSD slot > - on-board 2MiB bootable SPI NOR flash > - 1Gbps Ethernet port (via RTL8211F PHY) > - micro-HDMI port > - unsupported Allwinner WiFi/BT chip > > For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2 Please no external links. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-h616-orangepi-zero2.dts | 203 ++++++++++++++++++ > 2 files changed, 204 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- zero2.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/ allwinner/Makefile > index 8fa5c060a4fe..df2214e6d946 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/ arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > new file mode 100644 > index 000000000000..ca07cae698ce > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > @@ -0,0 +1,203 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2020 Arm Ltd. 2022? > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + model = "OrangePi Zero2"; > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; > + > + aliases { > + ethernet0 = &emac0; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-0 { > + function = LED_FUNCTION_POWER; > + color = <LED_COLOR_ID_RED>; > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ > + default-state = "on"; > + }; > + > + led-1 { > + function = LED_FUNCTION_STATUS; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ > + }; > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the USB-C socket */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > +}; > + > +&emac0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ext_rgmii_pins>; > + phy-mode = "rgmii"; > + phy-handle = <&ext_rgmii_phy>; > + phy-supply = <®_dcdce>; > + allwinner,rx-delay-ps = <3100>; > + allwinner,tx-delay-ps = <700>; > + status = "okay"; > +}; > + > +&mdio0 { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&r_rsb { > + status = "okay"; > + > + axp305: pmic@745 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + interrupt-controller; > + #interrupt-cells = <1>; > + reg = <0x745>; > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + reg_aldo2: aldo2 { /* 3.3V on headers */ > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + }; > + > + reg_aldo3: aldo3 { /* 3.3V on headers */ > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + bldo2 { > + /* unused */ > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + /* reserved */ > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; As discussed in the past, this will cause reboot issues because Linux will turn down above regulator and thus SD card will stop working. This should be always on. And please add pio regulators, this is something we always add later... Best regards, Jernej > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&spi0 { > + status = "okay"; > + > + flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <40000000>; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > -- > 2.35.3 > >
On Tue, 03 May 2022 21:41:21 +0200 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, > Dne petek, 29. april 2022 ob 01:09:32 CEST je Andre Przywara napisal(a): > > The OrangePi Zero 2 is a development board with the new H616 SoC. It > > comes with the following features: > > - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU > > - 512MiB/1GiB DDR3 DRAM > > - AXP305 PMIC > > - Raspberry-Pi-1 compatible GPIO header > > - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports > > - 1 USB 2.0 host port > > - 1 USB 2.0 type C port (power supply + OTG) > > - MicroSD slot > > - on-board 2MiB bootable SPI NOR flash > > - 1Gbps Ethernet port (via RTL8211F PHY) > > - micro-HDMI port > > - unsupported Allwinner WiFi/BT chip > > > > For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2 > > Please no external links. Shame. I understand the reasons behind that, but this source is rather stable (more so than some LKML archives ;-), and I copied the actual important information. But well, I guess people have to put it in their search engine and hope it doesn't drop them to the vendor's website ;-) > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > --- > > arch/arm64/boot/dts/allwinner/Makefile | 1 + > > .../allwinner/sun50i-h616-orangepi-zero2.dts | 203 ++++++++++++++++++ > > 2 files changed, 204 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- > zero2.dts > > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/ > allwinner/Makefile > > index 8fa5c060a4fe..df2214e6d946 100644 > > --- a/arch/arm64/boot/dts/allwinner/Makefile > > +++ b/arch/arm64/boot/dts/allwinner/Makefile > > @@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/ > arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > new file mode 100644 > > index 000000000000..ca07cae698ce > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > @@ -0,0 +1,203 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +/* > > + * Copyright (C) 2020 Arm Ltd. > > 2022? Mmh, but why? I wrote this in 2020, and it was published the first time that year[1]. If the copyright year means anything, by my understanding it should cover the earliest publication date, to establish the license conditions over every copy out there. [1] https://lore.kernel.org/linux-arm-kernel/20201202135409.13683-8-andre.przywara@arm.com/ > > > + */ > > + > > +/dts-v1/; > > + > > +#include "sun50i-h616.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/leds/common.h> > > + > > +/ { > > + model = "OrangePi Zero2"; > > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; > > + > > + aliases { > > + ethernet0 = &emac0; > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led-0 { > > + function = LED_FUNCTION_POWER; > > + color = <LED_COLOR_ID_RED>; > > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 > */ > > + default-state = "on"; > > + }; > > + > > + led-1 { > > + function = LED_FUNCTION_STATUS; > > + color = <LED_COLOR_ID_GREEN>; > > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 > */ > > + }; > > + }; > > + > > + reg_vcc5v: vcc5v { > > + /* board wide 5V supply directly from the USB-C socket > */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-5v"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + regulator-always-on; > > + }; > > +}; > > + > > +&emac0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ext_rgmii_pins>; > > + phy-mode = "rgmii"; > > + phy-handle = <&ext_rgmii_phy>; > > + phy-supply = <®_dcdce>; > > + allwinner,rx-delay-ps = <3100>; > > + allwinner,tx-delay-ps = <700>; > > + status = "okay"; > > +}; > > + > > +&mdio0 { > > + ext_rgmii_phy: ethernet-phy@1 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > +}; > > + > > +&mmc0 { > > + vmmc-supply = <®_dcdce>; > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > + bus-width = <4>; > > + status = "okay"; > > +}; > > + > > +&r_rsb { > > + status = "okay"; > > + > > + axp305: pmic@745 { > > + compatible = "x-powers,axp305", "x-powers,axp805", > > + "x-powers,axp806"; > > + interrupt-controller; > > + #interrupt-cells = <1>; > > + reg = <0x745>; > > + > > + x-powers,self-working-mode; > > + vina-supply = <®_vcc5v>; > > + vinb-supply = <®_vcc5v>; > > + vinc-supply = <®_vcc5v>; > > + vind-supply = <®_vcc5v>; > > + vine-supply = <®_vcc5v>; > > + aldoin-supply = <®_vcc5v>; > > + bldoin-supply = <®_vcc5v>; > > + cldoin-supply = <®_vcc5v>; > > + > > + regulators { > > + reg_aldo1: aldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = > <3300000>; > > + regulator-max-microvolt = > <3300000>; > > + regulator-name = "vcc-sys"; > > + }; > > + > > + reg_aldo2: aldo2 { /* 3.3V on headers > */ > > + regulator-always-on; > > + regulator-min-microvolt = > <3300000>; > > + regulator-max-microvolt = > <3300000>; > > + regulator-name = "vcc3v3-ext"; > > + }; > > + > > + reg_aldo3: aldo3 { /* 3.3V on headers > */ > > + regulator-always-on; > > + regulator-min-microvolt = > <3300000>; > > + regulator-max-microvolt = > <3300000>; > > + regulator-name = "vcc3v3-ext2"; > > + }; > > + > > + reg_bldo1: bldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = > <1800000>; > > + regulator-max-microvolt = > <1800000>; > > + regulator-name = "vcc1v8"; > > + }; > > + > > + bldo2 { > > + /* unused */ > > + }; > > + > > + bldo3 { > > + /* unused */ > > + }; > > + > > + bldo4 { > > + /* unused */ > > + }; > > + > > + cldo1 { > > + /* reserved */ > > + }; > > + > > + cldo2 { > > + /* unused */ > > + }; > > + > > + cldo3 { > > + /* unused */ > > + }; > > + > > + reg_dcdca: dcdca { > > + regulator-always-on; > > + regulator-min-microvolt = > <810000>; > > + regulator-max-microvolt = > <1080000>; > > + regulator-name = "vdd-cpu"; > > + }; > > + > > + reg_dcdcc: dcdcc { > > + regulator-always-on; > > + regulator-min-microvolt = > <810000>; > > + regulator-max-microvolt = > <1080000>; > > + regulator-name = "vdd-gpu-sys"; > > + }; > > + > > + reg_dcdcd: dcdcd { > > + regulator-always-on; > > + regulator-min-microvolt = > <1500000>; > > + regulator-max-microvolt = > <1500000>; > > + regulator-name = "vdd-dram"; > > + }; > > + > > + reg_dcdce: dcdce { > > + regulator-boot-on; > > As discussed in the past, this will cause reboot issues because Linux will > turn down above regulator and thus SD card will stop working. This should be > always on. > > And please add pio regulators, this is something we always add later... Sure, thanks for the heads up, will do. Cheers, Andre > > Best regards, > Jernej > > > + regulator-min-microvolt = > <3300000>; > > + regulator-max-microvolt = > <3300000>; > > + regulator-name = "vcc-eth-mmc"; > > + }; > > + > > + sw { > > + /* unused */ > > + }; > > + }; > > + }; > > +}; > > + > > +&spi0 { > > + status = "okay"; > > + > > + flash@0 { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + compatible = "jedec,spi-nor"; > > + reg = <0>; > > + spi-max-frequency = <40000000>; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_ph_pins>; > > + status = "okay"; > > +}; > > -- > > 2.35.3 > > > > > >
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 8fa5c060a4fe..df2214e6d946 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts new file mode 100644 index 000000000000..ca07cae698ce --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts @@ -0,0 +1,203 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2020 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "OrangePi Zero2"; + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; + + aliases { + ethernet0 = &emac0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_RED>; + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ + default-state = "on"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ + }; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the USB-C socket */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_dcdce>; + allwinner,rx-delay-ps = <3100>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&mdio0 { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + vmmc-supply = <®_dcdce>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp305: pmic@745 { + compatible = "x-powers,axp305", "x-powers,axp805", + "x-powers,axp806"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x745>; + + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-sys"; + }; + + reg_aldo2: aldo2 { /* 3.3V on headers */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext"; + }; + + reg_aldo3: aldo3 { /* 3.3V on headers */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext2"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + bldo2 { + /* unused */ + }; + + bldo3 { + /* unused */ + }; + + bldo4 { + /* unused */ + }; + + cldo1 { + /* reserved */ + }; + + cldo2 { + /* unused */ + }; + + cldo3 { + /* unused */ + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vdd-dram"; + }; + + reg_dcdce: dcdce { + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-eth-mmc"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +};
The OrangePi Zero 2 is a development board with the new H616 SoC. It comes with the following features: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 512MiB/1GiB DDR3 DRAM - AXP305 PMIC - Raspberry-Pi-1 compatible GPIO header - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports - 1 USB 2.0 host port - 1 USB 2.0 type C port (power supply + OTG) - MicroSD slot - on-board 2MiB bootable SPI NOR flash - 1Gbps Ethernet port (via RTL8211F PHY) - micro-HDMI port - unsupported Allwinner WiFi/BT chip For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2 Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../allwinner/sun50i-h616-orangepi-zero2.dts | 203 ++++++++++++++++++ 2 files changed, 204 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts