diff mbox series

[v4,2/3] dt-bindings: remoteproc: qcom: Convert SC7280 MSS bindings to YAML

Message ID 1652978825-5304-3-git-send-email-quic_sibis@quicinc.com (mailing list archive)
State Superseded
Headers show
Series Add support for proxy interconnect bandwidth votes | expand

Commit Message

Sibi Sankar May 19, 2022, 4:47 p.m. UTC
Convert SC7280 MSS PIL loading bindings to YAML.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
---

v4:
 * Remove older bindings [Matthias/Krzysztof]
 * Misc. Fixes [Krzysztof]
 * Rebased on v2 of Krzysztof's bindings cleanups

v3:
 * Re-ordered clock list, fixed pdc_sync typo [Rob/Matthias]

 .../devicetree/bindings/remoteproc/qcom,q6v5.txt   |  31 +--
 .../bindings/remoteproc/qcom,sc7280-mss-pil.yaml   | 250 +++++++++++++++++++++
 2 files changed, 252 insertions(+), 29 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml

Comments

Rob Herring (Arm) May 19, 2022, 7:23 p.m. UTC | #1
On Thu, 19 May 2022 22:17:04 +0530, Sibi Sankar wrote:
> Convert SC7280 MSS PIL loading bindings to YAML.
> 
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> ---
> 
> v4:
>  * Remove older bindings [Matthias/Krzysztof]
>  * Misc. Fixes [Krzysztof]
>  * Rebased on v2 of Krzysztof's bindings cleanups
> 
> v3:
>  * Re-ordered clock list, fixed pdc_sync typo [Rob/Matthias]
> 
>  .../devicetree/bindings/remoteproc/qcom,q6v5.txt   |  31 +--
>  .../bindings/remoteproc/qcom,sc7280-mss-pil.yaml   | 250 +++++++++++++++++++++
>  2 files changed, 252 insertions(+), 29 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
./Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml: Unable to find schema file matching $id: http://devicetree.org/schemas/remoteproc/qcom,glink-edge.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.example.dtb: remoteproc@4080000: glink-edge: False schema does not allow {'interrupts-extended': [[4294967295, 2, 0, 1]], 'mboxes': [[4294967295, 2, 0]], 'label': ['modem'], 'qcom,remote-pid': [[1]]}
	From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.
Stephen Boyd May 19, 2022, 10:35 p.m. UTC | #2
Quoting Sibi Sankar (2022-05-19 09:47:04)
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> new file mode 100644
> index 000000000000..a936d84eefa6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> @@ -0,0 +1,250 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-mss-pil.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm SC7280 MSS Peripheral Image Loader
> +
> +maintainers:
> +  - Sibi Sankar <quic_sibis@quicinc.com>
> +
> +description:
> +  This document describes the hardware for a component that loads and boots firmware
> +  on the Qualcomm Technology Inc. SC7280 Modem Hexagon Core.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,sc7280-mss-pil
> +
[..]
> +
> +  resets:
> +    items:
> +      - description: AOSS restart
> +      - description: PDC reset
> +
> +  reset-names:
> +    items:
> +      - const: mss_restart
> +      - const: pdc_reset
> +
> +  memory-region:
> +    maxItems: 2
> +    description: Phandle reference to the reserved-memory for the MBA region followed
> +                 by the modem region.
> +
> +  firmware-name:
> +    $ref: /schemas/types.yaml#/definitions/string-array
> +    maxItems: 2

Instead of maxItems can this be

       items:
         - description: Name of MBA firmware
	 - description: Name of modem firmware

so that we know the order? Same for 'memory-region' above.

> +    description:
> +      The name of the MBA and modem firmware to be loaded for this remote processor.
> +
> +  qcom,halt-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array

Should this have maxItems: 1? Or that's implicit from description?

> +    description:
> +      Phandle reference to a syscon representing TCSR followed by the
> +      four offsets within syscon for q6, modem, nc and vq6 halt registers.
> +
> +  qcom,ext-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array

Should this have min/maxItems: 2?

> +    description:
> +      Two phandle references to syscons representing TCSR_REG and TCSR register
> +      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
> +      and axim1_clk_off/crypto_clk_off registers respectively.
> +
> +  qcom,qaccept-regs:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    description:
> +      Phandle reference to a syscon representing TCSR followed by the
> +      three offsets within syscon for mdm, cx and axi qaccept registers.
> +
> +  qcom,qmp:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: Reference to the AOSS side-channel message RAM.
> +
> +  qcom,smem-states:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    description: States used by the AP to signal the Hexagon core
> +    items:
> +      - description: Stop the modem

This one did items for a phandle array so I think we should follow the
same above.

> +
> +  qcom,smem-state-names:
> +    description: The names of the state bits used for SMP2P output
> +    const: stop
> +
> +  glink-edge:
> +    $ref: qcom,glink-edge.yaml#
> +    description:
> +      Qualcomm G-Link subnode which represents communication edge, channels
> +      and devices related to the DSP.
[..]
> +        power-domain-names = "cx", "mss";
> +
> +        memory-region = <&mba_mem>, <&mpss_mem>;
> +
> +        qcom,qmp = <&aoss_qmp>;
> +
> +        qcom,smem-states = <&modem_smp2p_out 0>;
> +        qcom,smem-state-names = "stop";
> +
> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
> +        reset-names = "mss_restart", "pdc_reset";
> +
> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;

Because it's two items I'd expect:
	
	<&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;

> +        qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
> +
> +        glink-edge {
> +            interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
> +                                   IPCC_MPROC_SIGNAL_GLINK_QMP
> +                                   IRQ_TYPE_EDGE_RISING>;
Sibi Sankar May 20, 2022, 6:46 p.m. UTC | #3
Hey Stephen,

On 5/20/22 4:05 AM, Stephen Boyd wrote:
> Quoting Sibi Sankar (2022-05-19 09:47:04)
>> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
>> new file mode 100644
>> index 000000000000..a936d84eefa6
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
>> @@ -0,0 +1,250 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-mss-pil.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm SC7280 MSS Peripheral Image Loader
>> +
>> +maintainers:
>> +  - Sibi Sankar <quic_sibis@quicinc.com>
>> +
>> +description:
>> +  This document describes the hardware for a component that loads and boots firmware
>> +  on the Qualcomm Technology Inc. SC7280 Modem Hexagon Core.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - qcom,sc7280-mss-pil
>> +
> [..]
>> +
>> +  resets:
>> +    items:
>> +      - description: AOSS restart
>> +      - description: PDC reset
>> +
>> +  reset-names:
>> +    items:
>> +      - const: mss_restart
>> +      - const: pdc_reset
>> +
>> +  memory-region:
>> +    maxItems: 2
>> +    description: Phandle reference to the reserved-memory for the MBA region followed
>> +                 by the modem region.
>> +
>> +  firmware-name:
>> +    $ref: /schemas/types.yaml#/definitions/string-array
>> +    maxItems: 2
> 
> Instead of maxItems can this be
> 
>         items:
>           - description: Name of MBA firmware
> 	 - description: Name of modem firmware
> 
> so that we know the order? Same for 'memory-region' above.

ack

> 
>> +    description:
>> +      The name of the MBA and modem firmware to be loaded for this remote processor.
>> +
>> +  qcom,halt-regs:
>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> 
> Should this have maxItems: 1? Or that's implicit from description?

It's implicit!

> 
>> +    description:
>> +      Phandle reference to a syscon representing TCSR followed by the
>> +      four offsets within syscon for q6, modem, nc and vq6 halt registers.
>> +
>> +  qcom,ext-regs:
>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> 
> Should this have min/maxItems: 2?

ack

> 
>> +    description:
>> +      Two phandle references to syscons representing TCSR_REG and TCSR register
>> +      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
>> +      and axim1_clk_off/crypto_clk_off registers respectively.
>> +
>> +  qcom,qaccept-regs:
>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>> +    description:
>> +      Phandle reference to a syscon representing TCSR followed by the
>> +      three offsets within syscon for mdm, cx and axi qaccept registers.
>> +
>> +  qcom,qmp:
>> +    $ref: /schemas/types.yaml#/definitions/phandle
>> +    description: Reference to the AOSS side-channel message RAM.
>> +
>> +  qcom,smem-states:
>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>> +    description: States used by the AP to signal the Hexagon core
>> +    items:
>> +      - description: Stop the modem
> 
> This one did items for a phandle array so I think we should follow the
> same above.

ack

> 
>> +
>> +  qcom,smem-state-names:
>> +    description: The names of the state bits used for SMP2P output
>> +    const: stop
>> +
>> +  glink-edge:
>> +    $ref: qcom,glink-edge.yaml#
>> +    description:
>> +      Qualcomm G-Link subnode which represents communication edge, channels
>> +      and devices related to the DSP.
> [..]
>> +        power-domain-names = "cx", "mss";
>> +
>> +        memory-region = <&mba_mem>, <&mpss_mem>;
>> +
>> +        qcom,qmp = <&aoss_qmp>;
>> +
>> +        qcom,smem-states = <&modem_smp2p_out 0>;
>> +        qcom,smem-state-names = "stop";
>> +
>> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
>> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
>> +        reset-names = "mss_restart", "pdc_reset";
>> +
>> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
>> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
> 
> Because it's two items I'd expect:
> 	
> 	<&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;

I guess both the ways work since the driver uses
of_parse_phandle_with_fixed_args.

> 
>> +        qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
>> +
>> +        glink-edge {
>> +            interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
>> +                                   IPCC_MPROC_SIGNAL_GLINK_QMP
>> +                                   IRQ_TYPE_EDGE_RISING>;
Stephen Boyd May 20, 2022, 8:10 p.m. UTC | #4
Quoting Sibi Sankar (2022-05-20 11:46:58)
> On 5/20/22 4:05 AM, Stephen Boyd wrote:
> > Quoting Sibi Sankar (2022-05-19 09:47:04)
> >> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> >> new file mode 100644
> >> index 000000000000..a936d84eefa6
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
> >> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
> >> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
> >> +        reset-names = "mss_restart", "pdc_reset";
> >> +
> >> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
> >> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
> >
> > Because it's two items I'd expect:
> >
> >       <&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;
>
> I guess both the ways work since the driver uses
> of_parse_phandle_with_fixed_args.

See commit 39bd2b6a3783 ("dt-bindings: Improve phandle-array schemas")
for why the way you have it is not preferred.
Krzysztof Kozlowski May 21, 2022, 2:33 p.m. UTC | #5
On 20/05/2022 20:46, Sibi Sankar wrote:
>>> +  memory-region:
>>> +    maxItems: 2
>>> +    description: Phandle reference to the reserved-memory for the MBA region followed
>>> +                 by the modem region.
>>> +
>>> +  firmware-name:
>>> +    $ref: /schemas/types.yaml#/definitions/string-array
>>> +    maxItems: 2
>>
>> Instead of maxItems can this be
>>
>>         items:
>>           - description: Name of MBA firmware
>> 	 - description: Name of modem firmware
>>
>> so that we know the order? Same for 'memory-region' above.
> 
> ack
> 
>>
>>> +    description:
>>> +      The name of the MBA and modem firmware to be loaded for this remote processor.
>>> +
>>> +  qcom,halt-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>
>> Should this have maxItems: 1? Or that's implicit from description?
> 
> It's implicit!

I am not aware of such implicit rule in schema. maxItems are always
required. If this is maxItems:1 it is not even an array.

> 
>>
>>> +    description:
>>> +      Phandle reference to a syscon representing TCSR followed by the
>>> +      four offsets within syscon for q6, modem, nc and vq6 halt registers.
>>> +
>>> +  qcom,ext-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>
>> Should this have min/maxItems: 2?
> 
> ack

You should also define the items. This applies to all such fields. Check
the examples of syscon consumers.

> 
>>
>>> +    description:
>>> +      Two phandle references to syscons representing TCSR_REG and TCSR register
>>> +      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
>>> +      and axim1_clk_off/crypto_clk_off registers respectively.
>>> +
>>> +  qcom,qaccept-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>> +    description:
>>> +      Phandle reference to a syscon representing TCSR followed by the
>>> +      three offsets within syscon for mdm, cx and axi qaccept registers.
>>> +
>>> +  qcom,qmp:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle
>>> +    description: Reference to the AOSS side-channel message RAM.
>>> +
>>> +  qcom,smem-states:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>> +    description: States used by the AP to signal the Hexagon core
>>> +    items:
>>> +      - description: Stop the modem
>>
>> This one did items for a phandle array so I think we should follow the
>> same above.
> 
> ack
> 
>>
>>> +
>>> +  qcom,smem-state-names:
>>> +    description: The names of the state bits used for SMP2P output
>>> +    const: stop
>>> +
>>> +  glink-edge:
>>> +    $ref: qcom,glink-edge.yaml#
>>> +    description:
>>> +      Qualcomm G-Link subnode which represents communication edge, channels
>>> +      and devices related to the DSP.
>> [..]
>>> +        power-domain-names = "cx", "mss";
>>> +
>>> +        memory-region = <&mba_mem>, <&mpss_mem>;
>>> +
>>> +        qcom,qmp = <&aoss_qmp>;
>>> +
>>> +        qcom,smem-states = <&modem_smp2p_out 0>;
>>> +        qcom,smem-state-names = "stop";
>>> +
>>> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
>>> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
>>> +        reset-names = "mss_restart", "pdc_reset";
>>> +
>>> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
>>> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
>>
>> Because it's two items I'd expect:
>> 	
>> 	<&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;
> 
> I guess both the ways work since the driver uses
> of_parse_phandle_with_fixed_args.

But only one is correct...


Best regards,
Krzysztof
Sibi Sankar May 24, 2022, 2:22 a.m. UTC | #6
On 5/21/22 1:40 AM, Stephen Boyd wrote:
> Quoting Sibi Sankar (2022-05-20 11:46:58)
>> On 5/20/22 4:05 AM, Stephen Boyd wrote:
>>> Quoting Sibi Sankar (2022-05-19 09:47:04)
>>>> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
>>>> new file mode 100644
>>>> index 000000000000..a936d84eefa6
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
>>>> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
>>>> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
>>>> +        reset-names = "mss_restart", "pdc_reset";
>>>> +
>>>> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
>>>> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
>>>
>>> Because it's two items I'd expect:
>>>
>>>        <&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;
>>
>> I guess both the ways work since the driver uses
>> of_parse_phandle_with_fixed_args.
> 
> See commit 39bd2b6a3783 ("dt-bindings: Improve phandle-array schemas")
> for why the way you have it is not preferred.

Sure, I'll fix the dt up and update the example.

-Sibi

>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
index b677900b3aae..1ec9093c3a82 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
@@ -15,7 +15,6 @@  on the Qualcomm Hexagon core.
 		    "qcom,msm8996-mss-pil"
 		    "qcom,msm8998-mss-pil"
 		    "qcom,sc7180-mss-pil"
-		    "qcom,sc7280-mss-pil"
 		    "qcom,sdm845-mss-pil"
 
 - reg:
@@ -48,7 +47,6 @@  on the Qualcomm Hexagon core.
 	qcom,msm8996-mss-pil:
 	qcom,msm8998-mss-pil:
 	qcom,sc7180-mss-pil:
-	qcom,sc7280-mss-pil:
 	qcom,sdm845-mss-pil:
 		    must be "wdog", "fatal", "ready", "handover", "stop-ack",
 		    "shutdown-ack"
@@ -89,8 +87,6 @@  on the Qualcomm Hexagon core.
 	qcom,sc7180-mss-pil:
 		    must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi",
 		    "nav"
-	qcom,sc7280-mss-pil:
-		    must be "iface", "xo", "snoc_axi", "offline", "pka"
 	qcom,sdm845-mss-pil:
 		    must be "iface", "bus", "mem", "xo", "gpll0_mss",
 		    "snoc_axi", "mnoc_axi", "prng"
@@ -102,7 +98,7 @@  on the Qualcomm Hexagon core.
 		    reference to the list of 3 reset-controllers for the
 		    wcss sub-system
 		    reference to the list of 2 reset-controllers for the modem
-		    sub-system on SC7180, SC7280, SDM845 SoCs
+		    sub-system on SC7180, SDM845 SoCs
 
 - reset-names:
 	Usage: required
@@ -111,7 +107,7 @@  on the Qualcomm Hexagon core.
 		    must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset"
 		    for the wcss sub-system
 		    must be "mss_restart", "pdc_reset" for the modem
-		    sub-system on SC7180, SC7280, SDM845 SoCs
+		    sub-system on SC7180, SDM845 SoCs
 
 For devices where the mba and mpss sub-nodes are not specified, mba/mpss region
 should be referenced as follows:
@@ -178,8 +174,6 @@  For the compatible string below the following supplies are required:
 		    must be "cx", "mx"
 	qcom,sc7180-mss-pil:
 		    must be "cx", "mx", "mss"
-	qcom,sc7280-mss-pil:
-		    must be "cx", "mss"
 	qcom,sdm845-mss-pil:
 		    must be "cx", "mx", "mss"
 
@@ -205,9 +199,6 @@  For the compatible string below the following supplies are required:
 	Definition: a phandle reference to a syscon representing TCSR followed
 		    by the three offsets within syscon for q6, modem and nc
 		    halt registers.
-		    a phandle reference to a syscon representing TCSR followed
-		    by the four offsets within syscon for q6, modem, nc and vq6
-		    halt registers on SC7280 SoCs.
 
 For the compatible strings below the following phandle references are required:
   "qcom,sc7180-mss-pil"
@@ -218,24 +209,6 @@  For the compatible strings below the following phandle references are required:
 		    by the offset within syscon for conn_box_spare0 register
 		    used by the modem sub-system running on SC7180 SoC.
 
-For the compatible strings below the following phandle references are required:
-  "qcom,sc7280-mss-pil"
-- qcom,ext-regs:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: two phandle references to syscons representing TCSR_REG and
-		    TCSR register space followed by the two offsets within the syscon
-		    to force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off
-		    registers respectively.
-
-- qcom,qaccept-regs:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: a phandle reference to a syscon representing TCSR followed
-		    by the three offsets within syscon for mdm, cx and axi
-		    qaccept registers used by the modem sub-system running on
-		    SC7280 SoC.
-
 The Hexagon node must contain iommus property as described in ../iommu/iommu.txt
 on platforms which do not have TrustZone.
 
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
new file mode 100644
index 000000000000..a936d84eefa6
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-mss-pil.yaml
@@ -0,0 +1,250 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-mss-pil.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SC7280 MSS Peripheral Image Loader
+
+maintainers:
+  - Sibi Sankar <quic_sibis@quicinc.com>
+
+description:
+  This document describes the hardware for a component that loads and boots firmware
+  on the Qualcomm Technology Inc. SC7280 Modem Hexagon Core.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7280-mss-pil
+
+  reg:
+    items:
+      - description: MSS QDSP6 registers
+      - description: RMB registers
+
+  reg-names:
+    items:
+      - const: qdsp6
+      - const: rmb
+
+  iommus:
+    items:
+      - description: MSA Stream 1
+      - description: MSA Stream 2
+
+  interconnects:
+    items:
+      - description: Path leading to system memory
+
+  interrupts:
+    items:
+      - description: Watchdog interrupt
+      - description: Fatal interrupt
+      - description: Ready interrupt
+      - description: Handover interrupt
+      - description: Stop acknowledge interrupt
+      - description: Shutdown acknowledge interrupt
+
+  interrupt-names:
+    items:
+      - const: wdog
+      - const: fatal
+      - const: ready
+      - const: handover
+      - const: stop-ack
+      - const: shutdown-ack
+
+  clocks:
+    items:
+      - description: GCC MSS IFACE clock
+      - description: GCC MSS OFFLINE clock
+      - description: GCC MSS SNOC_AXI clock
+      - description: RPMH PKA clock
+      - description: RPMH XO clock
+
+  clock-names:
+    items:
+      - const: iface
+      - const: offline
+      - const: snoc_axi
+      - const: pka
+      - const: xo
+
+  power-domains:
+    items:
+      - description: CX power domain
+      - description: MSS power domain
+
+  power-domain-names:
+    items:
+      - const: cx
+      - const: mss
+
+  resets:
+    items:
+      - description: AOSS restart
+      - description: PDC reset
+
+  reset-names:
+    items:
+      - const: mss_restart
+      - const: pdc_reset
+
+  memory-region:
+    maxItems: 2
+    description: Phandle reference to the reserved-memory for the MBA region followed
+                 by the modem region.
+
+  firmware-name:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    maxItems: 2
+    description:
+      The name of the MBA and modem firmware to be loaded for this remote processor.
+
+  qcom,halt-regs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      Phandle reference to a syscon representing TCSR followed by the
+      four offsets within syscon for q6, modem, nc and vq6 halt registers.
+
+  qcom,ext-regs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      Two phandle references to syscons representing TCSR_REG and TCSR register
+      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
+      and axim1_clk_off/crypto_clk_off registers respectively.
+
+  qcom,qaccept-regs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      Phandle reference to a syscon representing TCSR followed by the
+      three offsets within syscon for mdm, cx and axi qaccept registers.
+
+  qcom,qmp:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Reference to the AOSS side-channel message RAM.
+
+  qcom,smem-states:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: States used by the AP to signal the Hexagon core
+    items:
+      - description: Stop the modem
+
+  qcom,smem-state-names:
+    description: The names of the state bits used for SMP2P output
+    const: stop
+
+  glink-edge:
+    $ref: qcom,glink-edge.yaml#
+    description:
+      Qualcomm G-Link subnode which represents communication edge, channels
+      and devices related to the DSP.
+
+    properties:
+      interrupts:
+        items:
+          - description: IRQ from MSS to GLINK
+
+      mboxes:
+        items:
+          - description: Mailbox for communication between APPS and MSS
+
+      label:
+        items:
+          - const: modem
+
+      apr: false
+      fastrpc: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - iommus
+  - interconnects
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - power-domains
+  - power-domain-names
+  - resets
+  - reset-names
+  - qcom,halt-regs
+  - qcom,ext-regs
+  - qcom,qaccept-regs
+  - memory-region
+  - qcom,qmp
+  - qcom,smem-states
+  - qcom,smem-state-names
+  - glink-edge
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sc7280.h>
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/interconnect/qcom,sc7280.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/mailbox/qcom-ipcc.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+    #include <dt-bindings/reset/qcom,sdm845-aoss.h>
+    #include <dt-bindings/reset/qcom,sdm845-pdc.h>
+
+    remoteproc_mpss: remoteproc@4080000 {
+        compatible = "qcom,sc7280-mss-pil";
+        reg = <0x04080000 0x10000>, <0x04180000 0x48>;
+        reg-names = "qdsp6", "rmb";
+
+        iommus = <&apps_smmu 0x124 0x0>, <&apps_smmu 0x488 0x7>;
+
+        interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+
+        interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+
+        interrupt-names = "wdog", "fatal", "ready", "handover",
+                          "stop-ack", "shutdown-ack";
+
+        clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+                 <&gcc GCC_MSS_OFFLINE_AXI_CLK>,
+                 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+                 <&rpmhcc RPMH_PKA_CLK>,
+                 <&rpmhcc RPMH_CXO_CLK>;
+        clock-names = "iface", "offline", "snoc_axi", "pka", "xo";
+
+        power-domains = <&rpmhpd SC7280_CX>,
+                        <&rpmhpd SC7280_MSS>;
+        power-domain-names = "cx", "mss";
+
+        memory-region = <&mba_mem>, <&mpss_mem>;
+
+        qcom,qmp = <&aoss_qmp>;
+
+        qcom,smem-states = <&modem_smp2p_out 0>;
+        qcom,smem-state-names = "stop";
+
+        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+        reset-names = "mss_restart", "pdc_reset";
+
+        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
+        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
+        qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
+
+        glink-edge {
+            interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+                                   IPCC_MPROC_SIGNAL_GLINK_QMP
+                                   IRQ_TYPE_EDGE_RISING>;
+            mboxes = <&ipcc IPCC_CLIENT_MPSS
+                      IPCC_MPROC_SIGNAL_GLINK_QMP>;
+            label = "modem";
+            qcom,remote-pid = <1>;
+        };
+    };