Message ID | 20220428230933.15262-4-andre.przywara@arm.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | arm64: sunxi: Initial Allwinner H616 SoC support | expand |
Hi! Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > This (relatively) new SoC is similar to the H6, but drops the (broken) > PCIe support and the USB 3.0 controller. It also gets the management > controller removed, which in turn removes *some*, but not all of the > devices formerly dedicated to the ARISC (CPUS). > And while there is still the extra sunxi interrupt controller, the > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > The reserved memory node is actually handled by Trusted Firmware now, > but U-Boot fails to propagate this to a separately loaded DTB, so we > keep it in here for now, until U-Boot learns to do this properly. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > 1 file changed, 574 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/ boot/dts/allwinner/sun50i-h616.dtsi > new file mode 100644 > index 000000000000..cc06cdd15ba5 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > @@ -0,0 +1,574 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2020 Arm Ltd. > +// based on the H6 dtsi, which is: > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > + > +/ { > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + cpu0: cpu@0 { > + compatible = "arm,cortex-a53"; > + device_type = "cpu"; > + reg = <0>; > + enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + }; > + > + cpu1: cpu@1 { > + compatible = "arm,cortex-a53"; > + device_type = "cpu"; > + reg = <1>; > + enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + }; > + > + cpu2: cpu@2 { > + compatible = "arm,cortex-a53"; > + device_type = "cpu"; > + reg = <2>; > + enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + }; > + > + cpu3: cpu@3 { > + compatible = "arm,cortex-a53"; > + device_type = "cpu"; > + reg = <3>; > + enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + }; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > + secmon_reserved: secmon@40000000 { > + reg = <0x0 0x40000000 0x0 0x80000>; > + no-map; > + }; > + }; I'm not a fan of above. If anything changes in future in BL31, U-Boot would need to reconfigure it anyway. Can we just skip it? > + > + osc24M: osc24M-clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <24000000>; > + clock-output-names = "osc24M"; > + }; > + > + pmu { > + compatible = "arm,cortex-a53-pmu"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > + }; > + > + psci { > + compatible = "arm,psci-0.2"; > + method = "smc"; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + arm,no-tick-in-suspend; > + interrupts = <GIC_PPI 13 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 14 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 11 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > + <GIC_PPI 10 > + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + }; Vendor kernel sets IRQ to low level. What is the difference? > + > + soc@0 { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0x0 0x0 0x0 0x40000000>; > + > + syscon: syscon@3000000 { > + compatible = "allwinner,sun50i-h616-system- control"; > + reg = <0x03000000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + sram_c: sram@28000 { > + compatible = "mmio-sram"; > + reg = <0x00028000 0x30000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x00028000 0x30000>; > + }; > + }; > + > + ccu: clock@3001000 { > + compatible = "allwinner,sun50i-h616-ccu"; > + reg = <0x03001000 0x1000>; > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > + clock-names = "hosc", "losc", "iosc"; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + watchdog: watchdog@30090a0 { > + compatible = "allwinner,sun50i-h616-wdt", > + "allwinner,sun6i-a31-wdt"; > + reg = <0x030090a0 0x20>; > + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&osc24M>; > + }; > + > + pio: pinctrl@300b000 { > + compatible = "allwinner,sun50i-h616-pinctrl"; > + reg = <0x0300b000 0x400>; > + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>; > + clock-names = "apb", "hosc", "losc"; > + gpio-controller; > + #gpio-cells = <3>; > + interrupt-controller; > + #interrupt-cells = <3>; > + > + ext_rgmii_pins: rgmii-pins { > + pins = "PI0", "PI1", "PI2", "PI3", "PI4", > + "PI5", "PI7", "PI8", "PI9", "PI10", > + "PI11", "PI12", "PI13", "PI14", "PI15", > + "PI16"; > + function = "emac0"; > + drive-strength = <40>; > + }; > + > + i2c0_pins: i2c0-pins { > + pins = "PI6", "PI7"; > + function = "i2c0"; > + }; > + > + i2c3_ph_pins: i2c3-ph-pins { > + pins = "PH4", "PH5"; > + function = "i2c3"; > + }; > + > + ir_rx_pin: ir-rx-pin { > + pins = "PH10"; > + function = "ir_rx"; > + }; > + > + mmc0_pins: mmc0-pins { > + pins = "PF0", "PF1", "PF2", "PF3", > + "PF4", "PF5"; > + function = "mmc0"; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + mmc1_pins: mmc1-pins { > + pins = "PG0", "PG1", "PG2", "PG3", > + "PG4", "PG5"; > + function = "mmc1"; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + mmc2_pins: mmc2-pins { > + pins = "PC0", "PC1", "PC5", "PC6", > + "PC8", "PC9", "PC10", "PC11", > + "PC13", "PC14", "PC15", "PC16"; > + function = "mmc2"; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + spi0_pins: spi0-pins { > + pins = "PC0", "PC2", "PC3", "PC4"; > + function = "spi0"; > + }; > + > + spi1_pins: spi1-pins { > + pins = "PH6", "PH7", "PH8"; > + function = "spi1"; > + }; > + > + spi1_cs_pin: spi1-cs-pin { > + pins = "PH5"; > + function = "spi1"; > + }; > + > + uart0_ph_pins: uart0-ph-pins { > + pins = "PH0", "PH1"; > + function = "uart0"; > + }; > + > + uart1_pins: uart1-pins { > + pins = "PG6", "PG7"; > + function = "uart1"; > + }; > + > + uart1_rts_cts_pins: uart1-rts-cts-pins { > + pins = "PG8", "PG9"; > + function = "uart1"; > + }; Please add /omit-if-no-ref/ where applicable. > + }; > + > + gic: interrupt-controller@3021000 { > + compatible = "arm,gic-400"; > + reg = <0x03021000 0x1000>, > + <0x03022000 0x2000>, > + <0x03024000 0x2000>, > + <0x03026000 0x2000>; > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + interrupt-controller; > + #interrupt-cells = <3>; > + }; > + > + mmc0: mmc@4020000 { > + compatible = "allwinner,sun50i-h616-mmc", > + "allwinner,sun50i-a100-mmc"; > + reg = <0x04020000 0x1000>; > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC0>; > + reset-names = "ahb"; > + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins>; > + status = "disabled"; > + max-frequency = <150000000>; > + cap-sd-highspeed; > + cap-mmc-highspeed; > + mmc-ddr-3_3v; > + cap-sdio-irq; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + mmc1: mmc@4021000 { > + compatible = "allwinner,sun50i-h616-mmc", > + "allwinner,sun50i-a100-mmc"; > + reg = <0x04021000 0x1000>; > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC1>; > + reset-names = "ahb"; > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins>; > + status = "disabled"; > + max-frequency = <150000000>; > + cap-sd-highspeed; > + cap-mmc-highspeed; > + mmc-ddr-3_3v; > + cap-sdio-irq; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + mmc2: mmc@4022000 { > + compatible = "allwinner,sun50i-h616-emmc", > + "allwinner,sun50i-a100-emmc"; > + reg = <0x04022000 0x1000>; > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC2>; > + reset-names = "ahb"; > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; > + status = "disabled"; > + max-frequency = <150000000>; > + cap-sd-highspeed; > + cap-mmc-highspeed; > + mmc-ddr-3_3v; > + cap-sdio-irq; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + uart0: serial@5000000 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05000000 0x400>; > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART0>; > + resets = <&ccu RST_BUS_UART0>; > + status = "disabled"; > + }; > + > + uart1: serial@5000400 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05000400 0x400>; > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART1>; > + resets = <&ccu RST_BUS_UART1>; > + status = "disabled"; > + }; > + > + uart2: serial@5000800 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05000800 0x400>; > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART2>; > + resets = <&ccu RST_BUS_UART2>; > + status = "disabled"; > + }; > + > + uart3: serial@5000c00 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05000c00 0x400>; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART3>; > + resets = <&ccu RST_BUS_UART3>; > + status = "disabled"; > + }; > + > + uart4: serial@5001000 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05001000 0x400>; > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART4>; > + resets = <&ccu RST_BUS_UART4>; > + status = "disabled"; > + }; > + > + uart5: serial@5001400 { > + compatible = "snps,dw-apb-uart"; > + reg = <0x05001400 0x400>; > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART5>; > + resets = <&ccu RST_BUS_UART5>; > + status = "disabled"; > + }; > + > + i2c0: i2c@5002000 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002000 0x400>; > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C0>; > + resets = <&ccu RST_BUS_I2C0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c1: i2c@5002400 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002400 0x400>; > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C1>; > + resets = <&ccu RST_BUS_I2C1>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c2: i2c@5002800 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002800 0x400>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C2>; > + resets = <&ccu RST_BUS_I2C2>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c3: i2c@5002c00 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002c00 0x400>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C3>; > + resets = <&ccu RST_BUS_I2C3>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c4: i2c@5003000 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05003000 0x400>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C4>; > + resets = <&ccu RST_BUS_I2C4>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + spi0: spi@5010000 { > + compatible = "allwinner,sun50i-h616-spi", > + "allwinner,sun8i-h3-spi"; > + reg = <0x05010000 0x1000>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; > + clock-names = "ahb", "mod"; > + resets = <&ccu RST_BUS_SPI0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + spi1: spi@5011000 { > + compatible = "allwinner,sun50i-h616-spi", > + "allwinner,sun8i-h3-spi"; > + reg = <0x05011000 0x1000>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; > + clock-names = "ahb", "mod"; > + resets = <&ccu RST_BUS_SPI1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi1_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + emac0: ethernet@5020000 { > + compatible = "allwinner,sun50i-h616-emac", > + "allwinner,sun50i-a64-emac"; > + syscon = <&syscon>; > + reg = <0x05020000 0x10000>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "macirq"; > + resets = <&ccu RST_BUS_EMAC0>; > + reset-names = "stmmaceth"; > + clocks = <&ccu CLK_BUS_EMAC0>; > + clock-names = "stmmaceth"; > + status = "disabled"; > + > + mdio0: mdio { > + compatible = "snps,dwmac-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + rtc: rtc@7000000 { > + compatible = "allwinner,sun50i-h616-rtc"; > + reg = <0x07000000 0x400>; > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; Above interrupt doesn't seem to be correct according to documentation. It should be 104. > + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>, > + <&ccu CLK_PLL_SYSTEM_32K>; > + clock-names = "bus", "hosc", > + "pll-32k"; > + clock-output-names = "osc32k", "osc32k-out", "iosc"; > + #clock-cells = <1>; > + }; > + > + r_ccu: clock@7010000 { > + compatible = "allwinner,sun50i-h616-r-ccu"; > + reg = <0x07010000 0x210>; > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > + <&ccu CLK_PLL_PERIPH0>; > + clock-names = "hosc", "losc", "iosc", "pll- periph"; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + r_pio: pinctrl@7022000 { > + compatible = "allwinner,sun50i-h616-r- pinctrl"; > + reg = <0x07022000 0x400>; > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; Above interrupt is already used for port E in first pinctrl. Is this shared somehow? Best regards, Jernej > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; > + clock-names = "apb", "hosc", "losc"; > + gpio-controller; > + #gpio-cells = <3>; > + interrupt-controller; > + #interrupt-cells = <3>; > + > + r_i2c_pins: r-i2c-pins { > + pins = "PL0", "PL1"; > + function = "s_i2c"; > + }; > + > + r_rsb_pins: r-rsb-pins { > + pins = "PL0", "PL1"; > + function = "s_rsb"; > + }; > + }; > + > + ir: ir@7040000 { > + compatible = "allwinner,sun50i-h616-ir", > + "allwinner,sun6i-a31-ir"; > + reg = <0x07040000 0x400>; > + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&r_ccu CLK_R_APB1_IR>, > + <&r_ccu CLK_IR>; > + clock-names = "apb", "ir"; > + resets = <&r_ccu RST_R_APB1_IR>; > + pinctrl-names = "default"; > + pinctrl-0 = <&ir_rx_pin>; > + status = "disabled"; > + }; > + > + r_i2c: i2c@7081400 { > + compatible = "allwinner,sun50i-h616-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x07081400 0x400>; > + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&r_ccu CLK_R_APB2_I2C>; > + resets = <&r_ccu RST_R_APB2_I2C>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + r_rsb: rsb@7083000 { > + compatible = "allwinner,sun50i-h616-rsb", > + "allwinner,sun8i-a23-rsb"; > + reg = <0x07083000 0x400>; > + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&r_ccu CLK_R_APB2_RSB>; > + clock-frequency = <3000000>; > + resets = <&r_ccu RST_R_APB2_RSB>; > + pinctrl-names = "default"; > + pinctrl-0 = <&r_rsb_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > +}; > -- > 2.35.3 > >
Dne torek, 03. maj 2022 ob 21:05:11 CEST je Jernej Škrabec napisal(a): > Hi! > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > > This (relatively) new SoC is similar to the H6, but drops the (broken) > > PCIe support and the USB 3.0 controller. It also gets the management > > controller removed, which in turn removes *some*, but not all of the > > devices formerly dedicated to the ARISC (CPUS). > > And while there is still the extra sunxi interrupt controller, the > > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > > > The reserved memory node is actually handled by Trusted Firmware now, > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > keep it in here for now, until U-Boot learns to do this properly. > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > --- > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > > 1 file changed, 574 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/ > boot/dts/allwinner/sun50i-h616.dtsi > > new file mode 100644 > > index 000000000000..cc06cdd15ba5 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > @@ -0,0 +1,574 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2020 Arm Ltd. > > +// based on the H6 dtsi, which is: > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > + > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > + > > +/ { > > + interrupt-parent = <&gic>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu0: cpu@0 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <0>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu1: cpu@1 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <1>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu2: cpu@2 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <2>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu3: cpu@3 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <3>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > + secmon_reserved: secmon@40000000 { > > + reg = <0x0 0x40000000 0x0 0x80000>; > > + no-map; > > + }; > > + }; > > I'm not a fan of above. If anything changes in future in BL31, U-Boot would > need to reconfigure it anyway. Can we just skip it? > > > + > > + osc24M: osc24M-clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <24000000>; > > + clock-output-names = "osc24M"; > > + }; > > + > > + pmu { > > + compatible = "arm,cortex-a53-pmu"; > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > > + }; > > + > > + psci { > > + compatible = "arm,psci-0.2"; > > + method = "smc"; > > + }; > > + > > + timer { > > + compatible = "arm,armv8-timer"; > > + arm,no-tick-in-suspend; > > + interrupts = <GIC_PPI 13 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 14 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 11 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 10 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>; > > + }; > > Vendor kernel sets IRQ to low level. What is the difference? > > > + > > + soc@0 { > > + compatible = "simple-bus"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0x0 0x0 0x0 0x40000000>; > > + > > + syscon: syscon@3000000 { > > + compatible = "allwinner,sun50i-h616-system- > control"; > > + reg = <0x03000000 0x1000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + sram_c: sram@28000 { > > + compatible = "mmio-sram"; > > + reg = <0x00028000 0x30000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0 0x00028000 0x30000>; > > + }; > > + }; > > + > > + ccu: clock@3001000 { > > + compatible = "allwinner,sun50i-h616-ccu"; > > + reg = <0x03001000 0x1000>; > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > > + clock-names = "hosc", "losc", "iosc"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + watchdog: watchdog@30090a0 { > > + compatible = "allwinner,sun50i-h616-wdt", > > + "allwinner,sun6i-a31-wdt"; > > + reg = <0x030090a0 0x20>; > > + interrupts = <GIC_SPI 50 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&osc24M>; > > + }; > > + > > + pio: pinctrl@300b000 { > > + compatible = "allwinner,sun50i-h616- pinctrl"; > > + reg = <0x0300b000 0x400>; > > + interrupts = <GIC_SPI 51 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 52 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 53 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 43 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 54 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 55 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 56 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 57 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc > 0>; > > + clock-names = "apb", "hosc", "losc"; > > + gpio-controller; > > + #gpio-cells = <3>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + > > + ext_rgmii_pins: rgmii-pins { > > + pins = "PI0", "PI1", "PI2", "PI3", > "PI4", > > + "PI5", "PI7", "PI8", "PI9", > "PI10", > > + "PI11", "PI12", "PI13", > "PI14", "PI15", > > + "PI16"; > > + function = "emac0"; > > + drive-strength = <40>; > > + }; > > + > > + i2c0_pins: i2c0-pins { > > + pins = "PI6", "PI7"; > > + function = "i2c0"; > > + }; > > + > > + i2c3_ph_pins: i2c3-ph-pins { > > + pins = "PH4", "PH5"; > > + function = "i2c3"; > > + }; > > + > > + ir_rx_pin: ir-rx-pin { > > + pins = "PH10"; > > + function = "ir_rx"; > > + }; > > + > > + mmc0_pins: mmc0-pins { > > + pins = "PF0", "PF1", "PF2", "PF3", > > + "PF4", "PF5"; > > + function = "mmc0"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + mmc1_pins: mmc1-pins { > > + pins = "PG0", "PG1", "PG2", "PG3", > > + "PG4", "PG5"; > > + function = "mmc1"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + mmc2_pins: mmc2-pins { > > + pins = "PC0", "PC1", "PC5", "PC6", > > + "PC8", "PC9", "PC10", > "PC11", > > + "PC13", "PC14", "PC15", > "PC16"; > > + function = "mmc2"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + spi0_pins: spi0-pins { > > + pins = "PC0", "PC2", "PC3", "PC4"; > > + function = "spi0"; > > + }; > > + > > + spi1_pins: spi1-pins { > > + pins = "PH6", "PH7", "PH8"; > > + function = "spi1"; > > + }; > > + > > + spi1_cs_pin: spi1-cs-pin { > > + pins = "PH5"; > > + function = "spi1"; > > + }; > > + > > + uart0_ph_pins: uart0-ph-pins { > > + pins = "PH0", "PH1"; > > + function = "uart0"; > > + }; > > + > > + uart1_pins: uart1-pins { > > + pins = "PG6", "PG7"; > > + function = "uart1"; > > + }; > > + > > + uart1_rts_cts_pins: uart1-rts-cts-pins { > > + pins = "PG8", "PG9"; > > + function = "uart1"; > > + }; > > Please add /omit-if-no-ref/ where applicable. > > > + }; > > + > > + gic: interrupt-controller@3021000 { > > + compatible = "arm,gic-400"; > > + reg = <0x03021000 0x1000>, > > + <0x03022000 0x2000>, > > + <0x03024000 0x2000>, > > + <0x03026000 0x2000>; > > + interrupts = <GIC_PPI 9 > (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + }; > > + > > + mmc0: mmc@4020000 { > > + compatible = "allwinner,sun50i-h616-mmc", > > + "allwinner,sun50i-a100-mmc"; > > + reg = <0x04020000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu > CLK_MMC0>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC0>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 35 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc0_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc1: mmc@4021000 { > > + compatible = "allwinner,sun50i-h616-mmc", > > + "allwinner,sun50i-a100-mmc"; > > + reg = <0x04021000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu > CLK_MMC1>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC1>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 36 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc1_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc2: mmc@4022000 { > > + compatible = "allwinner,sun50i-h616-emmc", > > + "allwinner,sun50i-a100- emmc"; > > + reg = <0x04022000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu > CLK_MMC2>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC2>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 37 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc2_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + uart0: serial@5000000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000000 0x400>; > > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART0>; > > + resets = <&ccu RST_BUS_UART0>; > > + status = "disabled"; > > + }; > > + > > + uart1: serial@5000400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000400 0x400>; > > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART1>; > > + resets = <&ccu RST_BUS_UART1>; > > + status = "disabled"; > > + }; > > + > > + uart2: serial@5000800 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000800 0x400>; > > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART2>; > > + resets = <&ccu RST_BUS_UART2>; > > + status = "disabled"; > > + }; > > + > > + uart3: serial@5000c00 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000c00 0x400>; > > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART3>; > > + resets = <&ccu RST_BUS_UART3>; > > + status = "disabled"; > > + }; > > + > > + uart4: serial@5001000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05001000 0x400>; > > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART4>; > > + resets = <&ccu RST_BUS_UART4>; > > + status = "disabled"; > > + }; > > + > > + uart5: serial@5001400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05001400 0x400>; > > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART5>; > > + resets = <&ccu RST_BUS_UART5>; > > + status = "disabled"; > > + }; > > + > > + i2c0: i2c@5002000 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002000 0x400>; > > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C0>; > > + resets = <&ccu RST_BUS_I2C0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c0_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c1: i2c@5002400 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002400 0x400>; > > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C1>; > > + resets = <&ccu RST_BUS_I2C1>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c2: i2c@5002800 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002800 0x400>; > > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C2>; > > + resets = <&ccu RST_BUS_I2C2>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c3: i2c@5002c00 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002c00 0x400>; > > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C3>; > > + resets = <&ccu RST_BUS_I2C3>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c4: i2c@5003000 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05003000 0x400>; > > + interrupts = <GIC_SPI 10 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C4>; > > + resets = <&ccu RST_BUS_I2C4>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi0: spi@5010000 { > > + compatible = "allwinner,sun50i-h616-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05010000 0x1000>; > > + interrupts = <GIC_SPI 12 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu > CLK_SPI0>; > > + clock-names = "ahb", "mod"; > > + resets = <&ccu RST_BUS_SPI0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&spi0_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi1: spi@5011000 { > > + compatible = "allwinner,sun50i-h616-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05011000 0x1000>; > > + interrupts = <GIC_SPI 13 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu > CLK_SPI1>; > > + clock-names = "ahb", "mod"; > > + resets = <&ccu RST_BUS_SPI1>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&spi1_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; Please remove default pins for SPI controllers. There are few different combinations possible, so better add them in board DT files. Best regards, Jernej > > + > > + emac0: ethernet@5020000 { > > + compatible = "allwinner,sun50i-h616-emac", > > + "allwinner,sun50i-a64-emac"; > > + syscon = <&syscon>; > > + reg = <0x05020000 0x10000>; > > + interrupts = <GIC_SPI 14 > IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "macirq"; > > + resets = <&ccu RST_BUS_EMAC0>; > > + reset-names = "stmmaceth"; > > + clocks = <&ccu CLK_BUS_EMAC0>; > > + clock-names = "stmmaceth"; > > + status = "disabled"; > > + > > + mdio0: mdio { > > + compatible = "snps,dwmac-mdio"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > + > > + rtc: rtc@7000000 { > > + compatible = "allwinner,sun50i-h616-rtc"; > > + reg = <0x07000000 0x400>; > > + interrupts = <GIC_SPI 101 > IRQ_TYPE_LEVEL_HIGH>; > > Above interrupt doesn't seem to be correct according to documentation. It > should be 104. > > > + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>, > > + <&ccu CLK_PLL_SYSTEM_32K>; > > + clock-names = "bus", "hosc", > > + "pll-32k"; > > + clock-output-names = "osc32k", "osc32k-out", > "iosc"; > > + #clock-cells = <1>; > > + }; > > + > > + r_ccu: clock@7010000 { > > + compatible = "allwinner,sun50i-h616-r-ccu"; > > + reg = <0x07010000 0x210>; > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > > + <&ccu CLK_PLL_PERIPH0>; > > + clock-names = "hosc", "losc", "iosc", "pll- > periph"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + r_pio: pinctrl@7022000 { > > + compatible = "allwinner,sun50i-h616-r- > pinctrl"; > > + reg = <0x07022000 0x400>; > > + interrupts = <GIC_SPI 43 > IRQ_TYPE_LEVEL_HIGH>; > > Above interrupt is already used for port E in first pinctrl. Is this shared > somehow? > > Best regards, > Jernej > > > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, > <&rtc 0>; > > + clock-names = "apb", "hosc", "losc"; > > + gpio-controller; > > + #gpio-cells = <3>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + > > + r_i2c_pins: r-i2c-pins { > > + pins = "PL0", "PL1"; > > + function = "s_i2c"; > > + }; > > + > > + r_rsb_pins: r-rsb-pins { > > + pins = "PL0", "PL1"; > > + function = "s_rsb"; > > + }; > > + }; > > + > > + ir: ir@7040000 { > > + compatible = "allwinner,sun50i-h616-ir", > > + "allwinner,sun6i-a31-ir"; > > + reg = <0x07040000 0x400>; > > + interrupts = <GIC_SPI 106 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB1_IR>, > > + <&r_ccu CLK_IR>; > > + clock-names = "apb", "ir"; > > + resets = <&r_ccu RST_R_APB1_IR>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ir_rx_pin>; > > + status = "disabled"; > > + }; > > + > > + r_i2c: i2c@7081400 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x07081400 0x400>; > > + interrupts = <GIC_SPI 105 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB2_I2C>; > > + resets = <&r_ccu RST_R_APB2_I2C>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + r_rsb: rsb@7083000 { > > + compatible = "allwinner,sun50i-h616-rsb", > > + "allwinner,sun8i-a23-rsb"; > > + reg = <0x07083000 0x400>; > > + interrupts = <GIC_SPI 109 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB2_RSB>; > > + clock-frequency = <3000000>; > > + resets = <&r_ccu RST_R_APB2_RSB>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&r_rsb_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > +}; > > -- > > 2.35.3 > > > > > > >
On Tue, 03 May 2022 21:05:11 +0200 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, many thanks for taking the time to wade through this file! > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > > This (relatively) new SoC is similar to the H6, but drops the (broken) > > PCIe support and the USB 3.0 controller. It also gets the management > > controller removed, which in turn removes *some*, but not all of the > > devices formerly dedicated to the ARISC (CPUS). > > And while there is still the extra sunxi interrupt controller, the > > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > > > The reserved memory node is actually handled by Trusted Firmware now, > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > keep it in here for now, until U-Boot learns to do this properly. > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > --- > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > > 1 file changed, 574 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/ > boot/dts/allwinner/sun50i-h616.dtsi > > new file mode 100644 > > index 000000000000..cc06cdd15ba5 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > @@ -0,0 +1,574 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2020 Arm Ltd. > > +// based on the H6 dtsi, which is: > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > + > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > + > > +/ { > > + interrupt-parent = <&gic>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu0: cpu@0 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <0>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu1: cpu@1 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <1>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu2: cpu@2 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <2>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + > > + cpu3: cpu@3 { > > + compatible = "arm,cortex-a53"; > > + device_type = "cpu"; > > + reg = <3>; > > + enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + }; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > + secmon_reserved: secmon@40000000 { > > + reg = <0x0 0x40000000 0x0 0x80000>; > > + no-map; > > + }; > > + }; > > I'm not a fan of above. If anything changes in future in BL31, U-Boot would > need to reconfigure it anyway. Can we just skip it? I am not a fan neither, but last time I checked this is needed to boot. Indeed TF-A inserts this node, with the right values, into U-Boot's DT. And that's nicely preserved if you use that DT ($fdtcontroladdr) for the kernel as well. But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then U-Boot fails to propagate the /reserved-memory node into that copy. There does not seem to be a global notion of reserved memory in U-Boot. Some commands (like tftp) explicitly parse the control DT to find and respect reserved memory regions. bootm does that also, but only to avoid placing the ramdisk or DTB into reserved memory. The information ends up in images->lmb, but is not used to generate or amend nodes in the target DT. So the bits and pieces are there, but it will require some code to be added to the generic U-Boot code. So what do you think? Leaving this out will prevent loading DTBs into U-Boot, at the moment, which sounds bad. I suggest we keep it in, for now, it should not really hurt. U-Boot will hopefully start to do the right thing soon, then we can either phase it out here (maybe when we actually change something in TF-A), or let U-Boot fix it. > > > + > > + osc24M: osc24M-clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <24000000>; > > + clock-output-names = "osc24M"; > > + }; > > + > > + pmu { > > + compatible = "arm,cortex-a53-pmu"; > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > > + }; > > + > > + psci { > > + compatible = "arm,psci-0.2"; > > + method = "smc"; > > + }; > > + > > + timer { > > + compatible = "arm,armv8-timer"; > > + arm,no-tick-in-suspend; > > + interrupts = <GIC_PPI 13 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 14 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 11 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>, > > + <GIC_PPI 10 > > + (GIC_CPU_MASK_SIMPLE(4) | > IRQ_TYPE_LEVEL_HIGH)>; > > + }; > > Vendor kernel sets IRQ to low level. What is the difference? Nothing, really. The polarity of SPI level IRQ lines is hardwired at integration time, both at the peripheral and the GIC distributor. The GIC software interface has no register to control that - all you can configure is edge or level. There *is* some underlying polarity, but to my understanding this is just mentioned here for completeness, and because the binding requires to name one. > > > + > > + soc@0 { > > + compatible = "simple-bus"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0x0 0x0 0x0 0x40000000>; > > + > > + syscon: syscon@3000000 { > > + compatible = "allwinner,sun50i-h616-system- > control"; > > + reg = <0x03000000 0x1000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + sram_c: sram@28000 { > > + compatible = "mmio-sram"; > > + reg = <0x00028000 0x30000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0 0x00028000 0x30000>; > > + }; > > + }; > > + > > + ccu: clock@3001000 { > > + compatible = "allwinner,sun50i-h616-ccu"; > > + reg = <0x03001000 0x1000>; > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > > + clock-names = "hosc", "losc", "iosc"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + watchdog: watchdog@30090a0 { > > + compatible = "allwinner,sun50i-h616-wdt", > > + "allwinner,sun6i-a31-wdt"; > > + reg = <0x030090a0 0x20>; > > + interrupts = <GIC_SPI 50 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&osc24M>; > > + }; > > + > > + pio: pinctrl@300b000 { > > + compatible = "allwinner,sun50i-h616-pinctrl"; > > + reg = <0x0300b000 0x400>; > > + interrupts = <GIC_SPI 51 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 52 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 53 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 43 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 54 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 55 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 56 > IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 57 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc > 0>; > > + clock-names = "apb", "hosc", "losc"; > > + gpio-controller; > > + #gpio-cells = <3>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + > > + ext_rgmii_pins: rgmii-pins { > > + pins = "PI0", "PI1", "PI2", "PI3", > "PI4", > > + "PI5", "PI7", "PI8", "PI9", > "PI10", > > + "PI11", "PI12", "PI13", > "PI14", "PI15", > > + "PI16"; > > + function = "emac0"; > > + drive-strength = <40>; > > + }; > > + > > + i2c0_pins: i2c0-pins { > > + pins = "PI6", "PI7"; > > + function = "i2c0"; > > + }; > > + > > + i2c3_ph_pins: i2c3-ph-pins { > > + pins = "PH4", "PH5"; > > + function = "i2c3"; > > + }; > > + > > + ir_rx_pin: ir-rx-pin { > > + pins = "PH10"; > > + function = "ir_rx"; > > + }; > > + > > + mmc0_pins: mmc0-pins { > > + pins = "PF0", "PF1", "PF2", "PF3", > > + "PF4", "PF5"; > > + function = "mmc0"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + mmc1_pins: mmc1-pins { > > + pins = "PG0", "PG1", "PG2", "PG3", > > + "PG4", "PG5"; > > + function = "mmc1"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + mmc2_pins: mmc2-pins { > > + pins = "PC0", "PC1", "PC5", "PC6", > > + "PC8", "PC9", "PC10", > "PC11", > > + "PC13", "PC14", "PC15", > "PC16"; > > + function = "mmc2"; > > + drive-strength = <30>; > > + bias-pull-up; > > + }; > > + > > + spi0_pins: spi0-pins { > > + pins = "PC0", "PC2", "PC3", "PC4"; > > + function = "spi0"; > > + }; > > + > > + spi1_pins: spi1-pins { > > + pins = "PH6", "PH7", "PH8"; > > + function = "spi1"; > > + }; > > + > > + spi1_cs_pin: spi1-cs-pin { > > + pins = "PH5"; > > + function = "spi1"; > > + }; > > + > > + uart0_ph_pins: uart0-ph-pins { > > + pins = "PH0", "PH1"; > > + function = "uart0"; > > + }; > > + > > + uart1_pins: uart1-pins { > > + pins = "PG6", "PG7"; > > + function = "uart1"; > > + }; > > + > > + uart1_rts_cts_pins: uart1-rts-cts-pins { > > + pins = "PG8", "PG9"; > > + function = "uart1"; > > + }; > > Please add /omit-if-no-ref/ where applicable. OK. I think most boards have Bluetooth at UART1, though. > > > + }; > > + > > + gic: interrupt-controller@3021000 { > > + compatible = "arm,gic-400"; > > + reg = <0x03021000 0x1000>, > > + <0x03022000 0x2000>, > > + <0x03024000 0x2000>, > > + <0x03026000 0x2000>; > > + interrupts = <GIC_PPI 9 > (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + }; > > + > > + mmc0: mmc@4020000 { > > + compatible = "allwinner,sun50i-h616-mmc", > > + "allwinner,sun50i-a100-mmc"; > > + reg = <0x04020000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu > CLK_MMC0>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC0>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 35 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc0_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc1: mmc@4021000 { > > + compatible = "allwinner,sun50i-h616-mmc", > > + "allwinner,sun50i-a100-mmc"; > > + reg = <0x04021000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu > CLK_MMC1>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC1>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 36 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc1_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + mmc2: mmc@4022000 { > > + compatible = "allwinner,sun50i-h616-emmc", > > + "allwinner,sun50i-a100-emmc"; > > + reg = <0x04022000 0x1000>; > > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu > CLK_MMC2>; > > + clock-names = "ahb", "mmc"; > > + resets = <&ccu RST_BUS_MMC2>; > > + reset-names = "ahb"; > > + interrupts = <GIC_SPI 37 > IRQ_TYPE_LEVEL_HIGH>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc2_pins>; > > + status = "disabled"; > > + max-frequency = <150000000>; > > + cap-sd-highspeed; > > + cap-mmc-highspeed; > > + mmc-ddr-3_3v; > > + cap-sdio-irq; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + uart0: serial@5000000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000000 0x400>; > > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART0>; > > + resets = <&ccu RST_BUS_UART0>; > > + status = "disabled"; > > + }; > > + > > + uart1: serial@5000400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000400 0x400>; > > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART1>; > > + resets = <&ccu RST_BUS_UART1>; > > + status = "disabled"; > > + }; > > + > > + uart2: serial@5000800 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000800 0x400>; > > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART2>; > > + resets = <&ccu RST_BUS_UART2>; > > + status = "disabled"; > > + }; > > + > > + uart3: serial@5000c00 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05000c00 0x400>; > > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART3>; > > + resets = <&ccu RST_BUS_UART3>; > > + status = "disabled"; > > + }; > > + > > + uart4: serial@5001000 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05001000 0x400>; > > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART4>; > > + resets = <&ccu RST_BUS_UART4>; > > + status = "disabled"; > > + }; > > + > > + uart5: serial@5001400 { > > + compatible = "snps,dw-apb-uart"; > > + reg = <0x05001400 0x400>; > > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > > + reg-shift = <2>; > > + reg-io-width = <4>; > > + clocks = <&ccu CLK_BUS_UART5>; > > + resets = <&ccu RST_BUS_UART5>; > > + status = "disabled"; > > + }; > > + > > + i2c0: i2c@5002000 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002000 0x400>; > > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C0>; > > + resets = <&ccu RST_BUS_I2C0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c0_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c1: i2c@5002400 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002400 0x400>; > > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C1>; > > + resets = <&ccu RST_BUS_I2C1>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c2: i2c@5002800 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002800 0x400>; > > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C2>; > > + resets = <&ccu RST_BUS_I2C2>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c3: i2c@5002c00 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002c00 0x400>; > > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C3>; > > + resets = <&ccu RST_BUS_I2C3>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c4: i2c@5003000 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05003000 0x400>; > > + interrupts = <GIC_SPI 10 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C4>; > > + resets = <&ccu RST_BUS_I2C4>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi0: spi@5010000 { > > + compatible = "allwinner,sun50i-h616-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05010000 0x1000>; > > + interrupts = <GIC_SPI 12 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu > CLK_SPI0>; > > + clock-names = "ahb", "mod"; > > + resets = <&ccu RST_BUS_SPI0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&spi0_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi1: spi@5011000 { > > + compatible = "allwinner,sun50i-h616-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05011000 0x1000>; > > + interrupts = <GIC_SPI 13 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu > CLK_SPI1>; > > + clock-names = "ahb", "mod"; > > + resets = <&ccu RST_BUS_SPI1>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&spi1_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + emac0: ethernet@5020000 { > > + compatible = "allwinner,sun50i-h616-emac", > > + "allwinner,sun50i-a64-emac"; > > + syscon = <&syscon>; > > + reg = <0x05020000 0x10000>; > > + interrupts = <GIC_SPI 14 > IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "macirq"; > > + resets = <&ccu RST_BUS_EMAC0>; > > + reset-names = "stmmaceth"; > > + clocks = <&ccu CLK_BUS_EMAC0>; > > + clock-names = "stmmaceth"; > > + status = "disabled"; > > + > > + mdio0: mdio { > > + compatible = "snps,dwmac-mdio"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > + > > + rtc: rtc@7000000 { > > + compatible = "allwinner,sun50i-h616-rtc"; > > + reg = <0x07000000 0x400>; > > + interrupts = <GIC_SPI 101 > IRQ_TYPE_LEVEL_HIGH>; > > Above interrupt doesn't seem to be correct according to documentation. It > should be 104. That is a very good catch, 101/133 is indeed the RTC IRQ number on the H6. > > > + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>, > > + <&ccu CLK_PLL_SYSTEM_32K>; > > + clock-names = "bus", "hosc", > > + "pll-32k"; > > + clock-output-names = "osc32k", "osc32k-out", > "iosc"; > > + #clock-cells = <1>; > > + }; > > + > > + r_ccu: clock@7010000 { > > + compatible = "allwinner,sun50i-h616-r-ccu"; > > + reg = <0x07010000 0x210>; > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > > + <&ccu CLK_PLL_PERIPH0>; > > + clock-names = "hosc", "losc", "iosc", "pll- > periph"; > > + #clock-cells = <1>; > > + #reset-cells = <1>; > > + }; > > + > > + r_pio: pinctrl@7022000 { > > + compatible = "allwinner,sun50i-h616-r- > pinctrl"; > > + reg = <0x07022000 0x400>; > > + interrupts = <GIC_SPI 43 > IRQ_TYPE_LEVEL_HIGH>; > > Above interrupt is already used for port E in first pinctrl. Is this shared > somehow? Huh, another good find. The manual does not seem to mention a GPIO_L interrupt, and the two PL pins do not report function 6. when probing the registers in U-Boot there are no other pins (neither in PortL nor PortM), also the interrupt registers (@+0x200) are not implemented. So there does not seem to be an interrupt. The pinctrl driver does not seem to care (by looking at the code, and by booting it), as .irq_banks is 0, so no IRQ controller functionality is ever instantiated. The binding makes the interrupts property mandatory, though, so this needs to be amended there. I will try to post a new version till the end of the week. Thanks! Andre > > Best regards, > Jernej > > > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, > <&rtc 0>; > > + clock-names = "apb", "hosc", "losc"; > > + gpio-controller; > > + #gpio-cells = <3>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + > > + r_i2c_pins: r-i2c-pins { > > + pins = "PL0", "PL1"; > > + function = "s_i2c"; > > + }; > > + > > + r_rsb_pins: r-rsb-pins { > > + pins = "PL0", "PL1"; > > + function = "s_rsb"; > > + }; > > + }; > > + > > + ir: ir@7040000 { > > + compatible = "allwinner,sun50i-h616-ir", > > + "allwinner,sun6i-a31-ir"; > > + reg = <0x07040000 0x400>; > > + interrupts = <GIC_SPI 106 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB1_IR>, > > + <&r_ccu CLK_IR>; > > + clock-names = "apb", "ir"; > > + resets = <&r_ccu RST_R_APB1_IR>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ir_rx_pin>; > > + status = "disabled"; > > + }; > > + > > + r_i2c: i2c@7081400 { > > + compatible = "allwinner,sun50i-h616-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x07081400 0x400>; > > + interrupts = <GIC_SPI 105 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB2_I2C>; > > + resets = <&r_ccu RST_R_APB2_I2C>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + r_rsb: rsb@7083000 { > > + compatible = "allwinner,sun50i-h616-rsb", > > + "allwinner,sun8i-a23-rsb"; > > + reg = <0x07083000 0x400>; > > + interrupts = <GIC_SPI 109 > IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB2_RSB>; > > + clock-frequency = <3000000>; > > + resets = <&r_ccu RST_R_APB2_RSB>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&r_rsb_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > +}; > > -- > > 2.35.3 > > > > > > >
Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > On Tue, 03 May 2022 21:05:11 +0200 > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > Hi Jernej, > > many thanks for taking the time to wade through this file! > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > > > This (relatively) new SoC is similar to the H6, but drops the (broken) > > > PCIe support and the USB 3.0 controller. It also gets the management > > > controller removed, which in turn removes *some*, but not all of the > > > devices formerly dedicated to the ARISC (CPUS). > > > And while there is still the extra sunxi interrupt controller, the > > > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > > > > > The reserved memory node is actually handled by Trusted Firmware now, > > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > > keep it in here for now, until U-Boot learns to do this properly. > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > --- > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > > > 1 file changed, 574 insertions(+) > > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > b/arch/arm64/ > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > new file mode 100644 > > > index 000000000000..cc06cdd15ba5 > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > @@ -0,0 +1,574 @@ > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > +// Copyright (C) 2020 Arm Ltd. > > > +// based on the H6 dtsi, which is: > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > + > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > + > > > +/ { > > > + interrupt-parent = <&gic>; > > > + #address-cells = <2>; > > > + #size-cells = <2>; > > > + > > > + cpus { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + cpu0: cpu@0 { > > > + compatible = "arm,cortex-a53"; > > > + device_type = "cpu"; > > > + reg = <0>; > > > + enable-method = "psci"; > > > + clocks = <&ccu CLK_CPUX>; > > > + }; > > > + > > > + cpu1: cpu@1 { > > > + compatible = "arm,cortex-a53"; > > > + device_type = "cpu"; > > > + reg = <1>; > > > + enable-method = "psci"; > > > + clocks = <&ccu CLK_CPUX>; > > > + }; > > > + > > > + cpu2: cpu@2 { > > > + compatible = "arm,cortex-a53"; > > > + device_type = "cpu"; > > > + reg = <2>; > > > + enable-method = "psci"; > > > + clocks = <&ccu CLK_CPUX>; > > > + }; > > > + > > > + cpu3: cpu@3 { > > > + compatible = "arm,cortex-a53"; > > > + device_type = "cpu"; > > > + reg = <3>; > > > + enable-method = "psci"; > > > + clocks = <&ccu CLK_CPUX>; > > > + }; > > > + }; > > > + > > > + reserved-memory { > > > + #address-cells = <2>; > > > + #size-cells = <2>; > > > + ranges; > > > + > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > > + secmon_reserved: secmon@40000000 { > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > + no-map; > > > + }; > > > + }; > > > > I'm not a fan of above. If anything changes in future in BL31, U-Boot > > would > > need to reconfigure it anyway. Can we just skip it? > > I am not a fan neither, but last time I checked this is needed to boot. > Indeed TF-A inserts this node, with the right values, into U-Boot's DT. > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > the kernel as well. > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > U-Boot fails to propagate the /reserved-memory node into that copy. > There does not seem to be a global notion of reserved memory in U-Boot. > Some commands (like tftp) explicitly parse the control DT to find and > respect reserved memory regions. bootm does that also, but only to > avoid placing the ramdisk or DTB into reserved memory. The information > ends up in images->lmb, but is not used to generate or amend nodes in > the target DT. > So the bits and pieces are there, but it will require some code to be > added to the generic U-Boot code. > > So what do you think? Leaving this out will prevent loading DTBs into > U-Boot, at the moment, which sounds bad. I suggest we keep it in, for > now, it should not really hurt. U-Boot will hopefully start to do the > right thing soon, then we can either phase it out here (maybe when we > actually change something in TF-A), or let U-Boot fix it. TBH, if "soon" is really soon, I would rather wait with H616 DT until U-Boot supports carrying over reserved memory nodes. Whatever we do now, it will have compatibility issues. If we introduce reserved memory node now, we can't easily drop it later. Bootloaders are not very often updated, but kernels and DTB files are, at least in my experience. So when we decide to drop the node? After 10 years? Alternatively, reserved memory node can be just dropped and anyone loading DTB file from outside would need to make sure it's patched. But that's unexpected from user perspective, although patching DT files is done by some distros. Best regards, Jernej > > > > + > > > + osc24M: osc24M-clk { > > > + #clock-cells = <0>; > > > + compatible = "fixed-clock"; > > > + clock-frequency = <24000000>; > > > + clock-output-names = "osc24M"; > > > + }; > > > + > > > + pmu { > > > + compatible = "arm,cortex-a53-pmu"; > > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > > > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > > > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > > > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > > > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > > > + }; > > > + > > > + psci { > > > + compatible = "arm,psci-0.2"; > > > + method = "smc"; > > > + }; > > > + > > > + timer { > > > + compatible = "arm,armv8-timer"; > > > + arm,no-tick-in-suspend; > > > + interrupts = <GIC_PPI 13 > > > + (GIC_CPU_MASK_SIMPLE(4) | > > > > IRQ_TYPE_LEVEL_HIGH)>, > > > > > + <GIC_PPI 14 > > > + (GIC_CPU_MASK_SIMPLE(4) | > > > > IRQ_TYPE_LEVEL_HIGH)>, > > > > > + <GIC_PPI 11 > > > + (GIC_CPU_MASK_SIMPLE(4) | > > > > IRQ_TYPE_LEVEL_HIGH)>, > > > > > + <GIC_PPI 10 > > > + (GIC_CPU_MASK_SIMPLE(4) | > > > > IRQ_TYPE_LEVEL_HIGH)>; > > > > > + }; > > > > Vendor kernel sets IRQ to low level. What is the difference? > > Nothing, really. The polarity of SPI level IRQ lines is hardwired at > integration time, both at the peripheral and the GIC distributor. The > GIC software interface has no register to control that - all you can > configure is edge or level. There *is* some underlying polarity, but to > my understanding this is just mentioned here for completeness, and > because the binding requires to name one. > > > > + > > > + soc@0 { > > > + compatible = "simple-bus"; > > > + #address-cells = <1>; > > > + #size-cells = <1>; > > > + ranges = <0x0 0x0 0x0 0x40000000>; > > > + > > > + syscon: syscon@3000000 { > > > + compatible = "allwinner,sun50i-h616-system- > > > > control"; > > > > > + reg = <0x03000000 0x1000>; > > > + #address-cells = <1>; > > > + #size-cells = <1>; > > > + ranges; > > > + > > > + sram_c: sram@28000 { > > > + compatible = "mmio-sram"; > > > + reg = <0x00028000 0x30000>; > > > + #address-cells = <1>; > > > + #size-cells = <1>; > > > + ranges = <0 0x00028000 0x30000>; > > > + }; > > > + }; > > > + > > > + ccu: clock@3001000 { > > > + compatible = "allwinner,sun50i-h616-ccu"; > > > + reg = <0x03001000 0x1000>; > > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > > > + clock-names = "hosc", "losc", "iosc"; > > > + #clock-cells = <1>; > > > + #reset-cells = <1>; > > > + }; > > > + > > > + watchdog: watchdog@30090a0 { > > > + compatible = "allwinner,sun50i-h616-wdt", > > > + "allwinner,sun6i-a31-wdt"; > > > + reg = <0x030090a0 0x20>; > > > + interrupts = <GIC_SPI 50 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&osc24M>; > > > + }; > > > + > > > + pio: pinctrl@300b000 { > > > + compatible = "allwinner,sun50i-h616- pinctrl"; > > > + reg = <0x0300b000 0x400>; > > > + interrupts = <GIC_SPI 51 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 52 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 53 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 43 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 54 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 55 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 56 > > > > IRQ_TYPE_LEVEL_HIGH>, > > > > > + <GIC_SPI 57 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc > > > > 0>; > > > > > + clock-names = "apb", "hosc", "losc"; > > > + gpio-controller; > > > + #gpio-cells = <3>; > > > + interrupt-controller; > > > + #interrupt-cells = <3>; > > > + > > > + ext_rgmii_pins: rgmii-pins { > > > + pins = "PI0", "PI1", "PI2", "PI3", > > > > "PI4", > > > > > + "PI5", "PI7", "PI8", "PI9", > > > > "PI10", > > > > > + "PI11", "PI12", "PI13", > > > > "PI14", "PI15", > > > > > + "PI16"; > > > + function = "emac0"; > > > + drive-strength = <40>; > > > + }; > > > + > > > + i2c0_pins: i2c0-pins { > > > + pins = "PI6", "PI7"; > > > + function = "i2c0"; > > > + }; > > > + > > > + i2c3_ph_pins: i2c3-ph-pins { > > > + pins = "PH4", "PH5"; > > > + function = "i2c3"; > > > + }; > > > + > > > + ir_rx_pin: ir-rx-pin { > > > + pins = "PH10"; > > > + function = "ir_rx"; > > > + }; > > > + > > > + mmc0_pins: mmc0-pins { > > > + pins = "PF0", "PF1", "PF2", "PF3", > > > + "PF4", "PF5"; > > > + function = "mmc0"; > > > + drive-strength = <30>; > > > + bias-pull-up; > > > + }; > > > + > > > + mmc1_pins: mmc1-pins { > > > + pins = "PG0", "PG1", "PG2", "PG3", > > > + "PG4", "PG5"; > > > + function = "mmc1"; > > > + drive-strength = <30>; > > > + bias-pull-up; > > > + }; > > > + > > > + mmc2_pins: mmc2-pins { > > > + pins = "PC0", "PC1", "PC5", "PC6", > > > + "PC8", "PC9", "PC10", > > > > "PC11", > > > > > + "PC13", "PC14", "PC15", > > > > "PC16"; > > > > > + function = "mmc2"; > > > + drive-strength = <30>; > > > + bias-pull-up; > > > + }; > > > + > > > + spi0_pins: spi0-pins { > > > + pins = "PC0", "PC2", "PC3", "PC4"; > > > + function = "spi0"; > > > + }; > > > + > > > + spi1_pins: spi1-pins { > > > + pins = "PH6", "PH7", "PH8"; > > > + function = "spi1"; > > > + }; > > > + > > > + spi1_cs_pin: spi1-cs-pin { > > > + pins = "PH5"; > > > + function = "spi1"; > > > + }; > > > + > > > + uart0_ph_pins: uart0-ph-pins { > > > + pins = "PH0", "PH1"; > > > + function = "uart0"; > > > + }; > > > + > > > + uart1_pins: uart1-pins { > > > + pins = "PG6", "PG7"; > > > + function = "uart1"; > > > + }; > > > + > > > + uart1_rts_cts_pins: uart1-rts-cts-pins { > > > + pins = "PG8", "PG9"; > > > + function = "uart1"; > > > + }; > > > > Please add /omit-if-no-ref/ where applicable. > > OK. I think most boards have Bluetooth at UART1, though. > > > > + }; > > > + > > > + gic: interrupt-controller@3021000 { > > > + compatible = "arm,gic-400"; > > > + reg = <0x03021000 0x1000>, > > > + <0x03022000 0x2000>, > > > + <0x03024000 0x2000>, > > > + <0x03026000 0x2000>; > > > + interrupts = <GIC_PPI 9 > > > > (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > > > > > + interrupt-controller; > > > + #interrupt-cells = <3>; > > > + }; > > > + > > > + mmc0: mmc@4020000 { > > > + compatible = "allwinner,sun50i-h616-mmc", > > > + "allwinner,sun50i-a100- mmc"; > > > + reg = <0x04020000 0x1000>; > > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu > > > > CLK_MMC0>; > > > > > + clock-names = "ahb", "mmc"; > > > + resets = <&ccu RST_BUS_MMC0>; > > > + reset-names = "ahb"; > > > + interrupts = <GIC_SPI 35 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&mmc0_pins>; > > > + status = "disabled"; > > > + max-frequency = <150000000>; > > > + cap-sd-highspeed; > > > + cap-mmc-highspeed; > > > + mmc-ddr-3_3v; > > > + cap-sdio-irq; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + mmc1: mmc@4021000 { > > > + compatible = "allwinner,sun50i-h616-mmc", > > > + "allwinner,sun50i-a100- mmc"; > > > + reg = <0x04021000 0x1000>; > > > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu > > > > CLK_MMC1>; > > > > > + clock-names = "ahb", "mmc"; > > > + resets = <&ccu RST_BUS_MMC1>; > > > + reset-names = "ahb"; > > > + interrupts = <GIC_SPI 36 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&mmc1_pins>; > > > + status = "disabled"; > > > + max-frequency = <150000000>; > > > + cap-sd-highspeed; > > > + cap-mmc-highspeed; > > > + mmc-ddr-3_3v; > > > + cap-sdio-irq; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + mmc2: mmc@4022000 { > > > + compatible = "allwinner,sun50i-h616-emmc", > > > + "allwinner,sun50i-a100- emmc"; > > > + reg = <0x04022000 0x1000>; > > > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu > > > > CLK_MMC2>; > > > > > + clock-names = "ahb", "mmc"; > > > + resets = <&ccu RST_BUS_MMC2>; > > > + reset-names = "ahb"; > > > + interrupts = <GIC_SPI 37 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&mmc2_pins>; > > > + status = "disabled"; > > > + max-frequency = <150000000>; > > > + cap-sd-highspeed; > > > + cap-mmc-highspeed; > > > + mmc-ddr-3_3v; > > > + cap-sdio-irq; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + uart0: serial@5000000 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05000000 0x400>; > > > + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART0>; > > > + resets = <&ccu RST_BUS_UART0>; > > > + status = "disabled"; > > > + }; > > > + > > > + uart1: serial@5000400 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05000400 0x400>; > > > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART1>; > > > + resets = <&ccu RST_BUS_UART1>; > > > + status = "disabled"; > > > + }; > > > + > > > + uart2: serial@5000800 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05000800 0x400>; > > > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART2>; > > > + resets = <&ccu RST_BUS_UART2>; > > > + status = "disabled"; > > > + }; > > > + > > > + uart3: serial@5000c00 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05000c00 0x400>; > > > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART3>; > > > + resets = <&ccu RST_BUS_UART3>; > > > + status = "disabled"; > > > + }; > > > + > > > + uart4: serial@5001000 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05001000 0x400>; > > > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART4>; > > > + resets = <&ccu RST_BUS_UART4>; > > > + status = "disabled"; > > > + }; > > > + > > > + uart5: serial@5001400 { > > > + compatible = "snps,dw-apb-uart"; > > > + reg = <0x05001400 0x400>; > > > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > > > + reg-shift = <2>; > > > + reg-io-width = <4>; > > > + clocks = <&ccu CLK_BUS_UART5>; > > > + resets = <&ccu RST_BUS_UART5>; > > > + status = "disabled"; > > > + }; > > > + > > > + i2c0: i2c@5002000 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x05002000 0x400>; > > > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&ccu CLK_BUS_I2C0>; > > > + resets = <&ccu RST_BUS_I2C0>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&i2c0_pins>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + i2c1: i2c@5002400 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x05002400 0x400>; > > > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&ccu CLK_BUS_I2C1>; > > > + resets = <&ccu RST_BUS_I2C1>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + i2c2: i2c@5002800 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x05002800 0x400>; > > > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&ccu CLK_BUS_I2C2>; > > > + resets = <&ccu RST_BUS_I2C2>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + i2c3: i2c@5002c00 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x05002c00 0x400>; > > > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&ccu CLK_BUS_I2C3>; > > > + resets = <&ccu RST_BUS_I2C3>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + i2c4: i2c@5003000 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x05003000 0x400>; > > > + interrupts = <GIC_SPI 10 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&ccu CLK_BUS_I2C4>; > > > + resets = <&ccu RST_BUS_I2C4>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + spi0: spi@5010000 { > > > + compatible = "allwinner,sun50i-h616-spi", > > > + "allwinner,sun8i-h3-spi"; > > > + reg = <0x05010000 0x1000>; > > > + interrupts = <GIC_SPI 12 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu > > > > CLK_SPI0>; > > > > > + clock-names = "ahb", "mod"; > > > + resets = <&ccu RST_BUS_SPI0>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&spi0_pins>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + spi1: spi@5011000 { > > > + compatible = "allwinner,sun50i-h616-spi", > > > + "allwinner,sun8i-h3-spi"; > > > + reg = <0x05011000 0x1000>; > > > + interrupts = <GIC_SPI 13 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu > > > > CLK_SPI1>; > > > > > + clock-names = "ahb", "mod"; > > > + resets = <&ccu RST_BUS_SPI1>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&spi1_pins>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + emac0: ethernet@5020000 { > > > + compatible = "allwinner,sun50i-h616-emac", > > > + "allwinner,sun50i-a64- emac"; > > > + syscon = <&syscon>; > > > + reg = <0x05020000 0x10000>; > > > + interrupts = <GIC_SPI 14 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + interrupt-names = "macirq"; > > > + resets = <&ccu RST_BUS_EMAC0>; > > > + reset-names = "stmmaceth"; > > > + clocks = <&ccu CLK_BUS_EMAC0>; > > > + clock-names = "stmmaceth"; > > > + status = "disabled"; > > > + > > > + mdio0: mdio { > > > + compatible = "snps,dwmac-mdio"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + }; > > > + > > > + rtc: rtc@7000000 { > > > + compatible = "allwinner,sun50i-h616-rtc"; > > > + reg = <0x07000000 0x400>; > > > + interrupts = <GIC_SPI 101 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > Above interrupt doesn't seem to be correct according to documentation. It > > should be 104. > > That is a very good catch, 101/133 is indeed the RTC IRQ number on the > H6. > > > > + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>, > > > + <&ccu CLK_PLL_SYSTEM_32K>; > > > + clock-names = "bus", "hosc", > > > + "pll-32k"; > > > + clock-output-names = "osc32k", "osc32k- out", > > > > "iosc"; > > > > > + #clock-cells = <1>; > > > + }; > > > + > > > + r_ccu: clock@7010000 { > > > + compatible = "allwinner,sun50i-h616-r-ccu"; > > > + reg = <0x07010000 0x210>; > > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > > > + <&ccu CLK_PLL_PERIPH0>; > > > + clock-names = "hosc", "losc", "iosc", "pll- > > > > periph"; > > > > > + #clock-cells = <1>; > > > + #reset-cells = <1>; > > > + }; > > > + > > > + r_pio: pinctrl@7022000 { > > > + compatible = "allwinner,sun50i-h616-r- > > > > pinctrl"; > > > > > + reg = <0x07022000 0x400>; > > > + interrupts = <GIC_SPI 43 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > Above interrupt is already used for port E in first pinctrl. Is this > > shared > > somehow? > > Huh, another good find. The manual does not seem to mention a GPIO_L > interrupt, and the two PL pins do not report function 6. > when probing the registers in U-Boot there are no other pins (neither in > PortL nor PortM), also the interrupt registers (@+0x200) are not > implemented. So there does not seem to be an interrupt. > > The pinctrl driver does not seem to care (by looking at the code, > and by booting it), as .irq_banks is 0, so no IRQ controller > functionality is ever instantiated. > The binding makes the interrupts property mandatory, though, so this > needs to be amended there. > > > I will try to post a new version till the end of the week. > > Thanks! > Andre > > > Best regards, > > Jernej > > > > > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, > > > > <&rtc 0>; > > > > > + clock-names = "apb", "hosc", "losc"; > > > + gpio-controller; > > > + #gpio-cells = <3>; > > > + interrupt-controller; > > > + #interrupt-cells = <3>; > > > + > > > + r_i2c_pins: r-i2c-pins { > > > + pins = "PL0", "PL1"; > > > + function = "s_i2c"; > > > + }; > > > + > > > + r_rsb_pins: r-rsb-pins { > > > + pins = "PL0", "PL1"; > > > + function = "s_rsb"; > > > + }; > > > + }; > > > + > > > + ir: ir@7040000 { > > > + compatible = "allwinner,sun50i-h616-ir", > > > + "allwinner,sun6i-a31-ir"; > > > + reg = <0x07040000 0x400>; > > > + interrupts = <GIC_SPI 106 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&r_ccu CLK_R_APB1_IR>, > > > + <&r_ccu CLK_IR>; > > > + clock-names = "apb", "ir"; > > > + resets = <&r_ccu RST_R_APB1_IR>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&ir_rx_pin>; > > > + status = "disabled"; > > > + }; > > > + > > > + r_i2c: i2c@7081400 { > > > + compatible = "allwinner,sun50i-h616-i2c", > > > + "allwinner,sun6i-a31-i2c"; > > > + reg = <0x07081400 0x400>; > > > + interrupts = <GIC_SPI 105 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&r_ccu CLK_R_APB2_I2C>; > > > + resets = <&r_ccu RST_R_APB2_I2C>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + > > > + r_rsb: rsb@7083000 { > > > + compatible = "allwinner,sun50i-h616-rsb", > > > + "allwinner,sun8i-a23-rsb"; > > > + reg = <0x07083000 0x400>; > > > + interrupts = <GIC_SPI 109 > > > > IRQ_TYPE_LEVEL_HIGH>; > > > > > + clocks = <&r_ccu CLK_R_APB2_RSB>; > > > + clock-frequency = <3000000>; > > > + resets = <&r_ccu RST_R_APB2_RSB>; > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&r_rsb_pins>; > > > + status = "disabled"; > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + }; > > > + }; > > > +};
On Sat, 02 Jul 2022 23:16:53 +0200 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, > Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > > On Tue, 03 May 2022 21:05:11 +0200 > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > Hi Jernej, > > > > many thanks for taking the time to wade through this file! > > > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > > > > This (relatively) new SoC is similar to the H6, but drops the (broken) > > > > PCIe support and the USB 3.0 controller. It also gets the management > > > > controller removed, which in turn removes *some*, but not all of the > > > > devices formerly dedicated to the ARISC (CPUS). > > > > And while there is still the extra sunxi interrupt controller, the > > > > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > > > > > > > The reserved memory node is actually handled by Trusted Firmware now, > > > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > > > keep it in here for now, until U-Boot learns to do this properly. > > > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > > --- > > > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > > > > 1 file changed, 574 insertions(+) > > > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > b/arch/arm64/ > > > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > new file mode 100644 > > > > index 000000000000..cc06cdd15ba5 > > > > --- /dev/null > > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > @@ -0,0 +1,574 @@ > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > > +// Copyright (C) 2020 Arm Ltd. > > > > +// based on the H6 dtsi, which is: > > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > + > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > > + > > > > +/ { > > > > + interrupt-parent = <&gic>; > > > > + #address-cells = <2>; > > > > + #size-cells = <2>; > > > > + > > > > + cpus { > > > > + #address-cells = <1>; > > > > + #size-cells = <0>; > > > > + > > > > + cpu0: cpu@0 { > > > > + compatible = "arm,cortex-a53"; > > > > + device_type = "cpu"; > > > > + reg = <0>; > > > > + enable-method = "psci"; > > > > + clocks = <&ccu CLK_CPUX>; > > > > + }; > > > > + > > > > + cpu1: cpu@1 { > > > > + compatible = "arm,cortex-a53"; > > > > + device_type = "cpu"; > > > > + reg = <1>; > > > > + enable-method = "psci"; > > > > + clocks = <&ccu CLK_CPUX>; > > > > + }; > > > > + > > > > + cpu2: cpu@2 { > > > > + compatible = "arm,cortex-a53"; > > > > + device_type = "cpu"; > > > > + reg = <2>; > > > > + enable-method = "psci"; > > > > + clocks = <&ccu CLK_CPUX>; > > > > + }; > > > > + > > > > + cpu3: cpu@3 { > > > > + compatible = "arm,cortex-a53"; > > > > + device_type = "cpu"; > > > > + reg = <3>; > > > > + enable-method = "psci"; > > > > + clocks = <&ccu CLK_CPUX>; > > > > + }; > > > > + }; > > > > + > > > > + reserved-memory { > > > > + #address-cells = <2>; > > > > + #size-cells = <2>; > > > > + ranges; > > > > + > > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > > > + secmon_reserved: secmon@40000000 { > > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > > + no-map; > > > > + }; > > > > + }; > > > > > > I'm not a fan of above. If anything changes in future in BL31, U-Boot > > > would > > > need to reconfigure it anyway. Can we just skip it? > > > > I am not a fan neither, but last time I checked this is needed to boot. > > Indeed TF-A inserts this node, with the right values, into U-Boot's DT. > > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > > the kernel as well. > > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > > U-Boot fails to propagate the /reserved-memory node into that copy. > > There does not seem to be a global notion of reserved memory in U-Boot. > > Some commands (like tftp) explicitly parse the control DT to find and > > respect reserved memory regions. bootm does that also, but only to > > avoid placing the ramdisk or DTB into reserved memory. The information > > ends up in images->lmb, but is not used to generate or amend nodes in > > the target DT. > > So the bits and pieces are there, but it will require some code to be > > added to the generic U-Boot code. > > > > So what do you think? Leaving this out will prevent loading DTBs into > > U-Boot, at the moment, which sounds bad. I suggest we keep it in, for > > now, it should not really hurt. U-Boot will hopefully start to do the > > right thing soon, then we can either phase it out here (maybe when we > > actually change something in TF-A), or let U-Boot fix it. > > TBH, if "soon" is really soon, I would rather wait with H616 DT until U-Boot > supports carrying over reserved memory nodes. But this also carries compatibility issues. U-Boot support the H616 for more than a year now, and the earliest possible U-Boot release having that propagation code would be the one released in October. And then people would still need to update first, so that's quite some months out. And I was actually hoping to get at least the H616 DT patches off my plate, and get them into the tree to have a stable and agreed upon base (before this series turns into a teenager ;-) Then we could for instance update the U-Boot H616 support. > Whatever we do now, it will have > compatibility issues. If we introduce reserved memory node now, we can't > easily drop it later. Bootloaders are not very often updated, but kernels and > DTB files are, at least in my experience. So when we decide to drop the node? I think of the three possibilities: - Drop the node now, and ask people to not load DTBs explicitly - Drop the node when U-Boot learned to propagate the reservation - Keep the node the last one is the least painful: having this node in does not really hurt, so we can be very relaxed with this removal decision: - If U-Boot does not add the reserved node, we are covered. - If U-Boot adds the node, it will do so in a way where it deals with existing reservations. So either it doesn't actually change anything, or it extends the reservation. - Should the TF-A location actually move (and we have no plans or needs to do that), people would only get this by updating the firmware, at which point the U-Boot part would surely be in place already. We don't really support updating just BL31 in an existing binary firmware image, so you would get an updated U-Boot as well. I think the worst case scenario is that users end up with an unneeded 512K reservation. If they care, a firmware update should solve this problem. As for the time to remove that node: we could do that at the time when (or rather: if) we actually change the TF-A reservation. At the moment there are no plans to do this, and the size reservation is more than generous (the current debug build is actually 77 KB or so only). If there is no change, and the node stays in the .dtsi, it doesn't really hurt, see above. > After 10 years? Alternatively, reserved memory node can be just dropped and > anyone loading DTB file from outside would need to make sure it's patched. But > that's unexpected from user perspective, although patching DT files is done by > some distros. Yeah, let's not go there. As you know, I already dislike the idea of explicitly loading DTBs at all, but I understand this is what people, and distributions, do, so I'd rather have them covered. Hence the node to work with existing firmware. Does that make sense? Cheers, Andre
Dne ponedeljek, 04. julij 2022 ob 15:30:57 CEST je Andre Przywara napisal(a): > On Sat, 02 Jul 2022 23:16:53 +0200 > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > Hi Jernej, > > > Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > > > On Tue, 03 May 2022 21:05:11 +0200 > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > Hi Jernej, > > > > > > many thanks for taking the time to wade through this file! > > > > > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > > > > > This (relatively) new SoC is similar to the H6, but drops the (broken) > > > > > PCIe support and the USB 3.0 controller. It also gets the management > > > > > controller removed, which in turn removes *some*, but not all of the > > > > > devices formerly dedicated to the ARISC (CPUS). > > > > > And while there is still the extra sunxi interrupt controller, the > > > > > package lacks the corresponding NMI pin, so no interrupts for the PMIC. > > > > > > > > > > The reserved memory node is actually handled by Trusted Firmware now, > > > > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > > > > keep it in here for now, until U-Boot learns to do this properly. > > > > > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > > > --- > > > > > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 +++++++++++++++ +++ > > > > > 1 file changed, 574 insertions(+) > > > > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > b/arch/arm64/ > > > > > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > new file mode 100644 > > > > > index 000000000000..cc06cdd15ba5 > > > > > --- /dev/null > > > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > @@ -0,0 +1,574 @@ > > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > > > +// Copyright (C) 2020 Arm Ltd. > > > > > +// based on the H6 dtsi, which is: > > > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > > + > > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > > > + > > > > > +/ { > > > > > + interrupt-parent = <&gic>; > > > > > + #address-cells = <2>; > > > > > + #size-cells = <2>; > > > > > + > > > > > + cpus { > > > > > + #address-cells = <1>; > > > > > + #size-cells = <0>; > > > > > + > > > > > + cpu0: cpu@0 { > > > > > + compatible = "arm,cortex-a53"; > > > > > + device_type = "cpu"; > > > > > + reg = <0>; > > > > > + enable-method = "psci"; > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > + }; > > > > > + > > > > > + cpu1: cpu@1 { > > > > > + compatible = "arm,cortex-a53"; > > > > > + device_type = "cpu"; > > > > > + reg = <1>; > > > > > + enable-method = "psci"; > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > + }; > > > > > + > > > > > + cpu2: cpu@2 { > > > > > + compatible = "arm,cortex-a53"; > > > > > + device_type = "cpu"; > > > > > + reg = <2>; > > > > > + enable-method = "psci"; > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > + }; > > > > > + > > > > > + cpu3: cpu@3 { > > > > > + compatible = "arm,cortex-a53"; > > > > > + device_type = "cpu"; > > > > > + reg = <3>; > > > > > + enable-method = "psci"; > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > + }; > > > > > + }; > > > > > + > > > > > + reserved-memory { > > > > > + #address-cells = <2>; > > > > > + #size-cells = <2>; > > > > > + ranges; > > > > > + > > > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > > > > + secmon_reserved: secmon@40000000 { > > > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > > > + no-map; > > > > > + }; > > > > > + }; > > > > > > > > I'm not a fan of above. If anything changes in future in BL31, U-Boot > > > > would > > > > need to reconfigure it anyway. Can we just skip it? > > > > > > I am not a fan neither, but last time I checked this is needed to boot. > > > Indeed TF-A inserts this node, with the right values, into U-Boot's DT. > > > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > > > the kernel as well. > > > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > > > U-Boot fails to propagate the /reserved-memory node into that copy. > > > There does not seem to be a global notion of reserved memory in U-Boot. > > > Some commands (like tftp) explicitly parse the control DT to find and > > > respect reserved memory regions. bootm does that also, but only to > > > avoid placing the ramdisk or DTB into reserved memory. The information > > > ends up in images->lmb, but is not used to generate or amend nodes in > > > the target DT. > > > So the bits and pieces are there, but it will require some code to be > > > added to the generic U-Boot code. > > > > > > So what do you think? Leaving this out will prevent loading DTBs into > > > U-Boot, at the moment, which sounds bad. I suggest we keep it in, for > > > now, it should not really hurt. U-Boot will hopefully start to do the > > > right thing soon, then we can either phase it out here (maybe when we > > > actually change something in TF-A), or let U-Boot fix it. > > > > TBH, if "soon" is really soon, I would rather wait with H616 DT until U- Boot > > supports carrying over reserved memory nodes. > > But this also carries compatibility issues. U-Boot support the H616 for > more than a year now, and the earliest possible U-Boot release having that > propagation code would be the one released in October. I was hoping you would say July (next U-Boot release) :). > And then people > would still need to update first, so that's quite some months out. > And I was actually hoping to get at least the H616 DT patches off my > plate, and get them into the tree to have a stable and agreed upon base > (before this series turns into a teenager ;-) Yeah, I would like that too. > Then we could for instance update the U-Boot H616 support. > > > Whatever we do now, it will have > > compatibility issues. If we introduce reserved memory node now, we can't > > easily drop it later. Bootloaders are not very often updated, but kernels and > > DTB files are, at least in my experience. So when we decide to drop the node? > > I think of the three possibilities: > - Drop the node now, and ask people to not load DTBs explicitly > - Drop the node when U-Boot learned to propagate the reservation > - Keep the node > the last one is the least painful: having this node in does not really > hurt, so we can be very relaxed with this removal decision: > - If U-Boot does not add the reserved node, we are covered. > - If U-Boot adds the node, it will do so in a way where it deals with > existing reservations. So either it doesn't actually change anything, or > it extends the reservation. > - Should the TF-A location actually move (and we have no plans or needs to > do that), people would only get this by updating the firmware, at which > point the U-Boot part would surely be in place already. We don't really > support updating just BL31 in an existing binary firmware image, so you > would get an updated U-Boot as well. > > I think the worst case scenario is that users end up with an unneeded 512K > reservation. If they care, a firmware update should solve this problem. > > As for the time to remove that node: we could do that at the time when > (or rather: if) we actually change the TF-A reservation. At the moment > there are no plans to do this, and the size reservation is more than > generous (the current debug build is actually 77 KB or so only). If there > is no change, and the node stays in the .dtsi, it doesn't really hurt, see > above. I see your point, but I would like to get some input from Samuel first. Samuel, what do you think? > > > After 10 years? Alternatively, reserved memory node can be just dropped and > > anyone loading DTB file from outside would need to make sure it's patched. But > > that's unexpected from user perspective, although patching DT files is done by > > some distros. > > Yeah, let's not go there. As you know, I already dislike the idea of > explicitly loading DTBs at all, but I understand this is what people, and > distributions, do, so I'd rather have them covered. Hence the node to > work with existing firmware. Reusing DTB from U-Boot is only useful when you're happy with completeness of DT and with the lack of bugs in it. Then you can save troubles with skipping external DTB load step and life is easier. But as you know, features and thus nodes are added in steps and sometimes some bugs are fixed, which means it's extremely handy to have easily updatable DTB file. Yes, U-Boot can be automated, but it's tedious for distro to maintain one bootloader package per board. Ideally, distro shouldn't care at all about that, but many boards don't have designated bootloader storage (SPI NOR flash in AW case), so they have to be combined on same storage, partition even, as distro. On the other hand, when building kernel, you automatically build all relevant DTB files, which you can then just copy to common place. No device specific handling needed. Also, U-Boot doesn't sync DT files every release, so latest U-Boot doesn't necessarly mean latest DT. Above is a bit off topic, but I hope you understand why distros opt to use external DTB files (speaking from my own experiences). Best regards, Jernej > > Does that make sense? > > Cheers, > Andre >
Hi Andre, On 7/4/22 8:30 AM, Andre Przywara wrote: > On Sat, 02 Jul 2022 23:16:53 +0200 > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: >> Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): >>> On Tue, 03 May 2022 21:05:11 +0200 >>> Jernej Škrabec <jernej.skrabec@gmail.com> wrote: >>>> Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): >>>>> This (relatively) new SoC is similar to the H6, but drops the (broken) >>>>> PCIe support and the USB 3.0 controller. It also gets the management >>>>> controller removed, which in turn removes *some*, but not all of the >>>>> devices formerly dedicated to the ARISC (CPUS). >>>>> And while there is still the extra sunxi interrupt controller, the >>>>> package lacks the corresponding NMI pin, so no interrupts for the PMIC. >>>>> >>>>> The reserved memory node is actually handled by Trusted Firmware now, >>>>> but U-Boot fails to propagate this to a separately loaded DTB, so we >>>>> keep it in here for now, until U-Boot learns to do this properly. >>>>> >>>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com> >>>>> --- >>>>> >>>>> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ >>>>> 1 file changed, 574 insertions(+) >>>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi >>>>> >>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi >>>>> b/arch/arm64/ >>>> >>>> boot/dts/allwinner/sun50i-h616.dtsi >>>> >>>>> new file mode 100644 >>>>> index 000000000000..cc06cdd15ba5 >>>>> --- /dev/null >>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi >>>>> @@ -0,0 +1,574 @@ >>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>>>> +// Copyright (C) 2020 Arm Ltd. >>>>> +// based on the H6 dtsi, which is: >>>>> +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> >>>>> + >>>>> +#include <dt-bindings/interrupt-controller/arm-gic.h> >>>>> +#include <dt-bindings/clock/sun50i-h616-ccu.h> >>>>> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> >>>>> +#include <dt-bindings/reset/sun50i-h616-ccu.h> >>>>> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> >>>>> + >>>>> +/ { >>>>> + interrupt-parent = <&gic>; >>>>> + #address-cells = <2>; >>>>> + #size-cells = <2>; >>>>> + >>>>> + cpus { >>>>> + #address-cells = <1>; >>>>> + #size-cells = <0>; >>>>> + >>>>> + cpu0: cpu@0 { >>>>> + compatible = "arm,cortex-a53"; >>>>> + device_type = "cpu"; >>>>> + reg = <0>; >>>>> + enable-method = "psci"; >>>>> + clocks = <&ccu CLK_CPUX>; >>>>> + }; >>>>> + >>>>> + cpu1: cpu@1 { >>>>> + compatible = "arm,cortex-a53"; >>>>> + device_type = "cpu"; >>>>> + reg = <1>; >>>>> + enable-method = "psci"; >>>>> + clocks = <&ccu CLK_CPUX>; >>>>> + }; >>>>> + >>>>> + cpu2: cpu@2 { >>>>> + compatible = "arm,cortex-a53"; >>>>> + device_type = "cpu"; >>>>> + reg = <2>; >>>>> + enable-method = "psci"; >>>>> + clocks = <&ccu CLK_CPUX>; >>>>> + }; >>>>> + >>>>> + cpu3: cpu@3 { >>>>> + compatible = "arm,cortex-a53"; >>>>> + device_type = "cpu"; >>>>> + reg = <3>; >>>>> + enable-method = "psci"; >>>>> + clocks = <&ccu CLK_CPUX>; >>>>> + }; >>>>> + }; >>>>> + >>>>> + reserved-memory { >>>>> + #address-cells = <2>; >>>>> + #size-cells = <2>; >>>>> + ranges; >>>>> + >>>>> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ >>>>> + secmon_reserved: secmon@40000000 { >>>>> + reg = <0x0 0x40000000 0x0 0x80000>; >>>>> + no-map; >>>>> + }; >>>>> + }; >>>> >>>> I'm not a fan of above. If anything changes in future in BL31, U-Boot >>>> would >>>> need to reconfigure it anyway. Can we just skip it? >>> >>> I am not a fan neither, but last time I checked this is needed to boot. >>> Indeed TF-A inserts this node, with the right values, into U-Boot's DT. >>> And that's nicely preserved if you use that DT ($fdtcontroladdr) for >>> the kernel as well. >>> But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then >>> U-Boot fails to propagate the /reserved-memory node into that copy. >>> There does not seem to be a global notion of reserved memory in U-Boot. >>> Some commands (like tftp) explicitly parse the control DT to find and >>> respect reserved memory regions. bootm does that also, but only to >>> avoid placing the ramdisk or DTB into reserved memory. The information >>> ends up in images->lmb, but is not used to generate or amend nodes in >>> the target DT. >>> So the bits and pieces are there, but it will require some code to be >>> added to the generic U-Boot code. >>> >>> So what do you think? Leaving this out will prevent loading DTBs into >>> U-Boot, at the moment, which sounds bad. I suggest we keep it in, for >>> now, it should not really hurt. U-Boot will hopefully start to do the >>> right thing soon, then we can either phase it out here (maybe when we >>> actually change something in TF-A), or let U-Boot fix it. >> >> TBH, if "soon" is really soon, I would rather wait with H616 DT until U-Boot >> supports carrying over reserved memory nodes. > > But this also carries compatibility issues. U-Boot support the H616 for > more than a year now, and the earliest possible U-Boot release having that > propagation code would be the one released in October. And then people > would still need to update first, so that's quite some months out. > And I was actually hoping to get at least the H616 DT patches off my > plate, and get them into the tree to have a stable and agreed upon base > (before this series turns into a teenager ;-) > Then we could for instance update the U-Boot H616 support. There is no compatibility issue here if people are using $fdtcontroladdr. >> Whatever we do now, it will have >> compatibility issues. If we introduce reserved memory node now, we can't >> easily drop it later. Bootloaders are not very often updated, but kernels and >> DTB files are, at least in my experience. So when we decide to drop the node? > > I think of the three possibilities: > - Drop the node now, and ask people to not load DTBs explicitly This is my preferred solution. My position has always been that the devicetree is provided by platform firmware, not the OS. The only reason for even submitting the devicetree to Linux is because that is the location of the bindings and validation tooling. I have been using this approach for D1, and so far there have been no unsolvable problems. Yes, most image builders assume you want to load a DTB from disk, but teaching them not to do that is fairly simple. And yes, it means we have to do better about keeping the U-Boot DTSs in sync, but I think we can manage that. > - Drop the node when U-Boot learned to propagate the reservation > - Keep the node > the last one is the least painful: having this node in does not really > hurt, so we can be very relaxed with this removal decision: Supporting explicitly-loaded DTBs is the most painful option going forward, because that means U-Boot has to know about and propagate _every_ runtime change made by any firmware component (not just changes made by it) to the control FDT. For example, consider TF-A patching in information about idle states, or SID contents in secure mode, or marking nodes as "reserved" because it delegates those devices to a secure enclave. This problem is solved if we say "we support $fdtcontroladdr, and we support overlays; but you are on your own if you load a DTB from disk." Distros will continue loading DTBs from disk as long as it sorta-kinda-mostly works, and then years later users will complain that their phone uses 4 watts at idle, because their explicitly-loaded DTB contained idle states that their firmware did not support (this is a true story). "Don't load DTBs" is a much easier story to tell if doing so is obviously broken out of the box from day 1. Regards, Samuel > - If U-Boot does not add the reserved node, we are covered. > - If U-Boot adds the node, it will do so in a way where it deals with > existing reservations. So either it doesn't actually change anything, or > it extends the reservation. > - Should the TF-A location actually move (and we have no plans or needs to > do that), people would only get this by updating the firmware, at which > point the U-Boot part would surely be in place already. We don't really > support updating just BL31 in an existing binary firmware image, so you > would get an updated U-Boot as well. > > I think the worst case scenario is that users end up with an unneeded 512K > reservation. If they care, a firmware update should solve this problem. > > As for the time to remove that node: we could do that at the time when > (or rather: if) we actually change the TF-A reservation. At the moment > there are no plans to do this, and the size reservation is more than > generous (the current debug build is actually 77 KB or so only). If there > is no change, and the node stays in the .dtsi, it doesn't really hurt, see > above. > >> After 10 years? Alternatively, reserved memory node can be just dropped and >> anyone loading DTB file from outside would need to make sure it's patched. But >> that's unexpected from user perspective, although patching DT files is done by >> some distros. > > Yeah, let's not go there. As you know, I already dislike the idea of > explicitly loading DTBs at all, but I understand this is what people, and > distributions, do, so I'd rather have them covered. Hence the node to > work with existing firmware. > > Does that make sense? > > Cheers, > Andre >
On Mon, 4 Jul 2022 13:44:18 -0500 Samuel Holland <samuel@sholland.org> wrote: Hi Samuel, > On 7/4/22 8:30 AM, Andre Przywara wrote: > > On Sat, 02 Jul 2022 23:16:53 +0200 > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > >> Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > >>> On Tue, 03 May 2022 21:05:11 +0200 > >>> Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > >>>> Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a): > >>>>> This (relatively) new SoC is similar to the H6, but drops the (broken) > >>>>> PCIe support and the USB 3.0 controller. It also gets the management > >>>>> controller removed, which in turn removes *some*, but not all of the > >>>>> devices formerly dedicated to the ARISC (CPUS). > >>>>> And while there is still the extra sunxi interrupt controller, the > >>>>> package lacks the corresponding NMI pin, so no interrupts for the PMIC. > >>>>> > >>>>> The reserved memory node is actually handled by Trusted Firmware now, > >>>>> but U-Boot fails to propagate this to a separately loaded DTB, so we > >>>>> keep it in here for now, until U-Boot learns to do this properly. > >>>>> > >>>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com> > >>>>> --- > >>>>> > >>>>> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ > >>>>> 1 file changed, 574 insertions(+) > >>>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > >>>>> > >>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > >>>>> b/arch/arm64/ > >>>> > >>>> boot/dts/allwinner/sun50i-h616.dtsi > >>>> > >>>>> new file mode 100644 > >>>>> index 000000000000..cc06cdd15ba5 > >>>>> --- /dev/null > >>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > >>>>> @@ -0,0 +1,574 @@ > >>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > >>>>> +// Copyright (C) 2020 Arm Ltd. > >>>>> +// based on the H6 dtsi, which is: > >>>>> +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > >>>>> + > >>>>> +#include <dt-bindings/interrupt-controller/arm-gic.h> > >>>>> +#include <dt-bindings/clock/sun50i-h616-ccu.h> > >>>>> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > >>>>> +#include <dt-bindings/reset/sun50i-h616-ccu.h> > >>>>> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > >>>>> + > >>>>> +/ { > >>>>> + interrupt-parent = <&gic>; > >>>>> + #address-cells = <2>; > >>>>> + #size-cells = <2>; > >>>>> + > >>>>> + cpus { > >>>>> + #address-cells = <1>; > >>>>> + #size-cells = <0>; > >>>>> + > >>>>> + cpu0: cpu@0 { > >>>>> + compatible = "arm,cortex-a53"; > >>>>> + device_type = "cpu"; > >>>>> + reg = <0>; > >>>>> + enable-method = "psci"; > >>>>> + clocks = <&ccu CLK_CPUX>; > >>>>> + }; > >>>>> + > >>>>> + cpu1: cpu@1 { > >>>>> + compatible = "arm,cortex-a53"; > >>>>> + device_type = "cpu"; > >>>>> + reg = <1>; > >>>>> + enable-method = "psci"; > >>>>> + clocks = <&ccu CLK_CPUX>; > >>>>> + }; > >>>>> + > >>>>> + cpu2: cpu@2 { > >>>>> + compatible = "arm,cortex-a53"; > >>>>> + device_type = "cpu"; > >>>>> + reg = <2>; > >>>>> + enable-method = "psci"; > >>>>> + clocks = <&ccu CLK_CPUX>; > >>>>> + }; > >>>>> + > >>>>> + cpu3: cpu@3 { > >>>>> + compatible = "arm,cortex-a53"; > >>>>> + device_type = "cpu"; > >>>>> + reg = <3>; > >>>>> + enable-method = "psci"; > >>>>> + clocks = <&ccu CLK_CPUX>; > >>>>> + }; > >>>>> + }; > >>>>> + > >>>>> + reserved-memory { > >>>>> + #address-cells = <2>; > >>>>> + #size-cells = <2>; > >>>>> + ranges; > >>>>> + > >>>>> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > >>>>> + secmon_reserved: secmon@40000000 { > >>>>> + reg = <0x0 0x40000000 0x0 0x80000>; > >>>>> + no-map; > >>>>> + }; > >>>>> + }; > >>>> > >>>> I'm not a fan of above. If anything changes in future in BL31, U-Boot > >>>> would > >>>> need to reconfigure it anyway. Can we just skip it? > >>> > >>> I am not a fan neither, but last time I checked this is needed to boot. > >>> Indeed TF-A inserts this node, with the right values, into U-Boot's DT. > >>> And that's nicely preserved if you use that DT ($fdtcontroladdr) for > >>> the kernel as well. > >>> But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > >>> U-Boot fails to propagate the /reserved-memory node into that copy. > >>> There does not seem to be a global notion of reserved memory in U-Boot. > >>> Some commands (like tftp) explicitly parse the control DT to find and > >>> respect reserved memory regions. bootm does that also, but only to > >>> avoid placing the ramdisk or DTB into reserved memory. The information > >>> ends up in images->lmb, but is not used to generate or amend nodes in > >>> the target DT. > >>> So the bits and pieces are there, but it will require some code to be > >>> added to the generic U-Boot code. > >>> > >>> So what do you think? Leaving this out will prevent loading DTBs into > >>> U-Boot, at the moment, which sounds bad. I suggest we keep it in, for > >>> now, it should not really hurt. U-Boot will hopefully start to do the > >>> right thing soon, then we can either phase it out here (maybe when we > >>> actually change something in TF-A), or let U-Boot fix it. > >> > >> TBH, if "soon" is really soon, I would rather wait with H616 DT until U-Boot > >> supports carrying over reserved memory nodes. > > > > But this also carries compatibility issues. U-Boot support the H616 for > > more than a year now, and the earliest possible U-Boot release having that > > propagation code would be the one released in October. And then people > > would still need to update first, so that's quite some months out. > > And I was actually hoping to get at least the H616 DT patches off my > > plate, and get them into the tree to have a stable and agreed upon base > > (before this series turns into a teenager ;-) > > Then we could for instance update the U-Boot H616 support. > > There is no compatibility issue here if people are using $fdtcontroladdr. > > >> Whatever we do now, it will have > >> compatibility issues. If we introduce reserved memory node now, we can't > >> easily drop it later. Bootloaders are not very often updated, but kernels and > >> DTB files are, at least in my experience. So when we decide to drop the node? > > > > I think of the three possibilities: > > - Drop the node now, and ask people to not load DTBs explicitly > > This is my preferred solution. My position has always been that the devicetree > is provided by platform firmware, not the OS. The only reason for even > submitting the devicetree to Linux is because that is the location of the > bindings and validation tooling. Well, you are barking at the wrong tree here ;-) I am 100% behind the $fdtcontroladdr and "firmware ships DT" idea. However this relies on one thing: that there will never be an incompatible change to the DT. So at any point in time there must be exactly one best DT for that board, and that DT must be able to boot every kernel: older ones, current ones, FreeBSD ones, you name it. Because otherwise you cannot update your DT, or you lose the ability to boot a stable distro, or the stable fallback kernel that your distro installed, for instance. And this is not theoretical: Debian 11 ships with v5.10, which does not boot with a DT from >= v5.13 (r_intc binding change for most AW SoCs). And yes, this means we have to live with decisions we once made, and have to make compromises, so cannot get the DT "exactly right by the book", since we need to maintain compatibility. I strongly believe there are solutions that allow this, even if we spot mistakes later or need to amend something to make a new feature work. At the cost of being potentially somewhat "hacky". Some years ago I have been explicitly told that mainline sunxi Linux does not have the resources to pull this off, and we don't guarantee forward compatibility, which in my view renders this $fdtcontroladdr approach moot. And the r_intc binding change, also the upcoming A23 clock change tell me that this is still the position among the maintainers? Or has this position changed for new SoCs? So do we promise to never break compatibility for D1 and H616, and other new SoCs? Or even for older SoCs, from now on? > I have been using this approach for D1, and so far there have been no unsolvable > problems. Yes, most image builders assume you want to load a DTB from disk, but > teaching them not to do that is fairly simple. And yes, it means we have to do > better about keeping the U-Boot DTSs in sync, but I think we can manage that. Yes, I am very happy to update them much more regularly, and even have some prototype tool to update the DTB directly in the FIT image on SPI flash/eMMC boot/SD card/etc. Or I guess we rather explore the EFI capsule update path more. However this is all rather pointless (and actually counterproductive) if that new DT does not boot all kernels. > > - Drop the node when U-Boot learned to propagate the reservation > > - Keep the node > > the last one is the least painful: having this node in does not really > > hurt, so we can be very relaxed with this removal decision: > > Supporting explicitly-loaded DTBs is the most painful option going forward, > because that means U-Boot has to know about and propagate _every_ runtime change > made by any firmware component (not just changes made by it) to the control FDT. Yes, you have some point there. > For example, consider TF-A patching in information about idle states, or SID > contents in secure mode, or marking nodes as "reserved" because it delegates > those devices to a secure enclave. This problem is solved if we say "we support > $fdtcontroladdr, and we support overlays; but you are on your own if you load a > DTB from disk." > > Distros will continue loading DTBs from disk as long as it sorta-kinda-mostly > works, and then years later users will complain that their phone uses 4 watts at > idle, because their explicitly-loaded DTB contained idle states that their > firmware did not support (this is a true story). > > "Don't load DTBs" is a much easier story to tell if doing so is obviously broken > out of the box from day 1. I mostly agree, from a developer's point of view. My suggestion was just trying to embrace the (current) reality, and giving the user the ability to load a new DTB. But yes, they should not do this. And I actually believe distros don't really like this approach either, it's just how mainline Linux worked for most platforms: you better run with the latest DTB, and the one matching the kernel (whatever that means). So I think they will be quite happy to use U-Boot's DTB, though this needs to be the universal one. So I think the whole discussion boils down to the question of how we are going to deal with upcoming DT fixes? Do we allow them only in a compatible way? And this could be a simple thing, like adding a previously unknown regulator to a device: older kernels might not support that regulator, so the device now fails probing. This is a prominent problem for initial (minimal) DTs, where we only get PMIC support later. Sure, we could demand having PMIC support in from day one, but there might be other things we miss (like a clock gated by the RTC). Cheers, Andre > > Regards, > Samuel > > > - If U-Boot does not add the reserved node, we are covered. > > - If U-Boot adds the node, it will do so in a way where it deals with > > existing reservations. So either it doesn't actually change anything, or > > it extends the reservation. > > - Should the TF-A location actually move (and we have no plans or needs to > > do that), people would only get this by updating the firmware, at which > > point the U-Boot part would surely be in place already. We don't really > > support updating just BL31 in an existing binary firmware image, so you > > would get an updated U-Boot as well. > > > > I think the worst case scenario is that users end up with an unneeded 512K > > reservation. If they care, a firmware update should solve this problem. > > > > As for the time to remove that node: we could do that at the time when > > (or rather: if) we actually change the TF-A reservation. At the moment > > there are no plans to do this, and the size reservation is more than > > generous (the current debug build is actually 77 KB or so only). If there > > is no change, and the node stays in the .dtsi, it doesn't really hurt, see > > above. > > > >> After 10 years? Alternatively, reserved memory node can be just dropped and > >> anyone loading DTB file from outside would need to make sure it's patched. But > >> that's unexpected from user perspective, although patching DT files is done by > >> some distros. > > > > Yeah, let's not go there. As you know, I already dislike the idea of > > explicitly loading DTBs at all, but I understand this is what people, and > > distributions, do, so I'd rather have them covered. Hence the node to > > work with existing firmware. > > > > Does that make sense? > > > > Cheers, > > Andre > > > >
On Mon, 04 Jul 2022 20:42:47 +0200 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, > Dne ponedeljek, 04. julij 2022 ob 15:30:57 CEST je Andre Przywara napisal(a): > > On Sat, 02 Jul 2022 23:16:53 +0200 > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > Hi Jernej, > > > > > Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > > > > On Tue, 03 May 2022 21:05:11 +0200 > > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > > > Hi Jernej, > > > > > > > > many thanks for taking the time to wade through this file! > > > > > > > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara > napisal(a): > > > > > > This (relatively) new SoC is similar to the H6, but drops the > (broken) > > > > > > PCIe support and the USB 3.0 controller. It also gets the management > > > > > > controller removed, which in turn removes *some*, but not all of the > > > > > > devices formerly dedicated to the ARISC (CPUS). > > > > > > And while there is still the extra sunxi interrupt controller, the > > > > > > package lacks the corresponding NMI pin, so no interrupts for the > PMIC. > > > > > > > > > > > > The reserved memory node is actually handled by Trusted Firmware > now, > > > > > > but U-Boot fails to propagate this to a separately loaded DTB, so we > > > > > > keep it in here for now, until U-Boot learns to do this properly. > > > > > > > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > > > > --- > > > > > > > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 +++++++++++++++ > +++ > > > > > > 1 file changed, 574 insertions(+) > > > > > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > b/arch/arm64/ > > > > > > > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > new file mode 100644 > > > > > > index 000000000000..cc06cdd15ba5 > > > > > > --- /dev/null > > > > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > @@ -0,0 +1,574 @@ > > > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > > > > +// Copyright (C) 2020 Arm Ltd. > > > > > > +// based on the H6 dtsi, which is: > > > > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > > > + > > > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > > > > + > > > > > > +/ { > > > > > > + interrupt-parent = <&gic>; > > > > > > + #address-cells = <2>; > > > > > > + #size-cells = <2>; > > > > > > + > > > > > > + cpus { > > > > > > + #address-cells = <1>; > > > > > > + #size-cells = <0>; > > > > > > + > > > > > > + cpu0: cpu@0 { > > > > > > + compatible = "arm,cortex-a53"; > > > > > > + device_type = "cpu"; > > > > > > + reg = <0>; > > > > > > + enable-method = "psci"; > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > + }; > > > > > > + > > > > > > + cpu1: cpu@1 { > > > > > > + compatible = "arm,cortex-a53"; > > > > > > + device_type = "cpu"; > > > > > > + reg = <1>; > > > > > > + enable-method = "psci"; > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > + }; > > > > > > + > > > > > > + cpu2: cpu@2 { > > > > > > + compatible = "arm,cortex-a53"; > > > > > > + device_type = "cpu"; > > > > > > + reg = <2>; > > > > > > + enable-method = "psci"; > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > + }; > > > > > > + > > > > > > + cpu3: cpu@3 { > > > > > > + compatible = "arm,cortex-a53"; > > > > > > + device_type = "cpu"; > > > > > > + reg = <3>; > > > > > > + enable-method = "psci"; > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > + }; > > > > > > + }; > > > > > > + > > > > > > + reserved-memory { > > > > > > + #address-cells = <2>; > > > > > > + #size-cells = <2>; > > > > > > + ranges; > > > > > > + > > > > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > > > > > + secmon_reserved: secmon@40000000 { > > > > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > > > > + no-map; > > > > > > + }; > > > > > > + }; > > > > > > > > > > I'm not a fan of above. If anything changes in future in BL31, U-Boot > > > > > would > > > > > need to reconfigure it anyway. Can we just skip it? > > > > > > > > I am not a fan neither, but last time I checked this is needed to boot. > > > > Indeed TF-A inserts this node, with the right values, into U-Boot's DT. > > > > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > > > > the kernel as well. > > > > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > > > > U-Boot fails to propagate the /reserved-memory node into that copy. > > > > There does not seem to be a global notion of reserved memory in U-Boot. > > > > Some commands (like tftp) explicitly parse the control DT to find and > > > > respect reserved memory regions. bootm does that also, but only to > > > > avoid placing the ramdisk or DTB into reserved memory. The information > > > > ends up in images->lmb, but is not used to generate or amend nodes in > > > > the target DT. > > > > So the bits and pieces are there, but it will require some code to be > > > > added to the generic U-Boot code. > > > > > > > > So what do you think? Leaving this out will prevent loading DTBs into > > > > U-Boot, at the moment, which sounds bad. I suggest we keep it in, for > > > > now, it should not really hurt. U-Boot will hopefully start to do the > > > > right thing soon, then we can either phase it out here (maybe when we > > > > actually change something in TF-A), or let U-Boot fix it. > > > > > > TBH, if "soon" is really soon, I would rather wait with H616 DT until U- > Boot > > > supports carrying over reserved memory nodes. > > > > But this also carries compatibility issues. U-Boot support the H616 for > > more than a year now, and the earliest possible U-Boot release having that > > propagation code would be the one released in October. > > I was hoping you would say July (next U-Boot release) :). Well, 2022.07 was supposed to be released today, and even if that is delayed by a bit, that's obviously far too late ;-) > > And then people > > would still need to update first, so that's quite some months out. > > And I was actually hoping to get at least the H616 DT patches off my > > plate, and get them into the tree to have a stable and agreed upon base > > (before this series turns into a teenager ;-) > > Yeah, I would like that too. > > > Then we could for instance update the U-Boot H616 support. > > > > > Whatever we do now, it will have > > > compatibility issues. If we introduce reserved memory node now, we can't > > > easily drop it later. Bootloaders are not very often updated, but kernels > and > > > DTB files are, at least in my experience. So when we decide to drop the > node? > > > > I think of the three possibilities: > > - Drop the node now, and ask people to not load DTBs explicitly > > - Drop the node when U-Boot learned to propagate the reservation > > - Keep the node > > the last one is the least painful: having this node in does not really > > hurt, so we can be very relaxed with this removal decision: > > - If U-Boot does not add the reserved node, we are covered. > > - If U-Boot adds the node, it will do so in a way where it deals with > > existing reservations. So either it doesn't actually change anything, or > > it extends the reservation. > > - Should the TF-A location actually move (and we have no plans or needs to > > do that), people would only get this by updating the firmware, at which > > point the U-Boot part would surely be in place already. We don't really > > support updating just BL31 in an existing binary firmware image, so you > > would get an updated U-Boot as well. > > > > I think the worst case scenario is that users end up with an unneeded 512K > > reservation. If they care, a firmware update should solve this problem. > > > > As for the time to remove that node: we could do that at the time when > > (or rather: if) we actually change the TF-A reservation. At the moment > > there are no plans to do this, and the size reservation is more than > > generous (the current debug build is actually 77 KB or so only). If there > > is no change, and the node stays in the .dtsi, it doesn't really hurt, see > > above. > > I see your point, but I would like to get some input from Samuel first. > > Samuel, what do you think? > > > > > > After 10 years? Alternatively, reserved memory node can be just dropped > and > > > anyone loading DTB file from outside would need to make sure it's patched. > But > > > that's unexpected from user perspective, although patching DT files is done > by > > > some distros. > > > > Yeah, let's not go there. As you know, I already dislike the idea of > > explicitly loading DTBs at all, but I understand this is what people, and > > distributions, do, so I'd rather have them covered. Hence the node to > > work with existing firmware. > > Reusing DTB from U-Boot is only useful when you're happy with completeness of > DT and with the lack of bugs in it. Then you can save troubles with skipping > external DTB load step and life is easier. But as you know, features and thus > nodes are added in steps and sometimes some bugs are fixed, which means it's > extremely handy to have easily updatable DTB file. Yes, definitely, see my reply to Samuel. I just held back with the DT update in U-Boot because of the conflict between "we only take pure kernel tree DTs" and "there is a breaking change" (r_intc binding). If we find a way forward with the DT stability problem, I am happy to push for a much more frequent DT update, or even update just the DT in an existing firmware installation. This can be automated, since the DTB is just a member in the FIT image, which can be re-assembled with an updated DTB by some tool or script. Or we use capsule updates, of just the DTB, separately (if this is possible)? > Yes, U-Boot can be > automated, but it's tedious for distro to maintain one bootloader package per > board. Ideally, distro shouldn't care at all about that, Yes, I totally agree, distros should not ship firmware. Since leaving this to the board vendors is not realistic, I wonder if we (as "the sunxi community") should step up here, and provide binary builds (purely for convenience reasons) of board firmware? That could be updated from a running Linux, or put on an SD card, or fetched by distros to generate an installer? Wasn't there even some central storage offered lately by Linux, to hold (UEFI) firmware update files? > but many boards don't > have designated bootloader storage (SPI NOR flash in AW case), so they have to > be combined on same storage, partition even, as distro. Have you tried eMMC boot partitions? I found them equally convenient as SPI flash, and while not too many boards actually have SPI flash, quite some have eMMC (thinking about TV boxes). I recently even used "dual boot" with a BSP installation. And even the smallest eMMCs seem to have 4 MB per boot partition, so plenty of space for U-Boot (plus TF-A plus crust). > On the other hand, > when building kernel, you automatically build all relevant DTB files, which you > can then just copy to common place. No device specific handling needed. Also, > U-Boot doesn't sync DT files every release, so latest U-Boot doesn't necessarly > mean latest DT. Yes, for the compatibility reasons mentioned. I am more than happy to make this a regular exercise (say at each kernel's -rc3 or so). > Above is a bit off topic, but I hope you understand why distros opt to use > external DTB files (speaking from my own experiences). Yes, I understand where they (including LE) are coming from, to provide a pragmatic solution to the users' problems. And that's why I wanted to still give the possibility to load a DTB, even though I think this should not be the standard way. Cheers, Andre
Dne ponedeljek, 04. julij 2022 ob 23:58:02 CEST je Andre Przywara napisal(a): > On Mon, 04 Jul 2022 20:42:47 +0200 > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > Hi Jernej, > > > Dne ponedeljek, 04. julij 2022 ob 15:30:57 CEST je Andre Przywara napisal(a): > > > On Sat, 02 Jul 2022 23:16:53 +0200 > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > Hi Jernej, > > > > > > > Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara napisal(a): > > > > > On Tue, 03 May 2022 21:05:11 +0200 > > > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > > > > > Hi Jernej, > > > > > > > > > > many thanks for taking the time to wade through this file! > > > > > > > > > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara > > > > napisal(a): > > > > > > > This (relatively) new SoC is similar to the H6, but drops the > > > > (broken) > > > > > > > > > PCIe support and the USB 3.0 controller. It also gets the > > > > > > > management > > > > > > > controller removed, which in turn removes *some*, but not all of > > > > > > > the > > > > > > > devices formerly dedicated to the ARISC (CPUS). > > > > > > > And while there is still the extra sunxi interrupt controller, > > > > > > > the > > > > > > > package lacks the corresponding NMI pin, so no interrupts for > > > > > > > the > > > > PMIC. > > > > > > > > > The reserved memory node is actually handled by Trusted Firmware > > > > now, > > > > > > > > > but U-Boot fails to propagate this to a separately loaded DTB, > > > > > > > so we > > > > > > > keep it in here for now, until U-Boot learns to do this > > > > > > > properly. > > > > > > > > > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > > > > > --- > > > > > > > > > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 > > > > > > > +++++++++++++++ > > > > +++ > > > > > > > > > 1 file changed, 574 insertions(+) > > > > > > > create mode 100644 > > > > > > > arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > b/arch/arm64/ > > > > > > > > > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > > > new file mode 100644 > > > > > > > index 000000000000..cc06cdd15ba5 > > > > > > > --- /dev/null > > > > > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > @@ -0,0 +1,574 @@ > > > > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > > > > > +// Copyright (C) 2020 Arm Ltd. > > > > > > > +// based on the H6 dtsi, which is: > > > > > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > > > > + > > > > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > > > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > > > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > > > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > > > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > > > > > + > > > > > > > +/ { > > > > > > > + interrupt-parent = <&gic>; > > > > > > > + #address-cells = <2>; > > > > > > > + #size-cells = <2>; > > > > > > > + > > > > > > > + cpus { > > > > > > > + #address-cells = <1>; > > > > > > > + #size-cells = <0>; > > > > > > > + > > > > > > > + cpu0: cpu@0 { > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > + device_type = "cpu"; > > > > > > > + reg = <0>; > > > > > > > + enable-method = "psci"; > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > + }; > > > > > > > + > > > > > > > + cpu1: cpu@1 { > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > + device_type = "cpu"; > > > > > > > + reg = <1>; > > > > > > > + enable-method = "psci"; > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > + }; > > > > > > > + > > > > > > > + cpu2: cpu@2 { > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > + device_type = "cpu"; > > > > > > > + reg = <2>; > > > > > > > + enable-method = "psci"; > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > + }; > > > > > > > + > > > > > > > + cpu3: cpu@3 { > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > + device_type = "cpu"; > > > > > > > + reg = <3>; > > > > > > > + enable-method = "psci"; > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > + }; > > > > > > > + }; > > > > > > > + > > > > > > > + reserved-memory { > > > > > > > + #address-cells = <2>; > > > > > > > + #size-cells = <2>; > > > > > > > + ranges; > > > > > > > + > > > > > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ > > > > > > > + secmon_reserved: secmon@40000000 { > > > > > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > > > > > + no-map; > > > > > > > + }; > > > > > > > + }; > > > > > > > > > > > > I'm not a fan of above. If anything changes in future in BL31, > > > > > > U-Boot > > > > > > would > > > > > > need to reconfigure it anyway. Can we just skip it? > > > > > > > > > > I am not a fan neither, but last time I checked this is needed to > > > > > boot. > > > > > Indeed TF-A inserts this node, with the right values, into U-Boot's > > > > > DT. > > > > > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > > > > > the kernel as well. > > > > > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > > > > > U-Boot fails to propagate the /reserved-memory node into that copy. > > > > > There does not seem to be a global notion of reserved memory in > > > > > U-Boot. > > > > > Some commands (like tftp) explicitly parse the control DT to find > > > > > and > > > > > respect reserved memory regions. bootm does that also, but only to > > > > > avoid placing the ramdisk or DTB into reserved memory. The > > > > > information > > > > > ends up in images->lmb, but is not used to generate or amend nodes > > > > > in > > > > > the target DT. > > > > > So the bits and pieces are there, but it will require some code to > > > > > be > > > > > added to the generic U-Boot code. > > > > > > > > > > So what do you think? Leaving this out will prevent loading DTBs > > > > > into > > > > > U-Boot, at the moment, which sounds bad. I suggest we keep it in, > > > > > for > > > > > now, it should not really hurt. U-Boot will hopefully start to do > > > > > the > > > > > right thing soon, then we can either phase it out here (maybe when > > > > > we > > > > > actually change something in TF-A), or let U-Boot fix it. > > > > > > > > TBH, if "soon" is really soon, I would rather wait with H616 DT until > > > > U- > > > > Boot > > > > > > supports carrying over reserved memory nodes. > > > > > > But this also carries compatibility issues. U-Boot support the H616 for > > > more than a year now, and the earliest possible U-Boot release having > > > that > > > propagation code would be the one released in October. > > > > I was hoping you would say July (next U-Boot release) :). > > Well, 2022.07 was supposed to be released today, and even if that is > delayed by a bit, that's obviously far too late ;-) > > > > And then people > > > would still need to update first, so that's quite some months out. > > > And I was actually hoping to get at least the H616 DT patches off my > > > plate, and get them into the tree to have a stable and agreed upon base > > > (before this series turns into a teenager ;-) > > > > Yeah, I would like that too. > > > > > Then we could for instance update the U-Boot H616 support. > > > > > > > Whatever we do now, it will have > > > > compatibility issues. If we introduce reserved memory node now, we > > > > can't > > > > easily drop it later. Bootloaders are not very often updated, but > > > > kernels > > > > and > > > > > > DTB files are, at least in my experience. So when we decide to drop > > > > the > > > > node? > > > > > I think of the three possibilities: > > > - Drop the node now, and ask people to not load DTBs explicitly > > > - Drop the node when U-Boot learned to propagate the reservation > > > - Keep the node > > > the last one is the least painful: having this node in does not really > > > hurt, so we can be very relaxed with this removal decision: > > > - If U-Boot does not add the reserved node, we are covered. > > > - If U-Boot adds the node, it will do so in a way where it deals with > > > existing reservations. So either it doesn't actually change anything, or > > > it extends the reservation. > > > - Should the TF-A location actually move (and we have no plans or needs > > > to > > > do that), people would only get this by updating the firmware, at which > > > point the U-Boot part would surely be in place already. We don't really > > > support updating just BL31 in an existing binary firmware image, so you > > > would get an updated U-Boot as well. > > > > > > I think the worst case scenario is that users end up with an unneeded > > > 512K > > > reservation. If they care, a firmware update should solve this problem. > > > > > > As for the time to remove that node: we could do that at the time when > > > (or rather: if) we actually change the TF-A reservation. At the moment > > > there are no plans to do this, and the size reservation is more than > > > generous (the current debug build is actually 77 KB or so only). If > > > there > > > is no change, and the node stays in the .dtsi, it doesn't really hurt, > > > see > > > above. > > > > I see your point, but I would like to get some input from Samuel first. > > > > Samuel, what do you think? > > > > > > After 10 years? Alternatively, reserved memory node can be just > > > > dropped > > > > and > > > > > > anyone loading DTB file from outside would need to make sure it's > > > > patched. > > > > But > > > > > > that's unexpected from user perspective, although patching DT files is > > > > done > > > > by > > > > > > some distros. > > > > > > Yeah, let's not go there. As you know, I already dislike the idea of > > > explicitly loading DTBs at all, but I understand this is what people, > > > and > > > distributions, do, so I'd rather have them covered. Hence the node to > > > work with existing firmware. > > > > Reusing DTB from U-Boot is only useful when you're happy with completeness > > of DT and with the lack of bugs in it. Then you can save troubles with > > skipping external DTB load step and life is easier. But as you know, > > features and thus nodes are added in steps and sometimes some bugs are > > fixed, which means it's extremely handy to have easily updatable DTB > > file. > > Yes, definitely, see my reply to Samuel. I just held back with the DT > update in U-Boot because of the conflict between "we only take pure > kernel tree DTs" and "there is a breaking change" (r_intc binding). > > If we find a way forward with the DT stability problem, I am happy to > push for a much more frequent DT update, or even update just the DT in > an existing firmware installation. This can be automated, since the DTB > is just a member in the FIT image, which can be re-assembled with an > updated DTB by some tool or script. Or we use capsule updates, of just > the DTB, separately (if this is possible)? I would like to have forward compatibility too, but IMO it's not very realistic. Sooner or later we'll find something, like r_intc, again that won't be possible to integrate in forward compatible manner. > > > Yes, U-Boot can be > > automated, but it's tedious for distro to maintain one bootloader package > > per board. Ideally, distro shouldn't care at all about that, > > Yes, I totally agree, distros should not ship firmware. Since leaving > this to the board vendors is not realistic, I wonder if we (as "the > sunxi community") should step up here, and provide binary builds (purely > for convenience reasons) of board firmware? That could be updated from > a running Linux, or put on an SD card, or fetched by distros to > generate an installer? Wasn't there even some central storage offered > lately by Linux, to hold (UEFI) firmware update files? As someone who's working on distro which supports many SoCs from variety of vendors, I can tell you that we'll ship bootloader integrated into our image for years to come. Anyway, I also like to build U-Boot using my own options. For example, I disable HDMI driver for A64, H3 and H5, because it turns out that at least on H5, it can clash with Linux driver. Other distros prefer to show some splash screen, etc. One size fits all solution doesn't seems realistic to me. Maybe only if *everything* would be configurable and there would be a way for distro to preconfigure it. TBH, building U-Boot, Crust and TF-A is easy and ability to customize them is very handy. > > > but many boards don't > > have designated bootloader storage (SPI NOR flash in AW case), so they > > have to be combined on same storage, partition even, as distro. > > Have you tried eMMC boot partitions? I found them equally convenient as > SPI flash, and while not too many boards actually have SPI flash, > quite some have eMMC (thinking about TV boxes). I recently even > used "dual boot" with a BSP installation. > And even the smallest eMMCs seem to have 4 MB per boot partition, so > plenty of space for U-Boot (plus TF-A plus crust). No, I didn't. I don't see any benefit of using eMMC boot partition over treating eMMC as usual SD card and installing bootloader to sector 16. Anyway, that won't change situation at all. SD card image with integrated bootloader is still king. There are several reasons for that: - cheapest boards are most popular and usually have only SD card for storage (think OrangePi PC). There is nothing that you can do about it, except including bootloader on SD card image. - if you want to switch from Android to our distro, you need bootable SD card due to higher boot priority (speaking for AW SoCs) - not everyone wants to overwrite eMMC. Some prefer keeping Android, so it can be used later for whatever purpose. - some users have several distros for same board, each on it's own SD card. Needless to say, each distro adjusted bootloader to its needs. I like to offer flexibility in boot options, especially because it's currently easy, thanks to integrated customized bootloader and external loading of dtb files :) > > > On the other hand, > > when building kernel, you automatically build all relevant DTB files, > > which you can then just copy to common place. No device specific handling > > needed. Also, U-Boot doesn't sync DT files every release, so latest > > U-Boot doesn't necessarly mean latest DT. > > Yes, for the compatibility reasons mentioned. I am more than happy to > make this a regular exercise (say at each kernel's -rc3 or so). What about breaking changes? They can be important for new, useful functionality but older kernels won't know what to do. > Sadly, I don't think we're even close to avoiding shipping bootloader in distro images or even external DTB loading. > > Above is a bit off topic, but I hope you understand why distros opt to use > > external DTB files (speaking from my own experiences). > > Yes, I understand where they (including LE) are coming from, to provide > a pragmatic solution to the users' problems. And that's why I wanted to > still give the possibility to load a DTB, even though I think this > should not be the standard way. I think loading external DTB support is important and shouldn't be ditched anytime soon. If I understand correctly, that's an issue only on SoCs with TF- A, which means only 64-bit AW SoCs. Yes, 32-bit AW SoCs are still a thing and still used and no, I don't want TF-A there :). Best regards, Jernej
On Tue, 05 Jul 2022 19:32:26 +0200 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, so after seemingly having finished writing this email, I realised that this won't really help, as I think this diverts the discussion. And the problem has been around for a while, and won't probably be solved easily or quickly. I think we agree to disagree here, or we should admit that there are different approaches ("bundled firmware" vs. "UEFI"), so in the interest of not blocking the H616 series: Shall I just keep the firmware node? This would work both ways, whereas dropping the node would impede the "bundled firmware" approach? Answers and replies, as mentioned going potentially a bit off-topic, below. > Dne ponedeljek, 04. julij 2022 ob 23:58:02 CEST je Andre Przywara napisal(a): > > On Mon, 04 Jul 2022 20:42:47 +0200 > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > Hi Jernej, > > > > > Dne ponedeljek, 04. julij 2022 ob 15:30:57 CEST je Andre Przywara > napisal(a): > > > > On Sat, 02 Jul 2022 23:16:53 +0200 > > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > > > Hi Jernej, > > > > > > > > > Dne četrtek, 30. junij 2022 ob 02:04:10 CEST je Andre Przywara > napisal(a): > > > > > > On Tue, 03 May 2022 21:05:11 +0200 > > > > > > Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > > > > > > > > > > > > Hi Jernej, > > > > > > > > > > > > many thanks for taking the time to wade through this file! > > > > > > > > > > > > > Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara > > > > > > napisal(a): > > > > > > > > This (relatively) new SoC is similar to the H6, but drops the > > > > > > (broken) > > > > > > > > > > > PCIe support and the USB 3.0 controller. It also gets the > > > > > > > > management > > > > > > > > controller removed, which in turn removes *some*, but not all of > > > > > > > > the > > > > > > > > devices formerly dedicated to the ARISC (CPUS). > > > > > > > > And while there is still the extra sunxi interrupt controller, > > > > > > > > the > > > > > > > > package lacks the corresponding NMI pin, so no interrupts for > > > > > > > > the > > > > > > PMIC. > > > > > > > > > > > The reserved memory node is actually handled by Trusted Firmware > > > > > > now, > > > > > > > > > > > but U-Boot fails to propagate this to a separately loaded DTB, > > > > > > > > so we > > > > > > > > keep it in here for now, until U-Boot learns to do this > > > > > > > > properly. > > > > > > > > > > > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > > > > > > --- > > > > > > > > > > > > > > > > .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 > > > > > > > > +++++++++++++++ > > > > > > +++ > > > > > > > > > > > 1 file changed, 574 insertions(+) > > > > > > > > create mode 100644 > > > > > > > > arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > b/arch/arm64/ > > > > > > > > > > > > > > boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > > > > > > > > new file mode 100644 > > > > > > > > index 000000000000..cc06cdd15ba5 > > > > > > > > --- /dev/null > > > > > > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi > > > > > > > > @@ -0,0 +1,574 @@ > > > > > > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > > > > > > +// Copyright (C) 2020 Arm Ltd. > > > > > > > > +// based on the H6 dtsi, which is: > > > > > > > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > > > > > + > > > > > > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > > > > > > +#include <dt-bindings/clock/sun50i-h616-ccu.h> > > > > > > > > +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> > > > > > > > > +#include <dt-bindings/reset/sun50i-h616-ccu.h> > > > > > > > > +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > > > > > > > + > > > > > > > > +/ { > > > > > > > > + interrupt-parent = <&gic>; > > > > > > > > + #address-cells = <2>; > > > > > > > > + #size-cells = <2>; > > > > > > > > + > > > > > > > > + cpus { > > > > > > > > + #address-cells = <1>; > > > > > > > > + #size-cells = <0>; > > > > > > > > + > > > > > > > > + cpu0: cpu@0 { > > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > > + device_type = "cpu"; > > > > > > > > + reg = <0>; > > > > > > > > + enable-method = "psci"; > > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > > + }; > > > > > > > > + > > > > > > > > + cpu1: cpu@1 { > > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > > + device_type = "cpu"; > > > > > > > > + reg = <1>; > > > > > > > > + enable-method = "psci"; > > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > > + }; > > > > > > > > + > > > > > > > > + cpu2: cpu@2 { > > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > > + device_type = "cpu"; > > > > > > > > + reg = <2>; > > > > > > > > + enable-method = "psci"; > > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > > + }; > > > > > > > > + > > > > > > > > + cpu3: cpu@3 { > > > > > > > > + compatible = "arm,cortex-a53"; > > > > > > > > + device_type = "cpu"; > > > > > > > > + reg = <3>; > > > > > > > > + enable-method = "psci"; > > > > > > > > + clocks = <&ccu CLK_CPUX>; > > > > > > > > + }; > > > > > > > > + }; > > > > > > > > + > > > > > > > > + reserved-memory { > > > > > > > > + #address-cells = <2>; > > > > > > > > + #size-cells = <2>; > > > > > > > > + ranges; > > > > > > > > + > > > > > > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31) > */ > > > > > > > > + secmon_reserved: secmon@40000000 { > > > > > > > > + reg = <0x0 0x40000000 0x0 0x80000>; > > > > > > > > + no-map; > > > > > > > > + }; > > > > > > > > + }; > > > > > > > > > > > > > > I'm not a fan of above. If anything changes in future in BL31, > > > > > > > U-Boot > > > > > > > would > > > > > > > need to reconfigure it anyway. Can we just skip it? > > > > > > > > > > > > I am not a fan neither, but last time I checked this is needed to > > > > > > boot. > > > > > > Indeed TF-A inserts this node, with the right values, into U-Boot's > > > > > > DT. > > > > > > And that's nicely preserved if you use that DT ($fdtcontroladdr) for > > > > > > the kernel as well. > > > > > > But if someone *loads* a DTB into U-Boot (to $fdt_addr_r), then > > > > > > U-Boot fails to propagate the /reserved-memory node into that copy. > > > > > > There does not seem to be a global notion of reserved memory in > > > > > > U-Boot. > > > > > > Some commands (like tftp) explicitly parse the control DT to find > > > > > > and > > > > > > respect reserved memory regions. bootm does that also, but only to > > > > > > avoid placing the ramdisk or DTB into reserved memory. The > > > > > > information > > > > > > ends up in images->lmb, but is not used to generate or amend nodes > > > > > > in > > > > > > the target DT. > > > > > > So the bits and pieces are there, but it will require some code to > > > > > > be > > > > > > added to the generic U-Boot code. > > > > > > > > > > > > So what do you think? Leaving this out will prevent loading DTBs > > > > > > into > > > > > > U-Boot, at the moment, which sounds bad. I suggest we keep it in, > > > > > > for > > > > > > now, it should not really hurt. U-Boot will hopefully start to do > > > > > > the > > > > > > right thing soon, then we can either phase it out here (maybe when > > > > > > we > > > > > > actually change something in TF-A), or let U-Boot fix it. > > > > > > > > > > TBH, if "soon" is really soon, I would rather wait with H616 DT until > > > > > U- > > > > > > Boot > > > > > > > > supports carrying over reserved memory nodes. > > > > > > > > But this also carries compatibility issues. U-Boot support the H616 for > > > > more than a year now, and the earliest possible U-Boot release having > > > > that > > > > propagation code would be the one released in October. > > > > > > I was hoping you would say July (next U-Boot release) :). > > > > Well, 2022.07 was supposed to be released today, and even if that is > > delayed by a bit, that's obviously far too late ;-) > > > > > > And then people > > > > would still need to update first, so that's quite some months out. > > > > And I was actually hoping to get at least the H616 DT patches off my > > > > plate, and get them into the tree to have a stable and agreed upon base > > > > (before this series turns into a teenager ;-) > > > > > > Yeah, I would like that too. > > > > > > > Then we could for instance update the U-Boot H616 support. > > > > > > > > > Whatever we do now, it will have > > > > > compatibility issues. If we introduce reserved memory node now, we > > > > > can't > > > > > easily drop it later. Bootloaders are not very often updated, but > > > > > kernels > > > > > > and > > > > > > > > DTB files are, at least in my experience. So when we decide to drop > > > > > the > > > > > > node? > > > > > > > I think of the three possibilities: > > > > - Drop the node now, and ask people to not load DTBs explicitly > > > > - Drop the node when U-Boot learned to propagate the reservation > > > > - Keep the node > > > > the last one is the least painful: having this node in does not really > > > > hurt, so we can be very relaxed with this removal decision: > > > > - If U-Boot does not add the reserved node, we are covered. > > > > - If U-Boot adds the node, it will do so in a way where it deals with > > > > existing reservations. So either it doesn't actually change anything, or > > > > it extends the reservation. > > > > - Should the TF-A location actually move (and we have no plans or needs > > > > to > > > > do that), people would only get this by updating the firmware, at which > > > > point the U-Boot part would surely be in place already. We don't really > > > > support updating just BL31 in an existing binary firmware image, so you > > > > would get an updated U-Boot as well. > > > > > > > > I think the worst case scenario is that users end up with an unneeded > > > > 512K > > > > reservation. If they care, a firmware update should solve this problem. > > > > > > > > As for the time to remove that node: we could do that at the time when > > > > (or rather: if) we actually change the TF-A reservation. At the moment > > > > there are no plans to do this, and the size reservation is more than > > > > generous (the current debug build is actually 77 KB or so only). If > > > > there > > > > is no change, and the node stays in the .dtsi, it doesn't really hurt, > > > > see > > > > above. > > > > > > I see your point, but I would like to get some input from Samuel first. > > > > > > Samuel, what do you think? > > > > > > > > After 10 years? Alternatively, reserved memory node can be just > > > > > dropped > > > > > > and > > > > > > > > anyone loading DTB file from outside would need to make sure it's > > > > > patched. > > > > > > But > > > > > > > > that's unexpected from user perspective, although patching DT files is > > > > > done > > > > > > by > > > > > > > > some distros. > > > > > > > > Yeah, let's not go there. As you know, I already dislike the idea of > > > > explicitly loading DTBs at all, but I understand this is what people, > > > > and > > > > distributions, do, so I'd rather have them covered. Hence the node to > > > > work with existing firmware. > > > > > > Reusing DTB from U-Boot is only useful when you're happy with completeness > > > of DT and with the lack of bugs in it. Then you can save troubles with > > > skipping external DTB load step and life is easier. But as you know, > > > features and thus nodes are added in steps and sometimes some bugs are > > > fixed, which means it's extremely handy to have easily updatable DTB > > > file. > > > > Yes, definitely, see my reply to Samuel. I just held back with the DT > > update in U-Boot because of the conflict between "we only take pure > > kernel tree DTs" and "there is a breaking change" (r_intc binding). > > > > If we find a way forward with the DT stability problem, I am happy to > > push for a much more frequent DT update, or even update just the DT in > > an existing firmware installation. This can be automated, since the DTB > > is just a member in the FIT image, which can be re-assembled with an > > updated DTB by some tool or script. Or we use capsule updates, of just > > the DTB, separately (if this is possible)? > > I would like to have forward compatibility too, but IMO it's not very > realistic. Sooner or later we'll find something, like r_intc, again that won't > be possible to integrate in forward compatible manner. That's a shame, I think we should at least try. And with my x86 background let me tell you: there are solutions to those compatibility problems ;-) The more nasty ones might be borderline hackish, but it's a question of priorities, I guess. > > > Yes, U-Boot can be > > > automated, but it's tedious for distro to maintain one bootloader package > > > per board. Ideally, distro shouldn't care at all about that, > > > > Yes, I totally agree, distros should not ship firmware. Since leaving > > this to the board vendors is not realistic, I wonder if we (as "the > > sunxi community") should step up here, and provide binary builds (purely > > for convenience reasons) of board firmware? That could be updated from > > a running Linux, or put on an SD card, or fetched by distros to > > generate an installer? Wasn't there even some central storage offered > > lately by Linux, to hold (UEFI) firmware update files? > > As someone who's working on distro which supports many SoCs from variety of > vendors, But that is relative, isn't it? I count 23 supported Allwinner devices in LibreELEC, out of the 160 defconfigs in U-Boot or >180 sunxi .dts files in the kernel. So as most distributions, even with your ARM device focus, you chose to limit the number of supported devices, as that approach inherently doesn't scale. I see the reasons behind this, because of the special focus of LibreELEC, and probably the idea of giving a smooth user experience, but you could potentially cover much more devices by offering a generic UEFI image, as most *generic* distributions do, and as LE does for x86. But this relies on having a stable DT for the platform. I think conceptually this problem has been solved a long time ago: there is some interface between firmware and the kernel, which allows a generic kernel to configure itself accordingly. I refuse the idea that Arm based device should be any different in this respect. Historically, because many Arm based machines have a strong embedded background, that was not the case, but I think we should move on from those dark ages (in terms of support and maintainability). > I can tell you that we'll ship bootloader integrated into our image > for years to come. Anyway, I also like to build U-Boot using my own options. > For example, I disable HDMI driver for A64, H3 and H5, because it turns out > that at least on H5, it can clash with Linux driver. That is good to hear, please tell the sunxi U-Boot maintainer, so that we can fix it ;-) > Other distros prefer to > show some splash screen, etc. One size fits all solution doesn't seems > realistic to me. Maybe only if *everything* would be configurable and there > would be a way for distro to preconfigure it. > > TBH, building U-Boot, Crust and TF-A is easy and ability to customize them is > very handy. > > > but many boards don't > > > have designated bootloader storage (SPI NOR flash in AW case), so they > > > have to be combined on same storage, partition even, as distro. > > > > Have you tried eMMC boot partitions? I found them equally convenient as > > SPI flash, and while not too many boards actually have SPI flash, > > quite some have eMMC (thinking about TV boxes). I recently even > > used "dual boot" with a BSP installation. > > And even the smallest eMMCs seem to have 4 MB per boot partition, so > > plenty of space for U-Boot (plus TF-A plus crust). > > No, I didn't. I don't see any benefit of using eMMC boot partition over > treating eMMC as usual SD card and installing bootloader to sector 16. The firmware is out of the way of normal (accidental) accesses, as it lives in a separate block device, which is read-only, initially. And it doesn't clash with partition tables. This gives the kind of separation that people are used to on other computers: the firmware belongs to the device, the OS is provided by the user. We documented how to install firmware there in U-Boot's sunxi.rst. > Anyway, that won't change situation at all. SD card image with integrated > bootloader is still king. Sure, if you don't have any other storage, then SD card it is. But this still does not require marrying firmware and OS: you could start with a "just firmware SD card", then install the OS from a USB device, or from a generic image file copied to some SD partition. And then suddenly the pure firmware image becomes OS/distro agnostic. And conceptually this approach doesn't *prevent* separating firmware and kernel/distro, it just allows you to get away with it. > There are several reasons for that: > - cheapest boards are most popular and usually have only SD card for storage > (think OrangePi PC). There is nothing that you can do about it, except > including bootloader on SD card image. > - if you want to switch from Android to our distro, you need bootable SD card > due to higher boot priority (speaking for AW SoCs) > - not everyone wants to overwrite eMMC. Some prefer keeping Android, so it can > be used later for whatever purpose. > - some users have several distros for same board, each on it's own SD card. > Needless to say, each distro adjusted bootloader to its needs. All fine, but I don't see how this affects this discussion here. Yes, you can treat those machines like embedded devices, and bundle firmware and OS, but this is surely not the only way of deployment we should support. Being able to just offer one generic UEFI based image seems much more scalable to me. > I like to offer flexibility in boot options, especially because it's currently > easy, thanks to integrated customized bootloader and external loading of dtb > files :) Though I don't understand why you require external DTB loading: if you marry distro and firmware anyway, you could as well put your DTB of choice into U-Boot (in the U-Boot source tree, or replace it in the generated FIT image). That looks like a one-time effort in your build system? > > > On the other hand, > > > when building kernel, you automatically build all relevant DTB files, > > > which you can then just copy to common place. No device specific handling > > > needed. Also, U-Boot doesn't sync DT files every release, so latest > > > U-Boot doesn't necessarly mean latest DT. > > > > Yes, for the compatibility reasons mentioned. I am more than happy to > > make this a regular exercise (say at each kernel's -rc3 or so). > > What about breaking changes? They can be important for new, useful > functionality but older kernels won't know what to do. Yes, that is the core of this discussion. Doing this relies on not having them in the first place. There is no problem when this affects new features, or functionality that the old kernel didn't support anyway. But we must avoid change affecting older kernels. At least I would like to ask for us to try: in my experience with some thinking and clever code we can pull this off. Other platforms seem to be able to commit to this. As a compromise, I was wondering if we should define some time of grace period, initially, were we don't guarantee non-breaking changes only. So the first, say three, kernels could include breaking changes, but afterwards we stick to support at least this kernel, with every new DT to come. > > Sadly, I don't think we're even close to avoiding shipping bootloader in > distro images or even external DTB loading. > > > Above is a bit off topic, but I hope you understand why distros opt to use > > > external DTB files (speaking from my own experiences). > > > > Yes, I understand where they (including LE) are coming from, to provide > > a pragmatic solution to the users' problems. And that's why I wanted to > > still give the possibility to load a DTB, even though I think this > > should not be the standard way. > > I think loading external DTB support is important and shouldn't be ditched > anytime soon. If I understand correctly, that's an issue only on SoCs with TF- > A, which means only 64-bit AW SoCs. Yes, 32-bit AW SoCs are still a thing and > still used and no, I don't want TF-A there :). I think it's a conceptual issue, not TF-A related: A DT was always meant to be amended by firmware (think of the memory node, or the MAC address). U-Boot just decided to make those changes very late, just before launching the kernel, so that this newly loaded DTB is already available. But if the SPL decides to make changes, or picks a certain DT, you have this problem as well. Cheers, Andre
Hi Andre, Jernej, On 7/6/22 8:16 AM, Andre Przywara wrote: > so after seemingly having finished writing this email, I realised that > this won't really help, as I think this diverts the discussion. And the > problem has been around for a while, and won't probably be solved easily > or quickly. I think we agree to disagree here, or we should admit that > there are different approaches ("bundled firmware" vs. "UEFI"), so in the > interest of not blocking the H616 series: > > Shall I just keep the firmware node? This would work both ways, whereas > dropping the node would impede the "bundled firmware" approach? Let me try to sum up the relevant portion of my thoughts (and save the rest for elsewhere): The only reason to add the reserved-memory node is to support externally-loaded DTBs. By adding the node, we are committing to support externally-loaded DTBs on this SoC. Upgrading the kernel is not allowed to break boot. If we support externally-loaded DTBs, that rule extends to DTBs shipped with the kernel. If we remove the reserved-memory node, the combination of old U-Boot + new externally-loaded DTB will stop booting (the kernel version is irrelevant). Therefore, if we add the node, we can never remove it, full stop. I will (begrudgingly) accept that, as long as the node matches what TF-A actually generates today. That means, please: - Drop the label and update the node name - Reduce the size to 256 KiB, matching (BL31_LIMIT - BL31_BASE) Regards, Samuel
Dne četrtek, 07. julij 2022 ob 08:30:32 CEST je Samuel Holland napisal(a): > Hi Andre, Jernej, > > On 7/6/22 8:16 AM, Andre Przywara wrote: > > so after seemingly having finished writing this email, I realised that > > this won't really help, as I think this diverts the discussion. And the > > problem has been around for a while, and won't probably be solved easily > > or quickly. I think we agree to disagree here, or we should admit that > > there are different approaches ("bundled firmware" vs. "UEFI"), so in the > > interest of not blocking the H616 series: > > > > Shall I just keep the firmware node? This would work both ways, whereas > > dropping the node would impede the "bundled firmware" approach? > > Let me try to sum up the relevant portion of my thoughts (and save the rest > for elsewhere): > > The only reason to add the reserved-memory node is to support > externally-loaded DTBs. By adding the node, we are committing to support > externally-loaded DTBs on this SoC. > > Upgrading the kernel is not allowed to break boot. If we support > externally-loaded DTBs, that rule extends to DTBs shipped with the kernel. > > If we remove the reserved-memory node, the combination of old U-Boot + new > externally-loaded DTB will stop booting (the kernel version is irrelevant). > Therefore, if we add the node, we can never remove it, full stop. > > I will (begrudgingly) accept that, as long as the node matches what TF-A > actually generates today. That means, please: > - Drop the label and update the node name > - Reduce the size to 256 KiB, matching (BL31_LIMIT - BL31_BASE) In the interest of moving things forward, I agree to that. Best regards, Jernej
On Thu, 7 Jul 2022 01:30:32 -0500 Samuel Holland <samuel@sholland.org> wrote: Hi Samuel, > Hi Andre, Jernej, > > On 7/6/22 8:16 AM, Andre Przywara wrote: > > so after seemingly having finished writing this email, I realised that > > this won't really help, as I think this diverts the discussion. And the > > problem has been around for a while, and won't probably be solved easily > > or quickly. I think we agree to disagree here, or we should admit that > > there are different approaches ("bundled firmware" vs. "UEFI"), so in the > > interest of not blocking the H616 series: > > > > Shall I just keep the firmware node? This would work both ways, whereas > > dropping the node would impede the "bundled firmware" approach? > > Let me try to sum up the relevant portion of my thoughts (and save the rest for > elsewhere): > > The only reason to add the reserved-memory node is to support externally-loaded > DTBs. By adding the node, we are committing to support externally-loaded DTBs on > this SoC. > > Upgrading the kernel is not allowed to break boot. If we support > externally-loaded DTBs, that rule extends to DTBs shipped with the kernel. > > If we remove the reserved-memory node, the combination of old U-Boot + new > externally-loaded DTB will stop booting (the kernel version is irrelevant). > Therefore, if we add the node, we can never remove it, full stop. Well, this all depends on the initial commitment to support externally-loaded DTBs. I don't think we need to make this promise, I'd rather see this as a concession to people doing so *right now*, and for the sheer practicality of using this DT until we merge it into U-Boot. > I will (begrudgingly) accept that, as long as the node matches what TF-A > actually generates today. That means, please: > - Drop the label and update the node name I will drop the label. For the node name: the binding does not enforce it, but asks that "node names should reflect the purpose", so I went with "secmon", as used by other platforms. I will send a patch to TF-A to fix it there instead. If you disagree, feel free to fix this up before committing. > - Reduce the size to 256 KiB, matching (BL31_LIMIT - BL31_BASE) Verified in TF-A and changed. I also added a short comment explaining the situation. Feel free to amend this if needed. Many thanks for the discussion and for resolving this. I much appreciate your flexibility and pragmatism in this matter! Cheers, Andre
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi new file mode 100644 index 000000000000..cc06cdd15ba5 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi @@ -0,0 +1,574 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Arm Ltd. +// based on the H6 dtsi, which is: +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/sun50i-h616-ccu.h> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h> +#include <dt-bindings/reset/sun50i-h616-ccu.h> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + }; + + cpu1: cpu@1 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <1>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + }; + + cpu2: cpu@2 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <2>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + }; + + cpu3: cpu@3 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <3>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 512KiB reserved for ARM Trusted Firmware (BL31) */ + secmon_reserved: secmon@40000000 { + reg = <0x0 0x40000000 0x0 0x80000>; + no-map; + }; + }; + + osc24M: osc24M-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "osc24M"; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + arm,no-tick-in-suspend; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + soc@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x0 0x40000000>; + + syscon: syscon@3000000 { + compatible = "allwinner,sun50i-h616-system-control"; + reg = <0x03000000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sram_c: sram@28000 { + compatible = "mmio-sram"; + reg = <0x00028000 0x30000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00028000 0x30000>; + }; + }; + + ccu: clock@3001000 { + compatible = "allwinner,sun50i-h616-ccu"; + reg = <0x03001000 0x1000>; + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; + clock-names = "hosc", "losc", "iosc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + watchdog: watchdog@30090a0 { + compatible = "allwinner,sun50i-h616-wdt", + "allwinner,sun6i-a31-wdt"; + reg = <0x030090a0 0x20>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&osc24M>; + }; + + pio: pinctrl@300b000 { + compatible = "allwinner,sun50i-h616-pinctrl"; + reg = <0x0300b000 0x400>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + ext_rgmii_pins: rgmii-pins { + pins = "PI0", "PI1", "PI2", "PI3", "PI4", + "PI5", "PI7", "PI8", "PI9", "PI10", + "PI11", "PI12", "PI13", "PI14", "PI15", + "PI16"; + function = "emac0"; + drive-strength = <40>; + }; + + i2c0_pins: i2c0-pins { + pins = "PI6", "PI7"; + function = "i2c0"; + }; + + i2c3_ph_pins: i2c3-ph-pins { + pins = "PH4", "PH5"; + function = "i2c3"; + }; + + ir_rx_pin: ir-rx-pin { + pins = "PH10"; + function = "ir_rx"; + }; + + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", "PF3", + "PF4", "PF5"; + function = "mmc0"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", "PG3", + "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_pins: mmc2-pins { + pins = "PC0", "PC1", "PC5", "PC6", + "PC8", "PC9", "PC10", "PC11", + "PC13", "PC14", "PC15", "PC16"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + + spi0_pins: spi0-pins { + pins = "PC0", "PC2", "PC3", "PC4"; + function = "spi0"; + }; + + spi1_pins: spi1-pins { + pins = "PH6", "PH7", "PH8"; + function = "spi1"; + }; + + spi1_cs_pin: spi1-cs-pin { + pins = "PH5"; + function = "spi1"; + }; + + uart0_ph_pins: uart0-ph-pins { + pins = "PH0", "PH1"; + function = "uart0"; + }; + + uart1_pins: uart1-pins { + pins = "PG6", "PG7"; + function = "uart1"; + }; + + uart1_rts_cts_pins: uart1-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; + }; + }; + + gic: interrupt-controller@3021000 { + compatible = "arm,gic-400"; + reg = <0x03021000 0x1000>, + <0x03022000 0x2000>, + <0x03024000 0x2000>, + <0x03026000 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupt-controller; + #interrupt-cells = <3>; + }; + + mmc0: mmc@4020000 { + compatible = "allwinner,sun50i-h616-mmc", + "allwinner,sun50i-a100-mmc"; + reg = <0x04020000 0x1000>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + status = "disabled"; + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-3_3v; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@4021000 { + compatible = "allwinner,sun50i-h616-mmc", + "allwinner,sun50i-a100-mmc"; + reg = <0x04021000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + status = "disabled"; + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-3_3v; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@4022000 { + compatible = "allwinner,sun50i-h616-emmc", + "allwinner,sun50i-a100-emmc"; + reg = <0x04022000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + status = "disabled"; + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-3_3v; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + + uart0: serial@5000000 { + compatible = "snps,dw-apb-uart"; + reg = <0x05000000 0x400>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + status = "disabled"; + }; + + uart1: serial@5000400 { + compatible = "snps,dw-apb-uart"; + reg = <0x05000400 0x400>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + + uart2: serial@5000800 { + compatible = "snps,dw-apb-uart"; + reg = <0x05000800 0x400>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; + status = "disabled"; + }; + + uart3: serial@5000c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x05000c00 0x400>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; + status = "disabled"; + }; + + uart4: serial@5001000 { + compatible = "snps,dw-apb-uart"; + reg = <0x05001000 0x400>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; + status = "disabled"; + }; + + uart5: serial@5001400 { + compatible = "snps,dw-apb-uart"; + reg = <0x05001400 0x400>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; + status = "disabled"; + }; + + i2c0: i2c@5002000 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002000 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@5002400 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002400 0x400>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@5002800 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002800 0x400>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c@5002c00 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002c00 0x400>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c4: i2c@5003000 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05003000 0x400>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C4>; + resets = <&ccu RST_BUS_I2C4>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi0: spi@5010000 { + compatible = "allwinner,sun50i-h616-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05010000 0x1000>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; + clock-names = "ahb", "mod"; + resets = <&ccu RST_BUS_SPI0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@5011000 { + compatible = "allwinner,sun50i-h616-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05011000 0x1000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; + clock-names = "ahb", "mod"; + resets = <&ccu RST_BUS_SPI1>; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + emac0: ethernet@5020000 { + compatible = "allwinner,sun50i-h616-emac", + "allwinner,sun50i-a64-emac"; + syscon = <&syscon>; + reg = <0x05020000 0x10000>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC0>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC0>; + clock-names = "stmmaceth"; + status = "disabled"; + + mdio0: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + rtc: rtc@7000000 { + compatible = "allwinner,sun50i-h616-rtc"; + reg = <0x07000000 0x400>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>, + <&ccu CLK_PLL_SYSTEM_32K>; + clock-names = "bus", "hosc", + "pll-32k"; + clock-output-names = "osc32k", "osc32k-out", "iosc"; + #clock-cells = <1>; + }; + + r_ccu: clock@7010000 { + compatible = "allwinner,sun50i-h616-r-ccu"; + reg = <0x07010000 0x210>; + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, + <&ccu CLK_PLL_PERIPH0>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + r_pio: pinctrl@7022000 { + compatible = "allwinner,sun50i-h616-r-pinctrl"; + reg = <0x07022000 0x400>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + r_i2c_pins: r-i2c-pins { + pins = "PL0", "PL1"; + function = "s_i2c"; + }; + + r_rsb_pins: r-rsb-pins { + pins = "PL0", "PL1"; + function = "s_rsb"; + }; + }; + + ir: ir@7040000 { + compatible = "allwinner,sun50i-h616-ir", + "allwinner,sun6i-a31-ir"; + reg = <0x07040000 0x400>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB1_IR>, + <&r_ccu CLK_IR>; + clock-names = "apb", "ir"; + resets = <&r_ccu RST_R_APB1_IR>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_rx_pin>; + status = "disabled"; + }; + + r_i2c: i2c@7081400 { + compatible = "allwinner,sun50i-h616-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x07081400 0x400>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB2_I2C>; + resets = <&r_ccu RST_R_APB2_I2C>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + r_rsb: rsb@7083000 { + compatible = "allwinner,sun50i-h616-rsb", + "allwinner,sun8i-a23-rsb"; + reg = <0x07083000 0x400>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB2_RSB>; + clock-frequency = <3000000>; + resets = <&r_ccu RST_R_APB2_RSB>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +};
This (relatively) new SoC is similar to the H6, but drops the (broken) PCIe support and the USB 3.0 controller. It also gets the management controller removed, which in turn removes *some*, but not all of the devices formerly dedicated to the ARISC (CPUS). And while there is still the extra sunxi interrupt controller, the package lacks the corresponding NMI pin, so no interrupts for the PMIC. The reserved memory node is actually handled by Trusted Firmware now, but U-Boot fails to propagate this to a separately loaded DTB, so we keep it in here for now, until U-Boot learns to do this properly. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++ 1 file changed, 574 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi