diff mbox series

[v1,3/3] riscv: dts: starfive: add PCIe dts configuration for JH7110

Message ID 20230406111142.74410-4-minda.chen@starfivetech.com (mailing list archive)
State New, archived
Delegated to: Krzysztof Wilczyński
Headers show
Series Add JH7110 PCIe driver support | expand

Commit Message

Minda Chen April 6, 2023, 11:11 a.m. UTC 
The PCIe is a PCIe2, single lane PCIe compliant controller.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 .../jh7110-starfive-visionfive-2.dtsi         | 58 ++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      | 88 +++++++++++++++++++
 2 files changed, 146 insertions(+)

Comments

Krzysztof Kozlowski April 6, 2023, 6:25 p.m. UTC | #1 
On 06/04/2023 13:11, Minda Chen wrote:
> The PCIe is a PCIe2, single lane PCIe compliant controller.
> 
> Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 58 ++++++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 88 +++++++++++++++++++
>  2 files changed, 146 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index cf0a66faf5d3..4552919e69b0 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -191,6 +191,50 @@
>  		};
>  	};
>  
> +	pcie0_wake_default: pcie0_wake_default {

No underscores in node names. Test your patches against bindings before
sending.


>  	uart0_pins: uart0-0 {
>  		tx-pins {
>  			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
> @@ -228,3 +272,17 @@
>  	dr_mode = "peripheral";
>  	status = "okay";
>  };
> +
> +&pcie0 {
> +	pinctrl-names = "default";
> +	reset-gpios = <&sysgpio 26 GPIO_ACTIVE_LOW>;
> +	phys = <&pciephy0>;
> +	status = "okay";
> +};
> +
> +&pcie1 {
> +	pinctrl-names = "default";
> +	reset-gpios = <&sysgpio 28 GPIO_ACTIVE_LOW>;
> +	phys = <&pciephy1>;
> +	status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 2f67196ffac0..c309ec550ba7 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -642,5 +642,93 @@
>  			#reset-cells = <1>;
>  			power-domains = <&pwrc JH7110_PD_VOUT>;
>  		};
> +
> +		pcie0: pcie@2B000000 {

Lower case hex.

> +			compatible = "starfive,jh7110-pcie";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			#interrupt-cells = <1>;

Why reg is not second property?

> +			reg = <0x0 0x2B000000 0x0 0x1000000
> +			       0x9 0x40000000 0x0 0x10000000>;
> +			reg-names = "reg", "config";
> +			device_type = "pci";
> +			starfive,stg-syscon = <&stg_syscon 0xc0 0xc4 0x130 0x1b8>;
> +			bus-range = <0x0 0xff>;
> +			ranges = <0x82000000  0x0 0x30000000  0x0 0x30000000 0x0 0x08000000>,
> +				 <0xc3000000  0x9 0x00000000  0x9 0x00000000 0x0 0x40000000>;
> +			interrupts = <56>;

Your binding requires cells, so I am pretty sure you did not test what
you wrote.



Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index cf0a66faf5d3..4552919e69b0 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -191,6 +191,50 @@ 
 		};
 	};
 
+	pcie0_wake_default: pcie0_wake_default {
+		wake-pins {
+			pinmux = <GPIOMUX(32, GPOUT_HIGH, GPOEN_ENABLE, GPI_NONE)>;
+			bias-disable;
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	pcie0_clkreq_default: pcie0_clkreq_default {
+		clkreq-pins {
+			bias-disable;
+			pinmux = <GPIOMUX(27, GPOUT_HIGH, GPOEN_ENABLE, GPI_NONE)>;
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	pcie1_wake_default: pcie1_wake_default {
+		wake-pins {
+			bias-disable;
+			pinmux = <GPIOMUX(21, GPOUT_HIGH, GPOEN_ENABLE, GPI_NONE)>;
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	pcie1_clkreq_default: pcie1_clkreq_default {
+		clkreq-pins {
+			bias-disable;
+			pinmux = <GPIOMUX(29, GPOUT_HIGH, GPOEN_ENABLE, GPI_NONE)>;
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
 	uart0_pins: uart0-0 {
 		tx-pins {
 			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
@@ -228,3 +272,17 @@ 
 	dr_mode = "peripheral";
 	status = "okay";
 };
+
+&pcie0 {
+	pinctrl-names = "default";
+	reset-gpios = <&sysgpio 26 GPIO_ACTIVE_LOW>;
+	phys = <&pciephy0>;
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	reset-gpios = <&sysgpio 28 GPIO_ACTIVE_LOW>;
+	phys = <&pciephy1>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 2f67196ffac0..c309ec550ba7 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -642,5 +642,93 @@ 
 			#reset-cells = <1>;
 			power-domains = <&pwrc JH7110_PD_VOUT>;
 		};
+
+		pcie0: pcie@2B000000 {
+			compatible = "starfive,jh7110-pcie";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			reg = <0x0 0x2B000000 0x0 0x1000000
+			       0x9 0x40000000 0x0 0x10000000>;
+			reg-names = "reg", "config";
+			device_type = "pci";
+			starfive,stg-syscon = <&stg_syscon 0xc0 0xc4 0x130 0x1b8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000  0x0 0x30000000  0x0 0x30000000 0x0 0x08000000>,
+				 <0xc3000000  0x9 0x00000000  0x9 0x00000000 0x0 0x40000000>;
+			interrupts = <56>;
+			interrupt-parent = <&plic>;
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc0 0x1>,
+					<0x0 0x0 0x0 0x2 &pcie_intc0 0x2>,
+					<0x0 0x0 0x0 0x3 &pcie_intc0 0x3>,
+					<0x0 0x0 0x0 0x4 &pcie_intc0 0x4>;
+			msi-parent = <&pcie0>;
+			msi-controller;
+			clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
+				 <&stgcrg JH7110_STGCLK_PCIE0_TL>,
+				 <&stgcrg JH7110_STGCLK_PCIE0_AXI_MST0>,
+				 <&stgcrg JH7110_STGCLK_PCIE0_APB>;
+			clock-names = "noc", "tl", "axi_mst0", "apb";
+			resets = <&stgcrg JH7110_STGRST_PCIE0_AXI_MST0>,
+				 <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV0>,
+				 <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV>,
+				 <&stgcrg JH7110_STGRST_PCIE0_BRG>,
+				 <&stgcrg JH7110_STGRST_PCIE0_CORE>,
+				 <&stgcrg JH7110_STGRST_PCIE0_APB>;
+			reset-names = "mst0", "slv0", "slv", "brg",
+				      "core", "apb";
+			status = "disabled";
+
+			pcie_intc0: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie1: pcie@2C000000 {
+			compatible = "starfive,jh7110-pcie";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			reg = <0x0 0x2C000000 0x0 0x1000000
+			       0x9 0xc0000000 0x0 0x10000000>;
+			reg-names = "reg", "config";
+			device_type = "pci";
+			starfive,stg-syscon = <&stg_syscon 0x270 0x274 0x2e0 0x368>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000  0x0 0x38000000  0x0 0x38000000 0x0 0x08000000>,
+				 <0xc3000000  0x9 0x80000000  0x9 0x80000000 0x0 0x40000000>;
+			interrupts = <57>;
+			interrupt-parent = <&plic>;
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc1 0x1>,
+					<0x0 0x0 0x0 0x2 &pcie_intc1 0x2>,
+					<0x0 0x0 0x0 0x3 &pcie_intc1 0x3>,
+					<0x0 0x0 0x0 0x4 &pcie_intc1 0x4>;
+			msi-parent = <&pcie1>;
+			msi-controller;
+			clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
+				 <&stgcrg JH7110_STGCLK_PCIE1_TL>,
+				 <&stgcrg JH7110_STGCLK_PCIE1_AXI_MST0>,
+				 <&stgcrg JH7110_STGCLK_PCIE1_APB>;
+			clock-names = "noc", "tl", "axi_mst0", "apb";
+			resets = <&stgcrg JH7110_STGRST_PCIE1_AXI_MST0>,
+				 <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV0>,
+				 <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV>,
+				 <&stgcrg JH7110_STGRST_PCIE1_BRG>,
+				 <&stgcrg JH7110_STGRST_PCIE1_CORE>,
+				 <&stgcrg JH7110_STGRST_PCIE1_APB>;
+			reset-names = "mst0", "slv0", "slv", "brg",
+				      "core", "apb";
+			status = "disabled";
+
+			pcie_intc1: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
 	};
 };