@@ -342,6 +342,15 @@ config PCIE_XILINX_CPM
Say 'Y' here if you want kernel support for the
Xilinx Versal CPM host bridge.
+config PCI_SH7751
+ bool "Renesas SH7751 PCI controller"
+ depends on OF
+ depends on CPU_SUBTYPE_SH7751 || CPU_SUBTYPE_SH7751R || COMPILE_TEST
+ select PCI_HOST_COMMON
+ help
+ Say 'Y' here if you want kernel to support the Renesas SH7751 PCI
+ Host Bridge driver.
+
source "drivers/pci/controller/cadence/Kconfig"
source "drivers/pci/controller/dwc/Kconfig"
source "drivers/pci/controller/mobiveil/Kconfig"
@@ -39,6 +39,7 @@ obj-$(CONFIG_PCI_LOONGSON) += pci-loongson.o
obj-$(CONFIG_PCIE_HISI_ERR) += pcie-hisi-error.o
obj-$(CONFIG_PCIE_APPLE) += pcie-apple.o
obj-$(CONFIG_PCIE_MT7621) += pcie-mt7621.o
+obj-$(CONFIG_PCI_SH7751) += pci-sh7751.o
# pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
obj-y += dwc/
new file mode 100644
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SH7751 PCI driver
+ * Copyright (C) 2023 Yoshinori Sato
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci-ecam.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <asm-generic/pci.h>
+#include <asm/addrspace.h>
+#include "pci-sh7751.h"
+
+#define pcic_writel(val, base, reg) __raw_writel(val, base + (reg))
+#define pcic_readl(base, reg) __raw_readl(base + (reg))
+
+/*
+ * PCIC fixups
+ */
+
+static inline void pci_fixup_write_regs(struct device_node *np,
+ const char *prop,
+ void __iomem *pcic, int reg,
+ int nr_regs)
+{
+ int i;
+ u32 val;
+
+ for (i = 0; i < nr_regs; i++) {
+ if (of_property_read_u32_index(np, prop, i, &val))
+ pcic_writel(val, pcic, reg + i * 4);
+ }
+}
+
+#define SH7751_NUM_CONFIG 18
+static void pcic_fixups(struct device_node *np,
+ void __iomem *pcic, void __iomem *bcr)
+{
+ unsigned long bcr1, mcr;
+ u32 val;
+ int i, r;
+ u32 pci_config[SH7751_NUM_CONFIG * 2];
+
+ const struct {
+ const char *name;
+ int reg;
+ int nr;
+ } reg_prop[] = {
+ /*
+ * The bus timing uses the bootloader settings,
+ * so do not change them here.
+ */
+ { "renesas,intm", SH4_PCIINTM, 1, },
+ { "renesas,aintm", SH4_PCIAINTM, 1, },
+ { "renesas,lsr", SH4_PCILSR0, 2, },
+ { "renesas,lar", SH4_PCILAR0, 2, },
+ { "renesas,dmabt", SH4_PCIDMABT, 1, },
+ { "renesas,pintm", SH4_PCIPINTM, 1, },
+ };
+
+ if (of_property_read_u32(np, "sh7751-pci,bcr1", &val)) {
+ bcr1 = ioread32(bcr + SH7751_BCR1);
+ bcr1 |= val;
+ pcic_writel(bcr1, pcic, SH4_PCIBCR1);
+ }
+ if (of_property_read_u32(np, "renesas,clkr", &val)) {
+ val |= 0xa5 << 24;
+ pcic_writel(val, pcic, SH4_PCIBCR1);
+ }
+ for (i = 0; i < ARRAY_SIZE(reg_prop); i++)
+ pci_fixup_write_regs(np, reg_prop[i].name, pcic,
+ reg_prop[i].reg, reg_prop[i].nr);
+
+ memset(pci_config, 0, sizeof(pci_config));
+ if (of_property_read_u32_array(np, "renesas,config",
+ pci_config, SH7751_NUM_CONFIG) == 0) {
+ for (i = 0; i < SH7751_NUM_CONFIG; i++) {
+ r = pci_config[i * 2];
+ /* CONFIG0 is read-only, so make it a sentinel. */
+ if (r == 0)
+ break;
+ pcic_writel(pci_config[i * 2 + 1], pcic,
+ SH7751_PCICONF0 + r * 4);
+ }
+ }
+
+ if (of_property_read_u32(np, "sh7751-pci,mcrmask", &val)) {
+ mcr = ioread32(bcr + SH7751_MCR);
+ mcr &= ~val;
+ pcic_writel(mcr, pcic, SH4_PCIMCR);
+ }
+}
+
+/*
+ * Direct access to PCI hardware...
+ */
+#define CONFIG_CMD(bus, devfn, where) \
+ (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
+
+/*
+ * We need to avoid collisions with `mirrored' VGA ports
+ * and other strange ISA hardware, so we always want the
+ * addresses to be allocated in the 0x000-0x0ff region
+ * modulo 0x400.
+ */
+#define IO_REGION_BASE 0x1000
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+ resource_size_t size, resource_size_t align)
+{
+ resource_size_t start = res->start;
+
+ if (res->flags & IORESOURCE_IO) {
+ if (start < PCIBIOS_MIN_IO + IO_REGION_BASE)
+ start = PCIBIOS_MIN_IO + IO_REGION_BASE;
+
+ /*
+ * Put everything into 0x00-0xff region modulo 0x400.
+ */
+ if (start & 0x300)
+ start = (start + 0x3ff) & ~0x3ff;
+ }
+
+ return start;
+}
+
+static int area_sdram_check(struct device *dev, void __iomem *pcic,
+ void __iomem *bcr, unsigned int area)
+{
+ unsigned long word;
+
+ word = __raw_readl(bcr + SH7751_BCR1);
+ /* check BCR for SDRAM in area */
+ if (((word >> area) & 1) == 0) {
+ dev_info(dev, "PCI: Area %d is not configured for SDRAM. BCR1=0x%lx\n",
+ area, word);
+ return 0;
+ }
+ pcic_writel(word, pcic, SH4_PCIBCR1);
+
+ word = __raw_readw(bcr + SH7751_BCR2);
+ /* check BCR2 for 32bit SDRAM interface*/
+ if (((word >> (area << 1)) & 0x3) != 0x3) {
+ dev_info(dev, "PCI: Area %d is not 32 bit SDRAM. BCR2=0x%lx\n",
+ area, word);
+ return 0;
+ }
+ pcic_writel(word, pcic, SH4_PCIBCR2);
+
+ return 1;
+}
+
+static void set_pci_window(void __iomem *pcic, int no, struct resource *res)
+{
+ u32 word;
+
+ word = res->end - res->start - 1;
+ pcic_writel(word, pcic, SH4_PCILSR0 + no * 4);
+ word = P2SEGADDR(res->start);
+ pcic_writel(word, pcic, SH4_PCILAR0 + no * 4);
+ pcic_writel(word, pcic, SH7751_PCICONF5 + no * 4);
+}
+
+static int sh7751_pci_probe(struct platform_device *pdev)
+{
+ struct resource *res, *w0res;
+ u32 id;
+ u32 reg, word;
+ void __iomem *pcic;
+ void __iomem *bcr;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pcic = (void __iomem *)res->start;
+ if (IS_ERR(pcic))
+ return PTR_ERR(pcic);
+
+ w0res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (IS_ERR(w0res))
+ return PTR_ERR(w0res);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ bcr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(bcr))
+ return PTR_ERR(bcr);
+
+ /* check for SH7751/SH7751R hardware */
+ id = pcic_readl(pcic, SH7751_PCICONF0);
+ if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) &&
+ id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) {
+ dev_warn(&pdev->dev, "PCI: This is not an SH7751(R)\n");
+ return -ENODEV;
+ }
+ dev_info(&pdev->dev, "PCI core found at %pR\n", pcic);
+
+ /* Set the BCR's to enable PCI access */
+ reg = __raw_readl(bcr);
+ reg |= 0x80000;
+ __raw_writel(reg, bcr);
+
+ /* Turn the clocks back on (not done in reset)*/
+ pcic_writel(0, pcic, SH4_PCICLKR);
+ /* Clear Powerdown IRQ's (not done in reset) */
+ word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0;
+ pcic_writel(word, pcic, SH4_PCIPINT);
+
+ /* set the command/status bits to:
+ * Wait Cycle Control + Parity Enable + Bus Master +
+ * Mem space enable
+ */
+ word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER |
+ SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES;
+ pcic_writel(word, pcic, SH7751_PCICONF1);
+
+ /* define this host as the host bridge */
+ word = PCI_BASE_CLASS_BRIDGE << 24;
+ pcic_writel(word, pcic, SH7751_PCICONF2);
+
+ /* Set IO and Mem windows to local address
+ * Make PCI and local address the same for easy 1 to 1 mapping
+ */
+ set_pci_window(pcic, 0, w0res); /* memory */
+
+ /* check BCR for SDRAM in specified area */
+ area_sdram_check(&pdev->dev, pcic, bcr, (w0res->start >> 27) & 0x07);
+
+ /* configure the wait control registers */
+ word = __raw_readl(bcr + SH7751_WCR1);
+ pcic_writel(word, pcic, SH4_PCIWCR1);
+ word = __raw_readl(bcr + SH7751_WCR2);
+ pcic_writel(word, pcic, SH4_PCIWCR2);
+ word = __raw_readl(bcr + SH7751_WCR3);
+ pcic_writel(word, pcic, SH4_PCIWCR3);
+ word = __raw_readl(bcr + SH7751_MCR);
+ pcic_writel(word, pcic, SH4_PCIMCR);
+
+ /* Override register setting */
+ pcic_fixups(pdev->dev.of_node, pcic, bcr);
+
+ /* SH7751 init done, set central function init complete */
+ /* use round robin mode to stop a device starving/overrunning */
+ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM;
+ pcic_writel(word, pcic, SH4_PCICR);
+
+ return pci_host_common_probe(pdev);
+}
+
+static void __iomem *sh4_pci_map_bus(struct pci_bus *bus,
+ unsigned int devfn, int where)
+{
+ struct pci_config_window *cfg = bus->sysdata;
+ void __iomem *pcic = (void __iomem *)cfg->res.start;
+
+ pcic_writel(CONFIG_CMD(bus, devfn, where), pcic, SH4_PCIPAR);
+ return pcic + SH4_PCIPDR;
+}
+
+static const struct pci_ecam_ops pci_sh7751_bus_ops = {
+ .pci_ops = {
+ .map_bus = sh4_pci_map_bus,
+ .read = pci_generic_config_read32,
+ .write = pci_generic_config_write32,
+ }
+};
+
+static const struct of_device_id sh7751_pci_of_match[] = {
+ { .compatible = "renesas,pci-sh7751",
+ .data = &pci_sh7751_bus_ops },
+ { }
+};
+MODULE_DEVICE_TABLE(of, sh7751_pci_of_match);
+
+static struct platform_driver sh7751_pci_driver = {
+ .driver = {
+ .name = "pci-sh7751",
+ .of_match_table = sh7751_pci_of_match,
+ },
+ .probe = sh7751_pci_probe,
+};
+module_platform_driver(sh7751_pci_driver);
+
+MODULE_DESCRIPTION("SH7751 PCI driver");
new file mode 100644
@@ -0,0 +1,267 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Low-Level PCI Support for SH7751 targets
+ *
+ * Dustin McIntire (dustin@sensoria.com) (c) 2001
+ * Paul Mundt (lethal@linux-sh.org) (c) 2003
+ *
+ */
+
+#ifndef _PCI_SH7751_H_
+#define _PCI_SH7751_H_
+
+#define SH4_PCICR 0x100 /* PCI Control Register */
+ #define SH4_PCICR_PREFIX 0xA5000000 /* CR prefix for write */
+ #define SH4_PCICR_FTO 0x00000400 /* TRDY/IRDY Enable */
+ #define SH4_PCICR_TRSB 0x00000200 /* Target Read Single */
+ #define SH4_PCICR_BSWP 0x00000100 /* Target Byte Swap */
+ #define SH4_PCICR_PLUP 0x00000080 /* Enable PCI Pullup */
+ #define SH4_PCICR_ARBM 0x00000040 /* PCI Arbitration Mode */
+ #define SH4_PCICR_MD 0x00000030 /* MD9 and MD10 status */
+ #define SH4_PCICR_SERR 0x00000008 /* SERR output assert */
+ #define SH4_PCICR_INTA 0x00000004 /* INTA output assert */
+ #define SH4_PCICR_PRST 0x00000002 /* PCI Reset Assert */
+ #define SH4_PCICR_CFIN 0x00000001 /* Central Fun. Init Done */
+#define SH4_PCILSR0 0x104 /* PCI Local Space Register0 */
+#define SH4_PCILSR1 0x108 /* PCI Local Space Register1 */
+#define SH4_PCILAR0 0x10C /* PCI Local Addr Register1 */
+#define SH4_PCILAR1 0x110 /* PCI Local Addr Register1 */
+#define SH4_PCIINT 0x114 /* PCI Interrupt Register */
+ #define SH4_PCIINT_MLCK 0x00008000 /* Master Lock Error */
+ #define SH4_PCIINT_TABT 0x00004000 /* Target Abort Error */
+ #define SH4_PCIINT_TRET 0x00000200 /* Target Retry Error */
+ #define SH4_PCIINT_MFDE 0x00000100 /* Master Func. Disable Error */
+ #define SH4_PCIINT_PRTY 0x00000080 /* Address Parity Error */
+ #define SH4_PCIINT_SERR 0x00000040 /* SERR Detection Error */
+ #define SH4_PCIINT_TWDP 0x00000020 /* Tgt. Write Parity Error */
+ #define SH4_PCIINT_TRDP 0x00000010 /* Tgt. Read Parity Err Det. */
+ #define SH4_PCIINT_MTABT 0x00000008 /* Master-Tgt. Abort Error */
+ #define SH4_PCIINT_MMABT 0x00000004 /* Master-Master Abort Error */
+ #define SH4_PCIINT_MWPD 0x00000002 /* Master Write PERR Detect */
+ #define SH4_PCIINT_MRPD 0x00000001 /* Master Read PERR Detect */
+#define SH4_PCIINTM 0x118 /* PCI Interrupt Mask */
+ #define SH4_PCIINTM_TTADIM BIT(14) /* Target-target abort interrupt */
+ #define SH4_PCIINTM_TMTOIM BIT(9) /* Target retry timeout */
+ #define SH4_PCIINTM_MDEIM BIT(8) /* Master function disable error */
+ #define SH4_PCIINTM_APEDIM BIT(7) /* Address parity error detection */
+ #define SH4_PCIINTM_SDIM BIT(6) /* SERR detection */
+ #define SH4_PCIINTM_DPEITWM BIT(5) /* Data parity error for target write */
+ #define SH4_PCIINTM_PEDITRM BIT(4) /* PERR detection for target read */
+ #define SH4_PCIINTM_TADIMM BIT(3) /* Target abort for master */
+ #define SH4_PCIINTM_MADIMM BIT(2) /* Master abort for master */
+ #define SH4_PCIINTM_MWPDIM BIT(1) /* Master write data parity error */
+ #define SH4_PCIINTM_MRDPEIM BIT(0) /* Master read data parity error */
+#define SH4_PCIALR 0x11C /* Error Address Register */
+#define SH4_PCICLR 0x120 /* Error Command/Data */
+ #define SH4_PCICLR_MPIO 0x80000000
+ #define SH4_PCICLR_MDMA0 0x40000000 /* DMA0 Transfer Error */
+ #define SH4_PCICLR_MDMA1 0x20000000 /* DMA1 Transfer Error */
+ #define SH4_PCICLR_MDMA2 0x10000000 /* DMA2 Transfer Error */
+ #define SH4_PCICLR_MDMA3 0x08000000 /* DMA3 Transfer Error */
+ #define SH4_PCICLR_TGT 0x04000000 /* Target Transfer Error */
+ #define SH4_PCICLR_CMDL 0x0000000F /* PCI Command at Error */
+#define SH4_PCIAINT 0x130 /* Arbiter Interrupt Register */
+ #define SH4_PCIAINT_MBKN 0x00002000 /* Master Broken Interrupt */
+ #define SH4_PCIAINT_TBTO 0x00001000 /* Target Bus Time Out */
+ #define SH4_PCIAINT_MBTO 0x00000800 /* Master Bus Time Out */
+ #define SH4_PCIAINT_TABT 0x00000008 /* Target Abort */
+ #define SH4_PCIAINT_MABT 0x00000004 /* Master Abort */
+ #define SH4_PCIAINT_RDPE 0x00000002 /* Read Data Parity Error */
+ #define SH4_PCIAINT_WDPE 0x00000001 /* Write Data Parity Error */
+#define SH4_PCIAINTM 0x134 /* Arbiter Int. Mask Register */
+#define SH4_PCIBMLR 0x138 /* Error Bus Master Register */
+ #define SH4_PCIBMLR_REQ4 0x00000010 /* REQ4 bus master at error */
+ #define SH4_PCIBMLR_REQ3 0x00000008 /* REQ3 bus master at error */
+ #define SH4_PCIBMLR_REQ2 0x00000004 /* REQ2 bus master at error */
+ #define SH4_PCIBMLR_REQ1 0x00000002 /* REQ1 bus master at error */
+ #define SH4_PCIBMLR_REQ0 0x00000001 /* REQ0 bus master at error */
+#define SH4_PCIDMABT 0x140 /* DMA Transfer Arb. Register */
+ #define SH4_PCIDMABT_RRBN 0x00000001 /* DMA Arbitor Round-Robin */
+#define SH4_PCIDPA0 0x180 /* DMA0 Transfer Addr. */
+#define SH4_PCIDLA0 0x184 /* DMA0 Local Addr. */
+#define SH4_PCIDTC0 0x188 /* DMA0 Transfer Cnt. */
+#define SH4_PCIDCR0 0x18C /* DMA0 Control Register */
+ #define SH4_PCIDCR_ALGN 0x00000600 /* DMA Alignment Mode */
+ #define SH4_PCIDCR_MAST 0x00000100 /* DMA Termination Type */
+ #define SH4_PCIDCR_INTM 0x00000080 /* DMA Interrupt Done Mask*/
+ #define SH4_PCIDCR_INTS 0x00000040 /* DMA Interrupt Done Status */
+ #define SH4_PCIDCR_LHLD 0x00000020 /* Local Address Control */
+ #define SH4_PCIDCR_PHLD 0x00000010 /* PCI Address Control*/
+ #define SH4_PCIDCR_IOSEL 0x00000008 /* PCI Address Space Type */
+ #define SH4_PCIDCR_DIR 0x00000004 /* DMA Transfer Direction */
+ #define SH4_PCIDCR_STOP 0x00000002 /* Force DMA Stop */
+ #define SH4_PCIDCR_STRT 0x00000001 /* DMA Start */
+#define SH4_PCIDPA1 0x190 /* DMA1 Transfer Addr. */
+#define SH4_PCIDLA1 0x194 /* DMA1 Local Addr. */
+#define SH4_PCIDTC1 0x198 /* DMA1 Transfer Cnt. */
+#define SH4_PCIDCR1 0x19C /* DMA1 Control Register */
+#define SH4_PCIDPA2 0x1A0 /* DMA2 Transfer Addr. */
+#define SH4_PCIDLA2 0x1A4 /* DMA2 Local Addr. */
+#define SH4_PCIDTC2 0x1A8 /* DMA2 Transfer Cnt. */
+#define SH4_PCIDCR2 0x1AC /* DMA2 Control Register */
+#define SH4_PCIDPA3 0x1B0 /* DMA3 Transfer Addr. */
+#define SH4_PCIDLA3 0x1B4 /* DMA3 Local Addr. */
+#define SH4_PCIDTC3 0x1B8 /* DMA3 Transfer Cnt. */
+#define SH4_PCIDCR3 0x1BC /* DMA3 Control Register */
+#define SH4_PCIPAR 0x1C0 /* PIO Address Register */
+ #define SH4_PCIPAR_CFGEN 0x80000000 /* Configuration Enable */
+ #define SH4_PCIPAR_BUSNO 0x00FF0000 /* Config. Bus Number */
+ #define SH4_PCIPAR_DEVNO 0x0000FF00 /* Config. Device Number */
+ #define SH4_PCIPAR_REGAD 0x000000FC /* Register Address Number */
+#define SH4_PCIMBR 0x1C4 /* Memory Base Address */
+ #define SH4_PCIMBR_MASK 0xFF000000 /* Memory Space Mask */
+ #define SH4_PCIMBR_LOCK 0x00000001 /* Lock Memory Space */
+#define SH4_PCIIOBR 0x1C8 /* I/O Base Address Register */
+ #define SH4_PCIIOBR_MASK 0xFFFC0000 /* IO Space Mask */
+ #define SH4_PCIIOBR_LOCK 0x00000001 /* Lock IO Space */
+#define SH4_PCIPINT 0x1CC /* Power Mgmnt Int. Register */
+ #define SH4_PCIPINT_D3 0x00000002 /* D3 Pwr Mgmt. Interrupt */
+ #define SH4_PCIPINT_D0 0x00000001 /* D0 Pwr Mgmt. Interrupt */
+#define SH4_PCIPINTM 0x1D0 /* Power Mgmnt Mask Register */
+#define SH4_PCICLKR 0x1D4 /* Clock Ctrl. Register */
+ #define SH4_PCICLKR_PCSTP 0x00000002 /* PCI Clock Stop */
+ #define SH4_PCICLKR_BCSTP 0x00000001 /* BCLK Clock Stop */
+/* For definitions of BCR, MCR see ... */
+#define SH4_PCIBCR1 0x1E0 /* Memory BCR1 Register */
+ #define SH4_PCIMBR0 SH4_PCIBCR1
+#define SH4_PCIBCR2 0x1E4 /* Memory BCR2 Register */
+ #define SH4_PCIMBMR0 SH4_PCIBCR2
+#define SH4_PCIWCR1 0x1E8 /* Wait Control 1 Register */
+#define SH4_PCIWCR2 0x1EC /* Wait Control 2 Register */
+#define SH4_PCIWCR3 0x1F0 /* Wait Control 3 Register */
+ #define SH4_PCIMBR2 SH4_PCIWCR3
+#define SH4_PCIMCR 0x1F4 /* Memory Control Register */
+#define SH4_PCIBCR3 0x1f8 /* Memory BCR3 Register */
+#define SH4_PCIPCTR 0x200 /* Port Control Register */
+ #define SH4_PCIPCTR_P2EN 0x000400000 /* Port 2 Enable */
+ #define SH4_PCIPCTR_P1EN 0x000200000 /* Port 1 Enable */
+ #define SH4_PCIPCTR_P0EN 0x000100000 /* Port 0 Enable */
+ #define SH4_PCIPCTR_P2UP 0x000000020 /* Port2 Pull Up Enable */
+ #define SH4_PCIPCTR_P2IO 0x000000010 /* Port2 Output Enable */
+ #define SH4_PCIPCTR_P1UP 0x000000008 /* Port1 Pull Up Enable */
+ #define SH4_PCIPCTR_P1IO 0x000000004 /* Port1 Output Enable */
+ #define SH4_PCIPCTR_P0UP 0x000000002 /* Port0 Pull Up Enable */
+ #define SH4_PCIPCTR_P0IO 0x000000001 /* Port0 Output Enable */
+#define SH4_PCIPDTR 0x204 /* Port Data Register */
+ #define SH4_PCIPDTR_PB5 0x000000020 /* Port 5 Enable */
+ #define SH4_PCIPDTR_PB4 0x000000010 /* Port 4 Enable */
+ #define SH4_PCIPDTR_PB3 0x000000008 /* Port 3 Enable */
+ #define SH4_PCIPDTR_PB2 0x000000004 /* Port 2 Enable */
+ #define SH4_PCIPDTR_PB1 0x000000002 /* Port 1 Enable */
+ #define SH4_PCIPDTR_PB0 0x000000001 /* Port 0 Enable */
+#define SH4_PCIPDR 0x220 /* Port IO Data Register */
+
+/* Platform Specific Values */
+#define SH7751_VENDOR_ID 0x1054
+#define SH7751_DEVICE_ID 0x3505
+#define SH7751R_DEVICE_ID 0x350e
+
+/* SH7751 Specific Values */
+#define SH7751_PCI_CONFIG_BASE 0xFD000000 /* Config space base addr */
+#define SH7751_PCI_CONFIG_SIZE 0x1000000 /* Config space size */
+#define SH7751_PCI_MEMORY_BASE 0xFD000000 /* Memory space base addr */
+#define SH7751_PCI_MEM_SIZE 0x01000000 /* Size of Memory window */
+#define SH7751_PCI_IO_BASE 0xFE240000 /* IO space base address */
+#define SH7751_PCI_IO_SIZE 0x40000 /* Size of IO window */
+
+#define SH7751_PCIREG_BASE 0xFE200000 /* PCI regs base address */
+
+#define SH7751_PCICONF0 0x0 /* PCI Config Reg 0 */
+ #define SH7751_PCICONF0_DEVID 0xFFFF0000 /* Device ID */
+ #define SH7751_PCICONF0_VNDID 0x0000FFFF /* Vendor ID */
+#define SH7751_PCICONF1 0x4 /* PCI Config Reg 1 */
+ #define SH7751_PCICONF1_DPE 0x80000000 /* Data Parity Error */
+ #define SH7751_PCICONF1_SSE 0x40000000 /* System Error Status */
+ #define SH7751_PCICONF1_RMA 0x20000000 /* Master Abort */
+ #define SH7751_PCICONF1_RTA 0x10000000 /* Target Abort Rx Status */
+ #define SH7751_PCICONF1_STA 0x08000000 /* Target Abort Exec Status */
+ #define SH7751_PCICONF1_DEV 0x06000000 /* Timing Status */
+ #define SH7751_PCICONF1_DPD 0x01000000 /* Data Parity Status */
+ #define SH7751_PCICONF1_FBBC 0x00800000 /* Back 2 Back Status */
+ #define SH7751_PCICONF1_UDF 0x00400000 /* User Defined Status */
+ #define SH7751_PCICONF1_66M 0x00200000 /* 66Mhz Operation Status */
+ #define SH7751_PCICONF1_PM 0x00100000 /* Power Management Status */
+ #define SH7751_PCICONF1_PBBE 0x00000200 /* Back 2 Back Control */
+ #define SH7751_PCICONF1_SER 0x00000100 /* SERR Output Control */
+ #define SH7751_PCICONF1_WCC 0x00000080 /* Wait Cycle Control */
+ #define SH7751_PCICONF1_PER 0x00000040 /* Parity Error Response */
+ #define SH7751_PCICONF1_VPS 0x00000020 /* VGA Pallet Snoop */
+ #define SH7751_PCICONF1_MWIE 0x00000010 /* Memory Write+Invalidate */
+ #define SH7751_PCICONF1_SPC 0x00000008 /* Special Cycle Control */
+ #define SH7751_PCICONF1_BUM 0x00000004 /* Bus Master Control */
+ #define SH7751_PCICONF1_MES 0x00000002 /* Memory Space Control */
+ #define SH7751_PCICONF1_IOS 0x00000001 /* I/O Space Control */
+#define SH7751_PCICONF2 0x8 /* PCI Config Reg 2 */
+ #define SH7751_PCICONF2_BCC 0xFF000000 /* Base Class Code */
+ #define SH7751_PCICONF2_SCC 0x00FF0000 /* Sub-Class Code */
+ #define SH7751_PCICONF2_RLPI 0x0000FF00 /* Programming Interface */
+ #define SH7751_PCICONF2_REV 0x000000FF /* Revision ID */
+#define SH7751_PCICONF3 0xC /* PCI Config Reg 3 */
+ #define SH7751_PCICONF3_BIST7 0x80000000 /* Bist Supported */
+ #define SH7751_PCICONF3_BIST6 0x40000000 /* Bist Executing */
+ #define SH7751_PCICONF3_BIST3_0 0x0F000000 /* Bist Passed */
+ #define SH7751_PCICONF3_HD7 0x00800000 /* Single Function device */
+ #define SH7751_PCICONF3_HD6_0 0x007F0000 /* Configuration Layout */
+ #define SH7751_PCICONF3_LAT 0x0000FF00 /* Latency Timer */
+ #define SH7751_PCICONF3_CLS 0x000000FF /* Cache Line Size */
+#define SH7751_PCICONF4 0x10 /* PCI Config Reg 4 */
+ #define SH7751_PCICONF4_BASE 0xFFFFFFFC /* I/O Space Base Addr */
+ #define SH7751_PCICONF4_ASI 0x00000001 /* Address Space Type */
+#define SH7751_PCICONF5 0x14 /* PCI Config Reg 5 */
+ #define SH7751_PCICONF5_BASE 0xFFFFFFF0 /* Mem Space Base Addr */
+ #define SH7751_PCICONF5_LAP 0x00000008 /* Prefetch Enabled */
+ #define SH7751_PCICONF5_LAT 0x00000006 /* Local Memory type */
+ #define SH7751_PCICONF5_ASI 0x00000001 /* Address Space Type */
+#define SH7751_PCICONF6 0x18 /* PCI Config Reg 6 */
+ #define SH7751_PCICONF6_BASE 0xFFFFFFF0 /* Mem Space Base Addr */
+ #define SH7751_PCICONF6_LAP 0x00000008 /* Prefetch Enabled */
+ #define SH7751_PCICONF6_LAT 0x00000006 /* Local Memory type */
+ #define SH7751_PCICONF6_ASI 0x00000001 /* Address Space Type */
+/* PCICONF7 - PCICONF10 are undefined */
+#define SH7751_PCICONF11 0x2C /* PCI Config Reg 11 */
+ #define SH7751_PCICONF11_SSID 0xFFFF0000 /* Subsystem ID */
+ #define SH7751_PCICONF11_SVID 0x0000FFFF /* Subsystem Vendor ID */
+/* PCICONF12 is undefined */
+#define SH7751_PCICONF13 0x34 /* PCI Config Reg 13 */
+ #define SH7751_PCICONF13_CPTR 0x000000FF /* PM function pointer */
+/* PCICONF14 is undefined */
+#define SH7751_PCICONF15 0x3C /* PCI Config Reg 15 */
+ #define SH7751_PCICONF15_IPIN 0x000000FF /* Interrupt Pin */
+#define SH7751_PCICONF16 0x40 /* PCI Config Reg 16 */
+ #define SH7751_PCICONF16_PMES 0xF8000000 /* PME Support */
+ #define SH7751_PCICONF16_D2S 0x04000000 /* D2 Support */
+ #define SH7751_PCICONF16_D1S 0x02000000 /* D1 Support */
+ #define SH7751_PCICONF16_DSI 0x00200000 /* Bit Device Init. */
+ #define SH7751_PCICONF16_PMCK 0x00080000 /* Clock for PME req. */
+ #define SH7751_PCICONF16_VER 0x00070000 /* PM Version */
+ #define SH7751_PCICONF16_NIP 0x0000FF00 /* Next Item Pointer */
+ #define SH7751_PCICONF16_CID 0x000000FF /* Capability Identifier */
+#define SH7751_PCICONF17 0x44 /* PCI Config Reg 17 */
+ #define SH7751_PCICONF17_DATA 0xFF000000 /* Data field for PM */
+ #define SH7751_PCICONF17_PMES 0x00800000 /* PME Status */
+ #define SH7751_PCICONF17_DSCL 0x00600000 /* Data Scaling Value */
+ #define SH7751_PCICONF17_DSEL 0x001E0000 /* Data Select */
+ #define SH7751_PCICONF17_PMEN 0x00010000 /* PME Enable */
+ #define SH7751_PCICONF17_PWST 0x00000003 /* Power State */
+/* SH7751 Internal PCI Registers */
+
+/* Memory Control Registers */
+#define SH7751_BCR1 0x0000 /* Memory BCR1 Register */
+#define SH7751_BCR2 0x0004 /* Memory BCR2 Register */
+#define SH7751_BCR3 0x0050 /* Memory BCR3 Register */
+#define SH7751_WCR1 0x0008 /* Wait Control 1 Register */
+#define SH7751_WCR2 0x000C /* Wait Control 2 Register */
+#define SH7751_WCR3 0x0010 /* Wait Control 3 Register */
+#define SH7751_MCR 0x0014 /* Memory Control Register */
+
+/* General Memory Config Addresses */
+#define SH7751_CS0_BASE_ADDR 0x0
+#define SH7751_MEM_REGION_SIZE 0x04000000
+#define SH7751_CS1_BASE_ADDR (SH7751_CS0_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS2_BASE_ADDR (SH7751_CS1_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS3_BASE_ADDR (SH7751_CS2_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS4_BASE_ADDR (SH7751_CS3_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS5_BASE_ADDR (SH7751_CS4_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS6_BASE_ADDR (SH7751_CS5_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+
+#endif /* _PCI_SH7751_H_ */
pci-sh7751.h move from "arch/sh/drivers/pci/pci-sh7751.h" pci-sh7751.c convert from "arch/sh/drivers/pci/pci-sh7751.c" Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp> --- drivers/pci/controller/Kconfig | 9 + drivers/pci/controller/Makefile | 1 + drivers/pci/controller/pci-sh7751.c | 285 ++++++++++++++++++++++++++++ drivers/pci/controller/pci-sh7751.h | 267 ++++++++++++++++++++++++++ 4 files changed, 562 insertions(+) create mode 100644 drivers/pci/controller/pci-sh7751.c create mode 100644 drivers/pci/controller/pci-sh7751.h