Message ID | 20231224050657.182022-3-haifeng.zhao@linux.intel.com (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | fix vt-d hard lockup when hotplug ATS capable device | expand |
On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: > --- a/drivers/iommu/intel/pasid.c > +++ b/drivers/iommu/intel/pasid.c > @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, > if (!info || !info->ats_enabled) > return; > > + if (pci_dev_is_disconnected(to_pci_dev(dev))) > + return; > + > sid = info->bus << 8 | info->devfn; > qdep = info->ats_qdep; > pfsid = info->pfsid; Do you even need this or is patch [4/4] sufficient? Is there a benefit to the hunk above on top of patch [4/4]? Thanks, Lukas
On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: > For those endpoint devices connect to system via hotplug capable ports, > users could request a warm reset to the device by flapping device's link > through setting the slot's link control register, as pciehpt_ist() DLLSC > interrupt sequence response, pciehp will unload the device driver and > then power it off. thus cause an IOMMU devTLB flush request for device to > be sent and a long time completion/timeout waiting in interrupt context. s/don's/don't/ (in subject) s/pciehpt_ist/pciehp_ist/ IIUC you are referring to a specific PCIe transaction, so unless there's another spec that defines "devTLB flush request", please use the actual PCIe transaction name ("ATS Invalidate Request") as Lukas suggested. There's no point in using an informal name that we assume "all iommu/PCIe guys could understand." It's better to use a term that anybody can find by searching the spec. > That would cause following continuous hard lockup warning and system hang > > [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down > [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present > [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 > [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S > OE kernel version xxxx > [ 4223.822623] Hardware name: vendorname xxxx 666-106, > BIOS 01.01.02.03.01 05/15/2023 > [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 > [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b > 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1 > 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 > [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 > [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 > [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 > [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 > [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 > [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 > [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) > knlGS:0000000000000000 > [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0 > [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 > [ 4223.822628] PKRU: 55555554 > [ 4223.822628] Call Trace: > [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 > [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 > [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 > [ 4223.822629] intel_iommu_release_device+0x1f/0x30 > [ 4223.822629] iommu_release_device+0x33/0x60 > [ 4223.822629] iommu_bus_notifier+0x7f/0x90 > [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 > [ 4223.822630] device_del+0x2e5/0x420 > [ 4223.822630] pci_remove_bus_device+0x70/0x110 > [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 > [ 4223.822631] pciehp_disable_slot+0x6b/0x100 > [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 > [ 4223.822631] pciehp_ist+0x176/0x180 > [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 > [ 4223.822632] irq_thread_fn+0x19/0x50 > [ 4223.822632] irq_thread+0x104/0x190 > [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 > [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 > [ 4223.822633] kthread+0x114/0x130 > [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 > [ 4223.822633] ret_from_fork+0x1f/0x30 > [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP > [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S > OE kernel version xxxx > [ 4223.822634] Hardware name: vendorname xxxx 666-106, > BIOS 01.01.02.03.01 05/15/2023 > [ 4223.822634] Call Trace: > [ 4223.822634] <NMI> > [ 4223.822635] dump_stack+0x6d/0x88 > [ 4223.822635] panic+0x101/0x2d0 > [ 4223.822635] ? ret_from_fork+0x11/0x30 > [ 4223.822635] nmi_panic.cold.14+0xc/0xc > [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 > [ 4223.822636] __perf_event_overflow+0x4f/0xf0 > [ 4223.822636] handle_pmi_common+0x1ef/0x290 > [ 4223.822636] ? __set_pte_vaddr+0x28/0x40 > [ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20 > [ 4223.822637] ? __native_set_fixmap+0x24/0x30 > [ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100 > [ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0 > [ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0 > [ 4223.822638] perf_event_nmi_handler+0x24/0x40 > [ 4223.822638] nmi_handle+0x4d/0xf0 > [ 4223.822638] default_do_nmi+0x49/0x100 > [ 4223.822638] exc_nmi+0x134/0x180 > [ 4223.822639] end_repeat_nmi+0x16/0x67 > [ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490 > [ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b > 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 10 > 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 > [ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 > [ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 > [ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 > [ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 > [ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 > [ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 > [ 4223.822641] ? qi_submit_sync+0x2c0/0x490 > [ 4223.822642] ? qi_submit_sync+0x2c0/0x490 > [ 4223.822642] </NMI> > [ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0 > [ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250 > [ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50 > [ 4223.822643] intel_iommu_release_device+0x1f/0x30 > [ 4223.822643] iommu_release_device+0x33/0x60 > [ 4223.822643] iommu_bus_notifier+0x7f/0x90 > [ 4223.822644] blocking_notifier_call_chain+0x60/0x90 > [ 4223.822644] device_del+0x2e5/0x420 > [ 4223.822644] pci_remove_bus_device+0x70/0x110 > [ 4223.822644] pciehp_unconfigure_device+0x7c/0x130 > [ 4223.822644] pciehp_disable_slot+0x6b/0x100 > [ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320 > [ 4223.822645] pciehp_ist+0x176/0x180 > [ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110 > [ 4223.822645] irq_thread_fn+0x19/0x50 > [ 4223.822646] irq_thread+0x104/0x190 > [ 4223.822646] ? irq_forced_thread_fn+0x90/0x90 > [ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0 > [ 4223.822646] kthread+0x114/0x130 > [ 4223.822647] ? __kthread_cancel_work+0x40/0x40 > [ 4223.822647] ret_from_fork+0x1f/0x30 > [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation > range: 0xffffffff80000000-0xffffffffbfffffff) The timestamps don't help understand the problem, so you could remove them so they aren't a distraction. > Fix it by checking the device's error_state in > devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush > request to link down device that is set to pci_channel_io_perm_failure and > then powered off in A pci_dev_is_disconnected() is racy in this context, so this by itself doesn't look like a complete "fix". > pciehp_ist() > pciehp_handle_presence_or_link_change() > pciehp_disable_slot() > remove_board() > pciehp_unconfigure_device() There are some interesting steps missing here between pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate Requests are not Intel-specific, so all IOMMU drivers must have to deal with the case of an ATS Invalidate Request where we never receive a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD and ARM have a similar issue? > For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and > issues devTLB invalidate request, wouldn't trigger such issue. > > This patch works for all links of SURPPRISE_REMOVAL unplug operations. s/devcie/device/ Writing "SAVE_REMOVAL" and "SURPPRISE_REMOVAL" in all caps with an underscore makes them look like identifiers. But neither appears in the kernel source. Write them as normal English words, e.g., "save removal" instead (though I suspect you mean "safe removal"?). s/surpprise/surprise/ It's not completely obvious that a fix that works for the safe removal case also works for the surprise removal case. Can you briefly explain why it does? > Tested-by: Haorong Ye <yehaorong@bytedance.com> > Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> > --- > drivers/iommu/intel/pasid.c | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c > index 74e8e4c17e81..7dbee9931eb6 100644 > --- a/drivers/iommu/intel/pasid.c > +++ b/drivers/iommu/intel/pasid.c > @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, > if (!info || !info->ats_enabled) > return; > > + if (pci_dev_is_disconnected(to_pci_dev(dev))) > + return; > + > sid = info->bus << 8 | info->devfn; > qdep = info->ats_qdep; > pfsid = info->pfsid; This goes on to call qi_submit_sync(), which contains a restart: loop. I don't know the programming model there, but it looks possible that qi_submit_sync() and qi_check_fault() might not handle the case of an unreachable device correctly. There should be a way to exit that restart: loop in cases where the device doesn't respond at all. Bjorn
On 12/24/2023 6:32 PM, Lukas Wunner wrote: > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >> --- a/drivers/iommu/intel/pasid.c >> +++ b/drivers/iommu/intel/pasid.c >> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >> if (!info || !info->ats_enabled) >> return; >> >> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >> + return; >> + >> sid = info->bus << 8 | info->devfn; >> qdep = info->ats_qdep; >> pfsid = info->pfsid; > Do you even need this or is patch [4/4] sufficient? > Is there a benefit to the hunk above on top of patch [4/4]? Need this, I don't want to access config space here, check the flag here is enough, but patch [4/] needs to know if the device is gone by reading device vendor info. Thanks, Ethan > Thanks, > > Lukas
On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >> For those endpoint devices connect to system via hotplug capable ports, >> users could request a warm reset to the device by flapping device's link >> through setting the slot's link control register, as pciehpt_ist() DLLSC >> interrupt sequence response, pciehp will unload the device driver and >> then power it off. thus cause an IOMMU devTLB flush request for device to >> be sent and a long time completion/timeout waiting in interrupt context. > s/don's/don't/ (in subject) > s/pciehpt_ist/pciehp_ist/ > > IIUC you are referring to a specific PCIe transaction, so unless > there's another spec that defines "devTLB flush request", please use > the actual PCIe transaction name ("ATS Invalidate Request") as Lukas > suggested. > > There's no point in using an informal name that we assume "all > iommu/PCIe guys could understand." It's better to use a term that > anybody can find by searching the spec. agree. will revise them together. Thanks, Ethan > >> That would cause following continuous hard lockup warning and system hang >> >> [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down >> [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present >> [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 >> [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822623] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1 >> 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) >> knlGS:0000000000000000 >> [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 >> [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0 >> [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 >> [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 >> [ 4223.822628] PKRU: 55555554 >> [ 4223.822628] Call Trace: >> [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822629] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822629] iommu_release_device+0x33/0x60 >> [ 4223.822629] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822630] device_del+0x2e5/0x420 >> [ 4223.822630] pci_remove_bus_device+0x70/0x110 >> [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822631] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822631] pciehp_ist+0x176/0x180 >> [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822632] irq_thread_fn+0x19/0x50 >> [ 4223.822632] irq_thread+0x104/0x190 >> [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822633] kthread+0x114/0x130 >> [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822633] ret_from_fork+0x1f/0x30 >> [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP >> [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822634] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822634] Call Trace: >> [ 4223.822634] <NMI> >> [ 4223.822635] dump_stack+0x6d/0x88 >> [ 4223.822635] panic+0x101/0x2d0 >> [ 4223.822635] ? ret_from_fork+0x11/0x30 >> [ 4223.822635] nmi_panic.cold.14+0xc/0xc >> [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 >> [ 4223.822636] __perf_event_overflow+0x4f/0xf0 >> [ 4223.822636] handle_pmi_common+0x1ef/0x290 >> [ 4223.822636] ? __set_pte_vaddr+0x28/0x40 >> [ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20 >> [ 4223.822637] ? __native_set_fixmap+0x24/0x30 >> [ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100 >> [ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0 >> [ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0 >> [ 4223.822638] perf_event_nmi_handler+0x24/0x40 >> [ 4223.822638] nmi_handle+0x4d/0xf0 >> [ 4223.822638] default_do_nmi+0x49/0x100 >> [ 4223.822638] exc_nmi+0x134/0x180 >> [ 4223.822639] end_repeat_nmi+0x16/0x67 >> [ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 10 >> 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822641] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] </NMI> >> [ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822643] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822643] iommu_release_device+0x33/0x60 >> [ 4223.822643] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822644] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822644] device_del+0x2e5/0x420 >> [ 4223.822644] pci_remove_bus_device+0x70/0x110 >> [ 4223.822644] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822644] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822645] pciehp_ist+0x176/0x180 >> [ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822645] irq_thread_fn+0x19/0x50 >> [ 4223.822646] irq_thread+0x104/0x190 >> [ 4223.822646] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822646] kthread+0x114/0x130 >> [ 4223.822647] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822647] ret_from_fork+0x1f/0x30 >> [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation >> range: 0xffffffff80000000-0xffffffffbfffffff) > The timestamps don't help understand the problem, so you could remove > them so they aren't a distraction. > >> Fix it by checking the device's error_state in >> devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush >> request to link down device that is set to pci_channel_io_perm_failure and >> then powered off in > A pci_dev_is_disconnected() is racy in this context, so this by itself > doesn't look like a complete "fix". > >> pciehp_ist() >> pciehp_handle_presence_or_link_change() >> pciehp_disable_slot() >> remove_board() >> pciehp_unconfigure_device() > There are some interesting steps missing here between > pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). > > devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate > Requests are not Intel-specific, so all IOMMU drivers must have to > deal with the case of an ATS Invalidate Request where we never receive > a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD > and ARM have a similar issue? > >> For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and >> issues devTLB invalidate request, wouldn't trigger such issue. >> >> This patch works for all links of SURPPRISE_REMOVAL unplug operations. > s/devcie/device/ > > Writing "SAVE_REMOVAL" and "SURPPRISE_REMOVAL" in all caps with an > underscore makes them look like identifiers. But neither appears in > the kernel source. Write them as normal English words, e.g., "save > removal" instead (though I suspect you mean "safe removal"?). > > s/surpprise/surprise/ > > It's not completely obvious that a fix that works for the safe removal > case also works for the surprise removal case. Can you briefly > explain why it does? > >> Tested-by: Haorong Ye <yehaorong@bytedance.com> >> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> >> --- >> drivers/iommu/intel/pasid.c | 3 +++ >> 1 file changed, 3 insertions(+) >> >> diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c >> index 74e8e4c17e81..7dbee9931eb6 100644 >> --- a/drivers/iommu/intel/pasid.c >> +++ b/drivers/iommu/intel/pasid.c >> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >> if (!info || !info->ats_enabled) >> return; >> >> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >> + return; >> + >> sid = info->bus << 8 | info->devfn; >> qdep = info->ats_qdep; >> pfsid = info->pfsid; > This goes on to call qi_submit_sync(), which contains a restart: loop. > I don't know the programming model there, but it looks possible that > qi_submit_sync() and qi_check_fault() might not handle the case of an > unreachable device correctly. There should be a way to exit that > restart: loop in cases where the device doesn't respond at all. > > Bjorn
On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >> For those endpoint devices connect to system via hotplug capable ports, >> users could request a warm reset to the device by flapping device's link >> through setting the slot's link control register, as pciehpt_ist() DLLSC >> interrupt sequence response, pciehp will unload the device driver and >> then power it off. thus cause an IOMMU devTLB flush request for device to >> be sent and a long time completion/timeout waiting in interrupt context. > s/don's/don't/ (in subject) > s/pciehpt_ist/pciehp_ist/ > > IIUC you are referring to a specific PCIe transaction, so unless > there's another spec that defines "devTLB flush request", please use > the actual PCIe transaction name ("ATS Invalidate Request") as Lukas > suggested. > > There's no point in using an informal name that we assume "all > iommu/PCIe guys could understand." It's better to use a term that > anybody can find by searching the spec. > >> That would cause following continuous hard lockup warning and system hang >> >> [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down >> [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present >> [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 >> [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822623] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1 >> 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) >> knlGS:0000000000000000 >> [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 >> [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0 >> [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 >> [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 >> [ 4223.822628] PKRU: 55555554 >> [ 4223.822628] Call Trace: >> [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822629] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822629] iommu_release_device+0x33/0x60 >> [ 4223.822629] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822630] device_del+0x2e5/0x420 >> [ 4223.822630] pci_remove_bus_device+0x70/0x110 >> [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822631] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822631] pciehp_ist+0x176/0x180 >> [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822632] irq_thread_fn+0x19/0x50 >> [ 4223.822632] irq_thread+0x104/0x190 >> [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822633] kthread+0x114/0x130 >> [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822633] ret_from_fork+0x1f/0x30 >> [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP >> [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822634] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822634] Call Trace: >> [ 4223.822634] <NMI> >> [ 4223.822635] dump_stack+0x6d/0x88 >> [ 4223.822635] panic+0x101/0x2d0 >> [ 4223.822635] ? ret_from_fork+0x11/0x30 >> [ 4223.822635] nmi_panic.cold.14+0xc/0xc >> [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 >> [ 4223.822636] __perf_event_overflow+0x4f/0xf0 >> [ 4223.822636] handle_pmi_common+0x1ef/0x290 >> [ 4223.822636] ? __set_pte_vaddr+0x28/0x40 >> [ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20 >> [ 4223.822637] ? __native_set_fixmap+0x24/0x30 >> [ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100 >> [ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0 >> [ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0 >> [ 4223.822638] perf_event_nmi_handler+0x24/0x40 >> [ 4223.822638] nmi_handle+0x4d/0xf0 >> [ 4223.822638] default_do_nmi+0x49/0x100 >> [ 4223.822638] exc_nmi+0x134/0x180 >> [ 4223.822639] end_repeat_nmi+0x16/0x67 >> [ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 10 >> 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822641] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] </NMI> >> [ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822643] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822643] iommu_release_device+0x33/0x60 >> [ 4223.822643] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822644] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822644] device_del+0x2e5/0x420 >> [ 4223.822644] pci_remove_bus_device+0x70/0x110 >> [ 4223.822644] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822644] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822645] pciehp_ist+0x176/0x180 >> [ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822645] irq_thread_fn+0x19/0x50 >> [ 4223.822646] irq_thread+0x104/0x190 >> [ 4223.822646] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822646] kthread+0x114/0x130 >> [ 4223.822647] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822647] ret_from_fork+0x1f/0x30 >> [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation >> range: 0xffffffff80000000-0xffffffffbfffffff) > The timestamps don't help understand the problem, so you could remove > them so they aren't a distraction. Lukas said he see the qi_submit_sync takes up to 12 seconds to trigger the watchdog. > >> Fix it by checking the device's error_state in >> devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush >> request to link down device that is set to pci_channel_io_perm_failure and >> then powered off in > A pci_dev_is_disconnected() is racy in this context, so this by itself > doesn't look like a complete "fix". A quick workaround. >> pciehp_ist() >> pciehp_handle_presence_or_link_change() >> pciehp_disable_slot() >> remove_board() >> pciehp_unconfigure_device() > There are some interesting steps missing here between > pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). > > devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate > Requests are not Intel-specific, so all IOMMU drivers must have to > deal with the case of an ATS Invalidate Request where we never receive > a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD > and ARM have a similar issue? So far fix it in Intel vt-d specific path. >> For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and >> issues devTLB invalidate request, wouldn't trigger such issue. >> >> This patch works for all links of SURPPRISE_REMOVAL unplug operations. > s/devcie/device/ got it. > > Writing "SAVE_REMOVAL" and "SURPPRISE_REMOVAL" in all caps with an > underscore makes them look like identifiers. But neither appears in > the kernel source. Write them as normal English words, e.g., "save > removal" instead (though I suspect you mean "safe removal"?). > > s/surpprise/surprise/ > > It's not completely obvious that a fix that works for the safe removal > case also works for the surprise removal case. Can you briefly > explain why it does? As I explained to baolu. For safe_removal, device wouldn't be removed till the whole software handling process done, so without this fix, it wouldn't trigger the lockup issue, and in safe_removal path, device state isn't set to pci_channel_io_perm_failure in pciehp_unconfigure_device() by checking 'presence', patch calling this pci_dev_is_disconnected() will return false there, wouldn't break the function. so it works. For suprise_removal, device state is set to pci_channel_io_perm_failure in pciehp_unconfigure_device(), means device already be in power-off/link-down /removed state, callpci_dev_is_disconnected() hrere will return true to break the function not to send ATS invalidation request anymore, thus avoid the further long time waiting trigger the hard lockup. Do I make it clear enough ? >> Tested-by: Haorong Ye <yehaorong@bytedance.com> >> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> >> --- >> drivers/iommu/intel/pasid.c | 3 +++ >> 1 file changed, 3 insertions(+) >> >> diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c >> index 74e8e4c17e81..7dbee9931eb6 100644 >> --- a/drivers/iommu/intel/pasid.c >> +++ b/drivers/iommu/intel/pasid.c >> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >> if (!info || !info->ats_enabled) >> return; >> >> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >> + return; >> + >> sid = info->bus << 8 | info->devfn; >> qdep = info->ats_qdep; >> pfsid = info->pfsid; > This goes on to call qi_submit_sync(), which contains a restart: loop. > I don't know the programming model there, but it looks possible that > qi_submit_sync() and qi_check_fault() might not handle the case of an > unreachable device correctly. There should be a way to exit that > restart: loop in cases where the device doesn't respond at all. Yes, fix it in patch[4/4] to break it out when device is gone. Thanks, Ethan > > Bjorn
On 12/24/2023 6:32 PM, Lukas Wunner wrote: > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >> --- a/drivers/iommu/intel/pasid.c >> +++ b/drivers/iommu/intel/pasid.c >> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >> if (!info || !info->ats_enabled) >> return; >> >> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >> + return; >> + >> sid = info->bus << 8 | info->devfn; >> qdep = info->ats_qdep; >> pfsid = info->pfsid; > Do you even need this or is patch [4/4] sufficient? > Is there a benefit to the hunk above on top of patch [4/4]? this is enough for purely surprise_removal or safe_removal, it is better to not send "ATS invalidation request" than sent, then check device state later. Thanks, Ethan > Thanks, > > Lukas >
On Mon, Dec 25, 2023 at 09:46:26AM +0800, Ethan Zhao wrote: > On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: > > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: > > > ... > > > [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down > > > [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present > > > [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 > > > ... > > > [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation > > > range: 0xffffffff80000000-0xffffffffbfffffff) > > > > The timestamps don't help understand the problem, so you could remove > > them so they aren't a distraction. > > Lukas said he see the qi_submit_sync takes up to 12 seconds to trigger the > watchdog. OK, so the timestamps told us how long the watchdog tolerates. I don't know how useful that is. I suspect that's not a fixed interval (probably differs by watchdog and possibly user preference). > > > Fix it by checking the device's error_state in > > > devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush > > > request to link down device that is set to pci_channel_io_perm_failure and > > > then powered off in > > > > A pci_dev_is_disconnected() is racy in this context, so this by itself > > doesn't look like a complete "fix". > > A quick workaround. Call it a "quick workaround" then, not a "fix". I'm personally not usually interested in quick workarounds that are not actually fixes, but the IOMMU folks would be the ones to decide. Maybe this is more of an optimization? If patch 4/4 is a real fix (in the sense that if you disable the watchdog, you would get correct results after a long timeout), maybe you could reorder the patches so 4/4 comes first, and this one becomes an optimization on top of it? I haven't worked though the whole path, so I don't know exactly how these patches work. > > > pciehp_ist() > > > pciehp_handle_presence_or_link_change() > > > pciehp_disable_slot() > > > remove_board() > > > pciehp_unconfigure_device() > > There are some interesting steps missing here between > > pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). > > > > devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate > > Requests are not Intel-specific, so all IOMMU drivers must have to > > deal with the case of an ATS Invalidate Request where we never receive > > a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD > > and ARM have a similar issue? > > So far fix it in Intel vt-d specific path. If the other IOMMU drivers are vulnerable, I guess they would like to fix this at the same time and in a similar way if possible. > > > For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and > > > issues devTLB invalidate request, wouldn't trigger such issue. > > > > > > This patch works for all links of SURPPRISE_REMOVAL unplug operations. > > It's not completely obvious that a fix that works for the safe removal > > case also works for the surprise removal case. Can you briefly > > explain why it does? > > As I explained to baolu. > > For safe_removal, device wouldn't be removed till the whole software > handling process done, so without this fix, it wouldn't trigger the lockup > issue, and in safe_removal path, device state isn't set to > pci_channel_io_perm_failure in pciehp_unconfigure_device() by checking > 'presence', patch calling this pci_dev_is_disconnected() will return false > there, wouldn't break the function. so it works. > > For suprise_removal, device state is set to pci_channel_io_perm_failure in > pciehp_unconfigure_device(), means device already be in power-off/link-down > /removed state, callpci_dev_is_disconnected() hrere will return true to > break > > the function not to send ATS invalidation request anymore, thus avoid the > further long time waiting trigger the hard lockup. s/safe_removal/safe removal/ (they are not a single word) s/suprise_removal/surprise removal/ (misspelled, also not a single word) > Do I make it clear enough ? Needs to be in the commit log, of course. > > > Tested-by: Haorong Ye <yehaorong@bytedance.com> > > > Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> > > > --- > > > drivers/iommu/intel/pasid.c | 3 +++ > > > 1 file changed, 3 insertions(+) > > > > > > diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c > > > index 74e8e4c17e81..7dbee9931eb6 100644 > > > --- a/drivers/iommu/intel/pasid.c > > > +++ b/drivers/iommu/intel/pasid.c > > > @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, > > > if (!info || !info->ats_enabled) > > > return; > > > + if (pci_dev_is_disconnected(to_pci_dev(dev))) > > > + return; > > > + > > > sid = info->bus << 8 | info->devfn; > > > qdep = info->ats_qdep; > > > pfsid = info->pfsid; > > > > This goes on to call qi_submit_sync(), which contains a restart: loop. > > I don't know the programming model there, but it looks possible that > > qi_submit_sync() and qi_check_fault() might not handle the case of an > > unreachable device correctly. There should be a way to exit that > > restart: loop in cases where the device doesn't respond at all. > > Yes, fix it in patch[4/4] to break it out when device is gone.
On 12/25/2023 10:21 AM, Bjorn Helgaas wrote: > On Mon, Dec 25, 2023 at 09:46:26AM +0800, Ethan Zhao wrote: >> On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: >>> On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >>>> ... >>>> [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down >>>> [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present >>>> [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 >>>> ... >>>> [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation >>>> range: 0xffffffff80000000-0xffffffffbfffffff) >>> The timestamps don't help understand the problem, so you could remove >>> them so they aren't a distraction. >> Lukas said he see the qi_submit_sync takes up to 12 seconds to trigger the >> watchdog. > OK, so the timestamps told us how long the watchdog tolerates. I > don't know how useful that is. I suspect that's not a fixed interval > (probably differs by watchdog and possibly user preference). > >>>> Fix it by checking the device's error_state in >>>> devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush >>>> request to link down device that is set to pci_channel_io_perm_failure and >>>> then powered off in >>> A pci_dev_is_disconnected() is racy in this context, so this by itself >>> doesn't look like a complete "fix". >> A quick workaround. > Call it a "quick workaround" then, not a "fix". I'm personally not > usually interested in quick workarounds that are not actually fixes, > but the IOMMU folks would be the ones to decide. > > Maybe this is more of an optimization? If patch 4/4 is a real fix (in > the sense that if you disable the watchdog, you would get correct > results after a long timeout), maybe you could reorder the patches so > 4/4 comes first, and this one becomes an optimization on top of it? I Make sense, will reorder them. > haven't worked though the whole path, so I don't know exactly how > these patches work. > >>>> pciehp_ist() >>>> pciehp_handle_presence_or_link_change() >>>> pciehp_disable_slot() >>>> remove_board() >>>> pciehp_unconfigure_device() >>> There are some interesting steps missing here between >>> pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). >>> >>> devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate >>> Requests are not Intel-specific, so all IOMMU drivers must have to >>> deal with the case of an ATS Invalidate Request where we never receive >>> a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD >>> and ARM have a similar issue? >> So far fix it in Intel vt-d specific path. > If the other IOMMU drivers are vulnerable, I guess they would like to > fix this at the same time and in a similar way if possible. > >>>> For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and >>>> issues devTLB invalidate request, wouldn't trigger such issue. >>>> >>>> This patch works for all links of SURPPRISE_REMOVAL unplug operations. >>> It's not completely obvious that a fix that works for the safe removal >>> case also works for the surprise removal case. Can you briefly >>> explain why it does? >> As I explained to baolu. >> >> For safe_removal, device wouldn't be removed till the whole software >> handling process done, so without this fix, it wouldn't trigger the lockup >> issue, and in safe_removal path, device state isn't set to >> pci_channel_io_perm_failure in pciehp_unconfigure_device() by checking >> 'presence', patch calling this pci_dev_is_disconnected() will return false >> there, wouldn't break the function. so it works. >> >> For suprise_removal, device state is set to pci_channel_io_perm_failure in >> pciehp_unconfigure_device(), means device already be in power-off/link-down >> /removed state, callpci_dev_is_disconnected() hrere will return true to >> break >> >> the function not to send ATS invalidation request anymore, thus avoid the >> further long time waiting trigger the hard lockup. > s/safe_removal/safe removal/ (they are not a single word) > s/suprise_removal/surprise removal/ (misspelled, also not a single word) > >> Do I make it clear enough ? > Needs to be in the commit log, of course. Okay, append to the commit log. Thanks, Ethan >>>> Tested-by: Haorong Ye <yehaorong@bytedance.com> >>>> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> >>>> --- >>>> drivers/iommu/intel/pasid.c | 3 +++ >>>> 1 file changed, 3 insertions(+) >>>> >>>> diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c >>>> index 74e8e4c17e81..7dbee9931eb6 100644 >>>> --- a/drivers/iommu/intel/pasid.c >>>> +++ b/drivers/iommu/intel/pasid.c >>>> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >>>> if (!info || !info->ats_enabled) >>>> return; >>>> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >>>> + return; >>>> + >>>> sid = info->bus << 8 | info->devfn; >>>> qdep = info->ats_qdep; >>>> pfsid = info->pfsid; >>> This goes on to call qi_submit_sync(), which contains a restart: loop. >>> I don't know the programming model there, but it looks possible that >>> qi_submit_sync() and qi_check_fault() might not handle the case of an >>> unreachable device correctly. There should be a way to exit that >>> restart: loop in cases where the device doesn't respond at all. >> Yes, fix it in patch[4/4] to break it out when device is gone.
On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: > On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >> For those endpoint devices connect to system via hotplug capable ports, >> users could request a warm reset to the device by flapping device's link >> through setting the slot's link control register, as pciehpt_ist() DLLSC >> interrupt sequence response, pciehp will unload the device driver and >> then power it off. thus cause an IOMMU devTLB flush request for device to >> be sent and a long time completion/timeout waiting in interrupt context. > s/don's/don't/ (in subject) > s/pciehpt_ist/pciehp_ist/ > > IIUC you are referring to a specific PCIe transaction, so unless > there's another spec that defines "devTLB flush request", please use > the actual PCIe transaction name ("ATS Invalidate Request") as Lukas > suggested. > > There's no point in using an informal name that we assume "all > iommu/PCIe guys could understand." It's better to use a term that > anybody can find by searching the spec. > >> That would cause following continuous hard lockup warning and system hang >> >> [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down >> [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present >> [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 >> [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822623] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1 >> 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) >> knlGS:0000000000000000 >> [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 >> [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0 >> [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 >> [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 >> [ 4223.822628] PKRU: 55555554 >> [ 4223.822628] Call Trace: >> [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822629] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822629] iommu_release_device+0x33/0x60 >> [ 4223.822629] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822630] device_del+0x2e5/0x420 >> [ 4223.822630] pci_remove_bus_device+0x70/0x110 >> [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822631] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822631] pciehp_ist+0x176/0x180 >> [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822632] irq_thread_fn+0x19/0x50 >> [ 4223.822632] irq_thread+0x104/0x190 >> [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822633] kthread+0x114/0x130 >> [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822633] ret_from_fork+0x1f/0x30 >> [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP >> [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S >> OE kernel version xxxx >> [ 4223.822634] Hardware name: vendorname xxxx 666-106, >> BIOS 01.01.02.03.01 05/15/2023 >> [ 4223.822634] Call Trace: >> [ 4223.822634] <NMI> >> [ 4223.822635] dump_stack+0x6d/0x88 >> [ 4223.822635] panic+0x101/0x2d0 >> [ 4223.822635] ? ret_from_fork+0x11/0x30 >> [ 4223.822635] nmi_panic.cold.14+0xc/0xc >> [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 >> [ 4223.822636] __perf_event_overflow+0x4f/0xf0 >> [ 4223.822636] handle_pmi_common+0x1ef/0x290 >> [ 4223.822636] ? __set_pte_vaddr+0x28/0x40 >> [ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20 >> [ 4223.822637] ? __native_set_fixmap+0x24/0x30 >> [ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100 >> [ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0 >> [ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0 >> [ 4223.822638] perf_event_nmi_handler+0x24/0x40 >> [ 4223.822638] nmi_handle+0x4d/0xf0 >> [ 4223.822638] default_do_nmi+0x49/0x100 >> [ 4223.822638] exc_nmi+0x134/0x180 >> [ 4223.822639] end_repeat_nmi+0x16/0x67 >> [ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490 >> [ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b >> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 10 >> 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >> [ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >> [ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 >> [ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 >> [ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 >> [ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 >> [ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 >> [ 4223.822641] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] ? qi_submit_sync+0x2c0/0x490 >> [ 4223.822642] </NMI> >> [ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0 >> [ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250 >> [ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50 >> [ 4223.822643] intel_iommu_release_device+0x1f/0x30 >> [ 4223.822643] iommu_release_device+0x33/0x60 >> [ 4223.822643] iommu_bus_notifier+0x7f/0x90 >> [ 4223.822644] blocking_notifier_call_chain+0x60/0x90 >> [ 4223.822644] device_del+0x2e5/0x420 >> [ 4223.822644] pci_remove_bus_device+0x70/0x110 >> [ 4223.822644] pciehp_unconfigure_device+0x7c/0x130 >> [ 4223.822644] pciehp_disable_slot+0x6b/0x100 >> [ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320 >> [ 4223.822645] pciehp_ist+0x176/0x180 >> [ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110 >> [ 4223.822645] irq_thread_fn+0x19/0x50 >> [ 4223.822646] irq_thread+0x104/0x190 >> [ 4223.822646] ? irq_forced_thread_fn+0x90/0x90 >> [ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0 >> [ 4223.822646] kthread+0x114/0x130 >> [ 4223.822647] ? __kthread_cancel_work+0x40/0x40 >> [ 4223.822647] ret_from_fork+0x1f/0x30 >> [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 (relocation >> range: 0xffffffff80000000-0xffffffffbfffffff) > The timestamps don't help understand the problem, so you could remove > them so they aren't a distraction. > >> Fix it by checking the device's error_state in >> devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB flush >> request to link down device that is set to pci_channel_io_perm_failure and >> then powered off in > A pci_dev_is_disconnected() is racy in this context, so this by itself > doesn't look like a complete "fix". > >> pciehp_ist() >> pciehp_handle_presence_or_link_change() >> pciehp_disable_slot() >> remove_board() >> pciehp_unconfigure_device() > There are some interesting steps missing here between > pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). > > devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate > Requests are not Intel-specific, so all IOMMU drivers must have to > deal with the case of an ATS Invalidate Request where we never receive > a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD > and ARM have a similar issue? > >> For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and >> issues devTLB invalidate request, wouldn't trigger such issue. >> >> This patch works for all links of SURPPRISE_REMOVAL unplug operations. > s/devcie/device/ > > Writing "SAVE_REMOVAL" and "SURPPRISE_REMOVAL" in all caps with an > underscore makes them look like identifiers. But neither appears in > the kernel source. Write them as normal English words, e.g., "save > removal" instead (though I suspect you mean "safe removal"?). > > s/surpprise/surprise/ > > It's not completely obvious that a fix that works for the safe removal > case also works for the surprise removal case. Can you briefly > explain why it does? > >> Tested-by: Haorong Ye <yehaorong@bytedance.com> >> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> >> --- >> drivers/iommu/intel/pasid.c | 3 +++ >> 1 file changed, 3 insertions(+) >> >> diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c >> index 74e8e4c17e81..7dbee9931eb6 100644 >> --- a/drivers/iommu/intel/pasid.c >> +++ b/drivers/iommu/intel/pasid.c >> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, >> if (!info || !info->ats_enabled) >> return; >> >> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >> + return; >> + >> sid = info->bus << 8 | info->devfn; >> qdep = info->ats_qdep; >> pfsid = info->pfsid; > This goes on to call qi_submit_sync(), which contains a restart: loop. > I don't know the programming model there, but it looks possible that > qi_submit_sync() and qi_check_fault() might not handle the case of an > unreachable device correctly. There should be a way to exit that > restart: loop in cases where the device doesn't respond at all. Current sychronous model isn't good to handle such case, so does the CPU. the vt-d hardware is integrated, if it is just broken, no response at all, it will block all devices I/O attached to that iommu, then bring down the whole system. except individual iommu and its device tree could be hotplug capable. asynchornouse programming module will work for it. my undestanding. Thanks, Ethan > > Bjorn >
On 12/25/2023 5:12 PM, Ethan Zhao wrote: > > On 12/25/2023 6:43 AM, Bjorn Helgaas wrote: >> On Sun, Dec 24, 2023 at 12:06:55AM -0500, Ethan Zhao wrote: >>> For those endpoint devices connect to system via hotplug capable ports, >>> users could request a warm reset to the device by flapping device's >>> link >>> through setting the slot's link control register, as pciehpt_ist() >>> DLLSC >>> interrupt sequence response, pciehp will unload the device driver and >>> then power it off. thus cause an IOMMU devTLB flush request for >>> device to >>> be sent and a long time completion/timeout waiting in interrupt >>> context. >> s/don's/don't/ (in subject) >> s/pciehpt_ist/pciehp_ist/ >> >> IIUC you are referring to a specific PCIe transaction, so unless >> there's another spec that defines "devTLB flush request", please use >> the actual PCIe transaction name ("ATS Invalidate Request") as Lukas >> suggested. >> >> There's no point in using an informal name that we assume "all >> iommu/PCIe guys could understand." It's better to use a term that >> anybody can find by searching the spec. >> >>> That would cause following continuous hard lockup warning and system >>> hang >>> >>> [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down >>> [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not >>> present >>> [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 >>> [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded >>> Tainted: G S >>> OE kernel version xxxx >>> [ 4223.822623] Hardware name: vendorname xxxx 666-106, >>> BIOS 01.01.02.03.01 05/15/2023 >>> [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 >>> [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f >>> 95 c1 48 8b >>> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 >>> <40> f6 c6 1 >>> 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >>> [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >>> [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: >>> 0000000000000005 >>> [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: >>> ffff9f38401a8340 >>> [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: >>> 0000000000000000 >>> [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: >>> ffff9f384005e200 >>> [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: >>> 0000000000000004 >>> [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) >>> knlGS:0000000000000000 >>> [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 >>> [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: >>> 0000000000770ee0 >>> [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: >>> 0000000000000000 >>> [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: >>> 0000000000000400 >>> [ 4223.822628] PKRU: 55555554 >>> [ 4223.822628] Call Trace: >>> [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 >>> [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 >>> [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 >>> [ 4223.822629] intel_iommu_release_device+0x1f/0x30 >>> [ 4223.822629] iommu_release_device+0x33/0x60 >>> [ 4223.822629] iommu_bus_notifier+0x7f/0x90 >>> [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 >>> [ 4223.822630] device_del+0x2e5/0x420 >>> [ 4223.822630] pci_remove_bus_device+0x70/0x110 >>> [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 >>> [ 4223.822631] pciehp_disable_slot+0x6b/0x100 >>> [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 >>> [ 4223.822631] pciehp_ist+0x176/0x180 >>> [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 >>> [ 4223.822632] irq_thread_fn+0x19/0x50 >>> [ 4223.822632] irq_thread+0x104/0x190 >>> [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 >>> [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 >>> [ 4223.822633] kthread+0x114/0x130 >>> [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 >>> [ 4223.822633] ret_from_fork+0x1f/0x30 >>> [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP >>> [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded >>> Tainted: G S >>> OE kernel version xxxx >>> [ 4223.822634] Hardware name: vendorname xxxx 666-106, >>> BIOS 01.01.02.03.01 05/15/2023 >>> [ 4223.822634] Call Trace: >>> [ 4223.822634] <NMI> >>> [ 4223.822635] dump_stack+0x6d/0x88 >>> [ 4223.822635] panic+0x101/0x2d0 >>> [ 4223.822635] ? ret_from_fork+0x11/0x30 >>> [ 4223.822635] nmi_panic.cold.14+0xc/0xc >>> [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 >>> [ 4223.822636] __perf_event_overflow+0x4f/0xf0 >>> [ 4223.822636] handle_pmi_common+0x1ef/0x290 >>> [ 4223.822636] ? __set_pte_vaddr+0x28/0x40 >>> [ 4223.822637] ? flush_tlb_one_kernel+0xa/0x20 >>> [ 4223.822637] ? __native_set_fixmap+0x24/0x30 >>> [ 4223.822637] ? ghes_copy_tofrom_phys+0x70/0x100 >>> [ 4223.822637] ? __ghes_peek_estatus.isra.16+0x49/0xa0 >>> [ 4223.822637] intel_pmu_handle_irq+0xba/0x2b0 >>> [ 4223.822638] perf_event_nmi_handler+0x24/0x40 >>> [ 4223.822638] nmi_handle+0x4d/0xf0 >>> [ 4223.822638] default_do_nmi+0x49/0x100 >>> [ 4223.822638] exc_nmi+0x134/0x180 >>> [ 4223.822639] end_repeat_nmi+0x16/0x67 >>> [ 4223.822639] RIP: 0010:qi_submit_sync+0x2c0/0x490 >>> [ 4223.822639] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f >>> 95 c1 48 8b >>> 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 >>> <40> f6 c6 10 >>> 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 >>> [ 4223.822640] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 >>> [ 4223.822640] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: >>> 0000000000000005 >>> [ 4223.822640] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: >>> ffff9f38401a8340 >>> [ 4223.822641] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: >>> 0000000000000000 >>> [ 4223.822641] R10: 0000000000000010 R11: 0000000000000018 R12: >>> ffff9f384005e200 >>> [ 4223.822641] R13: 0000000000000004 R14: 0000000000000046 R15: >>> 0000000000000004 >>> [ 4223.822641] ? qi_submit_sync+0x2c0/0x490 >>> [ 4223.822642] ? qi_submit_sync+0x2c0/0x490 >>> [ 4223.822642] </NMI> >>> [ 4223.822642] qi_flush_dev_iotlb+0xb1/0xd0 >>> [ 4223.822642] __dmar_remove_one_dev_info+0x224/0x250 >>> [ 4223.822643] dmar_remove_one_dev_info+0x3e/0x50 >>> [ 4223.822643] intel_iommu_release_device+0x1f/0x30 >>> [ 4223.822643] iommu_release_device+0x33/0x60 >>> [ 4223.822643] iommu_bus_notifier+0x7f/0x90 >>> [ 4223.822644] blocking_notifier_call_chain+0x60/0x90 >>> [ 4223.822644] device_del+0x2e5/0x420 >>> [ 4223.822644] pci_remove_bus_device+0x70/0x110 >>> [ 4223.822644] pciehp_unconfigure_device+0x7c/0x130 >>> [ 4223.822644] pciehp_disable_slot+0x6b/0x100 >>> [ 4223.822645] pciehp_handle_presence_or_link_change+0xd8/0x320 >>> [ 4223.822645] pciehp_ist+0x176/0x180 >>> [ 4223.822645] ? irq_finalize_oneshot.part.50+0x110/0x110 >>> [ 4223.822645] irq_thread_fn+0x19/0x50 >>> [ 4223.822646] irq_thread+0x104/0x190 >>> [ 4223.822646] ? irq_forced_thread_fn+0x90/0x90 >>> [ 4223.822646] ? irq_thread_check_affinity+0xe0/0xe0 >>> [ 4223.822646] kthread+0x114/0x130 >>> [ 4223.822647] ? __kthread_cancel_work+0x40/0x40 >>> [ 4223.822647] ret_from_fork+0x1f/0x30 >>> [ 4223.822647] Kernel Offset: 0x6400000 from 0xffffffff81000000 >>> (relocation >>> range: 0xffffffff80000000-0xffffffffbfffffff) >> The timestamps don't help understand the problem, so you could remove >> them so they aren't a distraction. >> >>> Fix it by checking the device's error_state in >>> devtlb_invalidation_with_pasid() to avoid sending meaningless devTLB >>> flush >>> request to link down device that is set to >>> pci_channel_io_perm_failure and >>> then powered off in >> A pci_dev_is_disconnected() is racy in this context, so this by itself >> doesn't look like a complete "fix". >> >>> pciehp_ist() >>> pciehp_handle_presence_or_link_change() >>> pciehp_disable_slot() >>> remove_board() >>> pciehp_unconfigure_device() >> There are some interesting steps missing here between >> pciehp_unconfigure_device() and devtlb_invalidation_with_pasid(). >> >> devtlb_invalidation_with_pasid() is Intel-specific. ATS Invalidate >> Requests are not Intel-specific, so all IOMMU drivers must have to >> deal with the case of an ATS Invalidate Request where we never receive >> a corresponding ATS Invalidate Completion. Do other IOMMUs like AMD >> and ARM have a similar issue? >> >>> For SAVE_REMOVAL unplug, link is alive when iommu releases devcie and >>> issues devTLB invalidate request, wouldn't trigger such issue. >>> >>> This patch works for all links of SURPPRISE_REMOVAL unplug operations. >> s/devcie/device/ >> >> Writing "SAVE_REMOVAL" and "SURPPRISE_REMOVAL" in all caps with an >> underscore makes them look like identifiers. But neither appears in >> the kernel source. Write them as normal English words, e.g., "save >> removal" instead (though I suspect you mean "safe removal"?). >> >> s/surpprise/surprise/ >> >> It's not completely obvious that a fix that works for the safe removal >> case also works for the surprise removal case. Can you briefly >> explain why it does? >> >>> Tested-by: Haorong Ye <yehaorong@bytedance.com> >>> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> >>> --- >>> drivers/iommu/intel/pasid.c | 3 +++ >>> 1 file changed, 3 insertions(+) >>> >>> diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c >>> index 74e8e4c17e81..7dbee9931eb6 100644 >>> --- a/drivers/iommu/intel/pasid.c >>> +++ b/drivers/iommu/intel/pasid.c >>> @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct >>> intel_iommu *iommu, >>> if (!info || !info->ats_enabled) >>> return; >>> + if (pci_dev_is_disconnected(to_pci_dev(dev))) >>> + return; >>> + >>> sid = info->bus << 8 | info->devfn; >>> qdep = info->ats_qdep; >>> pfsid = info->pfsid; >> This goes on to call qi_submit_sync(), which contains a restart: loop. >> I don't know the programming model there, but it looks possible that >> qi_submit_sync() and qi_check_fault() might not handle the case of an >> unreachable device correctly. There should be a way to exit that >> restart: loop in cases where the device doesn't respond at all. > > Current sychronous model isn't good to handle such case, so does > > the CPU. the vt-d hardware is integrated, if it is just broken, no > response > > at all, it will block all devices I/O attached to that iommu, then > bring down > > the whole system. except individual iommu and its device tree could be > > hotplug capable. asynchornouse programming module will work for it. > > my undestanding. > > Add another patch in v8, try to break the timeout invalidation loop if the endpoint device just no response, but not gone (present). thanks for your tip about the no response case. Thanks, Ethan > Thanks, > > Ethan > >> >> Bjorn >> >
diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c index 74e8e4c17e81..7dbee9931eb6 100644 --- a/drivers/iommu/intel/pasid.c +++ b/drivers/iommu/intel/pasid.c @@ -481,6 +481,9 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, if (!info || !info->ats_enabled) return; + if (pci_dev_is_disconnected(to_pci_dev(dev))) + return; + sid = info->bus << 8 | info->devfn; qdep = info->ats_qdep; pfsid = info->pfsid;