diff mbox series

[v4,05/12] wifi: ath12k: scan statemachine changes for single wiphy

Message ID 20240312135557.1778379-6-quic_ramess@quicinc.com (mailing list archive)
State Changes Requested
Delegated to: Kalle Valo
Headers show
Series wifi: ath12k: Add single wiphy support | expand

Commit Message

Rameshkumar Sundaram March 12, 2024, 1:55 p.m. UTC
From: Sriram R <quic_srirrama@quicinc.com>

When multiple radios are advertised as a single wiphy which
supports various bands, a default scan request to mac80211
from cfg80211 will split the driver request based on band,
so each request will have channels belonging to the same band.
With this supported by default, the ath12k driver on receiving
this request checks for one of the channels in the request and
selects the corresponding radio(ar) on which the scan is going
to be performed and creates a vdev on that radio.

Note that on scan completion this vdev is not deleted. If a new
scan request is seen on that same vif for a different band the
vdev will be deleted and created on the new radio supporting the
request. The vdev delete logic is refactored to have this done
dynamically.

The reason for not deleting the vdev on scan stop is to avoid
repeated delete-create sequence if the scan is on the same band.
Also, during channel assign, new vdev creation can be optimized
as well.

Also if the scan is requested when the vdev is in started state,
no switching to new radio is allowed and scan on channels only
within same radio is allowed.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 210 +++++++++++++++++++++-----
 1 file changed, 175 insertions(+), 35 deletions(-)

Comments

Jeff Johnson March 12, 2024, 10:35 p.m. UTC | #1
On 3/12/2024 6:55 AM, Rameshkumar Sundaram wrote:
> From: Sriram R <quic_srirrama@quicinc.com>
> 
> When multiple radios are advertised as a single wiphy which
> supports various bands, a default scan request to mac80211
> from cfg80211 will split the driver request based on band,
> so each request will have channels belonging to the same band.
> With this supported by default, the ath12k driver on receiving
> this request checks for one of the channels in the request and
> selects the corresponding radio(ar) on which the scan is going
> to be performed and creates a vdev on that radio.
> 
> Note that on scan completion this vdev is not deleted. If a new
> scan request is seen on that same vif for a different band the
> vdev will be deleted and created on the new radio supporting the
> request. The vdev delete logic is refactored to have this done
> dynamically.
> 
> The reason for not deleting the vdev on scan stop is to avoid
> repeated delete-create sequence if the scan is on the same band.
> Also, during channel assign, new vdev creation can be optimized
> as well.
> 
> Also if the scan is requested when the vdev is in started state,
> no switching to new radio is allowed and scan on channels only
> within same radio is allowed.
> 
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> 
> Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
> ---
...
> +	/* If the vif is already assigned to a specific vdev of an ar,
> +	 * check whether its already started, vdev which is started
> +	 * are not allowed to switch to a new radio.
> +	 * If the vdev is not started, but was earlier created on a
> +	 * different ar, delete that vdev and create a new one. We don't
> +	 * delete at the scan stop as an optimization to avoid reduntant

s/reduntant/redundant/

> +	 * delete-create vdev's for the same ar, in case the request is
> +	 * always on the same band for the vif
> +	 */
Rameshkumar Sundaram March 19, 2024, 3:58 p.m. UTC | #2
On 3/13/2024 4:05 AM, Jeff Johnson wrote:
> On 3/12/2024 6:55 AM, Rameshkumar Sundaram wrote:
>> From: Sriram R <quic_srirrama@quicinc.com>
>>
>> When multiple radios are advertised as a single wiphy which
>> supports various bands, a default scan request to mac80211
>> from cfg80211 will split the driver request based on band,
>> so each request will have channels belonging to the same band.
>> With this supported by default, the ath12k driver on receiving
>> this request checks for one of the channels in the request and
>> selects the corresponding radio(ar) on which the scan is going
>> to be performed and creates a vdev on that radio.
>>
>> Note that on scan completion this vdev is not deleted. If a new
>> scan request is seen on that same vif for a different band the
>> vdev will be deleted and created on the new radio supporting the
>> request. The vdev delete logic is refactored to have this done
>> dynamically.
>>
>> The reason for not deleting the vdev on scan stop is to avoid
>> repeated delete-create sequence if the scan is on the same band.
>> Also, during channel assign, new vdev creation can be optimized
>> as well.
>>
>> Also if the scan is requested when the vdev is in started state,
>> no switching to new radio is allowed and scan on channels only
>> within same radio is allowed.
>>
>> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
>> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
>>
>> Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
>> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
>> ---
> ...
>> +	/* If the vif is already assigned to a specific vdev of an ar,
>> +	 * check whether its already started, vdev which is started
>> +	 * are not allowed to switch to a new radio.
>> +	 * If the vdev is not started, but was earlier created on a
>> +	 * different ar, delete that vdev and create a new one. We don't
>> +	 * delete at the scan stop as an optimization to avoid reduntant
> 
> s/reduntant/redundant/
Sure will fix it in next version
> 
>> +	 * delete-create vdev's for the same ar, in case the request is
>> +	 * always on the same band for the vif
>> +	 */
>
diff mbox series

Patch

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index b6afef81a2d8..3ce1407e0e5f 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -244,6 +244,8 @@  static const u32 ath12k_smps_map[] = {
 static int ath12k_start_vdev_delay(struct ath12k *ar,
 				   struct ath12k_vif *arvif);
 static void ath12k_mac_stop(struct ath12k *ar);
+static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif);
+static int ath12k_mac_vdev_delete(struct ath12k *ar, struct ieee80211_vif *vif);
 
 static const char *ath12k_mac_phymode_str(enum wmi_phy_mode mode)
 {
@@ -3009,6 +3011,42 @@  static void ath12k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 	mutex_unlock(&ar->conf_mutex);
 }
 
+static struct ath12k*
+ath12k_mac_select_scan_device(struct ieee80211_hw *hw,
+			      struct ieee80211_vif *vif,
+			      struct ieee80211_scan_request *req)
+{
+	struct ath12k_hw *ah = hw->priv;
+	enum nl80211_band band;
+	struct ath12k *ar;
+	int i;
+
+	if (ah->num_radio == 1)
+		return ah->radio;
+
+	/* Currently mac80211 supports splitting scan requests into
+	 * multiple scan requests per band.
+	 * Loop through first channel and determine the scan radio
+	 * TODO: There could be 5 GHz low/high channels in that case
+	 * split the hw request and perform multiple scans
+	 */
+
+	if (req->req.channels[0]->center_freq < ATH12K_MIN_5G_FREQ)
+		band = NL80211_BAND_2GHZ;
+	else if (req->req.channels[0]->center_freq < ATH12K_MIN_6G_FREQ)
+		band = NL80211_BAND_5GHZ;
+	else
+		band = NL80211_BAND_6GHZ;
+
+	for_each_ar(i, ah, ar) {
+		/* TODO 5 GHz low high split changes */
+		if (ar->mac.sbands[band].channels)
+			return ar;
+	}
+
+	return NULL;
+}
+
 void __ath12k_mac_scan_finish(struct ath12k *ar)
 {
 	struct ieee80211_hw *hw = ath12k_ar_to_hw(ar);
@@ -3178,15 +3216,68 @@  static int ath12k_mac_op_hw_scan(struct ieee80211_hw *hw,
 				 struct ieee80211_scan_request *hw_req)
 {
 	struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
-	struct ath12k *ar;
+	struct ath12k *ar, *prev_ar;
 	struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
 	struct cfg80211_scan_request *req = &hw_req->req;
 	struct ath12k_wmi_scan_req_arg arg = {};
 	int ret;
 	int i;
+	bool create = true;
 
-	ar = ath12k_ah_to_ar(ah, 0);
+	if (ah->num_radio == 1) {
+		WARN_ON(!arvif->is_created);
+		ar = ath12k_ah_to_ar(ah, 0);
+		goto scan;
+	}
+
+	/* Since the targeted scan device could depend on the frequency
+	 * requested in the hw_req, select the corresponding radio
+	 */
+	ar = ath12k_mac_select_scan_device(hw, vif, hw_req);
+	if (!ar)
+		return -EINVAL;
+
+	/* If the vif is already assigned to a specific vdev of an ar,
+	 * check whether its already started, vdev which is started
+	 * are not allowed to switch to a new radio.
+	 * If the vdev is not started, but was earlier created on a
+	 * different ar, delete that vdev and create a new one. We don't
+	 * delete at the scan stop as an optimization to avoid reduntant
+	 * delete-create vdev's for the same ar, in case the request is
+	 * always on the same band for the vif
+	 */
+	if (arvif->is_created) {
+		if (WARN_ON(!arvif->ar))
+			return -EINVAL;
+
+		if (ar != arvif->ar && arvif->is_started)
+			return -EINVAL;
 
+		if (ar != arvif->ar) {
+			/* backup the previously used ar ptr, since the vdev delete
+			 * would assign the arvif->ar to NULL after the call
+			 */
+			prev_ar = arvif->ar;
+			mutex_lock(&prev_ar->conf_mutex);
+			ret = ath12k_mac_vdev_delete(prev_ar, vif);
+			mutex_unlock(&prev_ar->conf_mutex);
+			if (ret)
+				ath12k_warn(prev_ar->ab,
+					    "unable to delete scan vdev %d\n", ret);
+		} else {
+			create = false;
+		}
+	}
+	if (create) {
+		mutex_lock(&ar->conf_mutex);
+		ret = ath12k_mac_vdev_create(ar, vif);
+		mutex_unlock(&ar->conf_mutex);
+		if (ret) {
+			ath12k_warn(ar->ab, "unable to create scan vdev %d\n", ret);
+			return -EINVAL;
+		}
+	}
+scan:
 	mutex_lock(&ar->conf_mutex);
 
 	spin_lock_bh(&ar->data_lock);
@@ -3272,10 +3363,13 @@  static int ath12k_mac_op_hw_scan(struct ieee80211_hw *hw,
 static void ath12k_mac_op_cancel_hw_scan(struct ieee80211_hw *hw,
 					 struct ieee80211_vif *vif)
 {
-	struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
+	struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
 	struct ath12k *ar;
 
-	ar = ath12k_ah_to_ar(ah, 0);
+	if (!arvif->is_created)
+		return;
+
+	ar = arvif->ar;
 
 	mutex_lock(&ar->conf_mutex);
 	ath12k_scan_abort(ar);
@@ -5951,6 +6045,7 @@  static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
 	if (vif->type != NL80211_IFTYPE_MONITOR && ar->monitor_conf_enabled)
 		ath12k_mac_monitor_vdev_create(ar);
 
+	arvif->ar = ar;
 	return ret;
 
 err_peer_del:
@@ -5977,6 +6072,7 @@  static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
 	ath12k_wmi_vdev_delete(ar, arvif->vdev_id);
 	ar->num_created_vdevs--;
 	arvif->is_created = false;
+	arvif->ar = NULL;
 	ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
 	ab->free_vdev_map |= 1LL << arvif->vdev_id;
 	ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
@@ -5995,13 +6091,45 @@  static struct ath12k *ath12k_mac_assign_vif_to_vdev(struct ieee80211_hw *hw,
 {
 	struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
 	struct ath12k_hw *ah = hw->priv;
+	struct ath12k *ar, *prev_ar;
 	struct ath12k_base *ab;
-	struct ath12k *ar;
 	int ret;
 	u8 bit;
 
 	if (arvif->ar) {
-		WARN_ON(!arvif->is_created);
+		/* This is not expected really */
+		if (WARN_ON(!arvif->is_created)) {
+			arvif->ar = NULL;
+			return NULL;
+		}
+
+		if (ah->num_radio == 1)
+			goto out;
+
+		ar = ath12k_get_ar_by_ctx(hw, ctx);
+		/* This can happen as scan vdev gets created during multiple scans
+		 * across different radios before a vdev is brought up in
+		 * a certain radio
+		 */
+		if (ar != arvif->ar) {
+			if (WARN_ON(arvif->is_started))
+				return NULL;
+
+			/* backup the previously used ar ptr since arvif->ar would
+			 * be set to NULL after vdev delete is done
+			 */
+			prev_ar = arvif->ar;
+			mutex_lock(&prev_ar->conf_mutex);
+			ret = ath12k_mac_vdev_delete(prev_ar, vif);
+
+			if (ret)
+				ath12k_warn(prev_ar->ab, "unable to delete vdev %d\n", ret);
+			mutex_unlock(&prev_ar->conf_mutex);
+			ret = ath12k_mac_vdev_create(ar, vif);
+			if (ret)
+				ath12k_warn(ar->ab, "unable to create vdev %d\n", ret);
+			mutex_unlock(&ar->conf_mutex);
+		}
 		goto out;
 	}
 
@@ -6110,38 +6238,19 @@  static void ath12k_mac_vif_unref(struct ath12k_dp *dp, struct ieee80211_vif *vif
 	}
 }
 
-static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
-					   struct ieee80211_vif *vif)
+static int ath12k_mac_vdev_delete(struct ath12k *ar, struct ieee80211_vif *vif)
 {
-	struct ath12k *ar;
 	struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
-	struct ath12k_base *ab;
+	struct ath12k_base *ab = ar->ab;
 	unsigned long time_left;
 	int ret;
 
-	if (!arvif->is_created)
-		return;
-
-	ar = arvif->ar;
-	ab = ar->ab;
-
-	mutex_lock(&ar->conf_mutex);
-
-	ath12k_dbg(ab, ATH12K_DBG_MAC, "mac remove interface (vdev %d)\n",
-		   arvif->vdev_id);
-
-	if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
-		ret = ath12k_peer_delete(ar, arvif->vdev_id, vif->addr);
-		if (ret)
-			ath12k_warn(ab, "failed to submit AP self-peer removal on vdev %d: %d\n",
-				    arvif->vdev_id, ret);
-	}
-
+	lockdep_assert_held(&ar->conf_mutex);
 	reinit_completion(&ar->vdev_delete_done);
 
 	ret = ath12k_wmi_vdev_delete(ar, arvif->vdev_id);
 	if (ret) {
-		ath12k_warn(ab, "failed to delete WMI vdev %d: %d\n",
+		ath12k_warn(ab, "failed to delete WMI scan vdev %d: %d\n",
 			    arvif->vdev_id, ret);
 		goto err_vdev_del;
 	}
@@ -6153,6 +6262,10 @@  static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
 		goto err_vdev_del;
 	}
 
+	ab->free_vdev_map |= 1LL << arvif->vdev_id;
+	ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
+	ar->num_created_vdevs--;
+
 	if (arvif->vdev_type == WMI_VDEV_TYPE_MONITOR) {
 		ar->monitor_vdev_id = -1;
 		ar->monitor_vdev_created = false;
@@ -6160,12 +6273,6 @@  static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
 		ret = ath12k_mac_monitor_vdev_delete(ar);
 	}
 
-	ab->free_vdev_map |= 1LL << (arvif->vdev_id);
-	ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
-	ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
-	ar->num_created_vdevs--;
-	arvif->is_created = false;
-
 	ath12k_dbg(ab, ATH12K_DBG_MAC, "vdev %pM deleted, vdev_id %d\n",
 		   vif->addr, arvif->vdev_id);
 
@@ -6187,6 +6294,39 @@  static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
 	clear_bit(ATH12K_FLAG_MONITOR_ENABLED, &ar->monitor_flags);
 
 	/* TODO: recal traffic pause state based on the available vdevs */
+	arvif->is_created = false;
+	arvif->ar = NULL;
+
+	return ret;
+}
+
+static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
+					   struct ieee80211_vif *vif)
+{
+	struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+	struct ath12k_base *ab;
+	struct ath12k *ar;
+	int ret;
+
+	if (!arvif->is_created)
+		return;
+
+	ar = arvif->ar;
+	ab = ar->ab;
+
+	mutex_lock(&ar->conf_mutex);
+
+	ath12k_dbg(ab, ATH12K_DBG_MAC, "mac remove interface (vdev %d)\n",
+		   arvif->vdev_id);
+
+	if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
+		ret = ath12k_peer_delete(ar, arvif->vdev_id, vif->addr);
+		if (ret)
+			ath12k_warn(ab, "failed to submit AP self-peer removal on vdev %d: %d\n",
+				    arvif->vdev_id, ret);
+	}
+
+	ath12k_mac_vdev_delete(ar, vif);
 
 	mutex_unlock(&ar->conf_mutex);
 }