| Message ID | 1E6ABDEA91ADAB1A+20241218090833.140045-1-wangyuli@uniontech.com (mailing list archive) |
|---|---|
| State | New |
| Delegated to: | Felix Fietkau |
| Headers | show |
| Series | [RESEND.] mt76: mt76u_vendor_request: Do not print error messages when -EPROTO | expand |
From: Wangyuli <wangyuli@uniontech.com> Date: Wed, 18 Dec 2024 17:08:33 +0800 > [RESEND. PATCH] mt76: mt76u_vendor_request: Do not print error messages when -EPROTO Is it a fix or an improvement? You need to specify the target tree, either 'PATCH net' (fixes) or 'PATCH net-next' (improvements). The '.' after 'RESEND' is not needed. > When initializing the network card, unplugging the device will > trigger an -EPROTO error, resulting in a flood of error messages > being printed frantically. > If it's a fix, you need to have a 'Fixes:' tag here. > Co-developed-by: Xu Rao <raoxu@uniontech.com> > Signed-off-by: Xu Rao <raoxu@uniontech.com> > Signed-off-by: WangYuli <wangyuli@uniontech.com> > --- > drivers/net/wireless/mediatek/mt76/usb.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/wireless/mediatek/mt76/usb.c b/drivers/net/wireless/mediatek/mt76/usb.c > index 58ff06823389..f9e67b8c3b3c 100644 > --- a/drivers/net/wireless/mediatek/mt76/usb.c > +++ b/drivers/net/wireless/mediatek/mt76/usb.c > @@ -33,9 +33,9 @@ int __mt76u_vendor_request(struct mt76_dev *dev, u8 req, u8 req_type, > > ret = usb_control_msg(udev, pipe, req, req_type, val, > offset, buf, len, MT_VEND_REQ_TOUT_MS); > - if (ret == -ENODEV) > + if (ret == -ENODEV || ret == -EPROTO) > set_bit(MT76_REMOVED, &dev->phy.state); > - if (ret >= 0 || ret == -ENODEV) > + if (ret >= 0 || ret == -ENODEV || ret == -EPROTO) > return ret; > usleep_range(5000, 10000); How do other drivers handle this? Can -EPROTO happen in other cases, not only unplugging, which this patch would break? Thanks, Olek
Alexander Lobakin <aleksander.lobakin@intel.com> writes: > From: Wangyuli <wangyuli@uniontech.com> > Date: Wed, 18 Dec 2024 17:08:33 +0800 > >> [RESEND. PATCH] mt76: mt76u_vendor_request: Do not print error messages when -EPROTO > > Is it a fix or an improvement? > You need to specify the target tree, either 'PATCH net' (fixes) or > 'PATCH net-next' (improvements). Actually this is a wireless driver so the options are either wireless tree or Felix' tree (for -next). And please add 'wifi:' to subject.
On 2024/12/19 00:10, Alexander Lobakin wrote: > Is it a fix or an improvement? > You need to specify the target tree, either 'PATCH net' (fixes) or > 'PATCH net-next' (improvements). It is a fix not an improvement. > How do other drivers handle this? > Can -EPROTO happen in other cases, not only unplugging, which this patch > would break? > When initializing the network card, unplugging the device will trigger an -EPROTO error. The exception is printed as follows： mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71 mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71 ... It will continue to print more than 2000 times for about 5 minutes, causing the usb device to be unable to be disconnected. During this period, the usb port cannot recognize the new device because the old device has not disconnected. There may be other operating methods that cause -EPROTO, but -EPROTO is a low-level hardware error. It is unwise to repeat vendor requests expecting to read correct data. It is a better choice to treat -EPROTO and -ENODEV the same way。 Similar to commit （mt76: usb: process URBs with status EPROTO properly）do no schedule rx_worker for urb marked with status set -EPROTO. I also reproduced this situation when plugging and unplugging the device, and this patch is effective. Just do not vendor request again for urb marked with status set -EPROTO . Thanks,
From: Wangyuli <wangyuli@uniontech.com> Date: Thu, 19 Dec 2024 15:11:24 +0800 > On 2024/12/19 00:10, Alexander Lobakin wrote: > >> Is it a fix or an improvement? >> You need to specify the target tree, either 'PATCH net' (fixes) or >> 'PATCH net-next' (improvements). > It is a fix not an improvement. So you need to add the correct tree and/or subject prefix and specify "Fixes:" tag with the commit this change fixes. >> How do other drivers handle this? >> Can -EPROTO happen in other cases, not only unplugging, which this patch >> would break? >> > When initializing the network card, unplugging the device will trigger > an -EPROTO error. > > The exception is printed as follows： > > > mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71 > mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71 > ... > > > It will continue to print more than 2000 times for about 5 minutes, > causing the usb device to be unable to be disconnected. During this > period, the usb port cannot recognize the new device because the old > device has not disconnected. > > There may be other operating methods that cause -EPROTO, but -EPROTO is > a low-level hardware error. It is unwise to repeat vendor requests > expecting to read correct data. It is a better choice to treat -EPROTO > and -ENODEV the same way. > > Similar to commit （mt76: usb: process URBs with status EPROTO > properly）do no schedule rx_worker for urb marked with status set - > EPROTO. I also reproduced this situation when plugging and unplugging > the device, and this patch is effective. I'm not a wireless expert, from my PoV sounds good. Just describe everything in details in the commit message, so that it will be clear for everyone. > > Just do not vendor request again for urb marked with status set -EPROTO . > > > Thanks, > > -- > WangYuli Thanks, Olek
diff --git a/drivers/net/wireless/mediatek/mt76/usb.c b/drivers/net/wireless/mediatek/mt76/usb.c index 58ff06823389..f9e67b8c3b3c 100644 --- a/drivers/net/wireless/mediatek/mt76/usb.c +++ b/drivers/net/wireless/mediatek/mt76/usb.c @@ -33,9 +33,9 @@ int __mt76u_vendor_request(struct mt76_dev *dev, u8 req, u8 req_type, ret = usb_control_msg(udev, pipe, req, req_type, val, offset, buf, len, MT_VEND_REQ_TOUT_MS); - if (ret == -ENODEV) + if (ret == -ENODEV || ret == -EPROTO) set_bit(MT76_REMOVED, &dev->phy.state); - if (ret >= 0 || ret == -ENODEV) + if (ret >= 0 || ret == -ENODEV || ret == -EPROTO) return ret; usleep_range(5000, 10000); }