Message ID | 20121029195127.GA32749@harvey-pc.matrox.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Mon, 2012-10-29 at 15:51 -0400, Christopher Harvey wrote: > In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN > instead of 0x00NN on the bus. The 0xFFs were actually uninitialized > bits that were left unset in the GPMC command output register. The > reason they weren't initialized in 16bit mode is that if the same code > that writes to this register was used in 8bit mode then 2 commands > would be output in 8bit mode. One for the low byte, and an extra 0x0 > command for the high byte. This commit uses writew if we're using > 16bit NAND. This commit also changes the high byte in the command > output register, but they are ignored by NAND chips anyway. > > Most chips seem fine with the extra 0xFFs, but the ONFI spec says > otherwise. > > Signed-off-by: Christopher Harvey <charvey@matrox.com> Pushed to l2-mtd.git, thanks!
On Thu, Nov 15, 2012 at 01:02:09PM +0200, Artem Bityutskiy wrote: > On Mon, 2012-10-29 at 15:51 -0400, Christopher Harvey wrote: > > In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN > > instead of 0x00NN on the bus. The 0xFFs were actually uninitialized > > bits that were left unset in the GPMC command output register. The > > reason they weren't initialized in 16bit mode is that if the same code > > that writes to this register was used in 8bit mode then 2 commands > > would be output in 8bit mode. One for the low byte, and an extra 0x0 > > command for the high byte. This commit uses writew if we're using > > 16bit NAND. This commit also changes the high byte in the command > > output register, but they are ignored by NAND chips anyway. > > > > Most chips seem fine with the extra 0xFFs, but the ONFI spec says > > otherwise. > > > > Signed-off-by: Christopher Harvey <charvey@matrox.com> > > Pushed to l2-mtd.git, thanks! !!! Did anybody get around to testing this? I thought this patch had been abandoned. Will testing get done on an omap chip now that it is in a tree? I should have prefixed it with RFC. -C
On Thu, 2012-11-15 at 09:48 -0500, Christopher Harvey wrote: > On Thu, Nov 15, 2012 at 01:02:09PM +0200, Artem Bityutskiy wrote: > > On Mon, 2012-10-29 at 15:51 -0400, Christopher Harvey wrote: > > > In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN > > > instead of 0x00NN on the bus. The 0xFFs were actually uninitialized > > > bits that were left unset in the GPMC command output register. The > > > reason they weren't initialized in 16bit mode is that if the same code > > > that writes to this register was used in 8bit mode then 2 commands > > > would be output in 8bit mode. One for the low byte, and an extra 0x0 > > > command for the high byte. This commit uses writew if we're using > > > 16bit NAND. This commit also changes the high byte in the command > > > output register, but they are ignored by NAND chips anyway. > > > > > > Most chips seem fine with the extra 0xFFs, but the ONFI spec says > > > otherwise. > > > > > > Signed-off-by: Christopher Harvey <charvey@matrox.com> > > > > Pushed to l2-mtd.git, thanks! > > !!! Did anybody get around to testing this? I thought this patch had > been abandoned. Will testing get done on an omap chip now that it > is in a tree? > > I should have prefixed it with RFC. I assume _you_ tested it, and Ivan was happy. But if it is untested, I am dropping it.
On Thu, Nov 15, 2012 at 05:18:44PM +0200, Artem Bityutskiy wrote: > On Thu, 2012-11-15 at 09:48 -0500, Christopher Harvey wrote: > > On Thu, Nov 15, 2012 at 01:02:09PM +0200, Artem Bityutskiy wrote: > > > On Mon, 2012-10-29 at 15:51 -0400, Christopher Harvey wrote: > > > > In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN > > > > instead of 0x00NN on the bus. The 0xFFs were actually uninitialized > > > > bits that were left unset in the GPMC command output register. The > > > > reason they weren't initialized in 16bit mode is that if the same code > > > > that writes to this register was used in 8bit mode then 2 commands > > > > would be output in 8bit mode. One for the low byte, and an extra 0x0 > > > > command for the high byte. This commit uses writew if we're using > > > > 16bit NAND. This commit also changes the high byte in the command > > > > output register, but they are ignored by NAND chips anyway. > > > > > > > > Most chips seem fine with the extra 0xFFs, but the ONFI spec says > > > > otherwise. > > > > > > > > Signed-off-by: Christopher Harvey <charvey@matrox.com> > > > > > > Pushed to l2-mtd.git, thanks! > > > > !!! Did anybody get around to testing this? I thought this patch had > > been abandoned. Will testing get done on an omap chip now that it > > is in a tree? > > > > I should have prefixed it with RFC. > > I assume _you_ tested it, and Ivan was happy. But if it is untested, I > am dropping it. > I'm running a slight variation of it on another version of the kernel. I'm glad you're dropping it though...I have a reputation to maintain as well as a kernel. ;) -C -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Nov 15, 2012 at 03:18:44PM +0000, Artem Bityutskiy wrote: > On Thu, 2012-11-15 at 09:48 -0500, Christopher Harvey wrote: > > On Thu, Nov 15, 2012 at 01:02:09PM +0200, Artem Bityutskiy wrote: > > > On Mon, 2012-10-29 at 15:51 -0400, Christopher Harvey wrote: > > > > In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN > > > > instead of 0x00NN on the bus. The 0xFFs were actually uninitialized > > > > bits that were left unset in the GPMC command output register. The > > > > reason they weren't initialized in 16bit mode is that if the same code > > > > that writes to this register was used in 8bit mode then 2 commands > > > > would be output in 8bit mode. One for the low byte, and an extra 0x0 > > > > command for the high byte. This commit uses writew if we're using > > > > 16bit NAND. This commit also changes the high byte in the command > > > > output register, but they are ignored by NAND chips anyway. > > > > > > > > Most chips seem fine with the extra 0xFFs, but the ONFI spec says > > > > otherwise. > > > > > > > > Signed-off-by: Christopher Harvey <charvey@matrox.com> > > > > > > Pushed to l2-mtd.git, thanks! > > > > !!! Did anybody get around to testing this? I thought this patch had > > been abandoned. Will testing get done on an omap chip now that it > > is in a tree? > > > > I should have prefixed it with RFC. > > I assume _you_ tested it, and Ivan was happy. But if it is untested, I > am dropping it. Unfortunately I can't test it at the moment, BR, -- Ivan -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 5b31386..ae6738f 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -225,16 +225,20 @@ static void omap_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); + void __iomem *reg; if (cmd != NAND_CMD_NONE) { if (ctrl & NAND_CLE) - writeb(cmd, info->reg.gpmc_nand_command); - + reg = info->reg.gpmc_nand_command; else if (ctrl & NAND_ALE) - writeb(cmd, info->reg.gpmc_nand_address); - + reg = info->reg.gpmc_nand_address; else /* NAND_NCE */ - writeb(cmd, info->reg.gpmc_nand_data); + reg = info->reg.gpmc_nand_data; + + if (info->nand.options & NAND_BUSWIDTH_16) + writew(cmd, reg); + else + writeb(cmd, reg); } }
In 16bit NAND mode the GPMC would send the address 0xNN as 0xFFNN instead of 0x00NN on the bus. The 0xFFs were actually uninitialized bits that were left unset in the GPMC command output register. The reason they weren't initialized in 16bit mode is that if the same code that writes to this register was used in 8bit mode then 2 commands would be output in 8bit mode. One for the low byte, and an extra 0x0 command for the high byte. This commit uses writew if we're using 16bit NAND. This commit also changes the high byte in the command output register, but they are ignored by NAND chips anyway. Most chips seem fine with the extra 0xFFs, but the ONFI spec says otherwise. Signed-off-by: Christopher Harvey <charvey@matrox.com> --- drivers/mtd/nand/omap2.c | 14 +++++++++----- 1 files changed, 9 insertions(+), 5 deletions(-)