diff mbox

[RFC:,v5] i2c: exynos5: add High Speed I2C controller driver

Message ID 1363796690-30242-1-git-send-email-ch.naveen@samsung.com (mailing list archive)
State New, archived
Headers show

Commit Message

Naveen Krishna Chatradhi March 20, 2013, 4:24 p.m. UTC
Adds support for High Speed I2C driver found in Exynos5 and later
SoCs from Samsung. This driver currently supports Auto mode.

Driver only supports Device Tree method.
Note: Added debugfs support for registers view, not tested.

Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
---
Changes since v4:
1. Fixed ISR routine to handle interrupt and fifo status registers
2. Handle the error return
3. Split the exynos5_i2c_set_timing to report error
4. Added description for the static functions and modes of operation
5. implemented TX fifo and RX fifo usage

 .../devicetree/bindings/i2c/i2c-exynos5.txt        |   50 ++
 drivers/i2c/busses/Kconfig                         |    7 +
 drivers/i2c/busses/Makefile                        |    1 +
 drivers/i2c/busses/i2c-exynos5.c                   |  871 ++++++++++++++++++++
 4 files changed, 929 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
 create mode 100644 drivers/i2c/busses/i2c-exynos5.c

Comments

Yuvaraj CD March 25, 2013, 11:52 a.m. UTC | #1
On Wed, Mar 20, 2013 at 9:54 PM, Naveen Krishna Chatradhi
<ch.naveen@samsung.com> wrote:
> Adds support for High Speed I2C driver found in Exynos5 and later
> SoCs from Samsung. This driver currently supports Auto mode.
>
> Driver only supports Device Tree method.
> Note: Added debugfs support for registers view, not tested.
>
> Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
> Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
> ---
> Changes since v4:
> 1. Fixed ISR routine to handle interrupt and fifo status registers
> 2. Handle the error return
> 3. Split the exynos5_i2c_set_timing to report error
> 4. Added description for the static functions and modes of operation
> 5. implemented TX fifo and RX fifo usage
>
>  .../devicetree/bindings/i2c/i2c-exynos5.txt        |   50 ++
>  drivers/i2c/busses/Kconfig                         |    7 +
>  drivers/i2c/busses/Makefile                        |    1 +
>  drivers/i2c/busses/i2c-exynos5.c                   |  871 ++++++++++++++++++++
>  4 files changed, 929 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
>  create mode 100644 drivers/i2c/busses/i2c-exynos5.c
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
> new file mode 100644
> index 0000000..0bc9347
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
> @@ -0,0 +1,50 @@
> +* Samsung's High Speed I2C controller
> +
> +The Samsung's High Speed I2C controller is used to interface with I2C devices
> +at various speeds ranging from 100khz to 3.4Mhz.
> +
> +Required properties:
> +  - compatible: value should be.
> +      (a) "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c.
> +  - reg: physical base address of the controller and length of memory mapped
> +    region.
> +  - interrupts: interrupt number to the cpu.
> +
> +  - Samsung GPIO variant (deprecated):
> +    - gpios: The order of the gpios should be the following: <SDA, SCL>.
> +      The gpio specifier depends on the gpio controller.
> +  - Pinctrl variant (preferred, if available):
> +    - pinctrl-0: Pin control group to be used for this controller.
> +    - pinctrl-names: Should contain only one value - "default".
> +
> +Optional properties:
> +  - samsung,hs-mode: Mode of operation, High speed or Fast speed mode. If not
> +    specified, default value is 0.
> +  - samsung,hs-clock-freq: Desired operating frequency in Hz of the bus.
> +    If not specified, the default value in Hz is 100000.
> +  - samsung,fs-clock-freq: Desired operarting frequency in Hz of the bus.
> +    If not specified, the default value in Hz is 100000.
> +
> +Example:
> +
> +       hsi2c@12ca0000 {
> +               compatible = "samsung,exynos5-hsi2c";
> +               reg = <0x12ca0000 0x100>;
> +               interrupts = <56>;
> +               samsung,fs-clock-freq = <100000>;
> +               /* Samsung GPIO variant begins here */
> +               gpios = <&gpd1 2 0 /* SDA */
> +                        &gpd1 3 0 /* SCL */>;
> +               /* Samsung GPIO variant ends here */
> +               /* Pinctrl variant begins here */
> +               pinctrl-0 = <&i2c4_bus>;
> +               pinctrl-names = "default";
> +               /* Pinctrl variant ends here */
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               s2mps11_pmic@66 {
> +                       compatible = "samsung,s2mps11-pmic";
> +                       reg = <0x66>;
> +               };
> +       };
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index a3725de..78b4936 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -434,6 +434,13 @@ config I2C_EG20T
>           ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
>           ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
>
> +config I2C_EXYNOS5
> +       tristate "Exynos5 high-speed I2C driver"
> +       depends on ARCH_EXYNOS5 && OF
> +       help
> +         Say Y here to include support for High-speed I2C controller in the
> +         Exynos5 based Samsung SoCs.
> +
>  config I2C_GPIO
>         tristate "GPIO-based bitbanging I2C"
>         depends on GENERIC_GPIO
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index 8f4fc23..b19366c 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -42,6 +42,7 @@ i2c-designware-platform-objs := i2c-designware-platdrv.o
>  obj-$(CONFIG_I2C_DESIGNWARE_PCI)       += i2c-designware-pci.o
>  i2c-designware-pci-objs := i2c-designware-pcidrv.o
>  obj-$(CONFIG_I2C_EG20T)                += i2c-eg20t.o
> +obj-$(CONFIG_I2C_EXYNOS5)      += i2c-exynos5.o
>  obj-$(CONFIG_I2C_GPIO)         += i2c-gpio.o
>  obj-$(CONFIG_I2C_HIGHLANDER)   += i2c-highlander.o
>  obj-$(CONFIG_I2C_IBM_IIC)      += i2c-ibm_iic.o
> diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
> new file mode 100644
> index 0000000..e8e6483
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-exynos5.c
> @@ -0,0 +1,871 @@
> +/**
> + * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/debugfs.h>
> +
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/time.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <linux/errno.h>
> +#include <linux/err.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/clk.h>
> +#include <linux/slab.h>
> +#include <linux/io.h>
> +#include <linux/of_address.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_i2c.h>
> +
> +/*
> + * HSI2C controller from Samsung supports 2 modes of operation
> + * 1. Auto mode: Where in master automatically controls the whole transaction
> + * 2. Manual mode: Software controls the transaction by issuing commands
> + *    START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register.
> + *
> + * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register
> + *
> + * Special bits are available for both modes of operation to set commands
> + * and for checking transfer status
> + */
> +
> +/* Register Map */
> +#define HSI2C_CTL              0x00
> +#define HSI2C_FIFO_CTL         0x04
> +#define HSI2C_TRAILIG_CTL      0x08
> +#define HSI2C_CLK_CTL          0x0C
> +#define HSI2C_CLK_SLOT         0x10
> +#define HSI2C_INT_ENABLE       0x20
> +#define HSI2C_INT_STATUS       0x24
> +#define HSI2C_ERR_STATUS       0x2C
> +#define HSI2C_FIFO_STATUS      0x30
> +#define HSI2C_TX_DATA          0x34
> +#define HSI2C_RX_DATA          0x38
> +#define HSI2C_CONF             0x40
> +#define HSI2C_AUTO_CONF                0x44
> +#define HSI2C_TIMEOUT          0x48
> +#define HSI2C_MANUAL_CMD       0x4C
> +#define HSI2C_TRANS_STATUS     0x50
> +#define HSI2C_TIMING_HS1       0x54
> +#define HSI2C_TIMING_HS2       0x58
> +#define HSI2C_TIMING_HS3       0x5C
> +#define HSI2C_TIMING_FS1       0x60
> +#define HSI2C_TIMING_FS2       0x64
> +#define HSI2C_TIMING_FS3       0x68
> +#define HSI2C_TIMING_SLA       0x6C
> +#define HSI2C_ADDR             0x70
> +
> +/* I2C_CTL Register bits */
> +#define HSI2C_FUNC_MODE_I2C                    (1u << 0)
> +#define HSI2C_MASTER                           (1u << 3)
> +#define HSI2C_RXCHON                           (1u << 6)
> +#define HSI2C_TXCHON                           (1u << 7)
> +#define HSI2C_SW_RST                           (1u << 31)
> +
> +/* I2C_FIFO_CTL Register bits */
> +#define HSI2C_RXFIFO_EN                                (1u << 0)
> +#define HSI2C_TXFIFO_EN                                (1u << 1)
> +#define HSI2C_TXFIFO_TRIGGER_LEVEL             (0x30 << 16)
> +#define HSI2C_RXFIFO_TRIGGER_LEVEL             (0x30 << 4)
> +
> +/* I2C_TRAILING_CTL Register bits */
> +#define HSI2C_TRAILING_COUNT                   (0xf)
> +
> +/* I2C_INT_EN Register bits */
> +#define HSI2C_INT_TX_ALMOSTEMPTY_EN            (1u << 0)
> +#define HSI2C_INT_RX_ALMOSTFULL_EN             (1u << 1)
> +#define HSI2C_INT_TRAILING_EN                  (1u << 6)
> +#define HSI2C_INT_I2C_EN                       (1u << 9)
> +
> +/* I2C_INT_STAT Register bits */
> +#define HSI2C_INT_TX_ALMOSTEMPTY               (1u << 0)
> +#define HSI2C_INT_RX_ALMOSTFULL                        (1u << 1)
> +#define HSI2C_INT_TX_UNDERRUN                  (1u << 2)
> +#define HSI2C_INT_TX_OVERRUN                   (1u << 3)
> +#define HSI2C_INT_RX_UNDERRUN                  (1u << 4)
> +#define HSI2C_INT_RX_OVERRUN                   (1u << 5)
> +#define HSI2C_INT_TRAILING                     (1u << 6)
> +#define HSI2C_INT_I2C                          (1u << 9)
> +#define HSI2C_RX_INT                           (HSI2C_INT_RX_ALMOSTFULL | \
> +                                                HSI2C_INT_RX_UNDERRUN | \
> +                                                HSI2C_INT_RX_OVERRUN | \
> +                                                HSI2C_INT_TRAILING)
> +
> +/* I2C_FIFO_STAT Register bits */
> +#define HSI2C_RX_FIFO_EMPTY                    (1u << 24)
> +#define HSI2C_RX_FIFO_FULL                     (1u << 23)
> +#define HSI2C_RX_FIFO_LVL(x)                   ((x >> 16) & 0x7f)
> +#define HSI2C_TX_FIFO_EMPTY                    (1u << 8)
> +#define HSI2C_TX_FIFO_FULL                     (1u << 7)
> +#define HSI2C_TX_FIFO_LVL(x)                   ((x >> 0) & 0x7f)
> +#define HSI2C_FIFO_EMPTY                       (HSI2C_RX_FIFO_EMPTY |  \
> +                                               HSI2C_TX_FIFO_EMPTY)
> +
> +/* I2C_CONF Register bits */
> +#define HSI2C_AUTO_MODE                                (1u << 31)
> +#define HSI2C_10BIT_ADDR_MODE                  (1u << 30)
> +#define HSI2C_HS_MODE                          (1u << 29)
> +
> +/* I2C_AUTO_CONF Register bits */
> +#define HSI2C_READ_WRITE                       (1u << 16)
> +#define HSI2C_STOP_AFTER_TRANS                 (1u << 17)
> +#define HSI2C_MASTER_RUN                       (1u << 31)
> +
> +/* I2C_TIMEOUT Register bits */
> +#define HSI2C_TIMEOUT_EN                       (1u << 31)
> +
> +/* I2C_TRANS_STATUS register bits */
> +#define HSI2C_MASTER_BUSY                      (1u << 17)
> +#define HSI2C_SLAVE_BUSY                       (1u << 16)
> +#define HSI2C_TIMEOUT_AUTO                     (1u << 4)
> +#define HSI2C_NO_DEV                           (1u << 3)
> +#define HSI2C_NO_DEV_ACK                       (1u << 2)
> +#define HSI2C_TRANS_ABORT                      (1u << 1)
> +#define HSI2C_TRANS_DONE                       (1u << 0)
> +
> +/* I2C_ADDR register bits */
> +#define HSI2C_SLV_ADDR_SLV(x)                  ((x & 0x3ff) << 0)
> +#define HSI2C_SLV_ADDR_MAS(x)                  ((x & 0x3ff) << 10)
> +#define HSI2C_MASTER_ID(x)                     ((x & 0xff) << 24)
> +
> +/* Controller operating frequency, timing values for operation
> + * are calculated against this frequency
> + */
> +#define HSI2C_HS_TX_CLOCK      1000000
> +#define HSI2C_FS_TX_CLOCK      1000000
> +#define HSI2C_HIGH_SPD         1
> +#define HSI2C_FAST_SPD         0
> +
> +#define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000))
> +
> +/* timeout for pm runtime autosuspend */
> +#define EXYNOS5_I2C_PM_TIMEOUT         1000    /* ms */
> +
> +struct exynos5_i2c {
> +       struct i2c_adapter      adap;
> +       unsigned int            suspended:1;
> +
> +       struct i2c_msg          *msg;
> +       struct completion       msg_complete;
> +       unsigned int            msg_ptr;
> +       unsigned int            msg_len;
> +
> +       unsigned int            irq;
> +
> +       void __iomem            *regs;
> +       struct clk              *clk;
> +       struct device           *dev;
> +       int                     state;
> +
> +       /* GPIO lines for SDA/SCL*/
> +       int                     gpios[2];
> +
> +       /* Controller operating frequency */
> +       unsigned int            clock;
> +       unsigned int            clk_cycle;
> +       unsigned int            clk_div;
> +
> +       /* HSI2C Controller can operate in
> +        * 1. High speed upto 3.4Mbps
> +        * 2. Fast speed upto 1Mbps
> +        */
> +       int                     speed_mode;
> +};
> +
> +static const struct of_device_id exynos5_i2c_match[] = {
> +       { .compatible = "samsung,exynos5-hsi2c" },
> +       {},
> +};
> +MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
> +
> +static inline void exynos5_i2c_stop(struct exynos5_i2c *i2c)
> +{
> +       writel(0, i2c->regs + HSI2C_INT_ENABLE);
> +
> +       complete(&i2c->msg_complete);
> +}
> +
> +static void exynos5_i2c_en_timeout(struct exynos5_i2c *i2c)
> +{
> +       u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
> +
> +       /* Clear to enable Timeout */
> +       i2c_timeout &= ~HSI2C_TIMEOUT_EN;
> +       writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
> +}
> +
> +/* exynos5_i2c_clock_info: Calculates the clock divisor and
> + * the clock cycle length (SCLK High + SCLK Low)
> + *
> + * Returns 0 on success,  -EINVAL if the cycle length cannot
> + * be calculated.
> + */
> +static int exynos5_i2c_clock_info(struct exynos5_i2c *i2c)
> +{
> +       unsigned int op_clk = i2c->clock;
> +       unsigned int clkin = clk_get_rate(i2c->clk);
> +       unsigned int i, utemp0 = 0, utemp1 = 0, utemp2 = 0;
> +       unsigned int t_ftl_cycle;
> +
> +       /* FPCLK / FI2C =
> +        * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
> +        * utemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
> +        * utemp1 = (TSCLK_L + TSCLK_H + 2)
> +        * utemp2 = TSCLK_L + TSCLK_H
> +        */
> +       t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
> +       utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
> +
> +       /* CLK_DIV max is 256 */
> +       for (i = 0; i < 256; i++) {
> +               utemp1 = utemp0 / (i + 1);
> +               /* SCLK_L/H max is 256 / 2 */
> +               if (utemp1 < 128) {
I think TSCLK_L and TSCLK_H both can be configured upto 255.Why
limiting it to < 128 ?
By limiting it to < 128 dont we achieve lesser SCL clock?
> +                       utemp2 = utemp1 - 2;
> +                       break;
> +               }
> +       }
> +
> +       if (utemp2 <= 0)
> +               return -EINVAL;
> +
> +       i2c->clk_cycle = utemp2;
> +       i2c->clk_div = i;
> +
> +       return 0;
> +}
> +
> +/* exynos5_i2c_set_timing: updates the registers with appropriate
> + * timing values calculated earlier (exynos5_i2c_clock_info)
> + *
> + * To handle the error case in calculates and to avoid the subsequent
> + * calculates the clk_div and clk_cycle are stored
> + */
> +static void exynos5_i2c_set_timing(struct exynos5_i2c *i2c)
> +{
> +       u32 i2c_timing_s1;
> +       u32 i2c_timing_s2;
> +       u32 i2c_timing_s3;
> +       u32 i2c_timing_sla;
> +       unsigned int n_clkdiv;
> +       unsigned int t_start_su, t_start_hd;
> +       unsigned int t_stop_su;
> +       unsigned int t_data_su, t_data_hd;
> +       unsigned int t_scl_l, t_scl_h;
> +       unsigned int t_sr_release;
> +
> +       n_clkdiv = i2c->clk_div;
> +       t_scl_l = i2c->clk_cycle / 2;
> +       t_scl_h = i2c->clk_cycle / 2;
> +       t_start_su = t_scl_l;
> +       t_start_hd = t_scl_l;
> +       t_stop_su = t_scl_l;
> +       t_data_su = t_scl_l / 2;
> +       t_data_hd = t_scl_l / 2;
> +       t_sr_release = i2c->clk_cycle;
> +
> +       i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
> +       i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
> +       i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
> +       i2c_timing_sla = t_data_hd << 0;
> +
> +       dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
> +               t_start_su, t_start_hd, t_stop_su);
> +       dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
> +               t_data_su, t_scl_l, t_scl_h);
> +       dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
> +               n_clkdiv, t_sr_release);
> +       dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
> +
> +       if (i2c->speed_mode == HSI2C_HIGH_SPD) {
> +               writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
> +               writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
> +               writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
> +       } else {
> +               writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
> +               writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
> +               writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
> +       }
> +       writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
> +}
> +
> +/* exynos5_i2c_init: configures the controller for I2C functionality
> + * Programs I2C controller for Master mode operation
> + *
> + * Note: Currently, supports AUTO mode of operation.
> + */
> +static void exynos5_i2c_init(struct exynos5_i2c *i2c)
> +{
> +       u32 i2c_conf = readl(i2c->regs + HSI2C_CONF);
> +
> +       writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
> +                                       i2c->regs + HSI2C_CTL);
> +       writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL);
> +
> +       exynos5_i2c_set_timing(i2c);
> +
> +       if (i2c->speed_mode == HSI2C_HIGH_SPD)
> +               i2c_conf |= HSI2C_HS_MODE;
> +
> +       writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF);
> +}
> +
> +static void exynos5_i2c_reset(struct exynos5_i2c *i2c)
> +{
> +       u32 i2c_ctl;
> +
> +       /* Set and clear the bit for reset */
> +       i2c_ctl = readl(i2c->regs + HSI2C_CTL);
> +       i2c_ctl |= HSI2C_SW_RST;
> +       writel(i2c_ctl, i2c->regs + HSI2C_CTL);
> +
> +       i2c_ctl = readl(i2c->regs + HSI2C_CTL);
> +       i2c_ctl &= ~HSI2C_SW_RST;
> +       writel(i2c_ctl, i2c->regs + HSI2C_CTL);
> +
> +       /* Initialize the configure registers */
> +       exynos5_i2c_init(i2c);
> +}
> +
> +static void exynos5_i2c_master_run(struct exynos5_i2c *i2c)
> +{
> +       /* Start data transfer in Master mode */
> +       u32 i2c_auto_conf = readl(i2c->regs + HSI2C_AUTO_CONF);
> +       i2c_auto_conf |= HSI2C_MASTER_RUN;
> +       writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
> +}
> +
> +/* exynos5_i2c_irq: top level IRQ servicing routine
> + *
> + * INT_STATUS registers gives the interrupt details. Further,
> + * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed
> + * state of the bus.
> + */
> +static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
> +{
> +       struct exynos5_i2c *i2c = dev_id;
> +       u32 fifo_level, int_status, fifo_status, trans_status;
> +       unsigned char byte;
> +       int len = 0;
> +
> +       i2c->state = -EINVAL;
> +
> +       int_status = readl(i2c->regs + HSI2C_INT_STATUS);
> +       fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
> +
> +       if (int_status & HSI2C_INT_I2C) {
> +               trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
> +               if (trans_status & HSI2C_NO_DEV_ACK) {
> +                       dev_dbg(i2c->dev, "No ACK from device\n");
> +                       i2c->state = -ENXIO;
> +               } else if (trans_status & HSI2C_NO_DEV) {
> +                       dev_dbg(i2c->dev, "No device\n");
> +                       i2c->state = -ENXIO;
> +               } else if (trans_status & HSI2C_TRANS_ABORT) {
> +                       dev_dbg(i2c->dev, "Deal with arbitration lose\n");
> +                       i2c->state = -EAGAIN;
> +               } else if (trans_status & HSI2C_TIMEOUT_AUTO) {
> +                       dev_dbg(i2c->dev, "Accessing device timed out\n");
> +                       i2c->state = -EAGAIN;
> +               }
> +       }
> +       /* TX_ALMOSTEMPTY can happen along with HSI2C_INT_I2C */
> +       else if (int_status &
> +                       (HSI2C_INT_TX_UNDERRUN | HSI2C_INT_TX_ALMOSTEMPTY)) {
> +               fifo_level = HSI2C_TX_FIFO_LVL(fifo_status);
> +
> +               /* To support probing the devices for detection */
> +               if (i2c->msg->len == 0) {
> +                       i2c->state = -ENXIO;
> +                       goto stop;
> +               }
> +
> +               /* 0x30 is the default trigger level for TX FIFO */
> +               len = 48 - fifo_level;
> +
> +               if (len > i2c->msg->len)
> +                       len = i2c->msg->len;
> +
> +               i2c->msg_len += len;
> +               while (len > 0) {
> +                       byte = i2c->msg->buf[i2c->msg_ptr++];
> +                       writel(byte, i2c->regs + HSI2C_TX_DATA);
> +                       len--;
> +               }
> +               i2c->state = 0;
> +               goto stop;
> +       }
> +       /* If TX FIFO is full (give chance to clear) */
> +       else if (int_status & HSI2C_INT_TX_OVERRUN)
> +               i2c->state = 0;
> +
> +       if (int_status & (HSI2C_INT_RX_OVERRUN | HSI2C_INT_TRAILING |
> +               HSI2C_INT_RX_UNDERRUN | HSI2C_INT_RX_ALMOSTFULL)) {
> +               fifo_level = HSI2C_RX_FIFO_LVL(fifo_status);
> +
> +               if (fifo_level >= i2c->msg->len)
> +                       len = i2c->msg->len;
> +               else
> +                       len = fifo_level;
> +
> +               i2c->msg_len += len;
> +               while (len > 0) {
> +                       byte = (unsigned char)
> +                               readl(i2c->regs + HSI2C_RX_DATA);
> +                       i2c->msg->buf[i2c->msg_ptr++] = byte;
> +                       len--;
> +               }
> +               i2c->state = 0;
> +       }
> +
> +
> + stop:
> +       if ((i2c->msg_len == i2c->msg->len) || (i2c->state < 0))
> +               exynos5_i2c_stop(i2c);
> +
> +       /* Set these bits to clear them */
> +       writel(readl(i2c->regs + HSI2C_INT_STATUS),
> +                               i2c->regs + HSI2C_INT_STATUS);
> +
> +       return IRQ_HANDLED;
> +}
> +
> +/*
> + * exynos5_i2c_message_start: Configures the bus and starts the xfer
> + * i2c: struct exynos5_i2c pointer for the current bus
> + * stop: Enables stop after transfer if set. Set for last transfer of
> + *       in the list of messages.
> + *
> + * Configures the bus for read/write function
> + * Sets chip address to talk to, message length to be sent.
> + * Enables appropriate interrupts and sends start xfer command.
> + */
> +static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
> +{
> +       u32 i2c_ctl;
> +       u32 int_en = HSI2C_INT_I2C_EN;
> +       u32 i2c_auto_conf;
> +       u32 fifo_ctl;
> +
> +       exynos5_i2c_en_timeout(i2c);
> +
> +       fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN |
> +               HSI2C_TXFIFO_TRIGGER_LEVEL | HSI2C_RXFIFO_TRIGGER_LEVEL;
> +       writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
> +
> +       i2c_ctl = readl(i2c->regs + HSI2C_CTL);
> +       i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON);
> +
> +       if (i2c->msg->flags & I2C_M_RD) {
> +               i2c_ctl |= HSI2C_RXCHON;
> +
> +               i2c_auto_conf |= HSI2C_READ_WRITE;
> +
> +               int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
> +                       HSI2C_INT_TRAILING_EN);
> +       } else {
> +               i2c_ctl |= HSI2C_TXCHON;
> +
> +               int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
> +       }
> +
> +       if (stop == 1)
> +               i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
> +
> +       writel(HSI2C_SLV_ADDR_MAS(i2c->msg->addr), i2c->regs + HSI2C_ADDR);
> +
> +       writel(i2c_ctl, i2c->regs + HSI2C_CTL);
> +
> +       /* In auto mode the length of xfer cannot be 0 */
> +       if (i2c->msg->len == 0)
> +               i2c_auto_conf |= 0x1;
> +       else
> +               i2c_auto_conf |= i2c->msg->len;
> +
> +       writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
> +
> +       exynos5_i2c_master_run(i2c);
> +
> +       writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
> +}
> +
> +static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c,
> +                             struct i2c_msg *msgs, int stop)
> +{
> +       unsigned long timeout;
> +       int ret;
> +
> +       i2c->msg = msgs;
> +       i2c->msg_ptr = 0;
> +       i2c->msg_len = 0;
> +
> +       exynos5_i2c_message_start(i2c, stop);
> +
> +       ret = wait_for_completion_interruptible_timeout
> +               (&i2c->msg_complete, EXYNOS5_I2C_TIMEOUT);
> +       if (ret >= 0)
> +               timeout = ret;
> +       else
> +               return ret;
> +
> +       ret = i2c->state;
> +
> +       if (timeout == 0) {
> +               exynos5_i2c_reset(i2c);
> +               dev_warn(i2c->dev, "%s timeout\n",
> +                       (msgs->flags & I2C_M_RD) ? "rx" : "tx");
> +               return ret;
> +       }
> +
> +       if (ret == -EAGAIN) {
> +               exynos5_i2c_reset(i2c);
> +               return ret;
> +       }
> +
> +       return ret;
> +}
> +
> +static int exynos5_i2c_xfer(struct i2c_adapter *adap,
> +                       struct i2c_msg *msgs, int num)
> +{
> +       struct exynos5_i2c *i2c = (struct exynos5_i2c *)adap->algo_data;
> +       struct i2c_msg *msgs_ptr = msgs;
> +       int retry, i = 0;
> +       int ret, ret_pm;
> +       int stop = 0;
> +
> +       if (i2c->suspended) {
> +               dev_err(i2c->dev, "HS-I2C is not initialzed.\n");
> +               return -EIO;
> +       }
> +
> +       ret_pm = pm_runtime_get_sync(i2c->dev);
> +       if (IS_ERR_VALUE(ret_pm)) {
> +               ret = -EIO;
> +               goto out;
> +       }
> +
> +       clk_prepare_enable(i2c->clk);
> +
> +       for (retry = 0; retry < adap->retries; retry++) {
> +               for (i = 0; i < num; i++) {
> +                       stop = (i == num - 1);
> +
> +                       ret = exynos5_i2c_xfer_msg(i2c, msgs_ptr, stop);
> +                       msgs_ptr++;
> +
> +                       if (ret == -EAGAIN) {
> +                               msgs_ptr = msgs;
> +                               break;
> +                       } else if (ret < 0) {
> +                               goto out;
> +                       }
> +               }
> +
> +               if ((i == num) && (ret != -EAGAIN))
> +                       break;
> +
> +               dev_dbg(i2c->dev, "retrying transfer (%d)\n", retry);
> +
> +               udelay(100);
> +       }
> +
> + check:
> +       if (i == num) {
> +               /* only one message, return number of bytes transfered */
> +               if (num == 1)
> +                       ret = i2c->msg_len;
> +               else
> +                       ret = num;
> +       } else {
> +               /* Only one message, cannot access the device */
> +               if (i == 1)
> +                       ret = -EREMOTEIO;
> +               else
> +                       ret = i;
> +
> +               dev_warn(i2c->dev, "xfer message failed\n");
> +       }
> +
> + out:
> +       clk_disable_unprepare(i2c->clk);
> +       pm_runtime_mark_last_busy(i2c->dev);
> +       pm_runtime_put_autosuspend(i2c->dev);
> +       return ret;
> +}
> +
> +static u32 exynos5_i2c_func(struct i2c_adapter *adap)
> +{
> +       return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}
> +
> +static const struct i2c_algorithm exynos5_i2c_algorithm = {
> +       .master_xfer            = exynos5_i2c_xfer,
> +       .functionality          = exynos5_i2c_func,
> +};
> +
> +/**
> + * Parse a list of GPIOs from a node property and request each one
> + *
> + * @param i2c          i2c driver data
> + * @return 0 on success, -EINVAL on error, in which case no GPIOs requested
> +*/
> +static int exynos5_i2c_parse_dt_gpio(struct exynos5_i2c *i2c)
> +{
> +       int idx, gpio, ret;
> +
> +       for (idx = 0; idx < 2; idx++) {
> +               gpio = of_get_gpio(i2c->dev->of_node, idx);
> +               if (!gpio_is_valid(gpio)) {
> +                       dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio);
> +                       return -EINVAL;
> +               }
> +               i2c->gpios[idx] = gpio;
> +
> +               ret = devm_gpio_request(i2c->dev, gpio, "i2c-bus");
> +               if (ret) {
> +                       dev_err(i2c->dev, "gpio [%d] request failed\n", gpio);
> +                       return -EINVAL;
> +               }
> +       }
> +       return 0;
> +}
> +
> +#define HSI2C_REG(regname) {.name = #regname, .offset = regname}
> +static struct debugfs_reg32 exynos5_hsi2c_regs[] = {
> +       HSI2C_REG(HSI2C_CTL), HSI2C_REG(HSI2C_FIFO_CTL),
> +       HSI2C_REG(HSI2C_TRAILIG_CTL), HSI2C_REG(HSI2C_CLK_CTL),
> +       HSI2C_REG(HSI2C_CLK_SLOT), HSI2C_REG(HSI2C_INT_ENABLE),
> +       HSI2C_REG(HSI2C_INT_STATUS), HSI2C_REG(HSI2C_ERR_STATUS),
> +       HSI2C_REG(HSI2C_FIFO_STATUS), HSI2C_REG(HSI2C_TX_DATA),
> +       HSI2C_REG(HSI2C_RX_DATA), HSI2C_REG(HSI2C_CONF),
> +       HSI2C_REG(HSI2C_AUTO_CONF), HSI2C_REG(HSI2C_TIMEOUT),
> +       HSI2C_REG(HSI2C_MANUAL_CMD), HSI2C_REG(HSI2C_TRANS_STATUS),
> +       HSI2C_REG(HSI2C_TIMING_HS1), HSI2C_REG(HSI2C_TIMING_HS2),
> +       HSI2C_REG(HSI2C_TIMING_HS3), HSI2C_REG(HSI2C_TIMING_FS1),
> +       HSI2C_REG(HSI2C_TIMING_FS2), HSI2C_REG(HSI2C_TIMING_FS3),
> +       HSI2C_REG(HSI2C_TIMING_SLA), HSI2C_REG(HSI2C_ADDR),
> +};
> +
> +static struct debugfs_regset32 exynos5_hsi2c_regset = {
> +       .regs = exynos5_hsi2c_regs,
> +       .nregs = ARRAY_SIZE(exynos5_hsi2c_regs),
> +};
> +
> +static struct dentry *exynos5_hsi2c_reg_debugfs;
> +
> +static int exynos5_i2c_probe(struct platform_device *pdev)
> +{
> +       struct device_node *np = pdev->dev.of_node;
> +       struct exynos5_i2c *i2c;
> +       int ret;
> +
> +       if (!np) {
> +               dev_err(&pdev->dev, "no device node\n");
> +               return -ENOENT;
> +       }
> +
> +       i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
> +       if (!i2c) {
> +               dev_err(&pdev->dev, "no memory for state\n");
> +               return -ENOMEM;
> +       }
> +
> +       /* Mode of operation High/Fast Speed mode */
> +       if (of_get_property(np, "samsung,hs-mode", NULL)) {
> +               i2c->speed_mode = 1;
> +               if (of_property_read_u32(np, "samsung,hs-clock", &i2c->clock))
> +                       i2c->clock = HSI2C_HS_TX_CLOCK;
> +       } else {
> +               i2c->speed_mode = 0;
> +               if (of_property_read_u32(np, "samsung,fs-clock", &i2c->clock))
> +                       i2c->clock = HSI2C_FS_TX_CLOCK;
> +       }
> +
> +       strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name));
> +       i2c->adap.owner   = THIS_MODULE;
> +       i2c->adap.algo    = &exynos5_i2c_algorithm;
> +       i2c->adap.retries = 2;
> +       i2c->adap.class   = I2C_CLASS_HWMON | I2C_CLASS_SPD;
> +
> +       i2c->dev = &pdev->dev;
> +       i2c->clk = devm_clk_get(&pdev->dev, "hsi2c");
> +       if (IS_ERR(i2c->clk)) {
> +               dev_err(&pdev->dev, "cannot get clock\n");
> +               return -ENOENT;
> +       }
> +
> +       clk_prepare_enable(i2c->clk);
> +
> +       i2c->regs = of_iomap(np, 0);
> +       if (!i2c->regs) {
> +               dev_err(&pdev->dev, "cannot map HS-I2C IO\n");
> +               ret = -EADDRNOTAVAIL;
> +               goto err_clk;
> +       }
> +
> +       i2c->adap.algo_data = i2c;
> +       i2c->adap.dev.parent = &pdev->dev;
> +
> +       /* parse device tree and inititalise the gpio */
> +       if (exynos5_i2c_parse_dt_gpio(i2c))
> +               return -EINVAL;
> +
> +       init_completion(&i2c->msg_complete);
> +
> +       i2c->irq = ret = irq_of_parse_and_map(np, 0);
> +       if (ret <= 0) {
> +               dev_err(&pdev->dev, "cannot find HS-I2C IRQ\n");
> +               goto err_iomap;
> +       }
> +
> +       ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
> +                               0, dev_name(&pdev->dev), i2c);
> +
> +       if (ret != 0) {
> +               dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq);
> +               goto err_iomap;
> +       }
> +
> +       /*
> +        * TODO: Use private lock to avoid race conditions as
> +        * mentioned in pm_runtime.txt
> +        */
> +       pm_runtime_enable(i2c->dev);
> +       pm_runtime_set_autosuspend_delay(i2c->dev, EXYNOS5_I2C_PM_TIMEOUT);
> +       pm_runtime_use_autosuspend(i2c->dev);
> +
> +       ret = pm_runtime_get_sync(i2c->dev);
> +       if (IS_ERR_VALUE(ret))
> +               goto err_iomap;
> +
> +       ret = exynos5_i2c_clock_info(i2c);
> +       if (ret)
> +               goto err_pm;
> +
> +       exynos5_i2c_init(i2c);
> +
> +       i2c->adap.nr = -1;
> +       i2c->adap.dev.of_node = np;
> +
> +       ret = i2c_add_numbered_adapter(&i2c->adap);
> +       if (ret < 0) {
> +               dev_err(&pdev->dev, "failed to add bus to i2c core\n");
> +               goto err_pm;
> +       }
> +
> +       of_i2c_register_devices(&i2c->adap);
> +       platform_set_drvdata(pdev, i2c);
> +
> +       exynos5_hsi2c_reg_debugfs = debugfs_create_regset32("exynos5-hsi2c",
> +                                                 S_IFREG | S_IRUGO,
> +                                                 NULL, &exynos5_hsi2c_regset);
> +       clk_disable_unprepare(i2c->clk);
> +       pm_runtime_mark_last_busy(i2c->dev);
> +       pm_runtime_put_autosuspend(i2c->dev);
> +
> +       return 0;
> +
> + err_pm:
> +       pm_runtime_put(i2c->dev);
> +       pm_runtime_disable(&pdev->dev);
> + err_iomap:
> +       iounmap(i2c->regs);
> + err_clk:
> +       clk_disable_unprepare(i2c->clk);
> +       return ret;
> +}
> +
> +static int exynos5_i2c_remove(struct platform_device *pdev)
> +{
> +       struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> +       int ret;
> +
> +       ret = pm_runtime_get_sync(&pdev->dev);
> +       if (IS_ERR_VALUE(ret))
> +               return ret;
> +
> +       clk_disable_unprepare(i2c->clk);
> +       pm_runtime_put(&pdev->dev);
> +       pm_runtime_disable(&pdev->dev);
> +
> +       i2c_del_adapter(&i2c->adap);
> +
> +       iounmap(i2c->regs);
> +
> +       return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int exynos5_i2c_suspend_noirq(struct device *dev)
> +{
> +       struct platform_device *pdev = to_platform_device(dev);
> +       struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> +
> +       i2c->suspended = 1;
> +
> +       return 0;
> +}
> +
> +static int exynos5_i2c_resume_noirq(struct device *dev)
> +{
> +       struct platform_device *pdev = to_platform_device(dev);
> +       struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
> +
> +       clk_prepare_enable(i2c->clk);
> +       exynos5_i2c_init(i2c);
> +       clk_disable_unprepare(i2c->clk);
> +       i2c->suspended = 0;
> +
> +       return 0;
> +}
> +
> +static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
> +       .suspend_noirq = exynos5_i2c_suspend_noirq,
> +       .resume_noirq   = exynos5_i2c_resume_noirq,
> +};
> +
> +#define EXYNOS5_DEV_PM_OPS (&exynos5_i2c_dev_pm_ops)
> +#else
> +#define EXYNOS5_DEV_PM_OPS NULL
> +#endif
> +
> +static struct platform_driver exynos5_i2c_driver = {
> +       .probe          = exynos5_i2c_probe,
> +       .remove         = exynos5_i2c_remove,
> +       .driver         = {
> +               .owner  = THIS_MODULE,
> +               .name   = "exynos5-hsi2c",
> +               .pm     = EXYNOS5_DEV_PM_OPS,
> +               .of_match_table = of_match_ptr(exynos5_i2c_match),
> +       },
> +};
> +
> +static int __init i2c_adap_exynos5_init(void)
> +{
> +       return platform_driver_register(&exynos5_i2c_driver);
> +}
> +subsys_initcall(i2c_adap_exynos5_init);
> +
> +static void __exit i2c_adap_exynos5_exit(void)
> +{
> +       platform_driver_unregister(&exynos5_i2c_driver);
> +}
> +module_exit(i2c_adap_exynos5_exit);
> +
> +MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
> +MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>");
> +MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>");
> +MODULE_LICENSE("GPL");
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Wolfram Sang March 26, 2013, 9:23 a.m. UTC | #2
> > +       /* CLK_DIV max is 256 */
> > +       for (i = 0; i < 256; i++) {
> > +               utemp1 = utemp0 / (i + 1);
> > +               /* SCLK_L/H max is 256 / 2 */
> > +               if (utemp1 < 128) {
> I think TSCLK_L and TSCLK_H both can be configured upto 255.Why
> limiting it to < 128 ?
> By limiting it to < 128 dont we achieve lesser SCL clock?

Thanks for reviewing but please quote only the relevant part of the
message (like I did). This improves readability a lot.
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
new file mode 100644
index 0000000..0bc9347
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
@@ -0,0 +1,50 @@ 
+* Samsung's High Speed I2C controller
+
+The Samsung's High Speed I2C controller is used to interface with I2C devices
+at various speeds ranging from 100khz to 3.4Mhz.
+
+Required properties:
+  - compatible: value should be.
+      (a) "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+
+  - Samsung GPIO variant (deprecated):
+    - gpios: The order of the gpios should be the following: <SDA, SCL>.
+      The gpio specifier depends on the gpio controller.
+  - Pinctrl variant (preferred, if available):
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - samsung,hs-mode: Mode of operation, High speed or Fast speed mode. If not
+    specified, default value is 0.
+  - samsung,hs-clock-freq: Desired operating frequency in Hz of the bus.
+    If not specified, the default value in Hz is 100000.
+  - samsung,fs-clock-freq: Desired operarting frequency in Hz of the bus.
+    If not specified, the default value in Hz is 100000.
+
+Example:
+
+	hsi2c@12ca0000 {
+		compatible = "samsung,exynos5-hsi2c";
+		reg = <0x12ca0000 0x100>;
+		interrupts = <56>;
+		samsung,fs-clock-freq = <100000>;
+		/* Samsung GPIO variant begins here */
+		gpios = <&gpd1 2 0 /* SDA */
+			 &gpd1 3 0 /* SCL */>;
+		/* Samsung GPIO variant ends here */
+		/* Pinctrl variant begins here */
+		pinctrl-0 = <&i2c4_bus>;
+		pinctrl-names = "default";
+		/* Pinctrl variant ends here */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		s2mps11_pmic@66 {
+			compatible = "samsung,s2mps11-pmic";
+			reg = <0x66>;
+		};
+	};
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index a3725de..78b4936 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -434,6 +434,13 @@  config I2C_EG20T
 	  ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
 	  ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
 
+config I2C_EXYNOS5
+	tristate "Exynos5 high-speed I2C driver"
+	depends on ARCH_EXYNOS5 && OF
+	help
+	  Say Y here to include support for High-speed I2C controller in the
+	  Exynos5 based Samsung SoCs.
+
 config I2C_GPIO
 	tristate "GPIO-based bitbanging I2C"
 	depends on GENERIC_GPIO
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 8f4fc23..b19366c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -42,6 +42,7 @@  i2c-designware-platform-objs := i2c-designware-platdrv.o
 obj-$(CONFIG_I2C_DESIGNWARE_PCI)	+= i2c-designware-pci.o
 i2c-designware-pci-objs := i2c-designware-pcidrv.o
 obj-$(CONFIG_I2C_EG20T)		+= i2c-eg20t.o
+obj-$(CONFIG_I2C_EXYNOS5)	+= i2c-exynos5.o
 obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
 obj-$(CONFIG_I2C_HIGHLANDER)	+= i2c-highlander.o
 obj-$(CONFIG_I2C_IBM_IIC)	+= i2c-ibm_iic.o
diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
new file mode 100644
index 0000000..e8e6483
--- /dev/null
+++ b/drivers/i2c/busses/i2c-exynos5.c
@@ -0,0 +1,871 @@ 
+/**
+ * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/debugfs.h>
+
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/of_irq.h>
+#include <linux/of_i2c.h>
+
+/*
+ * HSI2C controller from Samsung supports 2 modes of operation
+ * 1. Auto mode: Where in master automatically controls the whole transaction
+ * 2. Manual mode: Software controls the transaction by issuing commands
+ *    START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register.
+ *
+ * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register
+ *
+ * Special bits are available for both modes of operation to set commands
+ * and for checking transfer status
+ */
+
+/* Register Map */
+#define HSI2C_CTL		0x00
+#define HSI2C_FIFO_CTL		0x04
+#define HSI2C_TRAILIG_CTL	0x08
+#define HSI2C_CLK_CTL		0x0C
+#define HSI2C_CLK_SLOT		0x10
+#define HSI2C_INT_ENABLE	0x20
+#define HSI2C_INT_STATUS	0x24
+#define HSI2C_ERR_STATUS	0x2C
+#define HSI2C_FIFO_STATUS	0x30
+#define HSI2C_TX_DATA		0x34
+#define HSI2C_RX_DATA		0x38
+#define HSI2C_CONF		0x40
+#define HSI2C_AUTO_CONF		0x44
+#define HSI2C_TIMEOUT		0x48
+#define HSI2C_MANUAL_CMD	0x4C
+#define HSI2C_TRANS_STATUS	0x50
+#define HSI2C_TIMING_HS1	0x54
+#define HSI2C_TIMING_HS2	0x58
+#define HSI2C_TIMING_HS3	0x5C
+#define HSI2C_TIMING_FS1	0x60
+#define HSI2C_TIMING_FS2	0x64
+#define HSI2C_TIMING_FS3	0x68
+#define HSI2C_TIMING_SLA	0x6C
+#define HSI2C_ADDR		0x70
+
+/* I2C_CTL Register bits */
+#define HSI2C_FUNC_MODE_I2C			(1u << 0)
+#define HSI2C_MASTER				(1u << 3)
+#define HSI2C_RXCHON				(1u << 6)
+#define HSI2C_TXCHON				(1u << 7)
+#define HSI2C_SW_RST				(1u << 31)
+
+/* I2C_FIFO_CTL Register bits */
+#define HSI2C_RXFIFO_EN				(1u << 0)
+#define HSI2C_TXFIFO_EN				(1u << 1)
+#define HSI2C_TXFIFO_TRIGGER_LEVEL		(0x30 << 16)
+#define HSI2C_RXFIFO_TRIGGER_LEVEL		(0x30 << 4)
+
+/* I2C_TRAILING_CTL Register bits */
+#define HSI2C_TRAILING_COUNT			(0xf)
+
+/* I2C_INT_EN Register bits */
+#define HSI2C_INT_TX_ALMOSTEMPTY_EN		(1u << 0)
+#define HSI2C_INT_RX_ALMOSTFULL_EN		(1u << 1)
+#define HSI2C_INT_TRAILING_EN			(1u << 6)
+#define HSI2C_INT_I2C_EN			(1u << 9)
+
+/* I2C_INT_STAT Register bits */
+#define HSI2C_INT_TX_ALMOSTEMPTY		(1u << 0)
+#define HSI2C_INT_RX_ALMOSTFULL			(1u << 1)
+#define HSI2C_INT_TX_UNDERRUN			(1u << 2)
+#define HSI2C_INT_TX_OVERRUN			(1u << 3)
+#define HSI2C_INT_RX_UNDERRUN			(1u << 4)
+#define HSI2C_INT_RX_OVERRUN			(1u << 5)
+#define HSI2C_INT_TRAILING			(1u << 6)
+#define HSI2C_INT_I2C				(1u << 9)
+#define HSI2C_RX_INT				(HSI2C_INT_RX_ALMOSTFULL | \
+						 HSI2C_INT_RX_UNDERRUN | \
+						 HSI2C_INT_RX_OVERRUN | \
+						 HSI2C_INT_TRAILING)
+
+/* I2C_FIFO_STAT Register bits */
+#define HSI2C_RX_FIFO_EMPTY			(1u << 24)
+#define HSI2C_RX_FIFO_FULL			(1u << 23)
+#define HSI2C_RX_FIFO_LVL(x)			((x >> 16) & 0x7f)
+#define HSI2C_TX_FIFO_EMPTY			(1u << 8)
+#define HSI2C_TX_FIFO_FULL			(1u << 7)
+#define HSI2C_TX_FIFO_LVL(x)			((x >> 0) & 0x7f)
+#define HSI2C_FIFO_EMPTY			(HSI2C_RX_FIFO_EMPTY |	\
+						HSI2C_TX_FIFO_EMPTY)
+
+/* I2C_CONF Register bits */
+#define HSI2C_AUTO_MODE				(1u << 31)
+#define HSI2C_10BIT_ADDR_MODE			(1u << 30)
+#define HSI2C_HS_MODE				(1u << 29)
+
+/* I2C_AUTO_CONF Register bits */
+#define HSI2C_READ_WRITE			(1u << 16)
+#define HSI2C_STOP_AFTER_TRANS			(1u << 17)
+#define HSI2C_MASTER_RUN			(1u << 31)
+
+/* I2C_TIMEOUT Register bits */
+#define HSI2C_TIMEOUT_EN			(1u << 31)
+
+/* I2C_TRANS_STATUS register bits */
+#define HSI2C_MASTER_BUSY			(1u << 17)
+#define HSI2C_SLAVE_BUSY			(1u << 16)
+#define HSI2C_TIMEOUT_AUTO			(1u << 4)
+#define HSI2C_NO_DEV				(1u << 3)
+#define HSI2C_NO_DEV_ACK			(1u << 2)
+#define HSI2C_TRANS_ABORT			(1u << 1)
+#define HSI2C_TRANS_DONE			(1u << 0)
+
+/* I2C_ADDR register bits */
+#define HSI2C_SLV_ADDR_SLV(x)			((x & 0x3ff) << 0)
+#define HSI2C_SLV_ADDR_MAS(x)			((x & 0x3ff) << 10)
+#define HSI2C_MASTER_ID(x)			((x & 0xff) << 24)
+
+/* Controller operating frequency, timing values for operation
+ * are calculated against this frequency
+ */
+#define HSI2C_HS_TX_CLOCK	1000000
+#define HSI2C_FS_TX_CLOCK	1000000
+#define HSI2C_HIGH_SPD		1
+#define HSI2C_FAST_SPD		0
+
+#define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000))
+
+/* timeout for pm runtime autosuspend */
+#define EXYNOS5_I2C_PM_TIMEOUT		1000	/* ms */
+
+struct exynos5_i2c {
+	struct i2c_adapter	adap;
+	unsigned int		suspended:1;
+
+	struct i2c_msg		*msg;
+	struct completion	msg_complete;
+	unsigned int		msg_ptr;
+	unsigned int		msg_len;
+
+	unsigned int		irq;
+
+	void __iomem		*regs;
+	struct clk		*clk;
+	struct device		*dev;
+	int			state;
+
+	/* GPIO lines for SDA/SCL*/
+	int			gpios[2];
+
+	/* Controller operating frequency */
+	unsigned int		clock;
+	unsigned int		clk_cycle;
+	unsigned int		clk_div;
+
+	/* HSI2C Controller can operate in
+	 * 1. High speed upto 3.4Mbps
+	 * 2. Fast speed upto 1Mbps
+	 */
+	int			speed_mode;
+};
+
+static const struct of_device_id exynos5_i2c_match[] = {
+	{ .compatible = "samsung,exynos5-hsi2c" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
+
+static inline void exynos5_i2c_stop(struct exynos5_i2c *i2c)
+{
+	writel(0, i2c->regs + HSI2C_INT_ENABLE);
+
+	complete(&i2c->msg_complete);
+}
+
+static void exynos5_i2c_en_timeout(struct exynos5_i2c *i2c)
+{
+	u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
+
+	/* Clear to enable Timeout */
+	i2c_timeout &= ~HSI2C_TIMEOUT_EN;
+	writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
+}
+
+/* exynos5_i2c_clock_info: Calculates the clock divisor and
+ * the clock cycle length (SCLK High + SCLK Low)
+ *
+ * Returns 0 on success,  -EINVAL if the cycle length cannot
+ * be calculated.
+ */
+static int exynos5_i2c_clock_info(struct exynos5_i2c *i2c)
+{
+	unsigned int op_clk = i2c->clock;
+	unsigned int clkin = clk_get_rate(i2c->clk);
+	unsigned int i, utemp0 = 0, utemp1 = 0, utemp2 = 0;
+	unsigned int t_ftl_cycle;
+
+	/* FPCLK / FI2C =
+	 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
+	 * utemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
+	 * utemp1 = (TSCLK_L + TSCLK_H + 2)
+	 * utemp2 = TSCLK_L + TSCLK_H
+	 */
+	t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
+	utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
+
+	/* CLK_DIV max is 256 */
+	for (i = 0; i < 256; i++) {
+		utemp1 = utemp0 / (i + 1);
+		/* SCLK_L/H max is 256 / 2 */
+		if (utemp1 < 128) {
+			utemp2 = utemp1 - 2;
+			break;
+		}
+	}
+
+	if (utemp2 <= 0)
+		return -EINVAL;
+
+	i2c->clk_cycle = utemp2;
+	i2c->clk_div = i;
+
+	return 0;
+}
+
+/* exynos5_i2c_set_timing: updates the registers with appropriate
+ * timing values calculated earlier (exynos5_i2c_clock_info)
+ *
+ * To handle the error case in calculates and to avoid the subsequent
+ * calculates the clk_div and clk_cycle are stored
+ */
+static void exynos5_i2c_set_timing(struct exynos5_i2c *i2c)
+{
+	u32 i2c_timing_s1;
+	u32 i2c_timing_s2;
+	u32 i2c_timing_s3;
+	u32 i2c_timing_sla;
+	unsigned int n_clkdiv;
+	unsigned int t_start_su, t_start_hd;
+	unsigned int t_stop_su;
+	unsigned int t_data_su, t_data_hd;
+	unsigned int t_scl_l, t_scl_h;
+	unsigned int t_sr_release;
+
+	n_clkdiv = i2c->clk_div;
+	t_scl_l = i2c->clk_cycle / 2;
+	t_scl_h = i2c->clk_cycle / 2;
+	t_start_su = t_scl_l;
+	t_start_hd = t_scl_l;
+	t_stop_su = t_scl_l;
+	t_data_su = t_scl_l / 2;
+	t_data_hd = t_scl_l / 2;
+	t_sr_release = i2c->clk_cycle;
+
+	i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
+	i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
+	i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
+	i2c_timing_sla = t_data_hd << 0;
+
+	dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
+		t_start_su, t_start_hd, t_stop_su);
+	dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
+		t_data_su, t_scl_l, t_scl_h);
+	dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
+		n_clkdiv, t_sr_release);
+	dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
+
+	if (i2c->speed_mode == HSI2C_HIGH_SPD) {
+		writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
+		writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
+		writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
+	} else {
+		writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
+		writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
+		writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
+	}
+	writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
+}
+
+/* exynos5_i2c_init: configures the controller for I2C functionality
+ * Programs I2C controller for Master mode operation
+ *
+ * Note: Currently, supports AUTO mode of operation.
+ */
+static void exynos5_i2c_init(struct exynos5_i2c *i2c)
+{
+	u32 i2c_conf = readl(i2c->regs + HSI2C_CONF);
+
+	writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
+					i2c->regs + HSI2C_CTL);
+	writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL);
+
+	exynos5_i2c_set_timing(i2c);
+
+	if (i2c->speed_mode == HSI2C_HIGH_SPD)
+		i2c_conf |= HSI2C_HS_MODE;
+
+	writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF);
+}
+
+static void exynos5_i2c_reset(struct exynos5_i2c *i2c)
+{
+	u32 i2c_ctl;
+
+	/* Set and clear the bit for reset */
+	i2c_ctl = readl(i2c->regs + HSI2C_CTL);
+	i2c_ctl |= HSI2C_SW_RST;
+	writel(i2c_ctl, i2c->regs + HSI2C_CTL);
+
+	i2c_ctl = readl(i2c->regs + HSI2C_CTL);
+	i2c_ctl &= ~HSI2C_SW_RST;
+	writel(i2c_ctl, i2c->regs + HSI2C_CTL);
+
+	/* Initialize the configure registers */
+	exynos5_i2c_init(i2c);
+}
+
+static void exynos5_i2c_master_run(struct exynos5_i2c *i2c)
+{
+	/* Start data transfer in Master mode */
+	u32 i2c_auto_conf = readl(i2c->regs + HSI2C_AUTO_CONF);
+	i2c_auto_conf |= HSI2C_MASTER_RUN;
+	writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
+}
+
+/* exynos5_i2c_irq: top level IRQ servicing routine
+ *
+ * INT_STATUS registers gives the interrupt details. Further,
+ * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed
+ * state of the bus.
+ */
+static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
+{
+	struct exynos5_i2c *i2c = dev_id;
+	u32 fifo_level, int_status, fifo_status, trans_status;
+	unsigned char byte;
+	int len = 0;
+
+	i2c->state = -EINVAL;
+
+	int_status = readl(i2c->regs + HSI2C_INT_STATUS);
+	fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
+
+	if (int_status & HSI2C_INT_I2C) {
+		trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
+		if (trans_status & HSI2C_NO_DEV_ACK) {
+			dev_dbg(i2c->dev, "No ACK from device\n");
+			i2c->state = -ENXIO;
+		} else if (trans_status & HSI2C_NO_DEV) {
+			dev_dbg(i2c->dev, "No device\n");
+			i2c->state = -ENXIO;
+		} else if (trans_status & HSI2C_TRANS_ABORT) {
+			dev_dbg(i2c->dev, "Deal with arbitration lose\n");
+			i2c->state = -EAGAIN;
+		} else if (trans_status & HSI2C_TIMEOUT_AUTO) {
+			dev_dbg(i2c->dev, "Accessing device timed out\n");
+			i2c->state = -EAGAIN;
+		}
+	}
+	/* TX_ALMOSTEMPTY can happen along with HSI2C_INT_I2C */
+	else if (int_status &
+			(HSI2C_INT_TX_UNDERRUN | HSI2C_INT_TX_ALMOSTEMPTY)) {
+		fifo_level = HSI2C_TX_FIFO_LVL(fifo_status);
+
+		/* To support probing the devices for detection */
+		if (i2c->msg->len == 0) {
+			i2c->state = -ENXIO;
+			goto stop;
+		}
+
+		/* 0x30 is the default trigger level for TX FIFO */
+		len = 48 - fifo_level;
+
+		if (len > i2c->msg->len)
+			len = i2c->msg->len;
+
+		i2c->msg_len += len;
+		while (len > 0) {
+			byte = i2c->msg->buf[i2c->msg_ptr++];
+			writel(byte, i2c->regs + HSI2C_TX_DATA);
+			len--;
+		}
+		i2c->state = 0;
+		goto stop;
+	}
+	/* If TX FIFO is full (give chance to clear) */
+	else if (int_status & HSI2C_INT_TX_OVERRUN)
+		i2c->state = 0;
+
+	if (int_status & (HSI2C_INT_RX_OVERRUN | HSI2C_INT_TRAILING |
+		HSI2C_INT_RX_UNDERRUN | HSI2C_INT_RX_ALMOSTFULL)) {
+		fifo_level = HSI2C_RX_FIFO_LVL(fifo_status);
+
+		if (fifo_level >= i2c->msg->len)
+			len = i2c->msg->len;
+		else
+			len = fifo_level;
+
+		i2c->msg_len += len;
+		while (len > 0) {
+			byte = (unsigned char)
+				readl(i2c->regs + HSI2C_RX_DATA);
+			i2c->msg->buf[i2c->msg_ptr++] = byte;
+			len--;
+		}
+		i2c->state = 0;
+	}
+
+
+ stop:
+	if ((i2c->msg_len == i2c->msg->len) || (i2c->state < 0))
+		exynos5_i2c_stop(i2c);
+
+	/* Set these bits to clear them */
+	writel(readl(i2c->regs + HSI2C_INT_STATUS),
+				i2c->regs + HSI2C_INT_STATUS);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * exynos5_i2c_message_start: Configures the bus and starts the xfer
+ * i2c: struct exynos5_i2c pointer for the current bus
+ * stop: Enables stop after transfer if set. Set for last transfer of
+ *       in the list of messages.
+ *
+ * Configures the bus for read/write function
+ * Sets chip address to talk to, message length to be sent.
+ * Enables appropriate interrupts and sends start xfer command.
+ */
+static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
+{
+	u32 i2c_ctl;
+	u32 int_en = HSI2C_INT_I2C_EN;
+	u32 i2c_auto_conf;
+	u32 fifo_ctl;
+
+	exynos5_i2c_en_timeout(i2c);
+
+	fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN |
+		HSI2C_TXFIFO_TRIGGER_LEVEL | HSI2C_RXFIFO_TRIGGER_LEVEL;
+	writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
+
+	i2c_ctl = readl(i2c->regs + HSI2C_CTL);
+	i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON);
+
+	if (i2c->msg->flags & I2C_M_RD) {
+		i2c_ctl |= HSI2C_RXCHON;
+
+		i2c_auto_conf |= HSI2C_READ_WRITE;
+
+		int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
+			HSI2C_INT_TRAILING_EN);
+	} else {
+		i2c_ctl |= HSI2C_TXCHON;
+
+		int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
+	}
+
+	if (stop == 1)
+		i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
+
+	writel(HSI2C_SLV_ADDR_MAS(i2c->msg->addr), i2c->regs + HSI2C_ADDR);
+
+	writel(i2c_ctl, i2c->regs + HSI2C_CTL);
+
+	/* In auto mode the length of xfer cannot be 0 */
+	if (i2c->msg->len == 0)
+		i2c_auto_conf |= 0x1;
+	else
+		i2c_auto_conf |= i2c->msg->len;
+
+	writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
+
+	exynos5_i2c_master_run(i2c);
+
+	writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
+}
+
+static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c,
+			      struct i2c_msg *msgs, int stop)
+{
+	unsigned long timeout;
+	int ret;
+
+	i2c->msg = msgs;
+	i2c->msg_ptr = 0;
+	i2c->msg_len = 0;
+
+	exynos5_i2c_message_start(i2c, stop);
+
+	ret = wait_for_completion_interruptible_timeout
+		(&i2c->msg_complete, EXYNOS5_I2C_TIMEOUT);
+	if (ret >= 0)
+		timeout = ret;
+	else
+		return ret;
+
+	ret = i2c->state;
+
+	if (timeout == 0) {
+		exynos5_i2c_reset(i2c);
+		dev_warn(i2c->dev, "%s timeout\n",
+			(msgs->flags & I2C_M_RD) ? "rx" : "tx");
+		return ret;
+	}
+
+	if (ret == -EAGAIN) {
+		exynos5_i2c_reset(i2c);
+		return ret;
+	}
+
+	return ret;
+}
+
+static int exynos5_i2c_xfer(struct i2c_adapter *adap,
+			struct i2c_msg *msgs, int num)
+{
+	struct exynos5_i2c *i2c = (struct exynos5_i2c *)adap->algo_data;
+	struct i2c_msg *msgs_ptr = msgs;
+	int retry, i = 0;
+	int ret, ret_pm;
+	int stop = 0;
+
+	if (i2c->suspended) {
+		dev_err(i2c->dev, "HS-I2C is not initialzed.\n");
+		return -EIO;
+	}
+
+	ret_pm = pm_runtime_get_sync(i2c->dev);
+	if (IS_ERR_VALUE(ret_pm)) {
+		ret = -EIO;
+		goto out;
+	}
+
+	clk_prepare_enable(i2c->clk);
+
+	for (retry = 0; retry < adap->retries; retry++) {
+		for (i = 0; i < num; i++) {
+			stop = (i == num - 1);
+
+			ret = exynos5_i2c_xfer_msg(i2c, msgs_ptr, stop);
+			msgs_ptr++;
+
+			if (ret == -EAGAIN) {
+				msgs_ptr = msgs;
+				break;
+			} else if (ret < 0) {
+				goto out;
+			}
+		}
+
+		if ((i == num) && (ret != -EAGAIN))
+			break;
+
+		dev_dbg(i2c->dev, "retrying transfer (%d)\n", retry);
+
+		udelay(100);
+	}
+
+ check:
+	if (i == num) {
+		/* only one message, return number of bytes transfered */
+		if (num == 1)
+			ret = i2c->msg_len;
+		else
+			ret = num;
+	} else {
+		/* Only one message, cannot access the device */
+		if (i == 1)
+			ret = -EREMOTEIO;
+		else
+			ret = i;
+
+		dev_warn(i2c->dev, "xfer message failed\n");
+	}
+
+ out:
+	clk_disable_unprepare(i2c->clk);
+	pm_runtime_mark_last_busy(i2c->dev);
+	pm_runtime_put_autosuspend(i2c->dev);
+	return ret;
+}
+
+static u32 exynos5_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm exynos5_i2c_algorithm = {
+	.master_xfer		= exynos5_i2c_xfer,
+	.functionality		= exynos5_i2c_func,
+};
+
+/**
+ * Parse a list of GPIOs from a node property and request each one
+ *
+ * @param i2c		i2c driver data
+ * @return 0 on success, -EINVAL on error, in which case no GPIOs requested
+*/
+static int exynos5_i2c_parse_dt_gpio(struct exynos5_i2c *i2c)
+{
+	int idx, gpio, ret;
+
+	for (idx = 0; idx < 2; idx++) {
+		gpio = of_get_gpio(i2c->dev->of_node, idx);
+		if (!gpio_is_valid(gpio)) {
+			dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio);
+			return -EINVAL;
+		}
+		i2c->gpios[idx] = gpio;
+
+		ret = devm_gpio_request(i2c->dev, gpio, "i2c-bus");
+		if (ret) {
+			dev_err(i2c->dev, "gpio [%d] request failed\n", gpio);
+			return -EINVAL;
+		}
+	}
+	return 0;
+}
+
+#define HSI2C_REG(regname) {.name = #regname, .offset = regname}
+static struct debugfs_reg32 exynos5_hsi2c_regs[] = {
+	HSI2C_REG(HSI2C_CTL), HSI2C_REG(HSI2C_FIFO_CTL),
+	HSI2C_REG(HSI2C_TRAILIG_CTL), HSI2C_REG(HSI2C_CLK_CTL),
+	HSI2C_REG(HSI2C_CLK_SLOT), HSI2C_REG(HSI2C_INT_ENABLE),
+	HSI2C_REG(HSI2C_INT_STATUS), HSI2C_REG(HSI2C_ERR_STATUS),
+	HSI2C_REG(HSI2C_FIFO_STATUS), HSI2C_REG(HSI2C_TX_DATA),
+	HSI2C_REG(HSI2C_RX_DATA), HSI2C_REG(HSI2C_CONF),
+	HSI2C_REG(HSI2C_AUTO_CONF), HSI2C_REG(HSI2C_TIMEOUT),
+	HSI2C_REG(HSI2C_MANUAL_CMD), HSI2C_REG(HSI2C_TRANS_STATUS),
+	HSI2C_REG(HSI2C_TIMING_HS1), HSI2C_REG(HSI2C_TIMING_HS2),
+	HSI2C_REG(HSI2C_TIMING_HS3), HSI2C_REG(HSI2C_TIMING_FS1),
+	HSI2C_REG(HSI2C_TIMING_FS2), HSI2C_REG(HSI2C_TIMING_FS3),
+	HSI2C_REG(HSI2C_TIMING_SLA), HSI2C_REG(HSI2C_ADDR),
+};
+
+static struct debugfs_regset32 exynos5_hsi2c_regset = {
+	.regs = exynos5_hsi2c_regs,
+	.nregs = ARRAY_SIZE(exynos5_hsi2c_regs),
+};
+
+static struct dentry *exynos5_hsi2c_reg_debugfs;
+
+static int exynos5_i2c_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct exynos5_i2c *i2c;
+	int ret;
+
+	if (!np) {
+		dev_err(&pdev->dev, "no device node\n");
+		return -ENOENT;
+	}
+
+	i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
+	if (!i2c) {
+		dev_err(&pdev->dev, "no memory for state\n");
+		return -ENOMEM;
+	}
+
+	/* Mode of operation High/Fast Speed mode */
+	if (of_get_property(np, "samsung,hs-mode", NULL)) {
+		i2c->speed_mode = 1;
+		if (of_property_read_u32(np, "samsung,hs-clock", &i2c->clock))
+			i2c->clock = HSI2C_HS_TX_CLOCK;
+	} else {
+		i2c->speed_mode = 0;
+		if (of_property_read_u32(np, "samsung,fs-clock", &i2c->clock))
+			i2c->clock = HSI2C_FS_TX_CLOCK;
+	}
+
+	strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name));
+	i2c->adap.owner   = THIS_MODULE;
+	i2c->adap.algo    = &exynos5_i2c_algorithm;
+	i2c->adap.retries = 2;
+	i2c->adap.class   = I2C_CLASS_HWMON | I2C_CLASS_SPD;
+
+	i2c->dev = &pdev->dev;
+	i2c->clk = devm_clk_get(&pdev->dev, "hsi2c");
+	if (IS_ERR(i2c->clk)) {
+		dev_err(&pdev->dev, "cannot get clock\n");
+		return -ENOENT;
+	}
+
+	clk_prepare_enable(i2c->clk);
+
+	i2c->regs = of_iomap(np, 0);
+	if (!i2c->regs) {
+		dev_err(&pdev->dev, "cannot map HS-I2C IO\n");
+		ret = -EADDRNOTAVAIL;
+		goto err_clk;
+	}
+
+	i2c->adap.algo_data = i2c;
+	i2c->adap.dev.parent = &pdev->dev;
+
+	/* parse device tree and inititalise the gpio */
+	if (exynos5_i2c_parse_dt_gpio(i2c))
+		return -EINVAL;
+
+	init_completion(&i2c->msg_complete);
+
+	i2c->irq = ret = irq_of_parse_and_map(np, 0);
+	if (ret <= 0) {
+		dev_err(&pdev->dev, "cannot find HS-I2C IRQ\n");
+		goto err_iomap;
+	}
+
+	ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
+				0, dev_name(&pdev->dev), i2c);
+
+	if (ret != 0) {
+		dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq);
+		goto err_iomap;
+	}
+
+	/*
+	 * TODO: Use private lock to avoid race conditions as
+	 * mentioned in pm_runtime.txt
+	 */
+	pm_runtime_enable(i2c->dev);
+	pm_runtime_set_autosuspend_delay(i2c->dev, EXYNOS5_I2C_PM_TIMEOUT);
+	pm_runtime_use_autosuspend(i2c->dev);
+
+	ret = pm_runtime_get_sync(i2c->dev);
+	if (IS_ERR_VALUE(ret))
+		goto err_iomap;
+
+	ret = exynos5_i2c_clock_info(i2c);
+	if (ret)
+		goto err_pm;
+
+	exynos5_i2c_init(i2c);
+
+	i2c->adap.nr = -1;
+	i2c->adap.dev.of_node = np;
+
+	ret = i2c_add_numbered_adapter(&i2c->adap);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to add bus to i2c core\n");
+		goto err_pm;
+	}
+
+	of_i2c_register_devices(&i2c->adap);
+	platform_set_drvdata(pdev, i2c);
+
+	exynos5_hsi2c_reg_debugfs = debugfs_create_regset32("exynos5-hsi2c",
+						  S_IFREG | S_IRUGO,
+						  NULL, &exynos5_hsi2c_regset);
+	clk_disable_unprepare(i2c->clk);
+	pm_runtime_mark_last_busy(i2c->dev);
+	pm_runtime_put_autosuspend(i2c->dev);
+
+	return 0;
+
+ err_pm:
+	pm_runtime_put(i2c->dev);
+	pm_runtime_disable(&pdev->dev);
+ err_iomap:
+	iounmap(i2c->regs);
+ err_clk:
+	clk_disable_unprepare(i2c->clk);
+	return ret;
+}
+
+static int exynos5_i2c_remove(struct platform_device *pdev)
+{
+	struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = pm_runtime_get_sync(&pdev->dev);
+	if (IS_ERR_VALUE(ret))
+		return ret;
+
+	clk_disable_unprepare(i2c->clk);
+	pm_runtime_put(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	i2c_del_adapter(&i2c->adap);
+
+	iounmap(i2c->regs);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int exynos5_i2c_suspend_noirq(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+
+	i2c->suspended = 1;
+
+	return 0;
+}
+
+static int exynos5_i2c_resume_noirq(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+
+	clk_prepare_enable(i2c->clk);
+	exynos5_i2c_init(i2c);
+	clk_disable_unprepare(i2c->clk);
+	i2c->suspended = 0;
+
+	return 0;
+}
+
+static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
+	.suspend_noirq = exynos5_i2c_suspend_noirq,
+	.resume_noirq	= exynos5_i2c_resume_noirq,
+};
+
+#define EXYNOS5_DEV_PM_OPS (&exynos5_i2c_dev_pm_ops)
+#else
+#define EXYNOS5_DEV_PM_OPS NULL
+#endif
+
+static struct platform_driver exynos5_i2c_driver = {
+	.probe		= exynos5_i2c_probe,
+	.remove		= exynos5_i2c_remove,
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= "exynos5-hsi2c",
+		.pm	= EXYNOS5_DEV_PM_OPS,
+		.of_match_table = of_match_ptr(exynos5_i2c_match),
+	},
+};
+
+static int __init i2c_adap_exynos5_init(void)
+{
+	return platform_driver_register(&exynos5_i2c_driver);
+}
+subsys_initcall(i2c_adap_exynos5_init);
+
+static void __exit i2c_adap_exynos5_exit(void)
+{
+	platform_driver_unregister(&exynos5_i2c_driver);
+}
+module_exit(i2c_adap_exynos5_exit);
+
+MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
+MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>");
+MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>");
+MODULE_LICENSE("GPL");