[V4,1/3] pci: Add PCIe driver for Samsung Exynos

Message ID	003601ce6756$444e8cd0$cceba670$@samsung.com (mailing list archive)
State	New, archived
Delegated to:	Bjorn Helgaas
Headers	show Return-Path: <linux-pci-owner@vger.kernel.org> From: Jingoo Han <jg1.han@samsung.com> To: 'Kukjin Kim' <kgene.kim@samsung.com>, 'Bjorn Helgaas' <bhelgaas@google.com> Cc: linux-samsung-soc@vger.kernel.org, linux-pci@vger.kernel.org, devicetree-discuss@lists.ozlabs.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, 'Grant Likely' <grant.likely@secretlab.ca>, 'Andrew Murray' <andrew.murray@arm.com>, 'Thomas Petazzoni' <thomas.petazzoni@free-electrons.com>, 'Thierry Reding' <thierry.reding@avionic-design.de>, 'Jason Gunthorpe' <jgunthorpe@obsidianresearch.com>, 'Arnd Bergmann' <arnd@arndb.de>, 'Surendranath Gurivireddy Balla' <suren.reddy@samsung.com>, 'Siva Reddy Kallam' <siva.kallam@samsung.com>, 'Thomas Abraham' <thomas.abraham@linaro.org>, Jingoo Han <jg1.han@samsung.com> Subject: [PATCH V4 1/3] pci: Add PCIe driver for Samsung Exynos Date: Wed, 12 Jun 2013 19:19:05 +0900 Message-id: <003601ce6756$444e8cd0$cceba670$@samsung.com> MIME-version: 1.0 Content-type: text/plain; charset=us-ascii Content-transfer-encoding: 7bit Thread-index: Ac5nVjNORMJv0/E0Q/+5Aq+bmnypAg== Content-language: ko DLP-Filter: Pass Sender: linux-pci-owner@vger.kernel.org Precedence: bulk

On Wednesday, June 12, 2013 8:23 PM, Arnd Bergmann wrote: > On Wednesday 12 June 2013 19:19:05 Jingoo Han wrote: > > > + > > +struct pcie_port { > > + struct device *dev; > > + u8 controller; > > + u8 root_bus_nr; > > + void __iomem *dbi_base; > > + void __iomem *elbi_base; > > + void __iomem *phy_base; > > + void __iomem *purple_base; > > + phys_addr_t cfg0_base; > > + void __iomem *va_cfg0_base; > > + phys_addr_t cfg1_base; > > + void __iomem *va_cfg1_base; > > + phys_addr_t io_base; > > + phys_addr_t mem_base; > > + spinlock_t conf_lock; > > + struct resource cfg; > > + struct resource io; > > + struct resource mem; > > + struct pcie_port_info config; > > + struct clk *clk; > > + struct clk *bus_clk; > > + int irq; > > + int reset_gpio; > > +}; > > This looks much better now. > > > + > > +/* synopsis specific PCIE configuration registers*/ > > +#define PCIE_PORT_LINK_CONTROL 0x710 > > +#define PORT_LINK_MODE_MASK (0x3f << 16) > > +#define PORT_LINK_MODE_4_LANES (0x7 << 16) > > Do you mean this is a "Synopsys" designware part? In that case it > should really not be called "exynos-pcie" but "designware-pcie" > and you should make sure that the driver makes no assumptions about > the platform. A lot of other platforms also use designware > parts and should be able to reuse this driver. Sorry, I don't think so. Only core block is a "Synopsys" designware part IP block, other parts are Exynos-specific. So, it is hard to share with other PCIe IPs using synopsis core. > > > +static void exynos_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev) > > +{ > > + u32 val; > > + void __iomem *dbi_base = pp->dbi_base; > > + > > + /* Program viewport 0 : OUTBOUND : CFG0 */ > > + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > + writel_rc(pp, (u32)pp->cfg0_base, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > + writel_rc(pp, (u32)pp->cfg0_base + pp->config.cfg0_size - 1, > > + dbi_base + PCIE_ATU_LIMIT); > > + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > + writel_rc(pp, PCIE_ATU_TYPE_CFG0, dbi_base + PCIE_ATU_CR1); > > + val = PCIE_ATU_ENABLE; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > +} > > I think you should not assume that the physical base address is a 32 > bit value. The hardware clearly supports "lower" and "upper" halves > for the address window, so when resource_size_t is 64 bit, you should > set the upper half accordingly. Since the hardware is always 64 bit, > you can use a "u64" type rather than resource_size_t to simplify the > code here. OK, I will replace "u32" with "u64". > > > +static void exynos_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) > > +{ > > + u32 val; > > + void __iomem *dbi_base = pp->dbi_base; > > + > > + /* Program viewport 0 : OUTBOUND : MEM */ > > + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); > > + val = PCIE_ATU_ENABLE; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > + writel_rc(pp, (u32)pp->mem_base, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > + writel_rc(pp, (u32)(pp->mem_base + pp->config.mem_size - 1), > > + dbi_base + PCIE_ATU_LIMIT); > > + writel_rc(pp, (u32)pp->mem_base, dbi_base + PCIE_ATU_LOWER_TARGET); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > +} > > You probably should not assume that there is a 1:1 mapping between > bus addresses and host physical addresses, but rather read both > values from the DT individually. With the ranges defined as > > 0x82000000 0 0x40210000 0x40210000 0 0x10000000>; /* non-prefetchable memory */ > > the second and third cell should go into > PCIE_ATU_UPPER_TARGET/PCIE_ATU_LOWER_TARGET, while the translated address > (from the third cell) should go into PCIE_ATU_LOWER_BASE/PCIE_ATU_UPPER_BASE > > The PCIE_ATU_LIMIT seems to correctly get translated from the last > cell. OK, I will change it. > > > +static void exynos_pcie_prog_viewport_io_outbound(struct pcie_port *pp) > > +{ > > + u32 val; > > + void __iomem *dbi_base = pp->dbi_base; > > + > > + /* Program viewport 1 : OUTBOUND : IO */ > > + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); > > + val = PCIE_ATU_ENABLE; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > + writel_rc(pp, (u32)pp->io_base, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > + writel_rc(pp, (u32)(pp->io_base + pp->config.io_size - 1), > > + dbi_base + PCIE_ATU_LIMIT); > > + writel_rc(pp, (u32)pp->io_base, dbi_base + PCIE_ATU_LOWER_TARGET); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > +} > > You don't actually map the I/O space anywhere into virtual memory. > I think you need to call pci_ioremap_io with the pp->io_base at > boot time. Sorry, when pci_ioremap_io() is used, Exynos5440 hangs. I don't know how to deal this. > > I think you mixed up the PCIE_ATU_LOWER_TARGET, it should really be 0, > since all I/O port numbers have to be smaller than IO_SPACE_LIMIT. > > The first argument to pci_ioremap_io needs to be unique for each > domain and you need to use it to calculate the io_offset you > set in pci_sys_data->io_offset. > > > +static void exynos_pcie_prog_viewport_mem_inbound(struct pcie_port *pp) > > +{ > > + u32 val; > > + void __iomem *dbi_base = pp->dbi_base; > > + struct pcie_port_info *config = &pp->config; > > + > > + /* Program viewport 0 : INBOUND : MEMORY */ > > + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX0; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); > > + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > + writel_rc(pp, config->in_mem_size - 1, dbi_base + PCIE_ATU_LIMIT); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_TARGET); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > +} > > You hardcode the in_mem_size to 256 MB. Does that mean you only allow > PCI bus master DMA on the first part of RAM? Shouldn't it get > computed from the actual location and size of RAM? I will remove the hard-coded in_mem_size, instead use the size of MEM region. > > > +static void exynos_pcie_prog_viewport_io_inbound(struct pcie_port *pp) > > +{ > > + u32 val; > > + void __iomem *dbi_base = pp->dbi_base; > > + struct pcie_port_info *config = &pp->config; > > + > > + /* Program viewport 1 : INBOUND : IO */ > > + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX1; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); > > + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > + writel_rc(pp, config->in_mem_size - 1, dbi_base + PCIE_ATU_LIMIT); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_TARGET); > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > +} > > I don't understand what in inbound I/O access actually means. What > does this do, is it for PCI target emulation? I reviewed the manual, and I will fix it. I will add bus addresses and host physical addresses to PCIE_ATU_LOWER_BASE/ PCIE_ATU_LOWER_TARGET. > > > + > > +static int exynos_pcie_setup(int nr, struct pci_sys_data *sys) > > +{ > > + struct pcie_port *pp; > > + > > + pp = sys_to_pcie(sys); > > + > > + if (!pp) > > + return 0; > > + > > + pci_add_resource_offset(&sys->resources, &pp->io, sys->io_offset); > > + pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset); > > + > > + return 1; > > +} > > You don't actually set up io_offset and mem_offset, right? OK, I will replace pci_add_resource_offset() with pci_add_resource(). Best regards, Jingoo Han > > Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html

diff --git a/Documentation/devicetree/bindings/pci/exynos-pcie.txt b/Documentation/devicetree/bindings/pci/exynos-pcie.txt new file mode 100644 index 0000000..f78a52b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/exynos-pcie.txt @@ -0,0 +1,71 @@ +* Samsung Exynos PCIe interface + +Required properties: +-compatible: should be "samsung,exynos5440-pcie" +-reg: base addresses and lengths of the pcie conteroller, + the phy controller, additional register for the phy controller. +- interrupts: interrupt values for level interrupt, + pulse interrupt, special interrupt. +- clocks: from common clock binding: handle to pci clock. +- clock-names: from common clock binding: Shall be "pcie", "pcie_bus". +- #address-cells, set to <3> +- #size-cells, set to <2> +- device_type, set to "pci" +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells, set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- reset-gpio: gpio pin number of power good signal + +Example: + +SoC specific DT Entry: + + pcie0@0x290000 { + compatible = "samsung,exynos5440-pcie"; + reg = <0x290000 0x1000 + 0x270000 0x1000 + 0x271000 0x40>; + interrupts = <0 20 0>, <0 21 0>, <0 22 0>; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00200000 /* configuration space */ + 0x81000000 0 0 0x40200000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x40210000 0x40210000 0 0x10000000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 53>; + }; + + pcie1@2a0000 { + compatible = "samsung,exynos5440-pcie"; + reg = <0x2a0000 0x1000 + 0x272000 0x1000 + 0x271040 0x40>; + interrupts = <0 23 0>, <0 24 0>, <0 25 0>; + clocks = <&clock 29>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00200000 /* configuration space */ + 0x81000000 0 0 0x60200000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x60210000 0x60210000 0 0x10000000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 56>; + }; + +Board specific DT Entry: + + pcie0@40000000 { + reset-gpio = <5>; + }; + + pcie1@60000000 { + reset-gpio = <22>; + }; diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 1f1d67f..fec0f1f 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -5,4 +5,9 @@ config PCI_MVEBU bool "Marvell EBU PCIe controller" depends on ARCH_MVEBU || ARCH_KIRKWOOD +config PCI_EXYNOS + bool "Samsung Exynos PCIe controller" + depends on SOC_EXYNOS5440 + select PCIEPORTBUS + endmenu diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index 5ea2d8b..31d77ad 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -1 +1,2 @@ obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o +obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o diff --git a/drivers/pci/host/pci-exynos.c b/drivers/pci/host/pci-exynos.c new file mode 100644 index 0000000..93e058a --- /dev/null +++ b/drivers/pci/host/pci-exynos.c @@ -0,0 +1,1074 @@ +/* + * PCIe host controller driver for Samsung EXYNOS SoCs + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Author: Jingoo Han <jg1.han@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_pci.h> +#include <linux/pci.h> +#include <linux/pci_regs.h> +#include <linux/platform_device.h> +#include <linux/resource.h> +#include <linux/signal.h> +#include <linux/slab.h> +#include <linux/types.h> + +struct pcie_port_info { + u32 cfg0_size; + u32 cfg1_size; + u32 io_size; + u32 mem_size; + u32 in_mem_size; +}; + +struct pcie_port { + struct device *dev; + u8 controller; + u8 root_bus_nr; + void __iomem *dbi_base; + void __iomem *elbi_base; + void __iomem *phy_base; + void __iomem *purple_base; + phys_addr_t cfg0_base; + void __iomem *va_cfg0_base; + phys_addr_t cfg1_base; + void __iomem *va_cfg1_base; + phys_addr_t io_base; + phys_addr_t mem_base; + spinlock_t conf_lock; + struct resource cfg; + struct resource io; + struct resource mem; + struct pcie_port_info config; + struct clk *clk; + struct clk *bus_clk; + int irq; + int reset_gpio; +}; + +/* synopsis specific PCIE configuration registers*/ +#define PCIE_PORT_LINK_CONTROL 0x710 +#define PORT_LINK_MODE_MASK (0x3f << 16) +#define PORT_LINK_MODE_4_LANES (0x7 << 16) + +#define PCIE_LINK_WIDTH_SPEED_CONTROL 0x80C +#define PORT_LOGIC_SPEED_CHANGE (0x1 << 17) +#define PORT_LOGIC_LINK_WIDTH_MASK (0x1ff << 8) +#define PORT_LOGIC_LINK_WIDTH_4_LANES (0x7 << 8) + +#define PCIE_MSI_ADDR_LO 0x820 +#define PCIE_MSI_ADDR_HI 0x824 +#define PCIE_MSI_INTR0_ENABLE 0x828 +#define PCIE_MSI_INTR0_MASK 0x82C +#define PCIE_MSI_INTR0_STATUS 0x830 + +#define PCIE_ATU_VIEWPORT 0x900 +#define PCIE_ATU_REGION_INBOUND (0x1 << 31) +#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31) +#define PCIE_ATU_REGION_INDEX1 (0x1 << 0) +#define PCIE_ATU_REGION_INDEX0 (0x0 << 0) +#define PCIE_ATU_CR1 0x904 +#define PCIE_ATU_TYPE_MEM (0x0 << 0) +#define PCIE_ATU_TYPE_IO (0x2 << 0) +#define PCIE_ATU_TYPE_CFG0 (0x4 << 0) +#define PCIE_ATU_TYPE_CFG1 (0x5 << 0) +#define PCIE_ATU_CR2 0x908 +#define PCIE_ATU_ENABLE (0x1 << 31) +#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30) +#define PCIE_ATU_LOWER_BASE 0x90C +#define PCIE_ATU_UPPER_BASE 0x910 +#define PCIE_ATU_LIMIT 0x914 +#define PCIE_ATU_LOWER_TARGET 0x918 +#define PCIE_ATU_BUS(x) (((x) & 0xff) << 24) +#define PCIE_ATU_DEV(x) (((x) & 0x1f) << 19) +#define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16) +#define PCIE_ATU_UPPER_TARGET 0x91C + +/* PCIe ELBI registers */ +#define PCIE_IRQ_PULSE 0x000 +#define IRQ_INTA_ASSERT (0x1 << 0) +#define IRQ_INTB_ASSERT (0x1 << 2) +#define IRQ_INTC_ASSERT (0x1 << 4) +#define IRQ_INTD_ASSERT (0x1 << 6) +#define PCIE_IRQ_LEVEL 0x004 +#define PCIE_IRQ_SPECIAL 0x008 +#define PCIE_IRQ_EN_PULSE 0x00c +#define PCIE_IRQ_EN_LEVEL 0x010 +#define PCIE_IRQ_EN_SPECIAL 0x014 +#define PCIE_PWR_RESET 0x018 +#define PCIE_CORE_RESET 0x01c +#define PCIE_CORE_RESET_ENABLE (0x1 << 0) +#define PCIE_STICKY_RESET 0x020 +#define PCIE_NONSTICKY_RESET 0x024 +#define PCIE_APP_INIT_RESET 0x028 +#define PCIE_APP_LTSSM_ENABLE 0x02c +#define PCIE_ELBI_RDLH_LINKUP 0x064 +#define PCIE_ELBI_LTSSM_ENABLE 0x1 +#define PCIE_ELBI_SLV_AWMISC 0x11c +#define PCIE_ELBI_SLV_ARMISC 0x120 +#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21) + +/* PCIe Purple registers */ +#define PCIE_PHY_GLOBAL_RESET 0x000 +#define PCIE_PHY_COMMON_RESET 0x004 +#define PCIE_PHY_CMN_REG 0x008 +#define PCIE_PHY_MAC_RESET 0x00c +#define PCIE_PHY_PLL_LOCKED 0x010 +#define PCIE_PHY_TRSVREG_RESET 0x020 +#define PCIE_PHY_TRSV_RESET 0x024 + +/* PCIe PHY registers */ +#define PCIE_PHY_IMPEDANCE 0x004 +#define PCIE_PHY_PLL_DIV_0 0x008 +#define PCIE_PHY_PLL_BIAS 0x00c +#define PCIE_PHY_DCC_FEEDBACK 0x014 +#define PCIE_PHY_PLL_DIV_1 0x05c +#define PCIE_PHY_TRSV0_EMP_LVL 0x084 +#define PCIE_PHY_TRSV0_DRV_LVL 0x088 +#define PCIE_PHY_TRSV0_RXCDR 0x0ac +#define PCIE_PHY_TRSV0_LVCC 0x0dc +#define PCIE_PHY_TRSV1_EMP_LVL 0x144 +#define PCIE_PHY_TRSV1_RXCDR 0x16c +#define PCIE_PHY_TRSV1_LVCC 0x19c +#define PCIE_PHY_TRSV2_EMP_LVL 0x204 +#define PCIE_PHY_TRSV2_RXCDR 0x22c +#define PCIE_PHY_TRSV2_LVCC 0x25c +#define PCIE_PHY_TRSV3_EMP_LVL 0x2c4 +#define PCIE_PHY_TRSV3_RXCDR 0x2ec +#define PCIE_PHY_TRSV3_LVCC 0x31c + +static struct hw_pci exynos_pci; + +static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys) +{ + return sys->private_data; +} + +static inline int cfg_read(void *addr, int where, int size, u32 *val) +{ + *val = readl(addr); + + if (size == 1) + *val = (*val >> (8 * (where & 3))) & 0xff; + else if (size == 2) + *val = (*val >> (8 * (where & 3))) & 0xffff; + else if (size != 4) + return PCIBIOS_BAD_REGISTER_NUMBER; + + return PCIBIOS_SUCCESSFUL; +} + +static inline int cfg_write(void *addr, int where, int size, u32 val) +{ + if (size == 4) + writel(val, addr); + else if (size == 2) + writew(val, addr + (where & 2)); + else if (size == 1) + writeb(val, addr + (where & 3)); + else + return PCIBIOS_BAD_REGISTER_NUMBER; + + return PCIBIOS_SUCCESSFUL; +} + +static void exynos_pcie_sideband_dbi_w_mode(struct pcie_port *pp, bool on) +{ + u32 val; + + if (on) { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + val |= PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + } else { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + val &= ~PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + } +} + +static void exynos_pcie_sideband_dbi_r_mode(struct pcie_port *pp, bool on) +{ + u32 val; + + if (on) { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + val |= PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + } else { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + val &= ~PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + } +} + +static inline void readl_rc(struct pcie_port *pp, void *dbi_base, u32 *val) +{ + exynos_pcie_sideband_dbi_r_mode(pp, true); + *val = readl(dbi_base); + exynos_pcie_sideband_dbi_r_mode(pp, false); + return; +} + +static inline void writel_rc(struct pcie_port *pp, u32 val, void *dbi_base) +{ + exynos_pcie_sideband_dbi_w_mode(pp, true); + writel(val, dbi_base); + exynos_pcie_sideband_dbi_w_mode(pp, false); + return; +} + +static int exynos_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, + u32 *val) +{ + int ret; + + exynos_pcie_sideband_dbi_r_mode(pp, true); + ret = cfg_read(pp->dbi_base + (where & ~0x3), where, size, val); + exynos_pcie_sideband_dbi_r_mode(pp, false); + return ret; +} + +static int exynos_pcie_wr_own_conf(struct pcie_port *pp, int where, int size, + u32 val) +{ + int ret; + + exynos_pcie_sideband_dbi_w_mode(pp, true); + ret = cfg_write(pp->dbi_base + (where & ~0x3), where, size, val); + exynos_pcie_sideband_dbi_w_mode(pp, false); + return ret; +} + +static void exynos_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 0 : OUTBOUND : CFG0 */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, (u32)pp->cfg0_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u32)pp->cfg0_base + pp->config.cfg0_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); + writel_rc(pp, PCIE_ATU_TYPE_CFG0, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); +} + +static void exynos_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 1 : OUTBOUND : CFG1 */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_CFG1, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u32)pp->cfg1_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u32)pp->cfg1_base + pp->config.cfg1_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 0 : OUTBOUND : MEM */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u32)pp->mem_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u32)(pp->mem_base + pp->config.mem_size - 1), + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u32)pp->mem_base, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_io_outbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 1 : OUTBOUND : IO */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u32)pp->io_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u32)(pp->io_base + pp->config.io_size - 1), + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u32)pp->io_base, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_mem_inbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + struct pcie_port_info *config = &pp->config; + + /* Program viewport 0 : INBOUND : MEMORY */ + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, config->in_mem_size - 1, dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_io_inbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + struct pcie_port_info *config = &pp->config; + + /* Program viewport 1 : INBOUND : IO */ + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, config->in_mem_size - 1, dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, 0, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static int exynos_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, + u32 devfn, int where, int size, u32 *val) +{ + int ret = PCIBIOS_SUCCESSFUL; + u32 address, busdev; + + busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | + PCIE_ATU_FUNC(PCI_FUNC(devfn)); + address = where & ~0x3; + + if (bus->parent->number == pp->root_bus_nr) { + exynos_pcie_prog_viewport_cfg0(pp, busdev); + ret = cfg_read(pp->va_cfg0_base + address, where, size, val); + exynos_pcie_prog_viewport_mem_outbound(pp); + } else { + exynos_pcie_prog_viewport_cfg1(pp, busdev); + ret = cfg_read(pp->va_cfg1_base + address, where, size, val); + exynos_pcie_prog_viewport_io_outbound(pp); + } + + return ret; +} + +static int exynos_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus, + u32 devfn, int where, int size, u32 val) +{ + int ret = PCIBIOS_SUCCESSFUL; + u32 address, busdev; + + busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | + PCIE_ATU_FUNC(PCI_FUNC(devfn)); + address = where & ~0x3; + + if (bus->parent->number == pp->root_bus_nr) { + exynos_pcie_prog_viewport_cfg0(pp, busdev); + ret = cfg_write(pp->va_cfg0_base + address, where, size, val); + exynos_pcie_prog_viewport_mem_outbound(pp); + } else { + exynos_pcie_prog_viewport_cfg1(pp, busdev); + ret = cfg_write(pp->va_cfg1_base + address, where, size, val); + exynos_pcie_prog_viewport_io_outbound(pp); + } + + return ret; +} + +static int exynos_pcie_setup(int nr, struct pci_sys_data *sys) +{ + struct pcie_port *pp; + + pp = sys_to_pcie(sys); + + if (!pp) + return 0; + + pci_add_resource_offset(&sys->resources, &pp->io, sys->io_offset); + pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset); + + return 1; +} + +static int exynos_pcie_link_up(struct pcie_port *pp) +{ + u32 val = readl(pp->elbi_base + PCIE_ELBI_RDLH_LINKUP); + if (val == PCIE_ELBI_LTSSM_ENABLE) + return 1; + + return 0; +} + +static int exynos_pcie_valid_config(struct pcie_port *pp, + struct pci_bus *bus, int dev) +{ + /* If there is no link, then there is no device */ + if (bus->number != pp->root_bus_nr) { + if (!exynos_pcie_link_up(pp)) + return 0; + } + + /* access only one slot on each root port */ + if (bus->number == pp->root_bus_nr && dev > 0) + return 0; + + /* + * do not read more than one device on the bus directly attached + * to RC's (Virtual Bridge's) DS side. + */ + if (bus->primary == pp->root_bus_nr && dev > 0) + return 0; + + return 1; +} + +static int exynos_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, + int size, u32 *val) +{ + struct pcie_port *pp = sys_to_pcie(bus->sysdata); + unsigned long flags; + int ret; + + if (!pp) { + BUG(); + return -EINVAL; + } + + if (exynos_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) { + *val = 0xffffffff; + return PCIBIOS_DEVICE_NOT_FOUND; + } + + spin_lock_irqsave(&pp->conf_lock, flags); + if (bus->number != pp->root_bus_nr) + ret = exynos_pcie_rd_other_conf(pp, bus, devfn, + where, size, val); + else + ret = exynos_pcie_rd_own_conf(pp, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static int exynos_pcie_wr_conf(struct pci_bus *bus, u32 devfn, + int where, int size, u32 val) +{ + struct pcie_port *pp = sys_to_pcie(bus->sysdata); + unsigned long flags; + int ret; + + if (!pp) { + BUG(); + return -EINVAL; + } + + if (exynos_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + spin_lock_irqsave(&pp->conf_lock, flags); + if (bus->number != pp->root_bus_nr) + ret = exynos_pcie_wr_other_conf(pp, bus, devfn, + where, size, val); + else + ret = exynos_pcie_wr_own_conf(pp, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static struct pci_ops exynos_pcie_ops = { + .read = exynos_pcie_rd_conf, + .write = exynos_pcie_wr_conf, +}; + +static struct pci_bus *exynos_pcie_scan_bus(int nr, + struct pci_sys_data *sys) +{ + struct pci_bus *bus; + struct pcie_port *pp = sys_to_pcie(sys); + + if (pp) { + pp->root_bus_nr = sys->busnr; + bus = pci_scan_root_bus(NULL, sys->busnr, &exynos_pcie_ops, + sys, &sys->resources); + return bus; + } else { + bus = NULL; + BUG(); + } + + return bus; +} + +static int exynos_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata); + + return pp->irq; +} + +static struct hw_pci exynos_pci = { + .setup = exynos_pcie_setup, + .scan = exynos_pcie_scan_bus, + .map_irq = exynos_pcie_map_irq, +}; + +static void exynos_pcie_setup_rc(struct pcie_port *pp) +{ + struct pcie_port_info *config = &pp->config; + void __iomem *dbi_base = pp->dbi_base; + u32 val; + u32 membase; + u32 memlimit; + + /* set the number of lines as 4 */ + readl_rc(pp, dbi_base + PCIE_PORT_LINK_CONTROL, &val); + val &= ~PORT_LINK_MODE_MASK; + val |= PORT_LINK_MODE_4_LANES; + writel_rc(pp, val, dbi_base + PCIE_PORT_LINK_CONTROL); + + /* set link width speed control register */ + readl_rc(pp, dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL, &val); + val &= ~PORT_LOGIC_LINK_WIDTH_MASK; + val |= PORT_LOGIC_LINK_WIDTH_4_LANES; + writel_rc(pp, val, dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL); + + /* setup RC BARs */ + writel_rc(pp, 0x00000004, dbi_base + PCI_BASE_ADDRESS_0); + writel_rc(pp, 0x00000004, dbi_base + PCI_BASE_ADDRESS_1); + + /* setup interrupt pins */ + readl_rc(pp, dbi_base + PCI_INTERRUPT_LINE, &val); + val &= 0xffff00ff; + val |= 0x00000100; + writel_rc(pp, val, dbi_base + PCI_INTERRUPT_LINE); + + /* setup bus numbers */ + readl_rc(pp, dbi_base + PCI_PRIMARY_BUS, &val); + val &= 0xff000000; + val |= 0x00010100; + writel_rc(pp, val, dbi_base + PCI_PRIMARY_BUS); + + /* setup memory base, memory limit */ + membase = ((u32)pp->mem_base & 0xfff00000) >> 16; + memlimit = (config->mem_size + (u32)pp->mem_base) & 0xfff00000; + val = memlimit | membase; + writel_rc(pp, val, dbi_base + PCI_MEMORY_BASE); + + /* setup command register */ + readl_rc(pp, dbi_base + PCI_COMMAND, &val); + val &= 0xffff0000; + val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY | + PCI_COMMAND_MASTER | PCI_COMMAND_SERR; + writel_rc(pp, val, dbi_base + PCI_COMMAND); +} + +static void exynos_pcie_assert_core_reset(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + val = readl(elbi_base + PCIE_CORE_RESET); + val &= ~PCIE_CORE_RESET_ENABLE; + writel(val, elbi_base + PCIE_CORE_RESET); + writel(0, elbi_base + PCIE_PWR_RESET); + writel(0, elbi_base + PCIE_STICKY_RESET); + writel(0, elbi_base + PCIE_NONSTICKY_RESET); +} + +static void exynos_pcie_deassert_core_reset(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + + val = readl(elbi_base + PCIE_CORE_RESET); + val |= PCIE_CORE_RESET_ENABLE; + writel(val, elbi_base + PCIE_CORE_RESET); + writel(1, elbi_base + PCIE_STICKY_RESET); + writel(1, elbi_base + PCIE_NONSTICKY_RESET); + writel(1, elbi_base + PCIE_APP_INIT_RESET); + writel(0, elbi_base + PCIE_APP_INIT_RESET); + writel(1, purple_base + PCIE_PHY_MAC_RESET); +} + +static void exynos_pcie_assert_phy_reset(struct pcie_port *pp) +{ + void __iomem *purple_base = pp->purple_base; + + writel(0, purple_base + PCIE_PHY_MAC_RESET); + writel(1, purple_base + PCIE_PHY_GLOBAL_RESET); +} + +static void exynos_pcie_deassert_phy_reset(struct pcie_port *pp) +{ + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + + writel(0, purple_base + PCIE_PHY_GLOBAL_RESET); + writel(1, elbi_base + PCIE_PWR_RESET); + writel(0, purple_base + PCIE_PHY_COMMON_RESET); + writel(0, purple_base + PCIE_PHY_CMN_REG); + writel(0, purple_base + PCIE_PHY_TRSVREG_RESET); + writel(0, purple_base + PCIE_PHY_TRSV_RESET); +} + +static void exynos_pcie_init_phy(struct pcie_port *pp) +{ + void __iomem *phy_base = pp->phy_base; + + /* DCC feedback control off */ + writel(0x29, phy_base + PCIE_PHY_DCC_FEEDBACK); + + /* set TX/RX impedance */ + writel(0xd5, phy_base + PCIE_PHY_IMPEDANCE); + + /* set 50Mhz PHY clock */ + writel(0x14, phy_base + PCIE_PHY_PLL_DIV_0); + writel(0x12, phy_base + PCIE_PHY_PLL_DIV_1); + + /* set TX Differential output for lane 0 */ + writel(0x7f, phy_base + PCIE_PHY_TRSV0_DRV_LVL); + + /* set TX Pre-emphasis Level Control for lane 0 to minimum */ + writel(0x0, phy_base + PCIE_PHY_TRSV0_EMP_LVL); + + /* set RX clock and data recovery bandwidth */ + writel(0xe7, phy_base + PCIE_PHY_PLL_BIAS); + writel(0x82, phy_base + PCIE_PHY_TRSV0_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV1_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV2_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV3_RXCDR); + + /* change TX Pre-emphasis Level Control for lanes */ + writel(0x39, phy_base + PCIE_PHY_TRSV0_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV1_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV2_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV3_EMP_LVL); + + /* set LVCC */ + writel(0x20, phy_base + PCIE_PHY_TRSV0_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV1_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV2_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV3_LVCC); +} + +static void exynos_pcie_assert_reset(struct pcie_port *pp) +{ + if (pp->reset_gpio >= 0) + devm_gpio_request_one(pp->dev, pp->reset_gpio, + GPIOF_OUT_INIT_HIGH, "RESET"); + return; +} + +static int exynos_pcie_establish_link(struct pcie_port *pp) +{ + u32 val; + int count = 0; + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + void __iomem *phy_base = pp->phy_base; + + if (exynos_pcie_link_up(pp)) { + dev_err(pp->dev, "Link already up\n"); + return 0; + } + + /* assert reset signals */ + exynos_pcie_assert_core_reset(pp); + exynos_pcie_assert_phy_reset(pp); + + /* de-assert phy reset */ + exynos_pcie_deassert_phy_reset(pp); + + /* initialize phy */ + exynos_pcie_init_phy(pp); + + /* pulse for common reset */ + writel(1, purple_base + PCIE_PHY_COMMON_RESET); + udelay(500); + writel(0, purple_base + PCIE_PHY_COMMON_RESET); + + /* de-assert core reset */ + exynos_pcie_deassert_core_reset(pp); + + /* setup root complex */ + exynos_pcie_setup_rc(pp); + + /* assert reset signal */ + exynos_pcie_assert_reset(pp); + + /* assert LTSSM enable */ + writel(PCIE_ELBI_LTSSM_ENABLE, elbi_base + PCIE_APP_LTSSM_ENABLE); + + /* check if the link is up or not */ + while (!exynos_pcie_link_up(pp)) { + mdelay(100); + count++; + if (count == 10) { + while (readl(phy_base + PCIE_PHY_PLL_LOCKED) == 0) { + val = readl(purple_base + PCIE_PHY_PLL_LOCKED); + dev_info(pp->dev, "PLL Locked: 0x%x\n", val); + } + dev_err(pp->dev, "PCIe Link Fail\n"); + return -EINVAL; + } + } + + dev_info(pp->dev, "Link up\n"); + + return 0; +} + +static void exynos_pcie_clear_irq_pulse(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + val = readl(elbi_base + PCIE_IRQ_PULSE); + writel(val, elbi_base + PCIE_IRQ_PULSE); + return; +} + +static void exynos_pcie_enable_irq_pulse(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + /* enable INTX interrupt */ + val = IRQ_INTA_ASSERT | IRQ_INTB_ASSERT | + IRQ_INTC_ASSERT | IRQ_INTD_ASSERT, + writel(val, elbi_base + PCIE_IRQ_EN_PULSE); + return; +} + +static irqreturn_t exynos_pcie_irq_handler(int irq, void *arg) +{ + struct pcie_port *pp = arg; + + exynos_pcie_clear_irq_pulse(pp); + return IRQ_HANDLED; +} + +static void exynos_pcie_enable_interrupts(struct pcie_port *pp) +{ + exynos_pcie_enable_irq_pulse(pp); + return; +} + +static void exynos_pcie_host_init(struct pcie_port *pp) +{ + struct pcie_port_info *config = &pp->config; + u32 val; + + /* Keep first 64K for IO */ + pp->cfg0_base = pp->cfg.start; + pp->cfg1_base = pp->cfg0_base + config->cfg0_size; + pp->io_base = pp->cfg1_base + config->cfg1_size; + pp->mem_base = pp->io_base + config->io_size; + + /* enable link */ + exynos_pcie_establish_link(pp); + + /* set view ports for inbound */ + exynos_pcie_prog_viewport_mem_inbound(pp); + exynos_pcie_prog_viewport_io_inbound(pp); + + exynos_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0); + + /* program correct class for RC */ + exynos_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI); + + exynos_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val); + val |= PORT_LOGIC_SPEED_CHANGE; + exynos_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val); + + exynos_pcie_enable_interrupts(pp); +} + +static int add_pcie_port(struct pcie_port *pp, struct platform_device *pdev) +{ + struct resource *elbi_base; + struct resource *phy_base; + struct resource *purple_base; + int ret; + + elbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!elbi_base) { + dev_err(&pdev->dev, "couldn't get elbi base resource\n"); + return -EINVAL; + } + pp->elbi_base = devm_ioremap_resource(&pdev->dev, elbi_base); + if (IS_ERR(pp->elbi_base)) + return PTR_ERR(pp->elbi_base); + + phy_base = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!phy_base) { + dev_err(&pdev->dev, "couldn't get phy base resource\n"); + return -EINVAL; + } + pp->phy_base = devm_ioremap_resource(&pdev->dev, phy_base); + if (IS_ERR(pp->phy_base)) + return PTR_ERR(pp->phy_base); + + purple_base = platform_get_resource(pdev, IORESOURCE_MEM, 2); + if (!purple_base) { + dev_err(&pdev->dev, "couldn't get purple base resource\n"); + return -EINVAL; + } + pp->purple_base = devm_ioremap_resource(&pdev->dev, purple_base); + if (IS_ERR(pp->purple_base)) + return PTR_ERR(pp->purple_base); + + pp->irq = platform_get_irq(pdev, 1); + if (!pp->irq) { + dev_err(&pdev->dev, "failed to get irq\n"); + return -ENODEV; + } + ret = devm_request_irq(&pdev->dev, pp->irq, exynos_pcie_irq_handler, + IRQF_SHARED, "exynos-pcie", pp); + if (ret) { + dev_err(&pdev->dev, "failed to request irq\n"); + return ret; + } + + pp->dbi_base = devm_ioremap(&pdev->dev, pp->cfg.start, + resource_size(&pp->cfg)); + if (!pp->dbi_base) { + dev_err(&pdev->dev, "error with ioremap\n"); + return -ENOMEM; + } + + pp->root_bus_nr = -1; + + spin_lock_init(&pp->conf_lock); + exynos_pcie_host_init(pp); + pp->va_cfg0_base = devm_ioremap(&pdev->dev, pp->cfg0_base, + pp->config.cfg0_size); + if (!pp->va_cfg0_base) { + dev_err(pp->dev, "error with ioremap in function\n"); + return -ENOMEM; + } + pp->va_cfg1_base = devm_ioremap(&pdev->dev, pp->cfg1_base, + pp->config.cfg1_size); + if (!pp->va_cfg1_base) { + dev_err(pp->dev, "error with ioremap\n"); + return -ENOMEM; + } + + return 0; +} + +static int __init exynos_pcie_probe(struct platform_device *pdev) +{ + struct pcie_port *pp; + struct device_node *np = pdev->dev.of_node; + struct of_pci_range range; + struct of_pci_range_parser parser; + int ret; + + pp = devm_kzalloc(&pdev->dev, sizeof(*pp), GFP_KERNEL); + if (!pp) { + dev_err(&pdev->dev, "no memory for pcie port\n"); + return -ENOMEM; + } + + pp->dev = &pdev->dev; + + if (of_pci_range_parser_init(&parser, np)) { + dev_err(&pdev->dev, "missing ranges property\n"); + return -EINVAL; + } + + /* Get the I/O and memory ranges from DT */ + for_each_of_pci_range(&parser, &range) { + unsigned long restype = range.flags & IORESOURCE_TYPE_BITS; + if (restype == IORESOURCE_IO) { + of_pci_range_to_resource(&range, np, &pp->io); + pp->io.name = "I/O"; + pp->config.io_size = resource_size(&pp->io); + } + if (restype == IORESOURCE_MEM) { + of_pci_range_to_resource(&range, np, &pp->mem); + pp->mem.name = "MEM"; + pp->config.mem_size = resource_size(&pp->mem); + } + if (restype == 0) { + of_pci_range_to_resource(&range, np, &pp->cfg); + pp->config.cfg0_size = resource_size(&pp->cfg)/2; + pp->config.cfg1_size = resource_size(&pp->cfg)/2; + } + } + + pp->config.in_mem_size = SZ_256M; + + ret = of_property_read_u32(np, "reset-gpio", &pp->reset_gpio); + if (ret < 0) + pp->reset_gpio = -1; + + pp->clk = devm_clk_get(&pdev->dev, "pcie"); + if (IS_ERR(pp->clk)) { + dev_err(&pdev->dev, "Failed to get pcie rc clock\n"); + return PTR_ERR(pp->clk); + } + ret = clk_prepare_enable(pp->clk); + if (ret) + return ret; + + pp->bus_clk = devm_clk_get(&pdev->dev, "pcie_bus"); + if (IS_ERR(pp->bus_clk)) { + dev_err(&pdev->dev, "Failed to get pcie bus clock\n"); + ret = PTR_ERR(pp->bus_clk); + goto fail_clk; + } + ret = clk_prepare_enable(pp->bus_clk); + if (ret) + goto fail_clk; + + ret = add_pcie_port(pp, pdev); + if (ret < 0) + goto fail_bus_clk; + + pp->controller = exynos_pci.nr_controllers; + exynos_pci.nr_controllers = 1; + exynos_pci.private_data = (void **)&pp; + + pci_common_init(&exynos_pci); + pci_assign_unassigned_resources(); +#ifdef CONFIG_PCI_DOMAINS + exynos_pci.domain++; +#endif + + platform_set_drvdata(pdev, pp); + return 0; + +fail_bus_clk: + clk_disable_unprepare(pp->bus_clk); +fail_clk: + clk_disable_unprepare(pp->clk); + return ret; +} + +static int __exit exynos_pcie_remove(struct platform_device *pdev) +{ + struct pcie_port *pp = platform_get_drvdata(pdev); + + clk_disable_unprepare(pp->bus_clk); + clk_disable_unprepare(pp->clk); + + return 0; +} + +static const struct of_device_id exynos_pcie_of_match[] = { + { .compatible = "samsung,exynos5440-pcie", }, + {}, +}; +MODULE_DEVICE_TABLE(of, exynos_pcie_of_match); + +static struct platform_driver exynos_pcie_driver = { + .remove = __exit_p(exynos_pcie_remove), + .driver = { + .name = "exynos-pcie", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(exynos_pcie_of_match), + }, +}; + +static int exynos_pcie_abort(unsigned long addr, unsigned int fsr, + struct pt_regs *regs) +{ + unsigned long pc = instruction_pointer(regs); + unsigned long instr = *(unsigned long *)pc; + + WARN_ONCE(1, "pcie abort\n"); + + /* + * If the instruction being executed was a read, + * make it look like it read all-ones. + */ + if ((instr & 0x0c100000) == 0x04100000) { + int reg = (instr >> 12) & 15; + unsigned long val; + + if (instr & 0x00400000) + val = 255; + else + val = -1; + + regs->uregs[reg] = val; + regs->ARM_pc += 4; + return 0; + } + + if ((instr & 0x0e100090) == 0x00100090) { + int reg = (instr >> 12) & 15; + + regs->uregs[reg] = -1; + regs->ARM_pc += 4; + return 0; + } + + return 1; +} + +static int __init pcie_init(void) +{ + hook_fault_code(16 + 6, exynos_pcie_abort, SIGBUS, 0, + "imprecise external abort"); + + platform_driver_probe(&exynos_pcie_driver, exynos_pcie_probe); + + return 0; +} +subsys_initcall(pcie_init); + +static void __exit pcie_exit(void) +{ + platform_driver_unregister(&exynos_pcie_driver); +} +module_exit(pcie_exit); + +MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>"); +MODULE_DESCRIPTION("Samsung PCIe host controller driver"); +MODULE_LICENSE("GPLv2");

[V4,1/3] pci: Add PCIe driver for Samsung Exynos

Commit Message

Comments

Patch