@@ -381,16 +381,11 @@ static int ath10k_sdio_mbox_rx_process_packet(struct ath10k *ar,
struct ath10k_htc_hdr *htc_hdr = (struct ath10k_htc_hdr *)skb->data;
bool trailer_present = htc_hdr->flags & ATH10K_HTC_FLAG_TRAILER_PRESENT;
enum ath10k_htc_ep_id eid;
- u16 payload_len;
u8 *trailer;
int ret;
- payload_len = le16_to_cpu(htc_hdr->len);
- skb->len = payload_len + sizeof(struct ath10k_htc_hdr);
-
if (trailer_present) {
- trailer = skb->data + sizeof(*htc_hdr) +
- payload_len - htc_hdr->trailer_len;
+ trailer = skb->data + skb->len - htc_hdr->trailer_len;
eid = pipe_id_to_eid(htc_hdr->eid);
@@ -636,9 +631,23 @@ static int ath10k_sdio_mbox_rx_packet(struct ath10k *ar,
ret = ath10k_sdio_readsb(ar, ar_sdio->mbox_info.htc_addr,
skb->data, pkt->alloc_len);
+ if (!ret) {
+ /* Update actual length. The original length may be incorrect,
+ * as the FW will bundle multiple packets as long as their sizes
+ * fit within the same aligned length (pkt->alloc_len).
+ */
+ struct ath10k_htc_hdr *htc_hdr =
+ (struct ath10k_htc_hdr *)skb->data;
+ pkt->act_len = le16_to_cpu(htc_hdr->len) + sizeof(*htc_hdr);
+ if (pkt->act_len <= pkt->alloc_len) {
+ skb_put(skb, pkt->act_len);
+ } else {
+ ath10k_warn(ar, "rx_packet too large (%d > %d)\n",
+ pkt->act_len, pkt->alloc_len);
+ ret = -EMSGSIZE;
+ }
+ }
pkt->status = ret;
- if (!ret)
- skb_put(skb, pkt->act_len);
return ret;
}
When the FW bundles multiple packets, pkt->act_len may be incorrect as it refers to the first packet only (however, the FW will only bundle packets that fit into the same pkt->alloc_len). Before this patch, the skb length would be set (incorrectly) to pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually adjusted in ath10k_sdio_mbox_rx_process_packet. The first problem is that ath10k_sdio_mbox_rx_process_packet does not use proper skb_put commands to adjust the length (it directly changes skb->len), so we end up with a mismatch between skb->head + skb->tail and skb->data + skb->len. This is quite serious, and causes corruptions in the TCP stack, as the stack tries to coalesce packets, and relies on skb->tail being correct (that is, skb_tail_pointer must point to the first byte_after_ the data). Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet, this moves the code to ath10k_sdio_mbox_rx_packet, and also add a bounds check, as skb_put would crash the kernel if not enough space is available. Fixes: 8530b4e7b22bc3b ("ath10k: sdio: set skb len for all rx packets") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> --- One simple way to reproduce this issue is this scriplet, that sends a lot of small packets over SSH (it usually fails before reaching 300): (for i in `seq 1 300`; do echo $i; sleep 0.1; done) | ssh $IP cat I was not able to check the original use case why the code was added (packets > 1500 bytes), as the FW on my board crashes when sending such large packets. drivers/net/wireless/ath/ath10k/sdio.c | 25 +++++++++++++++++-------- 1 file changed, 17 insertions(+), 8 deletions(-)