@@ -158,6 +158,9 @@ enum htt_rx_ring_flags {
HTT_RX_RING_FLAGS_PHY_DATA_RX = 1 << 15
};
+#define HTT_RX_RING_SIZE_MIN 128
+#define HTT_RX_RING_SIZE_MAX 2048
+
struct htt_rx_ring_setup_ring {
__le32 fw_idx_shadow_reg_paddr;
__le32 rx_ring_base_paddr;
@@ -25,19 +25,8 @@
#include <linux/log2.h>
-/* slightly larger than one large A-MPDU */
-#define HTT_RX_RING_SIZE_MIN 128
-
-/* roughly 20 ms @ 1 Gbps of 1500B MSDUs */
-#define HTT_RX_RING_SIZE_MAX 2048
-
-#define HTT_RX_AVG_FRM_BYTES 1000
-
-/* ms, very conservative */
-#define HTT_RX_HOST_LATENCY_MAX_MS 20
-
-/* ms, conservative */
-#define HTT_RX_HOST_LATENCY_WORST_LIKELY_MS 10
+#define HTT_RX_RING_SIZE 1024
+#define HTT_RX_RING_FILL_LEVEL 1000
/* when under memory pressure rx ring refill may fail and needs a retry */
#define HTT_RX_RING_REFILL_RETRY_MS 50
@@ -45,68 +34,6 @@
static int ath10k_htt_rx_get_csum_state(struct sk_buff *skb);
static void ath10k_htt_txrx_compl_task(unsigned long ptr);
-static int ath10k_htt_rx_ring_size(struct ath10k_htt *htt)
-{
- int size;
-
- /*
- * It is expected that the host CPU will typically be able to
- * service the rx indication from one A-MPDU before the rx
- * indication from the subsequent A-MPDU happens, roughly 1-2 ms
- * later. However, the rx ring should be sized very conservatively,
- * to accomodate the worst reasonable delay before the host CPU
- * services a rx indication interrupt.
- *
- * The rx ring need not be kept full of empty buffers. In theory,
- * the htt host SW can dynamically track the low-water mark in the
- * rx ring, and dynamically adjust the level to which the rx ring
- * is filled with empty buffers, to dynamically meet the desired
- * low-water mark.
- *
- * In contrast, it's difficult to resize the rx ring itself, once
- * it's in use. Thus, the ring itself should be sized very
- * conservatively, while the degree to which the ring is filled
- * with empty buffers should be sized moderately conservatively.
- */
-
- /* 1e6 bps/mbps / 1e3 ms per sec = 1000 */
- size =
- htt->max_throughput_mbps +
- 1000 /
- (8 * HTT_RX_AVG_FRM_BYTES) * HTT_RX_HOST_LATENCY_MAX_MS;
-
- if (size < HTT_RX_RING_SIZE_MIN)
- size = HTT_RX_RING_SIZE_MIN;
-
- if (size > HTT_RX_RING_SIZE_MAX)
- size = HTT_RX_RING_SIZE_MAX;
-
- size = roundup_pow_of_two(size);
-
- return size;
-}
-
-static int ath10k_htt_rx_ring_fill_level(struct ath10k_htt *htt)
-{
- int size;
-
- /* 1e6 bps/mbps / 1e3 ms per sec = 1000 */
- size =
- htt->max_throughput_mbps *
- 1000 /
- (8 * HTT_RX_AVG_FRM_BYTES) * HTT_RX_HOST_LATENCY_WORST_LIKELY_MS;
-
- /*
- * Make sure the fill level is at least 1 less than the ring size.
- * Leaving 1 element empty allows the SW to easily distinguish
- * between a full ring vs. an empty ring.
- */
- if (size >= htt->rx_ring.size)
- size = htt->rx_ring.size - 1;
-
- return size;
-}
-
static void ath10k_htt_rx_ring_free(struct ath10k_htt *htt)
{
struct sk_buff *skb;
@@ -462,25 +389,18 @@ int ath10k_htt_rx_alloc(struct ath10k_htt *htt)
htt->rx_confused = false;
- htt->rx_ring.size = ath10k_htt_rx_ring_size(htt);
+ /* XXX: The fill level could be changed during runtime in response to
+ * the host processing latency. Is this really worth it?
+ */
+ htt->rx_ring.size = HTT_RX_RING_SIZE;
+ htt->rx_ring.size_mask = htt->rx_ring.size - 1;
+ htt->rx_ring.fill_level = HTT_RX_RING_FILL_LEVEL;
+
if (!is_power_of_2(htt->rx_ring.size)) {
ath10k_warn(ar, "htt rx ring size is not power of 2\n");
return -EINVAL;
}
- htt->rx_ring.size_mask = htt->rx_ring.size - 1;
-
- /*
- * Set the initial value for the level to which the rx ring
- * should be filled, based on the max throughput and the
- * worst likely latency for the host to fill the rx ring
- * with new buffers. In theory, this fill level can be
- * dynamically adjusted from the initial value set here, to
- * reflect the actual host latency rather than a
- * conservative assumption about the host latency.
- */
- htt->rx_ring.fill_level = ath10k_htt_rx_ring_fill_level(htt);
-
htt->rx_ring.netbufs_ring =
kzalloc(htt->rx_ring.size * sizeof(struct sk_buff *),
GFP_KERNEL);
Don't bother with fancy arithmetic and just hardcode the final values. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> --- drivers/net/wireless/ath/ath10k/htt.h | 3 + drivers/net/wireless/ath/ath10k/htt_rx.c | 98 +++----------------------------- 2 files changed, 12 insertions(+), 89 deletions(-)