diff mbox

ath10k: fix boot failure in UTF mode/testmode

Message ID 1485525098-11548-1-git-send-email-c_traja@qti.qualcomm.com (mailing list archive)
State Superseded
Delegated to: Kalle Valo
Headers show

Commit Message

c_traja@qti.qualcomm.com Jan. 27, 2017, 1:51 p.m. UTC
From: Tamizh chelvam <c_traja@qti.qualcomm.com>

Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.

Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110

Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95

Avoiding these configurations while bringing the target in
testmode is solving the problem.

Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
diff mbox

Patch

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 874c2a7..0d12761 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -1922,7 +1922,8 @@  int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
 	ath10k_dbg(ar, ATH10K_DBG_BOOT, "firmware %s booted\n",
 		   ar->hw->wiphy->fw_version);
 
-	if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map) &&
+	    mode == ATH10K_FIRMWARE_MODE_NORMAL) {
 		val = 0;
 		if (ath10k_peer_stats_enabled(ar))
 			val = WMI_10_4_PEER_STATS;
@@ -1975,10 +1976,13 @@  int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
 	 * possible to implicitly make it correct by creating a dummy vdev and
 	 * then deleting it.
 	 */
-	status = ath10k_core_reset_rx_filter(ar);
-	if (status) {
-		ath10k_err(ar, "failed to reset rx filter: %d\n", status);
-		goto err_hif_stop;
+	if (mode == ATH10K_FIRMWARE_MODE_NORMAL) {
+		status = ath10k_core_reset_rx_filter(ar);
+		if (status) {
+			ath10k_err(ar,
+				   "failed to reset rx filter: %d\n", status);
+			goto err_hif_stop;
+		}
 	}
 
 	/* If firmware indicates Full Rx Reorder support it must be used in a