diff mbox series

[1/2] dt-bindings: ath10k: Add new dt entries to identify coex support

Message ID 1576496415-23064-1-git-send-email-tamizhr@codeaurora.org (mailing list archive)
State New, archived
Headers show
Series [1/2] dt-bindings: ath10k: Add new dt entries to identify coex support | expand

Commit Message

Tamizh chelvam Dec. 16, 2019, 11:40 a.m. UTC
This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin
which will be used by ath10k driver to identify coex support
of a hardware and notify wifi firmware the gpio pin number.
This pin number information is needed for the hardware QCA4019.

Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
---
 Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 ++++++
 1 file changed, 6 insertions(+)

Comments

Rob Herring (Arm) Dec. 26, 2019, 6:51 p.m. UTC | #1
On Mon, Dec 16, 2019 at 05:10:14PM +0530, Tamizh Chelvam wrote:
> This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin
> which will be used by ath10k driver to identify coex support
> of a hardware and notify wifi firmware the gpio pin number.
> This pin number information is needed for the hardware QCA4019.
> 
> Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> index 0171283..a41e936 100644
> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> @@ -87,6 +87,10 @@ Optional properties:
>  	Definition: Quirk specifying that the firmware expects the 8bit version
>  		    of the host capability QMI request
>  - qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
> +- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex
> +			 support by the hardware.
> +- qcom,coexist-gpio-pin : gpio pin number  information to support coex
> +			  which will be used by wifi firmware.

What combinations of these 2 properties are valid?

Is qcom,coexist-gpio-pin required for coexist support? If so then it 
alone should be enough to enable/disable coexist.

>  
>  Example (to supply PCI based wifi block details):
>  
> @@ -156,6 +160,8 @@ wifi0: wifi@a000000 {
>  	qcom,msi_addr = <0x0b006040>;
>  	qcom,msi_base = <0x40>;
>  	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
> +	qcom,coexist-support = <1>;
> +	qcom,coexist-gpio-pin = <0x33>;
>  };
>  
>  Example (to supply wcn3990 SoC wifi block details):
> -- 
> 1.9.1
Tamizh chelvam Dec. 30, 2019, 5:07 a.m. UTC | #2
Hi Rob,

Thanks for your review comments.

>> This adds new dt entries qcom,coexist-support and 
>> qcom,coexist-gpio-pin
>> which will be used by ath10k driver to identify coex support
>> of a hardware and notify wifi firmware the gpio pin number.
>> This pin number information is needed for the hardware QCA4019.
>> 
>> Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
>> ---
>>  Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 
>> ++++++
>>  1 file changed, 6 insertions(+)
>> 
>> diff --git 
>> a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt 
>> b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
>> index 0171283..a41e936 100644
>> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
>> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
>> @@ -87,6 +87,10 @@ Optional properties:
>>  	Definition: Quirk specifying that the firmware expects the 8bit 
>> version
>>  		    of the host capability QMI request
>>  - qcom,xo-cal-data: xo cal offset to be configured in xo trim 
>> register.
>> +- qcom,coexist-support : should contain eithr "0" or "1" to indicate 
>> coex
>> +			 support by the hardware.
>> +- qcom,coexist-gpio-pin : gpio pin number  information to support 
>> coex
>> +			  which will be used by wifi firmware.
> 
> What combinations of these 2 properties are valid?
> 
> Is qcom,coexist-gpio-pin required for coexist support? If so then it
> alone should be enough to enable/disable coexist.
> 
qcom,coexist-gpio-pin is required for QCA4019 devices. And other ath10k 
devices doesn't required that value.
So only added two fields to enable/disable coexist and another for 
notifying the gpio pin info.
>> 
>>  Example (to supply PCI based wifi block details):
>> 
>> @@ -156,6 +160,8 @@ wifi0: wifi@a000000 {
>>  	qcom,msi_addr = <0x0b006040>;
>>  	qcom,msi_base = <0x40>;
>>  	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
>> +	qcom,coexist-support = <1>;
>> +	qcom,coexist-gpio-pin = <0x33>;
>>  };
>> 
>>  Example (to supply wcn3990 SoC wifi block details):
>> --

Thanks,
Tamizh.
Rob Herring (Arm) Dec. 30, 2019, 6:02 p.m. UTC | #3
On Sun, Dec 29, 2019 at 10:07 PM <tamizhr@codeaurora.org> wrote:
>
> Hi Rob,
>
> Thanks for your review comments.
>
> >> This adds new dt entries qcom,coexist-support and
> >> qcom,coexist-gpio-pin
> >> which will be used by ath10k driver to identify coex support
> >> of a hardware and notify wifi firmware the gpio pin number.
> >> This pin number information is needed for the hardware QCA4019.
> >>
> >> Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
> >> ---
> >>  Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6
> >> ++++++
> >>  1 file changed, 6 insertions(+)
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> index 0171283..a41e936 100644
> >> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> @@ -87,6 +87,10 @@ Optional properties:
> >>      Definition: Quirk specifying that the firmware expects the 8bit
> >> version
> >>                  of the host capability QMI request
> >>  - qcom,xo-cal-data: xo cal offset to be configured in xo trim
> >> register.
> >> +- qcom,coexist-support : should contain eithr "0" or "1" to indicate

typo

> >> coex
> >> +                     support by the hardware.
> >> +- qcom,coexist-gpio-pin : gpio pin number  information to support
> >> coex
> >> +                      which will be used by wifi firmware.
> >
> > What combinations of these 2 properties are valid?
> >
> > Is qcom,coexist-gpio-pin required for coexist support? If so then it
> > alone should be enough to enable/disable coexist.
> >
> qcom,coexist-gpio-pin is required for QCA4019 devices. And other ath10k
> devices doesn't required that value.
> So only added two fields to enable/disable coexist and another for
> notifying the gpio pin info.

Okay.

'qcom,coexist-support' can be boolean instead. Unless you need it to
override a default setting.

Rob
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
index 0171283..a41e936 100644
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
@@ -87,6 +87,10 @@  Optional properties:
 	Definition: Quirk specifying that the firmware expects the 8bit version
 		    of the host capability QMI request
 - qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
+- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex
+			 support by the hardware.
+- qcom,coexist-gpio-pin : gpio pin number  information to support coex
+			  which will be used by wifi firmware.
 
 Example (to supply PCI based wifi block details):
 
@@ -156,6 +160,8 @@  wifi0: wifi@a000000 {
 	qcom,msi_addr = <0x0b006040>;
 	qcom,msi_base = <0x40>;
 	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
+	qcom,coexist-support = <1>;
+	qcom,coexist-gpio-pin = <0x33>;
 };
 
 Example (to supply wcn3990 SoC wifi block details):