diff mbox series

[RFC,v2,10/14] drivers: pinctrl: msm: setup GPIO chip in hierarchy

Message ID 1568411962-1022-11-git-send-email-ilina@codeaurora.org (mailing list archive)
State Superseded
Headers show
Series Support wakeup capable GPIOs | expand

Commit Message

Lina Iyer Sept. 13, 2019, 9:59 p.m. UTC
Some GPIOs are marked as wakeup capable and are routed to another
interrupt controller that is an always-domain and can detect interrupts
even most of the SoC is powered off. The wakeup interrupt controller
wakes up the GIC and replays the interrupt at the GIC.

Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
and ensure the wakeup GPIOs are handled correctly.

Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
----
Changes in RFC v2:
	- Define irq_domain_qcom_handle_wakeup()
	- Rebase on top of GPIO hierarchy support in linux-next
	- Set the chained irq handler for summary line
---
 drivers/pinctrl/qcom/pinctrl-msm.c | 119 +++++++++++++++++++++++++++++++++++++
 drivers/pinctrl/qcom/pinctrl-msm.h |  16 +++++
 include/linux/soc/qcom/irq.h       |  13 ++++
 3 files changed, 148 insertions(+)

Comments

Linus Walleij Oct. 3, 2019, 12:17 p.m. UTC | #1
On Fri, Sep 13, 2019 at 11:59 PM Lina Iyer <ilina@codeaurora.org> wrote:

> Some GPIOs are marked as wakeup capable and are routed to another
> interrupt controller that is an always-domain and can detect interrupts
> even most of the SoC is powered off. The wakeup interrupt controller
> wakes up the GIC and replays the interrupt at the GIC.
>
> Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
> and ensure the wakeup GPIOs are handled correctly.
>
> Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
> Signed-off-by: Lina Iyer <ilina@codeaurora.org>
> ----
> Changes in RFC v2:
>         - Define irq_domain_qcom_handle_wakeup()
>         - Rebase on top of GPIO hierarchy support in linux-next
>         - Set the chained irq handler for summary line

This is looking better every time I look at it, it's really complex
but alas the problem is hard to solve so it requires complex solutions.

> @@ -1006,6 +1091,7 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
>         struct gpio_irq_chip *girq;
>         int ret;
>         unsigned ngpio = pctrl->soc->ngpios;
> +       struct device_node *dn;

I usually call the variable "np"

> @@ -1021,17 +1107,40 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
>
>         pctrl->irq_chip.name = "msmgpio";
>         pctrl->irq_chip.irq_enable = msm_gpio_irq_enable;
> +       pctrl->irq_chip.irq_disable = msm_gpio_irq_disable;
>         pctrl->irq_chip.irq_mask = msm_gpio_irq_mask;
>         pctrl->irq_chip.irq_unmask = msm_gpio_irq_unmask;
>         pctrl->irq_chip.irq_ack = msm_gpio_irq_ack;
> +       pctrl->irq_chip.irq_eoi = irq_chip_eoi_parent;

This part and the functions called seem fine!

> +       dn = of_parse_phandle(pctrl->dev->of_node, "wakeup-parent", 0);
> +       if (dn) {
> +               int i;
> +               bool skip;
> +               unsigned int gpio;
> +
> +               chip->irq.parent_domain = irq_find_matching_host(dn,
> +                                                DOMAIN_BUS_WAKEUP);
> +               of_node_put(dn);
> +               if (!chip->irq.parent_domain)
> +                       return -EPROBE_DEFER;
> +               chip->irq.child_to_parent_hwirq = msm_gpio_wakeirq;
> +
> +               skip = irq_domain_qcom_handle_wakeup(chip->irq.parent_domain);
> +               for (i = 0; skip && i < pctrl->soc->nwakeirq_map; i++) {
> +                       gpio = pctrl->soc->wakeirq_map[i].gpio;
> +                       set_bit(gpio, pctrl->skip_wake_irqs);
> +               }
> +       }

OK I guess this is how we should do it, maybe add a comment to clarify
that we are checking the parent irqdomain of the chained IRQ to see
if we need to avoid disabling the irq as it is used for wakeup. (IIUC
what the code does!)

> +       /*
> +        * Since we are chained to the GIC using the TLMM summary line
> +        * and in hierarchy with the wakeup parent interrupt controller,
> +        * explicitly set the chained summary line. We need to do this because
> +        * the summary line is not routed to the wakeup parent but directly
> +        * to the GIC.
> +        */
> +       gpiochip_set_chained_irqchip(chip, &pctrl->irq_chip, pctrl->irq,
> +                                    msm_gpio_irq_handler);

I don't think this part is needed, we already have:

girq->parent_handler = msm_gpio_irq_handler;
girq->num_parents = 1;
girq->parents = devm_kcalloc(pctrl->dev, 1, sizeof(*girq->parents),
     GFP_KERNEL);
if (!girq->parents)
     return -ENOMEM;
girq->default_type = IRQ_TYPE_NONE;
girq->handler = handle_bad_irq;
girq->parents[0] = pctrl->irq;

This will make the irq chain when calling gpiochip_add_data(), so
just delete this and see if everything works as before.

Other than that it looks fine!

Yours,
Linus Walleij
Lina Iyer Nov. 13, 2019, 6:35 p.m. UTC | #2
On Thu, Oct 03 2019 at 06:17 -0600, Linus Walleij wrote:
>On Fri, Sep 13, 2019 at 11:59 PM Lina Iyer <ilina@codeaurora.org> wrote:
>
>> Some GPIOs are marked as wakeup capable and are routed to another
>> interrupt controller that is an always-domain and can detect interrupts
>> even most of the SoC is powered off. The wakeup interrupt controller
>> wakes up the GIC and replays the interrupt at the GIC.
>>
>> Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
>> and ensure the wakeup GPIOs are handled correctly.
>>
>> Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
>> Signed-off-by: Lina Iyer <ilina@codeaurora.org>
>> ----
>> Changes in RFC v2:
>>         - Define irq_domain_qcom_handle_wakeup()
>>         - Rebase on top of GPIO hierarchy support in linux-next
>>         - Set the chained irq handler for summary line
>
>This is looking better every time I look at it, it's really complex
>but alas the problem is hard to solve so it requires complex solutions.
>
>> @@ -1006,6 +1091,7 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
>>         struct gpio_irq_chip *girq;
>>         int ret;
>>         unsigned ngpio = pctrl->soc->ngpios;
>> +       struct device_node *dn;
>
>I usually call the variable "np"
>
Will change.

>> @@ -1021,17 +1107,40 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
>>
>>         pctrl->irq_chip.name = "msmgpio";
>>         pctrl->irq_chip.irq_enable = msm_gpio_irq_enable;
>> +       pctrl->irq_chip.irq_disable = msm_gpio_irq_disable;
>>         pctrl->irq_chip.irq_mask = msm_gpio_irq_mask;
>>         pctrl->irq_chip.irq_unmask = msm_gpio_irq_unmask;
>>         pctrl->irq_chip.irq_ack = msm_gpio_irq_ack;
>> +       pctrl->irq_chip.irq_eoi = irq_chip_eoi_parent;
>
>This part and the functions called seem fine!
>
>> +       dn = of_parse_phandle(pctrl->dev->of_node, "wakeup-parent", 0);
>> +       if (dn) {
>> +               int i;
>> +               bool skip;
>> +               unsigned int gpio;
>> +
>> +               chip->irq.parent_domain = irq_find_matching_host(dn,
>> +                                                DOMAIN_BUS_WAKEUP);
>> +               of_node_put(dn);
>> +               if (!chip->irq.parent_domain)
>> +                       return -EPROBE_DEFER;
>> +               chip->irq.child_to_parent_hwirq = msm_gpio_wakeirq;
>> +
>> +               skip = irq_domain_qcom_handle_wakeup(chip->irq.parent_domain);
>> +               for (i = 0; skip && i < pctrl->soc->nwakeirq_map; i++) {
>> +                       gpio = pctrl->soc->wakeirq_map[i].gpio;
>> +                       set_bit(gpio, pctrl->skip_wake_irqs);
>> +               }
>> +       }
>
>OK I guess this is how we should do it, maybe add a comment to clarify
>that we are checking the parent irqdomain of the chained IRQ to see
>if we need to avoid disabling the irq as it is used for wakeup. (IIUC
>what the code does!)
>
Okay.

>> +       /*
>> +        * Since we are chained to the GIC using the TLMM summary line
>> +        * and in hierarchy with the wakeup parent interrupt controller,
>> +        * explicitly set the chained summary line. We need to do this because
>> +        * the summary line is not routed to the wakeup parent but directly
>> +        * to the GIC.
>> +        */
>> +       gpiochip_set_chained_irqchip(chip, &pctrl->irq_chip, pctrl->irq,
>> +                                    msm_gpio_irq_handler);
>
>I don't think this part is needed, we already have:
>
>girq->parent_handler = msm_gpio_irq_handler;
>girq->num_parents = 1;
>girq->parents = devm_kcalloc(pctrl->dev, 1, sizeof(*girq->parents),
>     GFP_KERNEL);
>if (!girq->parents)
>     return -ENOMEM;
>girq->default_type = IRQ_TYPE_NONE;
>girq->handler = handle_bad_irq;
>girq->parents[0] = pctrl->irq;
>
>This will make the irq chain when calling gpiochip_add_data(), so
>just delete this and see if everything works as before.
>
I thought it didn't work without this change and I am not sure why it
started working after I did. May be it was a bad set of patches that I
pulled in.

>Other than that it looks fine!
Thanks for your review.

--Lina
diff mbox series

Patch

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index f355ddd..c5ba389 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -23,6 +23,8 @@ 
 #include <linux/pm.h>
 #include <linux/log2.h>
 
+#include <linux/soc/qcom/irq.h>
+
 #include "../core.h"
 #include "../pinconf.h"
 #include "pinctrl-msm.h"
@@ -44,6 +46,7 @@ 
  * @enabled_irqs:   Bitmap of currently enabled irqs.
  * @dual_edge_irqs: Bitmap of irqs that need sw emulated dual edge
  *                  detection.
+ * @skip_wake_irqs: Skip IRQs that are handled by wakeup interrupt contrroller
  * @soc;            Reference to soc_data of platform specific data.
  * @regs:           Base addresses for the TLMM tiles.
  */
@@ -61,6 +64,7 @@  struct msm_pinctrl {
 
 	DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
 	DECLARE_BITMAP(enabled_irqs, MAX_NR_GPIO);
+	DECLARE_BITMAP(skip_wake_irqs, MAX_NR_GPIO);
 
 	const struct msm_pinctrl_soc_data *soc;
 	void __iomem *regs[MAX_NR_TILES];
@@ -709,6 +713,12 @@  static void msm_gpio_irq_mask(struct irq_data *d)
 	unsigned long flags;
 	u32 val;
 
+	if (d->parent_data)
+		irq_chip_mask_parent(d);
+
+	if (test_bit(d->hwirq, pctrl->skip_wake_irqs))
+		return;
+
 	g = &pctrl->soc->groups[d->hwirq];
 
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
@@ -753,6 +763,12 @@  static void msm_gpio_irq_clear_unmask(struct irq_data *d, bool status_clear)
 	unsigned long flags;
 	u32 val;
 
+	if (d->parent_data)
+		irq_chip_unmask_parent(d);
+
+	if (test_bit(d->hwirq, pctrl->skip_wake_irqs))
+		return;
+
 	g = &pctrl->soc->groups[d->hwirq];
 
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
@@ -780,10 +796,37 @@  static void msm_gpio_irq_clear_unmask(struct irq_data *d, bool status_clear)
 
 static void msm_gpio_irq_enable(struct irq_data *d)
 {
+	/*
+	 * Clear the interrupt that may be pending before we enable
+	 * the line.
+	 * This is especially a problem with the GPIOs routed to the
+	 * PDC. These GPIOs are direct-connect interrupts to the GIC.
+	 * Disabling the interrupt line at the PDC does not prevent
+	 * the interrupt from being latched at the GIC. The state at
+	 * GIC needs to be cleared before enabling.
+	 */
+	if (d->parent_data) {
+		irq_chip_set_parent_state(d, IRQCHIP_STATE_PENDING, 0);
+		irq_chip_enable_parent(d);
+	}
 
 	msm_gpio_irq_clear_unmask(d, true);
 }
 
+static void msm_gpio_irq_disable(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
+
+	if (d->parent_data)
+		irq_chip_disable_parent(d);
+
+	if (test_bit(d->hwirq, pctrl->skip_wake_irqs))
+		return;
+
+	msm_gpio_irq_mask(d);
+}
+
 static void msm_gpio_irq_unmask(struct irq_data *d)
 {
 	msm_gpio_irq_clear_unmask(d, false);
@@ -797,6 +840,9 @@  static void msm_gpio_irq_ack(struct irq_data *d)
 	unsigned long flags;
 	u32 val;
 
+	if (test_bit(d->hwirq, pctrl->skip_wake_irqs))
+		return;
+
 	g = &pctrl->soc->groups[d->hwirq];
 
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
@@ -822,6 +868,12 @@  static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	unsigned long flags;
 	u32 val;
 
+	if (d->parent_data)
+		irq_chip_set_type_parent(d, type);
+
+	if (test_bit(d->hwirq, pctrl->skip_wake_irqs))
+		return 0;
+
 	g = &pctrl->soc->groups[d->hwirq];
 
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
@@ -914,6 +966,15 @@  static int msm_gpio_irq_set_wake(struct irq_data *d, unsigned int on)
 	struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
 	unsigned long flags;
 
+	if (d->parent_data)
+		irq_chip_set_wake_parent(d, on);
+
+	/*
+	 * While they may not wake up when the TLMM is powered off,
+	 * some GPIOs would like to wakeup the system from suspend
+	 * when TLMM is powered on. To allow that, enable the GPIO
+	 * summary line to be wakeup capable at GIC.
+	 */
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
 
 	irq_set_irq_wake(pctrl->irq, on);
@@ -992,6 +1053,30 @@  static void msm_gpio_irq_handler(struct irq_desc *desc)
 	chained_irq_exit(chip, desc);
 }
 
+static int msm_gpio_wakeirq(struct gpio_chip *gc,
+			    unsigned int child,
+			    unsigned int child_type,
+			    unsigned int *parent,
+			    unsigned int *parent_type)
+{
+	struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
+	const struct msm_gpio_wakeirq_map *map;
+	int i;
+
+	*parent = GPIO_NO_WAKE_IRQ;
+	*parent_type = IRQ_TYPE_EDGE_RISING;
+
+	for (i = 0; i < pctrl->soc->nwakeirq_map; i++) {
+		map = &pctrl->soc->wakeirq_map[i];
+		if (map->gpio == child) {
+			*parent = map->wakeirq;
+			break;
+		}
+	}
+
+	return 0;
+}
+
 static bool msm_gpio_needs_valid_mask(struct msm_pinctrl *pctrl)
 {
 	if (pctrl->soc->reserved_gpios)
@@ -1006,6 +1091,7 @@  static int msm_gpio_init(struct msm_pinctrl *pctrl)
 	struct gpio_irq_chip *girq;
 	int ret;
 	unsigned ngpio = pctrl->soc->ngpios;
+	struct device_node *dn;
 
 	if (WARN_ON(ngpio > MAX_NR_GPIO))
 		return -EINVAL;
@@ -1021,17 +1107,40 @@  static int msm_gpio_init(struct msm_pinctrl *pctrl)
 
 	pctrl->irq_chip.name = "msmgpio";
 	pctrl->irq_chip.irq_enable = msm_gpio_irq_enable;
+	pctrl->irq_chip.irq_disable = msm_gpio_irq_disable;
 	pctrl->irq_chip.irq_mask = msm_gpio_irq_mask;
 	pctrl->irq_chip.irq_unmask = msm_gpio_irq_unmask;
 	pctrl->irq_chip.irq_ack = msm_gpio_irq_ack;
+	pctrl->irq_chip.irq_eoi = irq_chip_eoi_parent;
 	pctrl->irq_chip.irq_set_type = msm_gpio_irq_set_type;
 	pctrl->irq_chip.irq_set_wake = msm_gpio_irq_set_wake;
 	pctrl->irq_chip.irq_request_resources = msm_gpio_irq_reqres;
 	pctrl->irq_chip.irq_release_resources = msm_gpio_irq_relres;
 
+	dn = of_parse_phandle(pctrl->dev->of_node, "wakeup-parent", 0);
+	if (dn) {
+		int i;
+		bool skip;
+		unsigned int gpio;
+
+		chip->irq.parent_domain = irq_find_matching_host(dn,
+						 DOMAIN_BUS_WAKEUP);
+		of_node_put(dn);
+		if (!chip->irq.parent_domain)
+			return -EPROBE_DEFER;
+		chip->irq.child_to_parent_hwirq = msm_gpio_wakeirq;
+
+		skip = irq_domain_qcom_handle_wakeup(chip->irq.parent_domain);
+		for (i = 0; skip && i < pctrl->soc->nwakeirq_map; i++) {
+			gpio = pctrl->soc->wakeirq_map[i].gpio;
+			set_bit(gpio, pctrl->skip_wake_irqs);
+		}
+	}
+
 	girq = &chip->irq;
 	girq->chip = &pctrl->irq_chip;
 	girq->parent_handler = msm_gpio_irq_handler;
+	girq->fwnode = pctrl->dev->fwnode;
 	girq->num_parents = 1;
 	girq->parents = devm_kcalloc(pctrl->dev, 1, sizeof(*girq->parents),
 				     GFP_KERNEL);
@@ -1067,6 +1176,16 @@  static int msm_gpio_init(struct msm_pinctrl *pctrl)
 		}
 	}
 
+	/*
+	 * Since we are chained to the GIC using the TLMM summary line
+	 * and in hierarchy with the wakeup parent interrupt controller,
+	 * explicitly set the chained summary line. We need to do this because
+	 * the summary line is not routed to the wakeup parent but directly
+	 * to the GIC.
+	 */
+	gpiochip_set_chained_irqchip(chip, &pctrl->irq_chip, pctrl->irq,
+				     msm_gpio_irq_handler);
+
 	return 0;
 }
 
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.h b/drivers/pinctrl/qcom/pinctrl-msm.h
index 48569cda8..1547020 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.h
+++ b/drivers/pinctrl/qcom/pinctrl-msm.h
@@ -5,6 +5,8 @@ 
 #ifndef __PINCTRL_MSM_H__
 #define __PINCTRL_MSM_H__
 
+#include <linux/gpio/driver.h>
+
 struct pinctrl_pin_desc;
 
 /**
@@ -92,6 +94,16 @@  struct msm_pingroup {
 };
 
 /**
+ * struct msm_gpio_wakeirq_map - Map of GPIOs and their wakeup pins
+ * @gpio:          The GPIOs that are wakeup capable
+ * @wakeirq:       The interrupt at the always-on interrupt controller
+ */
+struct msm_gpio_wakeirq_map {
+	unsigned int gpio;
+	unsigned int wakeirq;
+};
+
+/**
  * struct msm_pinctrl_soc_data - Qualcomm pin controller driver configuration
  * @pins:	    An array describing all pins the pin controller affects.
  * @npins:	    The number of entries in @pins.
@@ -101,6 +113,8 @@  struct msm_pingroup {
  * @ngroups:	    The numbmer of entries in @groups.
  * @ngpio:	    The number of pingroups the driver should expose as GPIOs.
  * @pull_no_keeper: The SoC does not support keeper bias.
+ * @wakeirq_map:    The map of wakeup capable GPIOs and the pin at PDC/MPM
+ * @nwakeirq_map:   The number of entries in @hierarchy_map
  */
 struct msm_pinctrl_soc_data {
 	const struct pinctrl_pin_desc *pins;
@@ -114,6 +128,8 @@  struct msm_pinctrl_soc_data {
 	const char *const *tiles;
 	unsigned int ntiles;
 	const int *reserved_gpios;
+	const struct msm_gpio_wakeirq_map *wakeirq_map;
+	unsigned int nwakeirq_map;
 };
 
 extern const struct dev_pm_ops msm_pinctrl_dev_pm_ops;
diff --git a/include/linux/soc/qcom/irq.h b/include/linux/soc/qcom/irq.h
index 85ac4b6..098d57c 100644
--- a/include/linux/soc/qcom/irq.h
+++ b/include/linux/soc/qcom/irq.h
@@ -16,4 +16,17 @@ 
 #define IRQ_DOMAIN_FLAG_QCOM_PDC_WAKEUP		(IRQ_DOMAIN_FLAG_NONCORE << 0)
 #define IRQ_DOMAIN_FLAG_QCOM_MPM_WAKEUP		(IRQ_DOMAIN_FLAG_NONCORE << 1)
 
+/**
+ * irq_domain_qcom_handle_wakeup: Return if the domain handles interrupt
+ *                                configuration
+ * @parent: irq domain
+ *
+ * This QCOM specific irq domain call returns if the interrupt controller
+ * requires the interrupt be masked at the child interrupt controller.
+ */
+static inline bool irq_domain_qcom_handle_wakeup(struct irq_domain *parent)
+{
+	return (parent->flags & IRQ_DOMAIN_FLAG_QCOM_PDC_WAKEUP);
+}
+
 #endif