diff mbox series

[v6,4/5] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB

Message ID 1586472749-18599-5-git-send-email-wcheng@codeaurora.org (mailing list archive)
State Superseded
Headers show
Series Add SS/HS-USB changes for Qualcomm SM8150 chipset | expand

Commit Message

Wesley Cheng April 9, 2020, 10:52 p.m. UTC 
The register map for SM8150 QMP USB SSPHY has moved
QPHY_POWER_DOWN_CONTROL to a different offset.  Allow for
an offset in the register table to override default value
if it is a DP capable PHY.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index cc04471..5363a99 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -119,6 +119,7 @@  enum qphy_reg_layout {
 	QPHY_PCS_AUTONOMOUS_MODE_CTRL,
 	QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
 	QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
+	QPHY_PCS_POWER_DOWN_CONTROL,
 };
 
 static const unsigned int pciephy_regs_layout[] = {
@@ -164,6 +165,7 @@  enum qphy_reg_layout {
 	[QPHY_SW_RESET]			= 0x00,
 	[QPHY_START_CTRL]		= 0x44,
 	[QPHY_PCS_STATUS]		= 0x14,
+	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
 };
 
 static const unsigned int sdm845_ufsphy_regs_layout[] = {
@@ -1624,11 +1626,16 @@  static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 			     SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
 	}
 
-	if (cfg->has_phy_com_ctrl)
+	if (cfg->has_phy_com_ctrl) {
 		qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
 			     SW_PWRDN);
-	else
-		qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+	} else {
+		if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL])
+			qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+					cfg->pwrdn_ctrl);
+		else
+			qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+	}
 
 	/* Serdes configuration */
 	qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
@@ -1850,7 +1857,12 @@  static int qcom_qmp_phy_disable(struct phy *phy)
 	qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
 
 	/* Put PHY into POWER DOWN state: active low */
-	qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+	if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL]) {
+		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+			     cfg->pwrdn_ctrl);
+	} else {
+		qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+	}
 
 	if (cfg->has_lane_rst)
 		reset_control_assert(qphy->lane_rst);