diff mbox series

[07/23] ARM: dts: qcom-msm8974*: Rename msmgpio to tlmm

Message ID 20220415115633.575010-8-konrad.dybcio@somainline.org (mailing list archive)
State Accepted
Headers show
Series [01/23] ARM: dts: qcom-*-sony*: Mention SONY board names in DT filenames | expand

Commit Message

Konrad Dybcio April 15, 2022, 11:56 a.m. UTC
Rename the label to match new the style used in newer DTs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 .../arm/boot/dts/qcom-apq8074-dragonboard.dts |  2 +-
 .../boot/dts/qcom-msm8974-fairphone-fp2.dts   |  2 +-
 .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 18 ++++++++---------
 .../boot/dts/qcom-msm8974-samsung-klte.dts    | 20 +++++++++----------
 .../qcom-msm8974-sony-xperia-rhine-amami.dts  |  2 +-
 .../qcom-msm8974-sony-xperia-rhine-honami.dts |  4 ++--
 ...com-msm8974-sony-xperia-shinano-castor.dts | 10 +++++-----
 arch/arm/boot/dts/qcom-msm8974.dtsi           |  4 ++--
 8 files changed, 31 insertions(+), 31 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index 83793b835d40..f8983739fe4c 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -35,7 +35,7 @@  sdhci@f9824900 {
 		};
 
 		sdhci@f98a4900 {
-			cd-gpios = <&msmgpio 62 0x1>;
+			cd-gpios = <&tlmm 62 0x1>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
 			bus-width = <4>;
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
index 6d77e0f8ca4d..c502a059f090 100644
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
@@ -51,7 +51,7 @@  volume-up {
 
 	vibrator {
 		compatible = "gpio-vibrator";
-		enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
 		vcc-supply = <&pm8941_l18>;
 	};
 
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 7bd577e8e941..cf06d4a17097 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -229,7 +229,7 @@  vreg_wlan: wlan-regulator {
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
-		gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 
 		pinctrl-names = "default";
@@ -482,9 +482,9 @@  bluetooth {
 			pinctrl-names = "default";
 			pinctrl-0 = <&bt_pin>;
 
-			host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
+			host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+			device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -522,7 +522,7 @@  i2c@f9968000 {
 		mpu6515@68 {
 			compatible = "invensense,mpu6515";
 			reg = <0x68>;
-			interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
 			vddio-supply = <&pm8941_lvs1>;
 
 			pinctrl-names = "default";
@@ -538,7 +538,7 @@  i2c-gate {
 				ak8963@f {
 					compatible = "asahi-kasei,ak8963";
 					reg = <0x0f>;
-					gpios = <&msmgpio 67 0>;
+					gpios = <&tlmm 67 0>;
 					vid-supply = <&pm8941_lvs1>;
 					vdd-supply = <&pm8941_l17>;
 				};
@@ -577,7 +577,7 @@  fuelgauge: max17048@36 {
 			maxim,double-soc;
 			maxim,rcomp = /bits/ 8 <0x4d>;
 
-			interrupt-parent = <&msmgpio>;
+			interrupt-parent = <&tlmm>;
 			interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
 
 			pinctrl-names = "default";
@@ -600,7 +600,7 @@  synaptics@70 {
 			compatible = "syna,rmi4-i2c";
 			reg = <0x70>;
 
-			interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
 			vdd-supply = <&pm8941_l22>;
 			vio-supply = <&pm8941_lvs3>;
 
@@ -632,7 +632,7 @@  i2c@f9925000 {
 		avago_apds993@39 {
 			compatible = "avago,apds9930";
 			reg = <0x39>;
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
 			vdd-supply = <&pm8941_l17>;
 			vddio-supply = <&pm8941_lvs1>;
 			led-max-microamp = <100000>;
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
index 571b396f32cf..daafc4d31fc5 100644
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
@@ -215,8 +215,8 @@  i2c-gpio-touchkey {
 		compatible = "i2c-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		sda-gpios = <&msmgpio 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&msmgpio 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c_touchkey_pins>;
 
@@ -240,8 +240,8 @@  i2c-gpio-led {
 		compatible = "i2c-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		scl-gpios = <&msmgpio 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		sda-gpios = <&msmgpio 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c_led_gpioex_pins>;
 
@@ -259,7 +259,7 @@  gpio_expander: gpio@20 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&gpioex_pin>;
 
-			reset-gpios = <&msmgpio 145 GPIO_ACTIVE_LOW>;
+			reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
 		};
 
 		led-controller@30 {
@@ -339,9 +339,9 @@  bluetooth {
 			max-speed = <3000000>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&bt_pins>;
-			device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
+			device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
 			shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
-			interrupt-parent = <&msmgpio>;
+			interrupt-parent = <&tlmm>;
 			interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "host-wakeup";
 		};
@@ -563,7 +563,7 @@  sdhci@f9864900 {
 		 */
 		pinctrl-names = "default";
 		pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
-		// cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+		// cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 	};
 
 	sdhci@f98a4900 {
@@ -587,7 +587,7 @@  wifi@1 {
 			reg = <1>;
 			compatible = "brcm,bcm4329-fmac";
 
-			interrupt-parent = <&msmgpio>;
+			interrupt-parent = <&tlmm>;
 			interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "host-wake";
 
@@ -818,7 +818,7 @@  panel: panel@0 {
 				vddr-supply = <&vreg_panel>;
 
 				reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
-				te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+				te-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
 				port {
 					panel_in: endpoint {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
index 79e2cfbbb1ba..b8b35f000813 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -280,7 +280,7 @@  sdhci@f98a4900 {
 		vmmc-supply = <&pm8941_l21>;
 		vqmmc-supply = <&pm8941_l13>;
 
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+		cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
index a62e5c25b23c..1f04f8493784 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -305,7 +305,7 @@  sdhci@f98a4900 {
 		vmmc-supply = <&pm8941_l21>;
 		vqmmc-supply = <&pm8941_l13>;
 
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+		cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
@@ -331,7 +331,7 @@  synaptics@2c {
 			compatible = "syna,rmi4-i2c";
 			reg = <0x2c>;
 
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-shinano-castor.dts
index d0d03ef12c31..d77540205594 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-shinano-castor.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-shinano-castor.dts
@@ -239,7 +239,7 @@  vreg_bl_vddio: lcd-backlight-vddio {
 		regulator-min-microvolt = <3150000>;
 		regulator-max-microvolt = <3150000>;
 
-		gpio = <&msmgpio 69 0>;
+		gpio = <&tlmm 69 0>;
 		enable-active-high;
 
 		vin-supply = <&pm8941_s3>;
@@ -323,7 +323,7 @@  sdhci@f98a4900 {
 		vmmc-supply = <&pm8941_l21>;
 		vqmmc-supply = <&pm8941_l13>;
 
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+		cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
@@ -351,8 +351,8 @@  bluetooth {
 				    <&bt_dev_wake_pin>,
 				    <&bt_reg_on_pin>;
 
-			host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
+			host-wakeup-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+			device-wakeup-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
 			shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
 		};
 	};
@@ -566,7 +566,7 @@  synaptics@2c {
 			compatible = "syna,rmi4-i2c";
 			reg = <0x2c>;
 
-			interrupt-parent = <&msmgpio>;
+			interrupt-parent = <&tlmm>;
 			interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
 
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 5392c595e5ec..ecc230c4f324 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -953,11 +953,11 @@  wifi {
 			};
 		};
 
-		msmgpio: pinctrl@fd510000 {
+		tlmm: pinctrl@fd510000 {
 			compatible = "qcom,msm8974-pinctrl";
 			reg = <0xfd510000 0x4000>;
 			gpio-controller;
-			gpio-ranges = <&msmgpio 0 0 146>;
+			gpio-ranges = <&tlmm 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;