diff mbox series

[1/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5

Message ID 20240329-v2-dts-add-support-for-samsung-galaxy-zfold5-v1-1-9a91e635cacc@yahoo.com (mailing list archive)
State Changes Requested
Headers show
Series V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5 | expand

Commit Message

Alexandru Marc Serdeliuc via B4 Relay March 28, 2024, 11:08 p.m. UTC 
From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>

Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone

Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons

Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
 arch/arm64/boot/dts/qcom/Makefile               |   1 +
 arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 584 ++++++++++++++++++++++++
 2 files changed, 585 insertions(+)

Comments

Konrad Dybcio March 29, 2024, 12:52 a.m. UTC | #1 
On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> 
> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
> 
> Currently working features:
> - Framebuffer
> - UFS
> - i2c
> - Buttons
> 
> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> ---

Your commit title now includes "V2". Move it inside the square braces the
next time around, so it's like [PATCH v3 1/2]. With b4, this should be done
automagically, though..

[...]

> +/ {
> +	model = "Samsung Galaxy Z Fold5";
> +	compatible = "samsung,q5q", "qcom,sm8550";
> +	#address-cells = <0x02>;
> +	#size-cells = <0x02>;

These two can go

[...]

> +	reserved-memory {
> +		/*
> +		 * The bootloader will only keep display hardware enabled
> +		 * if this memory region is named exactly 'splash_region'
> +		 */

Ouch.

[...]

> +		vreg_l15b_1p8: ldo15 {
> +			regulator-name = "vreg_l15b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +			regulator-always-on;

Any particular reason as to why?

[...]

> +&remoteproc_adsp {
> +	firmware-name = "qcom/sm8550/adsp.mbn",
> +			"qcom/sm8550/adsp_dtb.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> +	firmware-name = "qcom/sm8550/cdsp.mbn",
> +			"qcom/sm8550/cdsp_dtb.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_mpss {
> +	firmware-name = "qcom/sm8550/modem.mbn",
> +			"qcom/sm8550/modem_dtb.mbn";
> +	status = "okay";

Unless you stole one from the factory, these firmwares will not
load on your phone..

> +};
> +
> +&sleep_clk {
> +	clock-frequency = <32000>;
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <36 4>, <50 2>;

Would you have an idea what these GPIOs are used for?

Konrad
Alexandru Serdeliuc March 29, 2024, 9:42 a.m. UTC | #2 
Thanks, i added some notes inline as I do not know how to proceed with 
some if the requirements.

Just to be noted, the sm8550-samsung-q5q.dts it is based on 
sm8550-mtp.dts so most of the stuff is from there


On 29/3/24 1:52, Konrad Dybcio wrote:
> On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
>> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>>
>> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>>
>> Currently working features:
>> - Framebuffer
>> - UFS
>> - i2c
>> - Buttons
>>
>> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>> ---
The [PATCH] string is added automatically to the subject by b4, I don't 
know how to add/insert custom text in there, I am going to read the b4 
docs and see if i can spot how to do it.
> Your commit title now includes "V2". Move it inside the square braces the
> next time around, so it's like [PATCH v3 1/2]. With b4, this should be done
> automagically, though..
>
> [...]
>
>> +/ {
>> +	model = "Samsung Galaxy Z Fold5";
>> +	compatible = "samsung,q5q", "qcom,sm8550";
>> +	#address-cells = <0x02>;
>> +	#size-cells = <0x02>;

thanks, going to remove them

> These two can go
>
> [...]
>
>> +	reserved-memory {
>> +		/*
>> +		 * The bootloader will only keep display hardware enabled
>> +		 * if this memory region is named exactly 'splash_region'
>> +		 */
this is a reality, without it the framebuffer do not work, due to abl

https://git.codelinaro.org/clo/la/abl/tianocore/edk2/-/blob/LA.VENDOR.1.0.r2-09400-WAIPIO.QSSI14.0/QcomModulePkg/Library/BootLib/UpdateDeviceTree.c?ref_type=tags#L220

How to proceed?

> Ouch.
>
> [...]
>
>> +		vreg_l15b_1p8: ldo15 {
>> +			regulator-name = "vreg_l15b_1p8";
>> +			regulator-min-microvolt = <1800000>;
>> +			regulator-max-microvolt = <1800000>;
>> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> +			regulator-allow-set-load;
>> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> +						   RPMH_REGULATOR_MODE_HPM>;
>> +			regulator-always-on;

I have removed the nodes that uses this as the driver for "Texas 
Instruments i2c eUSB2" is not yet submitted by the porter, however, 
those are took from the existing sm8550-mtp.dts

How to proceed?

> Any particular reason as to why?
>
> [...]
>
>> +&remoteproc_adsp {
>> +	firmware-name = "qcom/sm8550/adsp.mbn",
>> +			"qcom/sm8550/adsp_dtb.mbn";
>> +	status = "okay";
>> +};
>> +
>> +&remoteproc_cdsp {
>> +	firmware-name = "qcom/sm8550/cdsp.mbn",
>> +			"qcom/sm8550/cdsp_dtb.mbn";
>> +	status = "okay";
>> +};
>> +
>> +&remoteproc_mpss {
>> +	firmware-name = "qcom/sm8550/modem.mbn",
>> +			"qcom/sm8550/modem_dtb.mbn";
>> +	status = "okay";

Those are took from the device's running Android /firmware and load 
without error, I used this kind of firmware loaded on other devices as 
well and seems to do the job, the lines are as well on existing 
sm8550-mtp.dts

How to proceed?

> Unless you stole one from the factory, these firmwares will not
> load on your phone..
>
>> +};
>> +
>> +&sleep_clk {
>> +	clock-frequency = <32000>;
>> +};
>> +
>> +&tlmm {
>> +	gpio-reserved-ranges = <36 4>, <50 2>;
I have no idea, i took the ranges from  the running Android FDT, without 
those ranges the kernel do not boot, i can dig more into these ranges if 
required
> Would you have an idea what these GPIOs are used for?
>
> Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..a7503fd35b6c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx224.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-samsung-q5q.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
new file mode 100644
index 000000000000..aec375fc32b4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -0,0 +1,584 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
+ * Copyright (c) 2024, David Wronek <david@mainlining.org>
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/ {
+	model = "Samsung Galaxy Z Fold5";
+	compatible = "samsung,q5q", "qcom,sm8550";
+	#address-cells = <0x02>;
+	#size-cells = <0x02>;
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer: framebuffer@b8000000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			width = <2176>;
+			height = <1812>;
+			stride = <(2176 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reserved-memory {
+		/*
+		 * The bootloader will only keep display hardware enabled
+		 * if this memory region is named exactly 'splash_region'
+		 */
+		splash_region@b8000000 {
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			no-map;
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l3c_0p91: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s4e_0p9: smps4 {
+			regulator-name = "vreg_s4e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p1: smps5 {
+			regulator-name = "vreg_s5e_1p1";
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p91: ldo3 {
+			regulator-name = "vreg_l3f_0p91";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vreg_s1g_1p2: smps1 {
+			regulator-name = "vreg_s1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p8: smps2 {
+			regulator-name = "vreg_s2g_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p7: smps3 {
+			regulator-name = "vreg_s3g_0p7";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p3: smps4 {
+			regulator-name = "vreg_s4g_1p3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p8: smps5 {
+			regulator-name = "vreg_s5g_0p8";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p8: smps6 {
+			regulator-name = "vreg_s6g_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2g_1p2: ldo2 {
+			regulator-name = "vreg_l2g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+		qcom,pmic-id = "m";
+
+		vreg_l1m_1p056: ldo1 {
+			regulator-name = "vreg_l1m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2m_1p056: ldo2 {
+			regulator-name = "vreg_l2m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3m_2p8: ldo3 {
+			regulator-name = "vreg_l3m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4m_2p8: ldo4 {
+			regulator-name = "vreg_l4m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5m_1p8: ldo5 {
+			regulator-name = "vreg_l5m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6m_1p8: ldo6 {
+			regulator-name = "vreg_l6m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7m_2p9: ldo7 {
+			regulator-name = "vreg_l7m_2p9";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+		qcom,pmic-id = "n";
+
+		vreg_l1n_1p1: ldo1 {
+			regulator-name = "vreg_l1n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2n_1p1: ldo2 {
+			regulator-name = "vreg_l2n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3n_2p8: ldo3 {
+			regulator-name = "vreg_l3n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4n_2p8: ldo4 {
+			regulator-name = "vreg_l4n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5n_1p8: ldo5 {
+			regulator-name = "vreg_l5n_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6n_3p3: ldo6 {
+			regulator-name = "vreg_l6n_3p3";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7n_2p96: ldo7 {
+			regulator-name = "vreg_l7n_2p96";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+
+&dispcc {
+	status = "disabled";
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p91>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+	status = "okay";
+};
+
+&pm8550_gpios {
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/adsp.mbn",
+			"qcom/sm8550/adsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/cdsp.mbn",
+			"qcom/sm8550/cdsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sm8550/modem.mbn",
+			"qcom/sm8550/modem_dtb.mbn";
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <36 4>, <50 2>;
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};