@@ -82,7 +82,7 @@ static int slave_alloc (struct scsi_device *sdev)
return 0;
}
-static int slave_configure(struct scsi_device *sdev)
+static int device_configure(struct scsi_device *sdev, struct queue_limits *lim)
{
struct us_data *us = host_to_us(sdev->host);
struct device *dev = us->pusb_dev->bus->sysdev;
@@ -97,31 +97,28 @@ static int slave_configure(struct scsi_device *sdev)
if (us->fflags & US_FL_MAX_SECTORS_MIN)
max_sectors = PAGE_SIZE >> 9;
- if (queue_max_hw_sectors(sdev->request_queue) > max_sectors)
- blk_queue_max_hw_sectors(sdev->request_queue,
- max_sectors);
+ lim->max_hw_sectors = min(lim->max_hw_sectors, max_sectors);
} else if (sdev->type == TYPE_TAPE) {
/*
* Tapes need much higher max_sector limits, so just
* raise it to the maximum possible (4 GB / 512) and
* let the queue segment size sort out the real limit.
*/
- blk_queue_max_hw_sectors(sdev->request_queue, 0x7FFFFF);
+ lim->max_hw_sectors = 0x7FFFFF;
} else if (us->pusb_dev->speed >= USB_SPEED_SUPER) {
/*
* USB3 devices will be limited to 2048 sectors. This gives us
* better throughput on most devices.
*/
- blk_queue_max_hw_sectors(sdev->request_queue, 2048);
+ lim->max_hw_sectors = 2048;
}
/*
* The max_hw_sectors should be up to maximum size of a mapping for
* the device. Otherwise, a DMA API might fail on swiotlb environment.
*/
- blk_queue_max_hw_sectors(sdev->request_queue,
- min_t(size_t, queue_max_hw_sectors(sdev->request_queue),
- dma_max_mapping_size(dev) >> SECTOR_SHIFT));
+ lim->max_hw_sectors = min_t(size_t,
+ lim->max_hw_sectors, dma_max_mapping_size(dev) >> SECTOR_SHIFT);
/*
* We can't put these settings in slave_alloc() because that gets
@@ -582,13 +579,22 @@ static ssize_t max_sectors_store(struct device *dev, struct device_attribute *at
size_t count)
{
struct scsi_device *sdev = to_scsi_device(dev);
+ struct queue_limits lim;
unsigned short ms;
+ int ret;
- if (sscanf(buf, "%hu", &ms) > 0) {
- blk_queue_max_hw_sectors(sdev->request_queue, ms);
- return count;
- }
- return -EINVAL;
+ if (sscanf(buf, "%hu", &ms) <= 0)
+ return -EINVAL;
+
+ blk_mq_freeze_queue(sdev->request_queue);
+ lim = queue_limits_start_update(sdev->request_queue);
+ lim.max_hw_sectors = ms;
+ ret = queue_limits_commit_update(sdev->request_queue, &lim);
+ blk_mq_unfreeze_queue(sdev->request_queue);
+
+ if (ret)
+ return ret;
+ return count;
}
static DEVICE_ATTR_RW(max_sectors);
@@ -626,7 +632,7 @@ static const struct scsi_host_template usb_stor_host_template = {
.this_id = -1,
.slave_alloc = slave_alloc,
- .slave_configure = slave_configure,
+ .device_configure = device_configure,
.target_alloc = target_alloc,
/* lots of sg segments can be handled */
Switch to the ->device_configure method instead of ->slave_configure and update the block limits on the passed in queue_limits instead of using the per-limit accessors. Also use the proper atomic queue limit update helpers and freeze the queue when updating max_hw_sectors from sysfs. Signed-off-by: Christoph Hellwig <hch@lst.de> --- drivers/usb/storage/scsiglue.c | 36 ++++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 15 deletions(-)